Pt/Pt-Ce/γ-Al2O3催化氧化甲苯研究

通过等体积浸渍法制备单贵金属Pt/γ-Al₂O₃和双金属Pt-Ce/γ-Al₂O₃催化剂,考察Ce对催化剂活性的影响,确定催化剂最优配比。结果表明,当Pt的负载量为质量分数0.5%时,Pt/γ-Al₂O₃催化活性最高;当Pt的负载量为质量分数0.2%,Ce的负载量为质量分数1.0%时,Pt-Ce/γ-Al₂O₃催化剂的催化活性最高。Pt-Ce/γ-Al₂O₃催化剂的甲苯转化率高于Pt/γ-Al₂O₃催化剂。随着Pt负载量增大,催化剂孔容、孔径减小。粉体式催化剂性能优于整体式催化剂,但差别不大;Ce的添加有助于催化剂活性的提升。     

Performance and characterization of Ru/Al2O3 and Ru/SiO2 catalysts modified with Mn for Fischer–Tropsch synthesis

Mn effect and characterization on γ-Al₂O₃-, -Al₂O₃- and SiO₂-supported Ru catalysts were investigated for Fischer–Tropsch synthesis under pressurized conditions. In the slurry phase Fischer–Tropsch reaction, γ-Al₂O₃ catalysts showed higher performance on CO conversion and C₅⁺ selectivity than -Al₂O₃ and SiO₂ catalysts. Moreover, Ru/Mn/γ-Al₂O₃ exhibited high resistance to catalyst deactivation and other catalysts were deactivated during the reaction. From characterization results on XRD, TPR, TEM, XPS and pore distribution, Ru particles were clearly observed over the catalysts, and γ-Al₂O₃ catalysts showed a moderate pore and particle size such as 8 nm, where -Al₂O₃ and SiO₂ showed highly dispersed ruthenium particles. The addition of Mn to γ-Al₂O₃ enhanced the removal of chloride from RuCl₃, which can lead to the formation of metallic Ru with moderate particle size, which would be an active site for Fischer–Tropsch reaction. Concomitantly, manganese chloride is formed. These schemes can be assigned to the stable nature of Ru/Mn/γ-Al₂O₃ catalyst.     

Preparation and characterization of novel porous metal/ceramic catalytic membrane materials

In order to obtain improved separation or catalytic activity, we propose a method to modify the surface of porous ceramic membranes by modifying the surface of sol particles. The key technical difficulty of this method is how to get appropriate ligands which can make metal ions adsorb on sol particles in the appropriate pH range in which the sol maintains its dynamic stability. Pd/γ-A1₂O₃ catalytic membrane materials with mesopore and a narrow pore size distribution were prepared by this method. Other kinds of metal/ceramic catalytic membrane materials such as Ni/γ-Al₂O₃, Pt/γ-Al₂O₃ can also be obtained by the same method.     

CO气相偶联合成草酸二甲酯Pd/α-Al2O3催化剂失活与再利用

作为合成气制乙二醇关键步骤之一,CO与亚硝酸甲酯合成草酸二甲酯备受关注。综述了近年来CO气相偶联合成草酸二甲酯Pd/α-Al₂O₃催化剂失活与再利用研究进展,探讨催化剂再利用工艺存在的问题,指出应根据在工业应用中出现的问题对Pd/α-Al₂O₃催化剂进行失活研究,在此基础上开发针对性的再生工艺;钯催化剂回收方面萃取法和吸附法逐渐成为研究重点,高效、低耗、短流程绿色工艺的开发是失活钯催化剂再利用的发展方向。     

Synthesis and catalytic properties of Ce0.6Zr0.4O2 solid solutions in the oxidation of soluble organic fraction from diesel engines

