Effects of carbon nanotubes and carbon fiber reinforcements on thermal conductivity and ablation properties of carbon/phenolic composites

The ablation properties and thermal conductivity of carbon nanotube (CNT) and carbon fiber (CF)/phenolic composites were evaluated for different filler types and structures. It was found that the mechanical and thermal properties of phenolic-polymer matrix composites were improved significantly by the addition of carbon materials as reinforcement. The concentrations of CF and CNT reinforcing materials used in this study were 30 vol% and 0.5 wt%, respectively. The thermal conductivity and thermal diffusion of the different composites were observed during ablation testing, using an oxygen–kerosene (1:1) flame torch. The thermal conductivity of CF mat/phenolic composites was higher than that of random CF/phenolic composites. Both CF mat and CNT/phenolic composites exhibited much better thermal conductivity and ablation properties than did neat phenolic resin. The more conductive carbon materials significantly enhanced the heat conduction and dissipation from the flame location, thereby minimizing local thermal damage.     

Thermal and mechanical properties of phenolic-based composites reinforced by carbon fibres and multiwall carbon nanotubes

The thermal, mechanical and ablation properties of carbon fibre/phenolic composites filled with multiwall carbon nanotubes (MWCNTs) were investigated. Carbon fibre/phenolic/MWCNTs were prepared using different weight percentage of MWCNTs by compression moulding. The samples were characterized by scanning electron microscopy (SEM), flexural tests, thermal gravimetric analysis and oxyacetylene torch tests. The thermal stability and flexural properties of the nanocomposites increased by increasing MWCNTs content (wt% ⩽1), but they decreased when the content of MWCNTs was 2 wt%. The linear and mass ablation rates of the nanocomposites after modified with 1 wt% MWCNTs decreased by about 80% and 52%, respectively. To investigate the material post-test microstructure, a morphological characterization was carried out using SEM. It was shown that the presence of MWCNTs in the composite led to the formation of a strong network char layer without any cracks or opening.     

Self sensing carbon nanotube (CNT) and nanofiber (CNF) cementitious composites for real time damage assessment in smart structures

The self sensing properties of cementitious composites reinforced with well dispersed carbon nanotubes and carbon nanofibers were investigated. The electrical resistance of cementitious nanocomposites with w/c = 0.3 reinforced with well dispersed carbon nanotubes (CNTs) and nanofibers (CNFs) at an amount of 0.1 wt% and 0.3 wt% of cement was experimentally determined and compared with resistivity results of nanocomposites fabricated with “as received” nanoscale fibers at the same loading. Results indicate that conductivity measurements, besides being a valuable tool in evaluating the smart properties of the nanocomposites, may provide a good correlation between the resistivity values measured and the degree of dispersion of the material in the matrix. The addition of CNTs and CNFs at different loadings was proven to induce a decrease in electrical resistance, with the nanocomposites containing 0.1 wt% CNTs yielding better electrical properties. Furthermore, conductivity measurements under cyclic compressive loading provided an insight in the piezoresistive properties of selected nanocomposites. Results confirm that nanocomposites, reinforced with 0.1 wt% CNTs and CNFs, exhibited an increased change in resistivity, which is indicative of the amplified sensitivity of the material in strain sensing.     

Effect of carbon nanotube type and functionalization on the electrical,thermal, mechanical and electromechanical properties of carbon nanotube/styrene–butadiene–styrene composites for large strain sensor applications

Thermoplastic elastomer tri-block copolymer, namely styrene–butadiene–styrene (SBS) composites filled with carbon nanotubes (CNT) are characterized with the main goal of obtaining electro-mechanical composites suitable for large deformation sensor applications. CNT/SBS composites with different filler contents and filler functionalizations are studied by morphological, thermal, mechanical and electrical analyses. It is shown that the different dispersion levels of CNT in the SBS matrix are achieved for pristine or functionalized CNT with strong influence in the electrical properties of the composites. In particular covalently functionalized CNTs show percolation thresholds higher than 8 weight percentage (wt%) whereas pristine CNT show percolation threshold smaller than 1 wt%. On the other hand, CNT functionalization does not alter the conduction mechanism which is related to hopping between the CNT for concentrations higher than the percolation threshold.Pristine single and multiwall CNT within the SBS matrix allow the preparation of composites with electro-mechanical properties appropriate for strain sensors for deformations up to 5% of strain, the gauge factor varying between 2 and 8. Composites close to the percolation threshold show larger values of the gauge factor.     

