Effect of Thickness on Direct Bonding of Silicon Nitride to Steel

The effects of specimen size, primarily the thickness of silicon nitride, on residual stress in a silicon nitride/steel joint were calculated using a finite-element method and studied experimentally by tensile tests of isostatically hot-pressed joints. The thicker joints had a low strength because of thermal expansion mismatch. When the silicon nitride was <0.2 mm thick, the strength of the joints reached 50 MPa.     

An Experimental Technique on the Dynamic Strength of Adhesively Bonded Single Lap Joints

This paper reported an experimental technique on the shear strength of adhesively bonded single lap joints subjected to impact loads by means of a split Hopkinson tensile bar. The experiments were conducted at two velocities (V = 20 m/s, 7 m/s) and testing temperatures ranging from ?40°C to 80°C. The results indicated that the shear strength of the specimen decreased with the increase of temperature and increased with the increase of velocity. The strength degradation from room temperature to high temperature was more severe than that from low temperature to room temperature. The effects of the pins, thermal stress and peel stress were also examined and found to have limited effects on the determination of the shear strength of the joints. It was concluded that the shear strength of the adhesively bonded single lap joints under impact loads can be determined by this experimental technique.     

Strength of Adhesively-Bonded Butt Joints of Tubes Subjected to Combined High-Rate Loads

The dynamic strength of adhesively-bonded joints was investigated experimentally. The strength of the bonded joints under combined high rate loading was measured using the clamped Hopkinson bar method. Tubular butt joints bonded by epoxy resin were used for the experiment. Combined stress waves of tension and torsion were applied to the specimens. The strength of the adhesively-bonded joint was determined by measuring the stress waves propagated in the load output tube of the specimen. It was found that the dynamic strength of the adhesive joints was greater than the static strength under tensile and shear load.     

Influence of adhesive bond line thickness on joint strength

While the geometry of aerospace assemblies is carefully controlled, for many industrial applications such as marine structures bond line thickness can vary significantly. In this study epoxy adhesive joints of different thicknesses between aluminium substrates have been characterized using physico-chemical analyses (differential scanning calorimetry, DSC; dynamic mechanical analysis, DMA; spectroscopy), nano-indentation and mechanical testing. Thermal analyses indicated no influence of thickness on structure. Nano-indentation revealed no evidence of an interphase at the metal/epoxy interface, nor any change in modulus for different thicknesses, though Raman spectroscopy suggested there may be slight variations in composition close to the substrates. However, mechanical testing using the modified Arcan fixture indicated a significant drop in strength and failure strain under pure tension and a smaller reduction for tension/shear and pure shear loads as thickness increased. Examination of sections through joints did not indicate any physical reason for this, but numerical analysis of the stress state revealed larger stress concentration factors for tensile loading in thick joints, which may explain the thickness effect. It is recommended that joint thickness should be kept below 0.8 mm to avoid obtaining artificially low values with the Arcan test.     

Effects of Processing Parameters on Tensile Strength of Thin-Wall HDPE Parts Injection Molded by Ultra High-Speed Process

This study explores how ultra high-speed processing parameters affect the melt flow length and tensile strength of thin-wall injection molded parts. A spiral shaped mold with a specimen thickness of 0.4 mm and a width of 6 mm was first constructed to test the melt flow length as an index of process capability for ultra high-speed injection molding. It was observed that the flow length increases with increasing injection speed. High-density polyethylene (HDPE) tensile test specimens with different thicknesses (0.6 mm and 2 mm) were also molded for tensile tests. Both single gate and double gates were used to form parts without and with weldlines. Injection molding trials were executed by systematically adjusting related parameters setting including mold temperature, melt temperature, and injection speed. The parts’ tensile strengths were measured experimentally. It was found that tensile strengths of 0.6 mm thick parts both with and without weldlines were higher than those of 2 mm thick parts. The tensile strength of 0.6 mm thick specimens increases with increasing mold temperature, melt temperature and injection speed, whereas tensile strength in 2 mm thick specimens was only weakly dependent on the corresponding processing parameters. Furthermore, 0.6 mm thick specimens with weldlines had tensile strengths lowered about 9.6% compared to parts without weldlines. For 2 mm thick part the corresponding reduction is 4.3%.     

Torsional shear strength behavior of advanced glass-ceramic sealants for SOFC/SOEC applications

Since reliable long term operation of SOFC and SOEC devices depends critically on the mechanical behavior of the sealant material, the current work focuses on the characterization of the shear strength by a torsion test of two different glass-ceramic sealants that are used to join Crofer22APU substrates in an application relevant configuration. The two glass-ceramic sealants differ in terms of characteristic temperatures and crystalline phases with possible impications on the joining behavior. Statistically identical shear stress values were measured at room temperature for joined hourglasses of different size with both sealants, thus confirming a size independence of the measured strength values. Experimental post-test examination results confirm that the interfaces play a strong role regarding the measured shear strength and provide important insights with respect to integration of metallic and glass-ceramic components in SOFC/SOEC stacks.     

