Enhanced substrate degradation and methane yield with maleic acid pre-treatments in biomass crops and residues

Organic acids are envisaged as alternative catalysts to strong mineral acids, in pre-treatment of ligno-cellulosic biomass for anaerobic digestion (AD). To evaluate this hypothesis, an untreated control and four pre-treatments (25 °C for 24 h) involving two levels of maleic acid (34.8 and 69.6 kg m⁻³), alone and combined with sulphuric acid (4 kg m⁻³), were studied in three agricultural substrates: Arundo (aka giant reed), Barley straw and B133 fibre sorghum. Methane production was assessed in a batch AD assay (35 °C for 51 days) with 4 g L⁻¹ of volatile solid (VS) load. Fibre composition and structure were investigated through chemical analysis and Fourier transform infrared (FTIR) spectrometry. Arundo and B133 that were the most and least recalcitrant substrate, respectively, staged the highest and lowest increase in methane with high maleic acid: +62% over 218 cm³ g⁻¹ of VS in untreated Arundo; +36% over 284 cm³ g⁻¹ of VS in untreated B133. Barley straw showed an intermediate behaviour (+41% over 269 cm³ g⁻¹ of VS). H₂SO₄ addition to maleic acid did not improve CH₄ output. The large increase in methane yield determined by pre-treatments was reflected in the concurrent decrease of fibre (between 14 and 39% depending on fibrous component). Based on FTIR spectra, bands assigned to hemicellulose and cellulose displayed lower absorbance after pre-treatment, supporting the hypothesis of solubilisation of structural carbohydrates and change in fibre structure. Hence, maleic acid was shown a suitable catalyst to improve biodegradability of ligno-cellulosic biomass, especially in recalcitrant substrates as Arundo.     

Improving methane production from wheat straw by digestate liquor recirculation in continuous stirred tank processes

Wheat straw is an abundant, cheap substrate that can be used for methane production. However, the nutrient content in straw is inadequate for methane fermentation. In this study, recycling digestate liquor was implemented in single-stage continuous stirred tank processes for enrichment of the nutrient content of straw with the aim of improving the methane production. The VS-based organic loading rate was set at 2 g/(L d) and the solid retention time at 40 days. When wheat straw alone was used as the substrate, the methane yields achieved with digestate liquor recycling was on average 240 ml CH₄/g VS giving a 21% improvement over the processes without recycling. However, over time, the processes suffered from declining methane yields and poor stability evidenced by low pH. To maintain process stability, wheat straw was co-digested with sewage sludge or supplemented with macronutrients (nitrogen and phosphorous). As a result, the processes with digestate liquor recycling could be operated stably, achieving methane yields ranging from 288 to 296 ml CH₄/g VS. Besides, the processes could not be operated sturdily with supplementation of macronutrients without digestate liquor recycling. The highest methane yield (296 ± 16 ml CH₄/g VS) was achieved by co-digestion with sewage sludge plus recycling of digestate liquor after filtration (retention of nutrients and microorganisms). This was comparable to the maximum expected methane yield of 293 ± 13 ml CH₄/g VS achieved in batch test. The present study therefore demonstrated that digestate liquor recycling could lead to a decreased dilution of vital nutrients from the reactors thereby rendering high process performance and stability.     

Optimization of mechanical pre-treatment of Laminariaceae spp. biomass-derived biogas

Macroalgae have not met their full potential to date as biomass for the production of energy. One reason is the high cost associated with the pretreatment which breaks the biomass's crystalline structure and better exposes the fermentable sugars to anaerobes. In the attempt to overcome this technological barrier, the performance of a Hollander beater mechanical pretreatment is assessed in this paper. This pretreatment has been applied to a batch of Laminariaceae biomass and inoculated with sludge from a wastewater treatment plant. The derived biogas and methane yields were used as the responses of a complex system in order to identify the optimal system input variables by using the response surface methodology (RSM). The system's inputs considered are the mechanical pretreatment time (5–15 min range), the machine's chopping gap (76–836 μm) and the mesophilic to thermophilic range of temperatures (30–50 °C). The mechanical pretreatment was carried out with the purpose of enhancing the biodegradability of the macroalgal feedstock by increasing the specific surface area available during the anaerobic co-digestion. The pretreatment effects on the two considered responses are estimated, discussed and optimized using the tools provided by the statistical software Design-Expert v.8. The best biogas yield of treated macroalgae was found at 50 °C after 10 min of treatment, providing 52% extra biogas and 53% extra methane yield when compared to untreated samples at the same temperature conditions. The highest biogas rate achieved by treating the biomass was 685 cc gTS⁻¹, which is 430 cc gTS⁻¹ in terms of CH₄ yield.     