Influence of carbon nanotube-polymeric compatibilizer masterbatches on morphological, thermal, mechanical, and tribological properties of polyethylene

Study was made of the effect of multiwall carbon nanotubes (MWCNTs) and polymeric compatibilizer on thermal, mechanical, and tribological properties of high density polyethylene (HDPE). The composites were prepared by melt mixing in two steps. Carbon nanotubes (CNTs) were melt mixed with maleic anhydride grafted polyethylene (PEgMA) as polymeric compatibilizer to produce a PEgMA-CNT masterbatch containing 20 wt% of CNTs. The masterbatch was then added to HDPE to prepare HDPE nanocomposites with CNT content of 2 or 6 wt%. The unmodified and modified (hydroxyl or amine groups) CNTs had similar effects on the properties of HDPE-PEgMA indicating that only non-covalent interactions were achieved between CNTs and matrix. According to SEM studies, single nanotubes and CNT agglomerates (size up to 1 μm) were present in all nanocomposites regardless of content or modification of CNTs. Addition of CNTs to HDPE-PEgMA increased decomposition temperature, but only slight changes were observed in crystallization temperature, crystallinity, melting temperature, and coefficient of linear thermal expansion (CLTE). Young’s modulus and tensile strength of matrix clearly increased, while elongation at break decreased. Measured values of Young’s moduli of HDPE-PEgMA-CNT composites were between the values of Young’s moduli for longitudinal (E₁₁) and transverse (E₂₂) direction predicted by Mori-Tanaka and Halpin-Tsai composite theories. Addition of CNTs to HDPE-PEgMA did not change the tribological properties of the matrix. Because of its higher crystallinity, PEgMA possessed significantly different properties from HDPE matrix: better mechanical properties, lower friction and wear, and lower CLTE in normal direction. Interestingly, the mechanical and tribological properties and CLTEs of HDPE-PEgMA-CNT composites lie between those of PEgMA and HDPE.     

Reinforcing brittle and ductile epoxy matrices using carbon nanotubes masterbatch

In this study, the mechanical and thermal properties of epoxy composites using two different forms of carbon nanotubes (powder and masterbatch) were investigated. Composites were prepared by loading the surface-modified CNT powder and/or CNT masterbatch into either ductile or brittle epoxy matrices. The results show that 3 wt.% CNT masterbatch enhances Young’s modulus by 20%, tensile strength by 30%, flexural strength by 15%, and 21.1 °C increment in the glass transition temperature (by 34%) of ductile epoxy matrix. From scanning electron microscopy images, it was observed that the CNT masterbatch was uniformly distributed indicating the pre-dispersed CNTs in the masterbatch allow an easier path for preparation of CNT-epoxy composites with reduced agglomeration of CNTs. These results demonstrate a good CNT dispersion and ductility of epoxy matrix play a key role to achieve high performance CNT-epoxy composites.     