层合板复合材料的层间剪切强度评价方法及其改进研究

针对国际上目前主要使用的双切口拉伸/压缩式层间剪切试验方法存在的问题,吸收了拉伸与压缩式试验方法各自的优点,对试验夹具及试验片形状与尺寸进行了改进设计,提出了双切口开孔拉伸式新的层间剪切强度测试、评价方法.以玻璃纤维平纹织物/环氧树脂复合材料层合板为试验材料对改进后的试验方法进行了实验及有限元分析.实验发现,表观层间剪切强度随槽间距的减小而有增大的趋势.通过有限元分析,对实验结果进行了解释,并确立了可获得真实层间剪切强度的最佳试验片尺寸.     

A Preliminary Study of the Use of Kynar® Piezoelectric Film to Measure Peel Stresses in Adhesive Joints

A variety of test techniques have been developed to test the performance of adhesives bonded in situ within joints. Most of these techniques measure strength, fracture toughness, or adhesive modulus of the bonded joint. Techniques to measure actual stress or strain values within a bonded joint are quite few in number. The Krieger gage¹ is able to measure the average shear displacement along a 12.5 mm. gage length of a thick adherend joint. It has been used primarily to measure in situ shear moduli of adhesives. Brinson and his colleagues² proposed bonding strain gages within adhesive joints to measure strains within the adhesive. Unfortunately, these gages are only sensitive to the lateral strains and not shear or peel strains. Because the lateral strains are dominated by the behavior of the adherends rather than the adhesive, the information which can be gained is incomplete.     

Interlaminar shear behaviors of 2D needled C/SiC composites under compressive and tensile loading

The interlaminar shear strength of 2D needled C/SiC composites was measured using the double-notch shear test method. Interlaminar shear tests were performed under compressive and tensile loading. Shear stress–strain response and shear strain field evolution were studied using the digital image correlation (DIC) technique. The results show that the interlaminar shear strength of the specimen using the compressive loading method is 15% higher than that of the tensile loading method. Severe shear strain concentration was observed near the upper notch of the tensile loading specimen. Acoustic emission (AE) was utilized to monitor the damage during the tests. Typical damage mechanisms were categorized according to AE signal characteristics. The statistical results show that more matrix cracks were produced in the tensile loading specimen and no separate fiber/matrix debonding signal was detected in both specimens.     

Shear properties of isotropic conductive adhesive joints under different loading rates

Epoxy-based conductive adhesives have been widely used in the electronic field given the lead-free development of electronic packaging. The conductive adhesive joints must be subjected to shear loads during the service of electronic products considering the mismatch in mechanical properties between packaged chip and substrate. In this study, INSTRON 5544 universal material testing machine was used for tensile–shear tests of isotropic conductive adhesive joint specimens, which were prepared using pure copper plate adherend in the form of single-lap joints. Four loading rates, that is, 0.05, 0.5, 5, and 10 mm/min, were adopted. The relationship between shear load and displacement of two overlapping copper plates is deduced from a mechanical perspective. A mechanical model of the conductive adhesive shear specimen was developed by introducing dimensionless parameters, which are obtained from interfacial fracture energy and shear strength, to interpret the effect of loading rate on the shear properties of the conductive adhesive specimen considering the loading rate. Results show that this model can effectively reflect the relationship between shear load and displacement in the range of 0.05–10 mm/min.     

Evaluation of a structural epoxy adhesive for timber-glass bonds under shear loading and different environmental conditions

This article presents a study of timber-glass adhesive joints. It examines the shear specimen and shear tools preparation process and the evaluation of the results backed up with an overview of existing similar studies. The chosen adhesive was a cold-curing two-component structural bonding epoxy resin (Mapei Adesilex PG1). The shear tests were performed under different temperatures and the timber samples had different moisture contents. A simple shear test tool was designed and was clamped into a universal testing machine for the shear test. The force and crosshead displacement values from the universal testing machine were used for evaluating the results. The environmental conditions of 20 °C and 5% timber moisture content resulted in the highest average shear strength obtained from the shear tests of the analysed joints (9.89 MPa), whereas the environmental conditions of 50 °C and 20% timber moisture content resulted in the lowest average shear strength (3.42 MPa). It was found that the joint strength is dependent on the environmental temperature and timber moisture content. Moreover, the shear specimen load-displacement behaviour at the environmental temperature of 50 °C was linear and nonlinear – depending on the timber moisture content. The most frequent failure type was timber failure. Additionally, a nonlinear contact finite element analysis was performed to demonstrate the additional shear specimen rotation due to the clearance between the shear specimen and shear tools. This impact was evaluated regarding the stress distribution in the bond line. The evaluated epoxy resin adhesive was proved to be suitable for timber-glass bonds.     