Ce_0.6Zr_0.4O₂ solid solutions were synthesized by co-precipitation, sol–gel like method, solution combustion and surfactant-assistant approaches, respectively. The catalytic properties of bulk and γ-Al₂O₃ supported Ce_0.6Zr_0.4O₂ solid solutions were studied for the oxidation of soluble organic fractions (SOF) from diesel engines by TG-DTA method. The physicochemical properties were characterized by XRD, BET surface area and pore distribution, SEM, TEM, and particle size distribution techniques. XRD and TEM results show that a Ce_0.6Zr_0.4O₂ solid solution was formed for samples as-prepared and heat-treated at 900 °C for 2 h in air. The co-precipitation derived Ce_0.6Zr_0.4O₂ has as high BET surface area as 153.71 m²/g by controlling preparation conditions. Notable is that the surface area and particle size for fresh Ce_0.6Zr_0.4O₂ ignited at 350 °C decreased little after a thermal treatment in air at 900 °C for 2 h. Furthermore, its bulk density is lowest. The commercial engine oil (SJ5W/40) for FAW-VOLKSWAGEN, which was used by Bora 1.9 TDI diesel cars in China market was substituted for SOF. The catalytic activity was evaluated by normalized peak areas and extrapolated onset temperatures of DTA curves. A computer program was developed by direct non-linear regression model for simulation of TG/DTG curves to determine the thermal processes and kinetic parameters. It is found that lube evaporation/decomposition and thermal decomposition (pyrolysis) were observed under a nitrogen atmosphere. Lube evaporation fractions were inhibited by Ce_0.6Zr_0.4O₂ and γ-Al₂O₃. While under an air atmosphere, namely, in the process of lube oxidation (combustion), evaporation/decomposition, low-temperature oxidation and high-temperature oxidation were distinguished. Ce_0.6Zr_0.4O₂ solid solutions are active catalysts for lube oxidation, in which the sample prepared by solution combustion has the highest activity, mainly due to the maintenance of the surface area and particle size upon sintering and its lowest bulk density. However, γ-Al₂O₃ is more like a support. There exists synergism between Ce_0.6Zr_0.4O₂ and γ-Al₂O₃: γ-Al₂O₃ adsorbs lube retaining it within its pore structure, whereas, Ce_0.6Zr_0.4O₂ solid solutions initiate oxidation reactions when light-off temperatures reach. The application of CeO₂-ZrO₂ solid solution prepared by solution combustion at lower temperature would be promising in diesel oxidation catalysts.     

Effect of phosphorus addition on the hydrotreating activity of NiMo/Al2O3 carbide catalyst

A series of phosphorus promoted γ-Al₂O₃ supported NiMo carbide catalysts with 0–4.5 wt.% P, 13 wt.% Mo and 2.5 wt.% Ni were synthesized and characterized by elemental analysis, pulsed CO chemisorption, BET surface area measurement, X-ray diffraction, near-edge X-ray absorption fine structure, DRIFT spectroscopy of CO adsorption and H₂ temperature programmed reduction. X-ray diffraction patterns and CO uptake showed the P addition to NiMo/γ-Al₂O₃ carbide, increased the dispersion of β-Mo₂C particles. DRIFT spectra of adsorbed CO revealed that P addition to NiMo/γ-Al₂O₃ carbide catalyst not only increases the dispersion of Ni-Mo carbide phase, but also changes the nature of surface active sites. The hydrodenitrogenation (HDN) and hydrodesulfurization (HDS) activities of these P promoted NiMo/γ-Al₂O₃ carbide catalysts were performed in trickle bed reactor using light gas oil (LGO) derived from Athabasca bitumen and model feed containing quinoline and dibenzothiophene at industrial conditions. The P added NiMo/γ-Al₂O₃ carbide catalysts showed enhanced HDN activity compared to the NiMo/γ-Al₂O₃ catalysts with both the feed stocks. The P had almost no influence on the HDS activity of NiMo/γ-Al₂O₃ carbide with LGO and dibenzothiophene. P addition to NiMo/γ-Al₂O₃ carbide accelerated CN bond breaking and thus increased the HDN activity.     