Processing,characterization, and modeling of carbon nanotube-reinforced multiscale composites

Carbon fiber-reinforced epoxy composites modified with carbon nanotubes (CNTs) were fabricated and characterized. High-energy sonication was used to disperse CNTs in the resin, followed by infiltration of fiber preform with the resin/CNT mixture. The effects of sonication time on the mechanical properties of “multiscale” composites, which contain reinforcements at varying scales, were studied. A low CNT loading of 0.3 wt% in resin had little influence on tensile properties, while it improved the flexural modulus, strength, and percent strain to break by 11.6%, 18.0%, and 11.4%, respectively, as compared to the control carbon fiber/epoxy composite. While sonication is an effective method to disperse CNTs in a resin, duration, intensity, and temperature need to be controlled to prevent damages imposed on CNTs and premature resin curing. A combination of Halpin–Tsai equations and woven fiber micromechanics was used in hierarchy to predict the mechanical properties of multiscale composites, and the discrepancies between the predicted and experimental values are explained.     

Preparation and thermal properties of soluble poly(phthalazinone ether sulfone ketone) composites reinforced with multi-walled carbon nanotube buckypaper

A nanocomposite with soluble high-performance poly(phthalazinone ether sulfone ketone) (PPESK) as matrix and multi-walled carbon nanotube buckypaper (MWCNT-BP) as reinforcement was fabricated by hot-press processing. The morphologies, dynamic and static mechanical behavior, thermal stability of the MWCNT-BP/PPESK composites were studied using scanning electron microscope (SEM), dynamic mechanical analyzer (DMA) and thermogravimetric analyzer (TGA). SEM microphotographs revealed a high impregnation degree of the MWCNT-BP/PPESK composites. Dynamic and static mechanical analysis revealed that the nanocomposites possessed high storage modulus, and good retention rate of mechanical strength even at 250 °C, which is mainly attributed to satisfied impregnation and strong interactions between MWCNT-BP and PPESK. Thermogravimetric analysis exhibited that the nanocomposites had excellent thermal stability. These investigations confirm that MWCNT-BP can be effectively used to manufacture high-loading CNT/PPESK composites with improved properties.     

Effects of carbon nanotubes and its functionalization on the thermal and flammability properties of polypropylene/wood flour composites

In this article, pristine carbon nanotubes (CNTs) and hydroxylated CNTs (CNT-OH) were employed to enhance the thermal stability and flame retardancy of polypropylene (PP)/wood flour composites (WPC) compatibilzed by maleic anhydride-grafted polypropylene (PP-g-MA). Incorporating 10 wt% PP-g-MA only enhanced the mechanical and thermal properties to some extent, but did not improve the flame retardancy of WPC. Thermogravimetric analysis (TGA) showed that the thermal stability of WPC was further increased with the addition of CNTs or CNT-OH and the increase of their loading level. Cone calorimeter measurements suggested that CNTs and CNT-OH could effectively reduce the peak heat release rate (PHRR) of WPC, and the flame retardancy properties reached the optimum value when both of their loading was 1.0 wt%, for instance, a reduction in PHRR by 16.7% and 25% for CNTs and CNT-OH, respectively. In addition, CNT-OH conferred better flame retardancy on WPC relative to pristine CNTs due to the better interfacial adhesion with wood flour and PP matrix, which was evidenced by scanning electron microscopy (SEM) observations.     

Improvement of toughness and electrical properties of epoxy composites with carbon nanotubes prepared by industrially relevant processes

The addition of carbon nanotubes (CNTs) to polymeric matrices or master batches has the potential to provide composites with novel properties. However, composites with a uniform dispersion of CNTs have proved to be difficult to manufacture, especially at an industrial scale. This paper reports on processing methods that overcome problems related to the control and reproducibility of dispersions. By using a high pressure homogenizer and a three-roll calendaring mill in combination, CNT reinforced epoxies were fabricated by mould casting with a well dispersed nanofiller content from 0.1 to 2 wt%. The influence of the nano-carbon reinforcements on toughness and electrical properties of the CNT/epoxies was studied. A substantial increase of all mechanical properties already appeared at the lowest CNT content of 0.1 wt%, but further raising the nanofiller concentration only led to moderate further changes. The most significant enhancement was obtained for fracture toughness, reaching up to 82%. The low percolation thresholds were confirmed by electrical conductivity measurements on the same composites yielding a threshold value of only about 0.01 wt%. As corroborated by a thorough microscopic analysis of the composites, mechanical and electrical enhancement points to the formation of an interconnected network of agglomerated CNTs.     