Combined ethanol and methane production from switchgrass (Panicum virgatum L.) impregnated with lime prior to steam explosion

Pretreatments are crucial to achieve efficient conversion of lignocellulosic biomass to soluble sugars. In this light, switchgrass was subjected to 13 pretreatments including steam explosion alone (195 °C for 5, 10 and 15 min) and after impregnation with the following catalysts: Ca(OH)₂ at low (0.4%) and high (0.7%) concentration; Ca(OH)₂ at high concentration and higher temperature (205 °C for 5, 10 and 15 min); H₂SO₄ (0.2% at 195 °C for 10 min) as reference acid catalyst before steam explosion. Enzymatic hydrolysis was carried out to assess pretreatment efficiency in both solid and liquid fraction. Thereafter, in selected pretreatments the solid fraction was subjected to simultaneous saccharification and fermentation (SSF), while the liquid fraction underwent anaerobic digestion (AD). Lignin removal was lowest (12%) and highest (35%) with steam alone and 0.7% lime, respectively. In general, higher cellulose degradation and lower hemicellulose hydrolysis were observed in this study compared to others, depending on lower biomass hydration during steam explosion. Mild lime addition (0.4% at 195 °C) enhanced ethanol in SSF (+28% than steam alone), while H₂SO₄ boosted methane in AD (+110%). However, methane represented a lesser component in combined energy yield (ethanol, methane and energy content of residual solid). Mild lime addition was also shown less aggressive and secured more residual solid after SSF, resulting in higher energy yield per unit raw biomass. Decreased water consumption, avoidance of toxic compounds in downstream effluents, and post process recovery of Ca(OH)₂ as CaCO₃ represent further advantages of pretreatments involving mild lime addition before steam explosion.     

Steam explosion pretreatment and enzymatic saccharification of duckweed (Lemna minor) biomass

Our previous research has shown that duckweed is potentially an ideal feedstock for the production of biofuels because it can be effectively saccharified enzymatically. Here we report the results of experiments in which duckweed was pre-treated by steam explosion prior to enzyme digestion. A range of temperatures, from 130 to 230 °C with a fixed retention time of 10 min, were employed. The best pretreatment conditions were 210 °C for 10 min; these conditions produced the highest amount of water-soluble material (70%), the greatest levels of starch solubilisation (21%) and hemicellulose and pectic polysaccharides degradation (60%). The use of these steam explosion conditions enabled large reductions in the concentrations of enzymes required for effective saccharification. The amount of Celluclast required was reduced from 100 U (4.35 FPU) g⁻¹ substrate to 20 U g⁻¹ substrate, and additional beta-glucosidase was reduced from 100 to 2 U g⁻¹ substrate.     

Net N2O and CH4 soil fluxes of annual and perennial bioenergy crops in two central German regions

The area used for bioenergy feedstock production is increasing because substitution of fossil fuels by bioenergy is promoted as an option to reduce greenhouse gas (GHG) emissions. However, agriculture itself contributes to rising atmospheric nitrous oxide (N₂O) and methane (CH₄) concentrations. In this study we tested whether the net exchanges of N₂O and CH₄ between soil and atmosphere differ between annual fertilized and perennial unfertilized bioenergy crops. We measured N₂O and CH₄ soil fluxes from poplar short rotation coppice (SRC), perennial grass-clover and annual bioenergy crops (silage maize, oilseed rape, winter wheat) in two central German regions for two years. In the second year after establishment, the N₂O emissions were significantly lower in SRC (<0.1 kg N₂O–N ha⁻¹ yr⁻¹) than grassland (0.8 kg N₂O–N ha⁻¹ yr⁻¹) and the annual crop (winter wheat; 1.5 kg N₂O–N ha⁻¹ yr⁻¹) at one regional site (Reiffenhausen). However, a different trend was observed in the first year when contents of mineral nitrogen were still higher in SRC due to former cropland use. At the other regional site (Gierstädt), N₂O emissions were generally low (<0.5 kg N₂O–N ha⁻¹ yr⁻¹) and no crop-type effects were detected. Net uptake of atmospheric CH₄ varied between 0.4 and 1.2 kg CH₄–C ha⁻¹ yr⁻¹ with no consistent crop-type effect. The N₂O emissions related to gross energy in the harvested biomass ranged from 0.07 to 6.22 kg CO₂ equ GJ⁻¹. In both regions, Gierstädt (low N₂O emissions) and more distinct Reiffenhausen (medium N₂O emissions), this energy yield-related N₂O emission was the lowest for SRC.     

Energy recovery from grass of urban roadside verges by anaerobic digestion and combustion after pre-processing

Grass from urban roadside verges is a potential, though widely unused, resource for bioenergy recovery. Two possible bioenergy recovery techniques were tested, i.e. i) direct anaerobic digestion of the whole parent material and ii) the “integrated generation of solid fuel and biogas from biomass” (IFBB) procedure, which divides biomass into a press fluid and a press cake by mashing and mechanical dewatering. Biomass yield, chemical composition and canopy height of biomass, contribution of functional groups, fermentation characteristics of silage and press fluids, as well as characteristics of the produced solid fuel was investigated, applying a 4-cut management for anaerobic digestion, a 2-cut management for IFBB and an 8 times mulching as a reference. Mean annual biomass yield (2013 and 2014) was 3.24, 3.33 and 5.68 t dry matter ha⁻¹ for the mulching, 4-cut management and 2-cut management, respectively. Yields were higher in 2014 due to more favourable weather conditions. Fibre concentration was higher in material of the 2-cut management than in the 4-cut management, however, methane yield of the corresponding silages was the same. Highest methane yield was gained from press fluids with 292 l_N kg⁻¹ volatile solids. The press cake had a lower heating value of 16 MJ kg⁻¹ dry matter and a K₂O/CaO index of 0.51–0.88. Gross energy output was 26.4 GJ ha⁻¹ for anaerobic digestion and 84.4 GJ ha⁻¹ for IFBB. Thus, an altered roadside verge management with reduced cutting frequency might allow a significant energy recovery and improved ecosystem services, i.e. increased biodiversity.     

