Preparation of polyimide/siloxane‐functionalized graphene oxide composite films with high mechanical properties and thermal stability via in situ polymerization

An effective approach to prepare polyimide/siloxane‐functionalized graphene oxide composite films is reported. The siloxane‐functionalized graphene oxide was obtained by treating graphene oxide (GO) with 1,3‐bis(3‐aminopropyl)‐1,1,3,3‐tetra‐methyldisiloxane (DSX) to obtain DSX‐GO nanosheets, which provided a starting platform for in situ fabrication of the composites by grafting polyimide (PI) chains at the reactive sites of functional DSX‐GO nanosheets. DSX‐GO bonded with the PI matrix through amide linkage to form PI‐DSX‐GO films, in which DSX‐GO exhibited excellent dispersibility and compatibility. It is demonstrated that the obvious reinforcing effect of GO to PI in mechanical properties and thermal stability for PI‐DSX‐GO is obtained. The tensile strength of a composite film containing 1.0 wt% DSX‐GO was 2.8 times greater than that of neat PI films, and Young's modulus was 6.3 times than that of neat PI films. Furthermore, the decomposition temperature of the composite for 5% weight loss was approximately 30 °C higher than that of neat PI films. © 2015 Society of Chemical Industry     

Highly flexible and thermal conductive films of graphene/poly(naphthylamine) and applications in thermal management of LED devices

In 5G era, integration and miniaturization of electronic components lead to increasing challenges in thermal management. Materials with high thermal conductivity and flexibility are strongly desired for dissipating heat locally generated in such devices. Due to its extraordinary thermal conducting performance, graphene has been exhibiting great potential in thermal management. In this work, composite films based on graphene oxide and poly-naphthylamine (gGO/PNA) with enhanced thermal conducting performance have been achieved by employing poly (naphthylamine) (PNA) as repairing additives to restore topological defects of graphene oxide (GO). Specifically, gGO/PNA films are prepared with a facile operation of vacuum filtration followed by an elevated temperature treatment. The optimal thermal conductivity (κ) of gGO/PNA reaches to 1016.03 W m⁻¹ K⁻¹, 31.3% enhancement over that of the pristine graphene one. The thermal conducting performance test demonstrates the film an efficient heat-dissipation ability from a heat-generating LED bulb. Furthermore, the film exhibits excellent flexibility, making it survival from a 1000-cycle bending test. This finding may promote the development of heat-spreading materials and their applications in thermal management of highly integrated electronics.     

Thin polymer films based on poly(vinyl alcohol) containing graphene oxide and reduced graphene oxide with functional properties

In this article, the effect of the addition of graphene oxide (GO) and reduced graphene oxide (rGO) on the mechanical properties, thermal stability, and electrical conductivity of polyvinyl alcohol (PVA) has been investigated. Different weight percentages of nanofillers ranging from 0.5 to 5 wt% have been combined with PVA. The ultrasonic technique has been applied to disperse nanofillers in the PVA solution. The nanocomposite films have been prepared via solution casting technique and the dispersion of nanofillers into the PVA has been studied through optical microscopy. The microstructure, crystallization behavior, and interfacial interaction were characterized through X-ray diffraction and Fourier transform infrared spectroscopy. Differential scanning calorimetry (DSC) and thermogravimetric analysis have been applied to study the thermal properties of the prepared nanocomposites. The DSC results revealed that the crystallization temperature and melting temperature were enhanced in the presence of GO nanofiller. Besides, the tensile strength at break was improved along with the addition of GO; however, elongation at break for PVA/GO and PVA/rGO was diminished. Moreover, all specimens showed insulating behavior and the only sample was electrically conducting, which contain a high amount of rGO (5 wt%).     