Deactivation studies over NiO/γ-Al2O3 catalysts for partial oxidation of methane to syngas

Two types of NiO/γ-Al₂O₃ catalysts prepared by the impregnation and the sol–gel method were used for the partial oxidation of methane to syngas at 850°C (GHSV1.8×10⁵ lkg⁻¹ h⁻¹). The effects of the carbon deposition, the loss and sintering of nickel and the phase transformation of γ-Al₂O₃ support on the catalytic performance during 80 h POM reaction were investigated with a series of characterization such as XRD, BET, AAS, TG, and XPS. The results indicated that the carbon deposition and the loss and sintering of nickel could not cause the serious decrease of catalytic performance over NiO/γ-Al₂O₃ catalyst during the short-time reaction. However, the slow process of the support γ-Al₂O₃ phase transforming into -Al₂O₃ could slowly decrease the performance of NiO/γ-Al₂O₃ catalysts. Aimed at the reasons of the deactivation, an improved catalyst was obtained by the complexing agent-assisted sol–gel method.     

η-Al2O3与γ-Al2O3在CS2催化水解反应中的性能比较

通过制备高纯度的前驱体湃铝石获得了η-Al₂O₃材料,采用XRD验证了η-Al₂O₃与γ-Al₂O₃在晶相结构上的差异,比较了两者的表面形貌、织构及酸碱性能,结果显示,η-Al₂O₃与γ-Al₂O₃的比表面积相当,但η-Al₂O₃具有更弱的弱碱位和较少的强碱位,并拥有丰富的中等强度酸性位。将η-Al₂O₃与γ-Al₂O₃作为催化剂应用于CS₂水解反应,结果表明,在(200~450) ℃测试温度范围内,η-Al₂O₃催化剂对CS₂的水解活性始终优于γ-Al₂O₃,两种催化剂上CS₂反应的浓度效应也明显不同,推测与它们的酸碱性质影响了对CS₂的吸附能力有关,导致两者催化CS₂水解反应遵循了不同的机制。     

M/γ-Al2O3催化剂对煤油水重整制氢的影响

以γ-Al₂O₃为载体,采用等体积分步浸渍法制备了以Ni为活性组分,La、Ce、Fe、Cr、Co为助剂的催化剂M/γ-Al₂O₃,在固定床管式反应器中研究了M/γ-Al₂O₃催化剂的性能,考察了反应温度、水碳比和空速对氢产率的影响,并对催化剂进行XRD、SEM和BET表征。结果表明,NiLaCeFeCrCo/γ-Al₂O₃催化剂具有较好的催化性能,在反应温度700 ℃、水碳物质的量比10和空速6 min^-1的条件下,氢产率达到27.335 mol·mol^-1,并在300 min内表现出较好的活性,平均氢产率为21.966 mol·mol^-1。     

A comparison of sodium-modified Rh/γ-Al2O3 and Pd/γ-Al2O3 catalysts operated under simulated TWC conditions

Addition of Na to Rh/γ-Al₂O₃ and Pd/γ-Al₂O₃ catalysts operated under identical simulated TWC conditions has dramatically different effects in the two cases (although the two metals respond similarly to Na promotion of NO_x reduction in the absence of gaseous oxygen). Na addition to rhodium has a detrimental effect as manifested by severe poisoning and decreased nitrogen selectivity over the greater part of the temperature range studied. In contrast, Na promotion significantly improves the overall performance of Pd/γ-Al₂O₃ catalysts under simulated TWC conditions. This is manifested by a considerable widening of the gas composition window over which palladium delivers high NO_x conversion, whilst at the same time exhibiting markedly improved selectivity towards N₂ formation. The very different behaviour of the two metals may be understood in terms of a single underlying effect, namely, the electronic influence of sodium ions on the adsorption strength (and hence relative coverages) of the various reactants on the metal surface.     