Mechanical and thermal properties of chicken feather fiber/PLA green composites

Chicken feather fiber (CFF)/reinforced poly(lactic acid) (PLA) composites were processed using a twin-screw extruder and an injection molder. The tensile moduli of CFF/PLA composites with different CFF content (2, 5, 8 and 10 wt%) were found to be higher than that of pure PLA, and a maximum value of 4.2 GPa (16%↑) was attained with 5 wt% of CFF without causing any substantial weight increment. The morphology, evaluated by scanning electron microscopy (SEM), indicated that an uniform dispersion of CFF in the PLA matrix existed. The mechanical and thermal properties of pure PLA and CFF/PLA composites were compared using dynamic mechanical analysis (DMA), thermomechanical analysis (TMA) and thermogravimetric analysis (TGA). DMA results revealed that the storage modulus of the composites increased with respect to the pure polymer, whereas the mechanical loss factor (tan δ) decreased. The results of TGA experiments indicated that the addition of CFF enhanced the thermal stability of the composites as compared to pure PLA. The outcome obtained from this study is believed to assist the development of environmentally-friendly composites from biodegradable polymers, especially for converting agricultural waste – chicken feather into useful products.     

Fabrication and effective thermal conductivity of multi-walled carbon nanotubes reinforced Cu matrix composites for heat sink applications

A novel particles-compositing method was used for the first time to disperse different contents of multi-walled carbon nanotubes (CNTs) in micron sized copper powders, which were subsequently consolidated into CNT/Cu composites by spark plasma sintering (SPS). Microstructural observations showed that the homogeneous distribution of CNTs and dense composites could be obtained for 0–10 vol.% CNT contents. The CNT clusters were appeared in the powder mixture with 15 vol.% CNTs, which resulted in an insufficient densification of the composites. The effective thermal conductivity of the composites was analyzed both theoretically and experimentally. The addition of CNTs showed no enhancement in overall thermal conductivity of the composites due to the interface thermal resistance associated with the low phase contrast of CNT to copper and the random tube orientation. Besides, the composite containing 15 vol.% CNTs led to a rather low thermal conductivity due possiblely to the combined effect of unfavorable factors induced by the presence of CNT clusters, i.e. large porosity, lower effective conductivity of CNT clusters themselves and reduction of SPS cleaning effect. The CNT/Cu composites may be a promising thermal management material for heat sink applications.     

Dispersion assessment and studies on AC percolative conductivity in polymer-derived Si–C–N/CNT ceramic nanocomposites

Nanocomposites comprise polysilazane-derived SiCN ceramic charged with carbon nanotubes (CNTs) have been prepared by dispersion of multi-walled CNTs with a diameter of 80 nm in a cross-linked polysilazane (HTT 1800, Clariant) using a simple roll-mixer method. Subsequently, the composites were warm pressed and pyrolyzed in argon atmosphere. Scanning electron microscopy (SEM) and 3D Raman imaging techniques were used as major tools to assess the dispersion of CNTs throughout the ceramic matrix. Furthermore, studies on the effect of the volume fraction of CNTs in the nanocomposites on their electrical properties have been performed. The specific bulk conductivities of the materials were analyzed by AC impedance spectroscopy, revealing percolation thresholds (ρ_c) at CNT loadings lower than 1 vol%. Maximum conductivity amounted to 7.6 × 10⁻² S/cm was observed at 5 vol% CNT. The conductivity exponent in the SiCN/CNT composites was found equal to 1.71, indicating transport in three dimensions.     