平纹编织C/SiC复合材料的失效判据

通过Arcan夹具拉伸实验,研究了平纹编织C/SiC复合材料的唯象强度特性,根据实验结果提出了一种椭圆形失效判据,可以反映拉压强度的差异,以及压缩和剪切同时作用时裂纹面闭合引起最大容许剪应力的回升.结果表明：椭圆形判据和实验结果在第一象限吻合良好,说明椭圆判据在第一象限内对平纹编织C/SiC是适用的.用线弹性有限元方法分析了Arcan拉伸实验中试样的应力状态和分布,并讨论了夹具刚度的影响.分析表明：试样缺口区域剪切应力分布均匀,大小接近平均剪应力;正应力在边缘有应力集中,中央应力约为平均正应力的77%.由于纤维增强陶瓷基复合材料存在微弱缺口敏感性,Arcan圆盘测出的强度略低于均匀拉伸结果.采用系数对测出的强度进行了修正.     

Strength of polybenzimidazole and phenolic laminate-to-metal joints

Stress concentration effects and strengths of bonded and bolted butt joints were investigated for a glass fabric polybenzimidazole lalminate at room temperatuer and 700°F for a gloass fabric phenolic laminate at room temperature and 500°F. Specimen configurations included: (1) standard tensile specimen, (2) stress concentration specimen, (3) bolted double shear butt joint, (4) bolted single shear butt joint, (5) bonded double shear butt joint and (6) bonded single shear butt joint. Both polybenzimidazole and phenolic laminates exhibited high room temperature tensile strengths and little degradation of that strength occured as a result of elevated temperature exposure. However, low joint effencies (22 to 32%) were obtained for bolted butt joint specimens. Although bonded joints exhibited higher efficiencies, they suffered from a thermal expansion mismatch between the plastic laminate and the Inconel butt plates.     

Failure analysis of 2D C/SiC composite z-pinned/bonded hybrid single-lap joints

Z-pinned/bonded hybrid joints are widely used in the 2D C/SiC composite structures, whose mechanical behavior and failure mechanisms are directly related with the structure integrity. The hybrid joints for 2D C/SiC composite structures are formed by depositing SiC into the gap of z-pinned joints. To evaluate the SiC bonding effect, the tensile experiments for two kinds of z-pinned joints with and without bonded layer were conducted. It was proved that the failure modes of the pin were the tensile and shear failure, and the bonded layer was the interlaminar shear failure of the substrate plate instead of the shear failure of SiC bonded layer due to the smaller interlaminar shear strength. The bonded zone states of specimens were also examined, which were reproduced in the shell-fastener numerical model with surface-based cohesive behavior. Combining with shear strength theory, a numerical model is developed to study the failure processes of the hybrid joints. The SiC bonded zone areas can also greatly influence the failure response of the hybrid joints. The large SiC bonded layer zone can improve the shear strength of the joints. The failure of the joints is determined by the SiC bonded layer when the SiC bonded zone is large enough. This study can be helpful to evaluate and design the SiC bonded zone states of the hybrid joints in the engineering application.     

Effect of adherend's rigidity on the shear strength of single lap adhesive joints

The present paper compares the tensile shear strength of single-lap joints with different adherends. Three materials were combined in the single lap joints: a carbon/epoxy laminated composite, a high elastic limit steel and the 6082-T6 aluminium alloy. The shear strength of joints was influenced by the adherend stiffness and the highest shear strengths were obtained using high stiffness adherend materials. The overlap length influenced the shear strength in different ways depending on the adherend materials. Numerical analysis concluded that the increase in the rigidity of the adherends decreases the rotation of the specimen and promotes a more uniform distribution of stresses in the glue. In joints with distinct materials, the less stiff material was found to determine the strength of the appropriate joint.     

The Interfacial Bond Strength in Glass Fibre-Polyester Resin Composite Systems

The interfacial bond strength in glass fibre-polyester resin composites has been investigated using various experimental techniques. These included blocks of resin containing fibre (in which, depending on the geometry of the specimen, failure occurs in either a shear or tensile mode) the pullout of a fibre from a disc of resin and a short beam shear test for interlaminar shear strength determination.

Low power optical microscopy and optical retardation measurements of stress induced birefringence were used to detect the difference between intact and debonded fibre resin interfaces. The shear modulus and shear strength of the resin were obtained from torsion tests on cylindrical rods of the resin.