液相原位还原法制备钯基催化剂

采用液相原位还原法制备Pd/α-Al2O3催化剂,并应用于CO氧化偶联合成草酸二甲酯反应。对比实验发现,甲醛液相原位还原法制得的Pd基催化剂具有优异的催化活性,当Pd负载质量分数低至0.1%时,催化剂仍表现出较高的活性和稳定性。采用XRD和BET等对催化剂及载体进行表征,结果表明,催化剂活性与载体的比表面积、孔容和孔径没有必然联系。通过TEM发现,0.1%-Pd/α-Al2O3催化剂中的主要活性组分Pd具有较小的颗粒和较高的分散性,通过HRTEM发现,液相原位还原法制备的催化剂能够有效暴露出Pd(111)晶面。     

Carbon formation and its influence on ethanol steam reforming over Ni/Al2O3 catalysts

Ethanol steam reforming was studied over Ni/Al₂O₃ catalysts. The effect of support (- and γ-Al₂O₃), metal loading and a comparison between conventional H₂ reduction with an activation method employing a CH₄/O₂ mixture was investigated. The properties of catalysts were studied by N₂ physisorption, X-ray diffraction (XRD) and temperature programmed reduction (TPR). After activity tests, the catalysts were analyzed by scanning electron microscopy (SEM) and thermogravimetric analysis (TG/DTA). Ni supported on γ-Al₂O₃ was more active for H₂ production than the catalyst supported on -Al₂O₃. Metal loading did not affect the catalytic performance. The alternative activation method with CH₄/O₂ mixture affected differently the activity and stability of the Ni/γ-Al₂O₃ and the Ni/-Al₂O₃ catalyst. This activation method increased significantly the stability of Ni/-Al₂O₃ compared to H₂ reduction. SEM and TG/DTA analysis indicate the formation of filamentous carbon during the CH₄/O₂ activation step, which is associated with the increasing catalyst activity and stability. The effect of temperature on the type of carbon formed was investigated; indicating that filamentous coke increased activity while encapsulating coke promoted deactivation. A discussion about carbon formation and the influence on the activity is presented.     

NO reduction by CH4 in the presence of O2 over La2O3 supported on Al2O3

Dispersing La₂O₃ on δ- or γ-Al₂O₃ significantly enhances the rate of NO reduction by CH₄ in 1% O₂, compared to unsupported La₂O₃. Typically, no bend-over in activity occurs between 500° and 700°C, and the rate at 700°C is 60% higher than that with a Co/ZSM-5 catalyst. The final activity was dependent upon the La₂O₃ precursor used, the pretreatment, and the La₂O₃ loading. The most active family of catalysts consisted of La₂O₃ on γ-Al₂O₃ prepared with lanthanum acetate and calcined at 750°C for 10 h. A maximum in rate (mol/s/g) and specific activity (mol/s/m²) occurred between the addition of one and two theoretical monolayers of La₂O₃ on the γ-Al₂O₃ surface. The best catalyst, 40% La₂O₃/γ-Al₂O₃, had a turnover frequency at 700°C of 0.05 s⁻¹, based on NO chemisorption at 25°C, which was 15 times higher than that for Co/ZSM-5. These La₂O₃/Al₂O₃ catalysts exhibited stable activity under high conversion conditions as well as high CH₄ selectivity (CH₄ + NO vs. CH₄ + O₂). The addition of Sr to a 20% La₂O₃/γ-Al₂O₃ sample increased activity, and a maximum rate enhancement of 45% was obtained at a SrO loading of 5%. In contrast, addition of SO⁼₄ to the latter Sr-promoted La₂O₃/Al₂O₃ catalyst decreased activity although sulfate increased the activity of Sr-promoted La₂O₃. Dispersing La₂O₃ on SiO₂ produced catalysts with extremely low specific activities, and rates were even lower than with pure La₂O₃. This is presumably due to water sensitivity and silicate formation. The La₂O₃/Al₂O₃ catalysts are anticipated to show sufficient hydrothermal stability to allow their use in certain high-temperature applications.     