氧化石墨烯/聚偏氟乙烯复合膜研究

采用Hummers法合成氧化石墨,通过超声分散法获得氧化石墨烯,并使用溶剂蒸发法制备了氧化石墨烯/聚偏氟乙烯复合膜。采用透射电子显微镜(TEM)、红外光谱(FTIR)以及X射线衍射(XRD)对氧化石墨烯的形貌和结构进行分析,对复合膜进行扫描电子显微镜(SEM)、机械性能以及导热系数的分析测定。结果表明,本实验中制备的氧化石墨烯含有大量的含氧基团;氧化石墨烯能够均匀的分散在复合膜中,并且会增加复合膜的机械性能和导热性能。复合膜的导热系数随w(氧化石墨烯)的增加而呈现先增大后减小的趋势,当w(氧化石墨烯)为0.4%时,导热系数达到最大值。     

Multifunctional polyimide/graphene oxide composites via in situ polymerization

In this article, we detail an effective way to improve electrical, thermal, and gas barrier properties using a simple processing method for polymer composites. Graphene oxide (GO) prepared with graphite using a modified Hummers method was used as a nanofiller for r‐GO/PI composites by in situ polymerization. PI composites with different loadings of GO were prepared by the thermal imidization of polyamic acid (PAA)/GO. This method greatly improved the electrical properties of the r‐GO/PI composites compared with pure PI due to the electrical percolation networks of reduced graphene oxide within the films. The conductivity of r‐GO/PI composites (30:70 w/w) equaled 1.1 × 10¹ S m^?1, roughly 10¹⁴ times that of pure PI and the oxygen transmission rate (OTR, 30:70 w/w) was reduced by about 93%. The Young's modulus of the r‐GO/PI composite film containing 30 wt % GO increased to 4.2 GPa, which was an approximate improvement of 282% compared with pure PI film. The corresponding strength and the elongation at break decreased to 70.0 MPa and 2.2%, respectively. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40177.     

Effects of crosslinking agents on the physical properties of polyimide/amino‐functionalized graphene oxide hybrid films

The effects of crosslinking agents (crosslinkers) on polyimide (PI)/graphene oxide (GO) hybrid films were extensively investigated. The surface of GO was modified with amino groups using 4‐aminobenzylamine to improve compatibility with pyromellitic dianhydride/4,4′‐oxydianiline PI, and two kinds of crosslinkers were used: tris(4‐aminophenyl)amine and 1,3,5‐triazine‐2,4,6‐triamine (melamine). The mechanical, thermal and optical properties of the PI hybrid films were investigated. In particular, the transparency and physical properties of the PI hybrid films containing amino‐functionalized GO with homogeneous dispersion were improved. As the content of the crosslinker increased, a crosslinking network was formed between the PI chains, and the stiffness of the hybrid films was increased. The glass transition temperature, heat resistance and mechanical properties were also enhanced. The PI hybrids prepared with a rigid crosslinker exhibited higher optical transparency due to the reduction of the intermolecular charge transfer interactions with increasing interchain spacing between the PI chains. © 2018 Society of Chemical Industry     

聚偏氟乙烯/石墨烯复合材料的制备及性能研究

用溶液共混法制备出聚偏氟乙烯/氧化石墨烯复合材料(PVDF/GO),经高温热压将GO还原得到聚偏氟乙烯/还原氧化石墨烯复合材料(PVDF/rGO)。研究了填料种类及含量对复合材料电学性能、热稳定性和力学性能的影响。结果表明：随GO和rGO的添加,两种复合材料的介电常数(ε _r)均变大、介电损耗(tanδ)变化不大;低含量下GO和rGO均能提高PVDF的热稳定性,但rGO对PVDF性能的改善效果更好;随填料含量从0增加到8%(质量),100 Hz下PVDF/rGO复合材料的ε _r从3.60增加到38.30,PVDF/rGO[4%(质量)]复合材料失重率为5%的分解温度较纯PVDF提高了6.44℃。rGO增强了PVDF的刚性,PVDF/rGO复合材料的拉伸强度先增大后减小,杨氏模量逐渐增大,当rGO含量为4%(质量)时拉伸强度最大,拉伸强度和弹性模量分别较纯PVDF提高了35.30%、22.58%。但GO和rGO都降低了复合材料的击穿场强。     