The single fibre shear debonding specimen and the short beam shear test are shown to be the most viable test methods but interpretation of the results is complicated by the various modes of failure possible and by the different stress states which exist in the area of the specimen where debonding starts. Stress concentration factors obtained by finite element analysis and photoelastic analysis have been applied to the results from these tests and the corrected interfacial bond strengths are in close agreement.

The real interfacial bond strengths of well bonded glass-fibre polyester resin systems is shown to be of the order of 70 MN m^-2.     

Bond durability of wood-glue joints on Kapur (Dryobalanops spp.) and Yellow Seraya (Shorea spp.) bonded with phenol-formaldehyde resin adhesive

Bond durability of wood-glue joints on Kapur (Dryobalanops spp.) and Yellow Seraya (Shorea spp.) bonded with phenol formaldehyde resin was investigated. The tensile shear strength of wood-glue joints bonded and tested thirteen years ago were compared with samples tested after thirteen years conditioning. The effect of treating wood (boiling for two to thirtytwo hours) on the tensile shear strength of the wood-glue joint was also taken into consideration. The tensile shear strength of Kapur and Yellow Seraya treated for 20–24 and 15–20 h, respectively, before gluing was higher than that of the untreated samples which were bonded and tested thirteen years ago. The retention ratio of tensile shear strength of Kapur after 13 years was lowest at 20–24 h boiling. Likewise, results for specimens similarly tested showed the same pattern for both dry and wet conditions. However, variation of boiling time on the solid wood of both raw materials did not affect their ratios of decrease in tensile shear strength. Bond durability of Yellow Seraya wood-glue joints was higher thanthat for Kapur wood-glue joints as indicated by the higher retention ratio of the tensile shear strength of the former compared with the latter.     

Effect of Flaws in the Adhering Interface on the Strength of Adhesive-bonded Butt Joints

This paper presents the strength of metal-to-metal bonded joints with a flaw in the interface between the adhesive layer and the adhering surface of adherend. The test specimens of butt joints are prepared by bonding two thin-wall metal tubes. The materials are carbon steel, aluminum alloy, brass and copper. The adhesive is epoxy resin. The tensile and shear strength of the joints are experimentally determined by subjecting the specimens to axial load and torsion for various flaw sizes and thickness of adhesive layers. Linear elastic fracture mechanics is applied to the experimental results. The stress intensity factors for a layered composite with a flaw in the interface are numerically calculated in terms of flaw size and loading by using Erdogan's formulas. The fracture stresses of joints with a flaw are predicted at the critical values of the stress intensity factors. The strength of joints without a flaw is also correlated with the stress intensity factors by use of a concept of “effective flaw size”.     

Comparison of fracture behavior between acrylic and epoxy adhesives

An experimental study was conducted on the strength of adhesively bonded steel joints, prepared epoxy and acrylic adhesives. At first, to obtain strength characteristics of these adhesives under uniform stress distributions in the adhesive layer, tensile tests for butt, scarf and torsional test for butt joints with thin-wall tube were conducted. Based on the above strength data, the fracture envelope in the normal stress-shear stress plane for the acrylic adhesive was compared with that for the epoxy adhesive. Furthermore, for the epoxy and acrylic adhesives, the effect of stress triaxiality parameter on the failure stress was also investigated. From those comparison, it was found that the effect of stress tri-axiality in the adhesive layer on the joint strength with the epoxy adhesive differed from that with the acrylic adhesive. Fracture toughness tests were then conducted under mode l loading using double cantilever beam (DCB) specimens with the epoxy and acrylic adhesives. The results of the fracture toughness tests revealed continuous crack propagation for the acrylic adhesive, whereas stick-slip type propagation for the epoxy one. Finally, lap shear tests were conducted using lap joints bonded by the epoxy and acrylic adhesives with several lap lengths. The results of the lap shear tests indicated that the shear strength with the epoxy adhesive rapidly decreases with increasing lap length, whereas the shear strength with the acrylic adhesive decreases gently with increasing the lap length.     

The effect of adhesive thickness on tensile and shear strength of polyimide adhesive

The effect of adhesive thickness on tensile and shear strength of a polyimide adhesive has been investigated. Tensile and shear tests were carried out using butt and single lap joints. Commercially available polyimide (Skybond 703) was used as adhesive and aluminum alloy (5052-H34) was used as adherends. The tensile strength of the butt joints decreased with increasing adhesive thickness. In contrast, adhesive thickness did not seem to affect the shear strength of single lap joints. The fabricated joints using the polyimide adhesive failed in an interfacial manner regardless of adhesive thickness. The linear elastic stress analysis using a finite element method (FEM) indicates that the normal stress concentrated at the interface between the adherend and the adhesive. The FEM analysis considering the interfacial stress well explains the effect of adhesive thickness on the joint strength.