K-, CeO2-, and Mn-promoted Ni/Al2O3 catalysts for stable CO2 reforming of methane

Reforming of methane with carbon dioxide into syngas over Ni/γ-Al₂O₃ catalysts modified by potassium, MnO and CeO₂ was studied. The catalysts were prepared by impregnation technique and were characterized by N₂ adsorption/desorption isotherm, BET surface area, pore volume, and BJH pore size distribution measurements, and by X-ray diffraction and scanning electron microscopy. The performance of these catalysts was evaluated by conducting the reforming reaction in a fixed bed reactor. The coke content of the catalysts was determined by oxidation conducted in a thermo-gravimetric analyzer. Incorporation of potassium and CeO₂ (or MnO) onto the catalyst significantly reduced the coke formation without significantly affecting the methane conversion and hydrogen yield. The stability and the lower amount of coking on promoted catalysts were attributed to partial coverage of the surface of nickel by patches of promoters and to their increased CO₂ adsorption, forming a surface reactive carbonate species. Addition of CeO₂ or MnO reduced the particle size of nickel, thus increasing Ni dispersion. For Ni–K/CeO₂–Al₂O₃ catalysts, the improved stability was further attributed to the oxidative properties of CeO₂. Results of the investigation suggest that stable Ni/Al₂O₃ catalysts for the carbon dioxide reforming of methane can be prepared by addition of both potassium and CeO₂ (or MnO) as promoters.     

The effect of CeO2 structure on the activity of supported Pd catalysts used for methane steam reforming

Palladium (Pd) supported on CeO₂-promoted γ-Al₂O₃ with various CeO₂ (ceria) crystallinities, were used as catalysts in the methane steam reforming reaction. X-ray diffraction (XRD) analysis, FTIR spectroscopy of adsorbed CO, and X-ray photoelectron spectroscopy (XPS) were employed to characterize the samples in terms of Pd and CeO₂ structure and dispersion on the γ-Al₂O₃ support. These results were correlated with the observed catalytic activity and deactivation process. Arrhenius plots at steady-state conditions are presented as a function of CeO₂ structure. Pd is present on the oxidized CeO₂-promoted catalysts as Pd⁰, Pd⁺ and Pd²⁺, at ratios strongly dependent on CeO₂ structure. XRD measurements indicated that Pd is well dispersed (particles <2 nm) on crystalline CeO₂ and is agglomerated as large clusters (particles in 10–20 nm range) on amorphous CeO₂. FTIR spectra of adsorbed CO revealed that after pre-treatment under H₂ or in the presence of amorphous CeO₂, partial encapsulation of Pd particles occurs. CeO₂ structure influences the CH₄ steam reforming reaction rates. Crystalline CeO₂ and dispersed Pd favor high reaction rates (low activation energy). The presence of CeO₂ as a promoter conferred high catalytic activity to the alumina-supported Pd catalysts. The catalytic activity is significantly lower on Pd/γ-Al₂O₃ or on amorphous (reduced) CeO₂/Al₂O₃ catalysts. The reaction rates are two orders of magnitude higher on Pd/CeO₂/γ-Al₂O₃ than on Pd/γ-Al₂O₃, which is attributed to a catalytic synergism between Pd and CeO₂. The low rates on the reduced Pd/CeO₂/Al₂O₃ catalysts can be correlated with the loss of Pd sites through encapsulation or particle agglomeration, a process found mostly irreversible after catalyst regeneration.     

Role of CeO2 in Ni/CeO2–Al2O3 catalysts for carbon dioxide reforming of methane

Ni catalysts supported on γ-Al₂O₃, CeO₂ and CeO₂–Al₂O₃ systems were tested for catalytic CO₂ reforming of methane into synthesis gas. Ni/CeO₂–Al₂O₃ catalysts showed much better catalytic performance than either CeO₂- or γ-Al₂O₃-supported Ni catalysts. CeO₂ as a support for Ni catalysts produced a strong metal–support interaction (SMSI), which reduced the catalytic activity and carbon deposition. However, CeO₂ had positive effect on catalytic activity, stability, and carbon suppression when used as a promoter in Ni/γ-Al₂O₃ catalysts for this reaction. A weight loading of 1–5 wt% CeO₂ was found to be the optimum. Ni catalysts with CeO₂ promoters reduced the chemical interaction between nickel and support, resulting in an increase in reducibility and stronger dispersion of nickel. The stability and less coking on CeO₂-promoted catalysts are attributed to the oxidative properties of CeO₂.     