Enhancing the adhesive wear performance of polyetherimide composites through nano-particle treatment of the carbon fabric

Rare earth compound Ytterbium fluoride (YbF₃) in nano-size (40–80 nm) was employed for surface treatment of carbon fabric (CF) to improve its wettability with polyetherimide matrix. Composites were developed based on untreated and surface-treated CF with three doses, 0.1, 0.3, and 0.5 wt%, of YbF₃ in ethyl alcohol suspension. The composites were analyzed for interlaminar shear strength (ILSS). Improvement in ILSS was observed for treated fabric reinforced composites and it was maximum (61%) for 0.3 wt% dose of YbF₃. The adhesive wear performance of composites was evaluated by sliding a pin of composite against mild steel disc under varying loads (200–600 N). The treated fabric composites exhibited lower coefficient of friction (μ) and higher wear resistance (W _R). ILSS and W _R showed good linear correlation. Both properties were highest for 0.3% YbF₃ dosing. Increased roughness of fiber surface and adhesion of nano-particles on the fiber surface was observed in scanning electron microscopic (SEM) studies. SEM studies of worn surfaces of composites were performed to understand wear mechanisms. Atomic force microscopic studies indicated substantial increase in roughness value of CF.     

Fabrication and properties of CNTs/carbon fabric hybrid multiscale composites processed via resin transfer molding technique

Carbon nanotubes (CNTs) are effective fillers/reinforcements regarding improving the properties of polymer. In the present paper, carboxylic acid functionalized CNTs were used to modify epoxy with intent to develop a nanocomposite matrix for hybrid multiscale composites combining benefits of nanoscale reinforcement with well-established fibrous composites. CNTs were dispersed in epoxy by using high energy sonication. At low contents of CNTs, hybrid multiscale composites specimens were manufactured via resin transfer molding (RTM) process. The processibility of CNTs/epoxy systems was explored with respect to their viscosity. The dispersion quality and re-agglomeration behavior of CNTs in epoxy were characterized using optical microscope. A CNTs loading of 0.025 wt% significantly improved the glass transition temperatures (Tg) of the hybrid multiscale composites. Scanning electron microscopy (SEM) was used to examine the fracture surface of the failed specimens. It is demonstrated that the addition of small amount of CNTs (0.025 wt%) to epoxy for the fabrication of multiscale carbon fabric composites via RTM route effectively improves the matrix-dominated properties of polymer based composites. Hybridization efficiency in carbon fiber reinforced composites using CNTs is found to be highly dependent on the changes in the dispersion state of CNTs in epoxy.     

In situ preparation and mechanical properties of CNTs/MCMBs composites

By adding carbon nanotubes (CNTs) into medium temperature coal tar pitch, mesocarbon microbeads (MCMBs) were obtained via thermal condensation, then CNTs/MCMBs composites were in situ prepared using compression molding. The morphology, structure and mechanical properties of CNTs/MCMBs composites were characterized by optical microscope, digital camera, scanning electron microscope (SEM) and mechanical test machine. Results showed that CNTs were used as the nucleating agent and could inhibit the growth and coalescence of MCMBs. The optical textures of CNTs/MCMBs composites showed similar characteristics to the thermal condensation products from coal tar pitch with CNTs. The mass ratio of CNTs to coal tar pitch played an important role in the mechanical properties of CNTs/MCMBs composites. The density and bending strength of CNTs/MCMBs composite first increased and then decreased with the increase of the proportion of CNTs. When the proportion of CNTs was 5 wt%, the density of the composite reached the maximum (1.76 g/cm³). In addition, the bending strength of the composite reached the maximum (79.6 MPa) as adding 2 wt% CNTs into coal tar pitch.     