Synthesis of manganese (IV) oxide at activated carbon on reduced graphene oxide sheets via laser irradiation technique for organic binder-free electrodes in flexible supercapacitors

We report a novel, green, scalable technique to synthesize binder-free, high-purity conductive composite comprising activated carbon (AC), manganese dioxide nanorods (MnO₂), and reduced graphene oxide sheets (rGO) for flexible supercapacitors with outstanding electrochemical performance. UV pulsed laser irradiation of GO-based composite dispersion (AC/GO or MnO₂@AC/GO) in ethanol aqueous medium was used to induce a photocatalytic reduction of GO and simultaneous anchor AC particles or AC loaded MnO₂ nanorods (MnO₂@AC) on the reduced GO sheets (rGO) at room temperature and atmospheric pressure. rGO sheets serve as a large surface area, conductive binder to enhance the ion adsorption, electrical conductivity, and mechanical flexibility of supercapacitor electrodes. This laser-induced photocatalytic reduction method was used to prepare two different rGO-based colloidal composites AC/rGO (CG) and MnO₂@AC/rGO (MCG). The prepared rGO-based colloidal composites were used to fabricate symmetric supercapacitors (CG//CG and MCG//MCG) and asymmetric supercapacitors (MCG//CG) in which MCG is the positive electrode and CG is the negative one. All prepared rGO-based supercapacitors demonstrated significant improvement in their electrochemical performance compared with rGO-free AC based supercapacitors. The enhancement in the electrochemical properties of rGO-based supercapacitors could be attributed to the intrinsic characteristics of rGO, such as high surface area, excellent electrical conductivity, and super mechanical flexibility. Our approach is a one-step, scalable, cost-effective synthesis technique to produce all binder-free AC/rGO based composites for flexible energy-storage devices.     

Preparation of functional reduced graphene oxide and its influence on the properties of polyimide composites

Homogeneous dispersion and strong filler–matrix interfacial interactions were vital factors for graphene for enhancing the properties of polymer composites. To improve the dispersion of graphene in the polymer matrix and enhance the interfacial interactions, graphene oxide (GO), as an important precursor of graphene, was functionalized with amine‐terminated poly(ethylene glycol) (PEG–NH₂) to prepare GO–poly(ethylene glycol) (PEG). Then, GO–PEG was further reduced to prepare modified reduced graphene oxide (rGO)–PEG with N₂H₄·H₂O. The success of the modification was confirmed by Fourier transform infrared spectroscopy, thermogravimetric analysis, and Raman spectroscopy. Different loadings of rGO–PEG were introduced into polyimide (PI) to produce composites via in situ polymerization and a thermal reduction process. The modification of PEG–NH₂ on the surface of rGO inhibited its reaggregation and improved the filler–matrix interfacial interactions. The properties of the composites were enhanced by the incorporation of rGO–PEG. With the addition of 1.0 wt % rGO–PEG, the tensile strength of PI increased by 81.5%, and the electrical conductivity increased by eight orders of magnitude. This significant improvement was attributed to the homogeneous dispersion of rGO–PEG and its strong filler–matrix interfacial interactions. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45119.     

Stretchable conductive films based on carbon nanomaterials prepared by spray coating

Stretchable conductive films consisting of a layer of carbon nanomaterials, that is, carbon nanotubes (CNTs), mechanically exfoliated graphene (GE), or chemically reduced graphene oxide (rGO), deposited on polydimethylsiloxane (PDMS) films were prepared by spray coating. The correlations among the concentration of the carbon nanomaterials, the electrical resistance and the optical transmittance of the spray‐coated films were investigated. The results show that the conductivity of the CNT coatings was better than that of the GE‐based coatings. When the CNT concentration of the dispersion for spraying increased from 0.01 to 0.075 mg/mL, the surface electrical resistance decreased from 7.8 × 10³ to 6.7 × 10² Ω, whereas for the GE or rGO coatings, the electrical resistance was several orders higher than that of the CNT coatings. The CNT spray‐coated films exhibited an optical transmittance of about 60% at a wavelength of 550 nm; this was higher than that of the GE or rGO spray‐coated films. The electric heating behaviors of the stretchable conductive films as functions of the applied voltage and the concentration of carbon nanomaterials and the electrical conductivity under tensile and bending strains were also investigated. The surface temperature of the CNT‐coated films rose rapidly up to 200°C within about 40 s when the applied voltage was 110 V. The stretchable conductive films have potential as electric heating elements because of their excellent conductive properties. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43243.     