Origin of transient species present on the surface of a PdO/γ-Al2O3 catalyst during the methane combustion reaction

Operando DRIFTS was applied to the study of the evolution of surface species formed on a Pd (2 wt.%)/γ-Al₂O₃ catalyst in various conditions. No differences were observed as a function of the initial oxidation state of palladium. Formates/carbonates species were identified at low temperature (<400 °C) and disappeared when CO₂ production started. These species come from the Pd-catalyzed interaction of CO with the alumina support, while CO₂ induces hydrogenocarbonates formation at low temperature (<300 °C). Their presence does not explain the inhibiting effect of CO₂ observed in CCM on Pd/γ-Al₂O₃ catalysts.     

Surface properties and reactivity of Cu/γ-Al2O3 catalysts for NO reduction by C3H6: Influences of calcination temperatures and additives

The influences of calcination temperatures and additives for 10 wt.% Cu/γ-Al₂O₃ catalysts on the surface properties and reactivity for NO reduction by C₃H₆ in the presence of excess oxygen were investigated. The results of XRD and XPS show that the 10 wt.% Cu/γ-Al₂O₃ catalysts calcined below 973 K possess highly dispersed surface and bulk CuO phases. The 10 wt.% Cu/γ-Al₂O₃ and 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalysts calcined at 1073 K possess a CuAl₂O₄ phase with a spinel-type structure. In addition, the 10 wt.% La–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses a bulk CuO phase. The result of NO reduction by C₃H₆ shows that the CuAl₂O₄ is a more active phase than the highly dispersed and bulk CuO phase. However, the 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses significantly lower reactivity for NO reduction than the 10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K, although these catalysts possess the same CuAl₂O₄ phase. The low reactivity for NO reduction for 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K is attributed to the formation of less active CuAl₂O₄ phase with high aggregation and preferential promotion of C₃H₆ combustion to CO_x by MnO₂. The engine dynamometer test for NO reduction shows that the C₃H₆ is a more effective reducing agent for NO reduction than the C₂H₅OH. The maximum reactivity for NO reduction by C₃H₆ is reached when the NO/C₃H₆ ratio is one.     

Nanosized γ-Al2O3 protective film for fluorescent lamps

Nanosized γ-Al₂O₃ particles were prepared by the sol–gel method with aluminum ion hydrolysis control performed by nitric acid. The as-prepared particles were mixed with deionized-water and stabilizer, and cycled in a high speed sand mill to form a stable γ-Al₂O₃ suspended slurry, which was then coated on the surface of the glass substrate to form a γ-Al₂O₃ protective film. Observations of SEM and visible transmission spectra show that a well-dispersed γ-Al₂O₃ slurry could be obtained after three-cycle grinding suitable to coat fluorescent lamp glass with a dense and uniform film of visible light transmission up to 95%.     

CeO2改性Ni/γ-Al2O3催化剂上顺酐加氢制备丁二酸酐

采用等体积浸渍法制备CeO₂改性Ni/γ-Al₂O₃催化剂,通过BET、XRD、H₂-TPR和SEM等对催化剂结构及物化性能进行表征,考察Ni-CeO₂/γ-Al₂O₃催化剂对顺酐催化加氢制备丁二酸酐催化性能的影响。结果表明,引入适量CeO₂可提高催化剂活性组分Ni的分散度,增加催化剂比表面积,提高催化剂热稳定性。采用负载CeO₂质量分数5%的Ni-CeO₂/γ-Al₂O₃催化剂,在反应温度120 ℃、反应压力2.0 MPa和空速0.6 h^-1条件下,顺酐转化率为99.5%,丁二酸酐选择性为99.4%。