Evaluation and visualization of the percolating networks in multi-wall carbon nanotube/epoxy composites

In this study, epoxy-based nanocomposites containing multi-wall carbon nanotubes (CNTs) were produced by a calendering approach. The electrical conductivities of these composites were investigated as a function of CNT content. The conductivity was found to obey a percolation-like power law with a percolation threshold below 0.05 vol.%. The electrical conductivity of the neat epoxy resin could be enhanced by nine orders of magnitude, with the addition of only 0.6 vol.% CNTs, suggesting the formation of a well-conducting network by the CNTs throughout the insulating polymer matrix. To characterize the dispersion and the morphology of CNTs in epoxy matrix, different microscopic techniques were applied to characterize the dispersion and the morphology of CNTs in epoxy matrix, such as atomic force microscopy, transmission electron microscopy, and scanning electron microscopy (SEM). In particular, the charge contrast imaging in SEM allows a visualization of the overall distribution of CNTs at a micro-scale, as well as the identification of CNT bundles at a nano-scale. On the basis of microscopic investigation, the electrical conduction mechanism of CNT/epoxy composites is discussed.     

Experimental study to assess the effect of carbon nanotube addition on the through-thickness electrical conductivity of CFRP laminates for aircraft applications

The present paper tests experimentally the through-thickness electrical conductivity of carbon fiber-reinforced polymer (CFRP) composites laminates for aircraft applications. Two types of samples were prepared: Type A samples with carbon nanotubes (CNTs) and Type B samples without CNTs. During the electrical experiments, electrical currents of several mA were injected through the specimens. Electrical resistance was monitored simultaneously in order to deduce the changes in the through-the-thickness electrical conductivity caused by the addition of CNTs. Improvement of electrical conduction by two orders of magnitude was achieved through the addition of 1 wt% carbon nanotubes as compared to classic CFRP without CNTs. For moisture saturated samples, the influence of moisture absorption on such measures was found to be negligible.     

Dynamic fracture of carbon nanotube/epoxy composites under high strain-rate loading

We investigate dynamic fracture of three types of multiwalled carbon nanotube (MWCNT)/epoxy composites and neat epoxy under high strain-rate loading (${10}^5''–''{10}^6$ s⁻¹). The composites include randomly dispersed, 1 wt%, functionalized and pristine CNT/epoxy composites, as well as laminated, ∼50 wt% CNT buckypaper/epoxy composites. The pristine and functionalized CNT composites demonstrate spall strength and fracture toughness slightly higher and lower than that of neat epoxy, respectively, and the spall strength of laminated CNT buckypaper/epoxy composites is considerably lower; both types of CNTs reduce the extent of damage. Pullout, sliding and immediate fracture modes are observed; the fracture mechanisms depend on the CNT–epoxy interface strength and fiber strength, and other microstructures such as the interface between CNT laminates. Compared to the functionalized CNT composites, weaker CNT–epoxy interface strength and higher fiber strength lead to a higher probability of sliding fracture and higher tensile strength in the pristine CNT composites at high strain rates. On the contrary, sliding fracture is more pronounced in the functionalized CNT composites under quasistatic loading, a manifestation of a loading-rate effect on fracture modes. Despite their helpful sliding fracture mode and large CNT content, the weak laminate–laminate interfaces play a detrimental role in fracture of the laminated CNT buckypaper/epoxy composites. Regardless of materials, increasing strain rates leads to pronounced rise in tensile strength and fracture toughness.     

Dual strengthening mechanisms induced by carbon nanotubes in roll bonded aluminum composites

The dual role of carbon nanotubes (CNTs) in strengthening roll bonded aluminum composites has been elucidated in this study. An increase in the elastic modulus by 59% has been observed at 2 vol.% CNT addition in aluminum, whereas tensile strength increases by 250% with 9.5 vol.% CNT addition. CNTs play a dual role in the strengthening mechanism in Al–CNT composite foil, which can be correlated to the degree of dispersion of CNTs in the matrix. Better CNT dispersion leads to improvement of elastic properties. In contrast, CNT clusters in the aluminum matrix impede dislocation motion, causing strain hardening and thus improvement in the tensile strength. Dislocation density of the composites has been computed as a function of CNT content to show the effect on strain hardening of the metal matrix–CNT composite.