Preparation and properties of bacterial cellulose/graphene oxide composite films using dyeing method

In this study, bacterial cellulose (BC) hydrogels were cultured from a kombucha SCOBY starter. The scanning electron microscopy (SEM) results indicated that the dried BC exhibited an interpenetrating fibrous mat. The BC films harvested for 5, 10, and 15 days were 15–19, 14.4–24, and 30–31 μm thick, respectively. Then, BC/graphene oxide (GO) composite films were prepared via the exhaust dyeing method. GO sheets penetrated the BC matrix, resulting in the formation of a BC/GO composite, as revealed by the SEM analysis results. The mechanical properties of the composite films were investigated. Compared with virgin BC, the tensile strength of the composite films was higher, while the %E at break was lower, resulting in a significant increase in the Young's modulus. The X-ray diffraction results indicated that an increase in the dyeing time (0.5–2 h) gradually induced cellulose crystalline conformation, which in turn affected the swelling ability, mechanical properties, and electrical properties of the BC/GO composite films. After the reduction of GO to reduced GO (rGO), flexible conductive BC/rGO films were obtained, as confirmed by their resistivity values. Thus, flexible conductive composite films with excellent mechanical properties were successfully fabricated.     

Preparation of well‐dispersed reduced graphene oxide and its mechanical reinforcement in polyvinyl alcohol fibre

The current work reports the preparation and characterization of polyvinyl alcohol (PVA) composite fibres reinforced with graphene reduced from graphene oxide (GO) by using oligomeric proanthocyanidin (OPC) as a reductant. After reduction, most of the oxygen‐containing groups were removed from the GO and reduced graphene oxide (rGO) was prepared. As a result of combined OPC as a dispersant, rGO could be well dispersed in a dimethyl sulfoxide/H₂O mixed solvent and in PVA matrix, and the PVA/rGO dispersion was wet spun followed by hot drawing to prepare continuous PVA/rGO composite fibres. The PVA/rGO composite fibres exhibited a significant enhancement of mechanical properties at low rGO loadings; in particular the tensile strength and Young's modulus of the 2.0 wt% rGO and PVA composite fibre increased to 244% and 294% respectively relative to neat PVA fibre. Moreover, the storage modulus (?10 °C) and T_g increased to 300% and 7.2 °C, respectively. © 2016 Society of Chemical Industry     

In situ polymerization of polyimide‐based nanocomposites via covalent incorporation of functionalized graphene nanosheets for enhancing mechanical,thermal, and electrical properties

In this study, we report an effective method to fabricate high‐performance polyimide (PI)‐based nanocomposites using 3‐aminopropyltriethoxysilane functionalized graphene oxide (APTSi‐GO) as the reinforcing filler. APTSi‐GO nanosheets exhibit good dispersibility and compatibility with the polymer matrix because of the strong interfacial covalent interactions. PI‐based nanocomposites with different loadings of functionalized graphene nanosheets (FGNS) were prepared by in situ polymerization and thermal imidization. The mechanical performance, thermal stability, and electrical conductivity of the FGNS/PI nanocomposites are significantly improved compared with those of pure PI by adding only a small amount of FGNS. For example, a 79% improvement in the tensile strength and a 132% increase in the tensile modulus are achieved by adding 1.5 wt % FGNS. The electrical and thermal conductivities of 1.5 wt % FGNS/PI are 2.6 × 10^?3 S/m and 0.321 W/m·K, respectively, which are ～10¹⁰ and two times higher than those of pure PI. Furthermore, the incorporation of graphene significantly improves the glass‐transition temperature and thermal stability. The success of this approach provides a good rationale for developing multifunctional and high‐performance PI‐based composite materials. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42724.     

Synergistic effects of boron nitride sheets and reduced graphene oxide on reinforcing the thermal conduction,SERS performance and thermal property of polyimide composite films

Polyimide (PI) composite films with hybrid fillers containing hBN (hexagonal boron nitride) sheets and rGO (reduced graphene oxide) were successfully fabricated by in-situ polymerization. Herein, hBN sheets and rGO were obtained by ball milling and chemical reduction, respectively. In PI composite films, hBN can be tightly attached onto the surface of rGO via π-π interaction, which can benefit the construction of heat-conduction pathways and reduce boundary of heat resistance. The results show that the addition of rGO and hBN could enhance the thermal conductivity by synergistic effects. Specially, hBN and rGO are at the weight ratio of 1:1 and at the total loading of 33 wt%, thermal conductivity of PI composites can reach up to 1.19 Wm⁻¹ K⁻¹, which is 5.61 times higher than that of pure PI. Thermal property and dynamic mechanical property of composite films were also investigated. Besides, compared with pure PI, mixed fillers have obvious surface-enhanced Raman scattering signals, indicating the synergistic effect of the mixed fillers. Overall, this study gives insights into heat dissipative and high sensitivity analysis components which may be used in the field of high-temperature micro fabrication.     

Effect of oxygen functional groups of reduced graphene oxide on the mechanical and thermal properties of polypropylene nanocomposites

Reduced graphene oxide (rGO) with various surface structures was prepared by reducing graphene oxide (GO) with hydrazine hydrate (N₂H₄), sodium borohydride (NaBH₄) and l ‐ascorbic acid, respectively. The resulting rGO were used to fabricate rGO/polypropylene (PP) nanocomposites by a melt‐blending method. The surface structure of rGO as well as multifunctional properties of rGO/PP nanocomposites were thoroughly investigated. It was shown that rGO with highest C/O ratio could be obtained by reducing GO with N₂H₄. The crystallization behaviors, tensile strength, thermal conductivity and thermal stability of rGO/PP nanocomposites were significantly improved with the increase of C/O ratio of rGO. For example, with only 1 phr (parts per hundred PP) rGO reduced by N₂H₄, the degree of crystallinity, tensile strength, maximum heat decomposition temperature and thermal conductivity of PP nanocomposite were increased by 6.2%, 20.5%, 48.0 °C and 54.5%, respectively, compared with those of pure PP. Moreover, the thermal degradation kinetics indicated that the decomposition activation energy of rGO/PP nanocomposites could be enhanced by adding rGO with higher C/O ratio. © 2018 Society of Chemical Industry     

A facile one step electrostatically driven electrocodeposition of polyviologen–reduced graphene oxide nanocomposite films for enhanced electrochromic performance

Polyviologen (PV)–reduced graphene oxide (rGO) nanocomposite films were fabricated by simple, one-step reductive electropolymerization of cyanopyridinium based precursor monomer (CNP) in an aqueous dispersion of graphene oxide (GO). Since the polymer formation and reduction of graphene oxide occurs within the same potential window, electrocodeposition method was preferred for obtaining nanostructured PV–rGO films. Cyclic voltammetry experiments of PV–rGO displayed two well resolved, reversible one-electron redox processes typical of viologen. Being a redox polymer, incorporation of rGO further enhances the electroactivity of the PV in the composite films. Vibrational spectral analysis with surface characterization revealed structural changes after composite formation along with subsequent reduction of GO within the polymer matrix. The PV–rGO nanostructured film exhibits a high-contrast electrochromism with low driving voltage induced striking color changes from transparent (0 V) to purple (−0.6 V), high coloration efficiency, fast response times and better cycling stability compared to a pristine PV film. This improved performance can be attributed to the high stability of the electrochrome in the composite assembly induced by electrostatically driven non-covalent interactions between redox PV²⁺ and negatively charged rGO, improved electrical conductivity and enlarged surface area accessed through reinforced nanostructured graphene sheets for tethering PV molecules.     

Study on thermal properties of stearyl alcohol modified graphene oxide/ n-octadecane composite phase change materials

Adding high thermal conductivity fillers to n-octadecane to form a composite phase change material(PCM) can improve its thermal conductivity. At the same time, to ensure high thermal conductivity, dispersion stability and recycling reliability of PCM, a type of composite PCM has been fabricated by grafting stearic alcohol onto graphene oxide (GO). The modified graphene/n-octadecane composite PCMs with 0, 1%, 2%, 3% and 4%(mass) of modified graphene were prepared to characterize and study of feature structure and thermophysical properties by means of scanning electron microscope, infrared spectrum analysis, differential scanning calorimetry and thermal conductivity analysis, etc. Experiments show that the modified graphene/n-octadecane composite PCMs prepared in this paper has good dispersion stability. When the mass fraction of modified graphene reaches 4%, the thermal conductivity of composite PCMs is 131.9% higher than that of pure n-octadecane.     

硬脂醇改性的氧化石墨烯/正十八烷复合相变材料的热物性研究

向正十八烷中加入高导热填充物形成复合相变材料(PCM),可以很好地提升其导热性能,同时,为了保证符合相变材料的高热导率、分散性和再循环可靠性,利用硬脂醇修饰氧化石墨烯(GO),形成改性石墨烯(MG)与正十八烷的复合相变材料。分别制备了改性石墨烯质量分数为0、1%、2%、3%、4%(质量)的改性石墨烯/正十八烷复合相变材料,并经过扫描电镜测试、红外光谱分析、差示扫描量热实验及导热分析等测试对其形貌结构及热物性进行表征和研究。实验表明制备的改性石墨烯/正十八烷复合相变材料具有很好的分散性;当纳米石墨烯片的质量分数达到4%时,复合相变材料的热导率相对于纯正十八烷高出了131.9%。     

Enhanced thermal conductivity and dimensional stability of flexible polyimide nanocomposite film by addition of functionalized graphene oxide

Polyimide (PI) nanocomposites with both enhanced thermal conductivity and dimensional stability were achieved by incorporating glycidyl methacrylate‐grafted graphene oxide (g‐GO) in the PI matrix. The PI/g‐GO nanocomposites exhibited linear enhancement in thermal conductivity when the amount of incorporated g‐GO was less than 10 wt%. With the addition of 10 wt% of g‐GO to PI (PI/g‐GO‐10), the thermal conductivity increased to 0.81 W m^?1 K^?1 compared to 0.13 W m^?1 K^?1 for pure PI. Moreover, the PI/g‐GO‐10 composite exhibited a low coefficient of thermal expansion (CTE) of 29 ppm °C^?1. The values of CTE and thermal conductivity continuously decreased and increased, respectively, as the g‐GO content increased to 20 wt%. Combined with excellent thermal stability and high mechanical strength, the highly thermally conducting PI/g‐GO‐10 nanocomposite is a potential substrate material for modern flexible printed circuits requiring efficient heat transfer capability.     

Influence of curing temperature on properties of the polyacrylonitrile/polyimide composite films

A series of polyacrylonitrile/polyimide (PAN/PI) composite films with different PAN contents are prepared under given curing temperatures (250, 300, 350, and 400°C). The microstructure of the composite films is observed by SEM, and the thermal, dielectric and mechanical properties of the composite films are determined. The results show that the self‐assembly behavior of polyamic acid gives rise to connected network structure in the composite films and the variations in the microstructure of the composite films cured at different temperatures show important effects on the properties of PAN/PI composite films. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40283.