Sweet sorghum as a whole-crop feedstock for ethanol production

The potential of sweet sorghum as an alternative crop for ethanol production was investigated in this study. Initially, the enzymatic hydrolysis of sorghum grains was optimized, and the hydrolysate produced under optimal conditions was used for ethanol production with an industrial strain of Saccharomyces cerevisiae, resulting in an ethanol concentration of 87 g L⁻¹. From the sugary fraction (sweet sorghum juice), 72 g L⁻¹ ethanol was produced. The sweet sorghum bagasse was submitted to acid pretreatment for hemicellulose removal and hydrolysis, and a flocculant strain of Scheffersomyces stipitis was used to evaluate the fermentability of the hemicellulosic hydrolysate. This process yielded an ethanol concentration of 30 g L⁻¹ at 23 h of fermentation. After acid pretreatment, the remaining solid underwent an alkaline extraction for lignin removal. This partially delignified material, known as partially delignified lignin (PDC), was enriched with nutrients in a solid/liquid ratio of 1 g/3.33 mL and subjected to simultaneous saccharification and fermentation (SSF) process, resulting in an ethanol concentration of 85 g L⁻¹ at 21 h of fermentation. Thus, from the conversion of starchy, sugary and lignocellulosic fractions approximately 160 L ethanol.ton⁻¹ sweet sorghum was obtained. This amount corresponds to 13,600 L ethanol.ha⁻¹.     

Supercritical water gasification of timothy grass as an energy crop in the presence of alkali carbonate and hydroxide catalysts

This study is focused on identifying the candidature of timothy grass as an energy crop for hydrogen-rich syngas production through supercritical water gasification. Timothy grass was gasified in supercritical water to investigate the impacts of temperature (450–650 °C), biomass-to-water ratio (1:4 and 1:8) and reaction time (15–45 min) in the pressure range of 23–25 MPa. The impacts of carbonate catalysts (e.g., Na₂CO₃ and K₂CO₃) and hydroxide catalysts (e.g., NaOH and KOH) at variable mass fractions (1–3%) were examined to maximize hydrogen yields. In the non-catalytic gasification of timothy grass, highest hydrogen (5.15 mol kg⁻¹) and total gas yields (17.2 mol kg⁻¹) with greater carbon gasification efficiency (33%) and lower heating value (2.21 MJ m⁻³) of the gas products were obtained at 650 °C with 1:8 biomass-to-water ratio for 45 min. However, KOH at 3% mass fraction maximized hydrogen and total gas yields up to 8.91 and 30.6 mol kg⁻¹, respectively. Nevertheless, NaOH demonstrated highest carbon gasification efficiency (61.3%) and enhanced lower heating value of the gas products (4.68 MJ m⁻³). Timothy grass biochars were characterized through Fourier transform infrared spectroscopy, Raman spectroscopy and scanning electron microscopy to understand the behavior of the feedstock to rising temperature and reaction time. The overall findings suggest that timothy grass is a promising feedstock for hydrogen production via supercritical water gasification.     

Characterization,pretreatment and saccharification of spent seaweed biomass for bioethanol production using baker's yeast

Seaweeds are marine macroalgae found abundantly and viewed as potential source of phycocolloids to produce biofuel. In this study, seaweed spent biomass obtained from alginate production industry and biomass obtained after pigment extraction were found to contain a considerable amount of phycocolloids. These two spent biomasses were investigated for the production of ethanol. In this study, the red seaweed spent biomass of Gracilaria corticata var corticata showed higher content of polysaccharide (190.71 ± 30.67 mg g⁻¹ dry weight) than brown seaweed spent biomass (industrial) (136.28 ± 30.09 mg g⁻¹ dry weight). Hydrolysis of spent biomasses with different concentrations of sulfuric acid (0.1%, 0.5% and 1%) was also investigated. Brown seaweed spent biomass and red seaweed spent biomass exhibited high amount of sugar in 0.5% and 1% sulfuric acid treatment, respectively. Proximate and ultimate composition of seaweed spent biomasses were analysed for energy value. The FT-Raman spectra exhibited similar stretches for both acid hydrolysed spent biomasses with their respective standards. Ethanol produced through a fermentation process using spent hydrolysates with baker's yeast at pH 5.3 was found to be significant. The ethanol yield from brown seaweed spent biomass and red seaweed spent biomass was observed to be 0.011 g g⁻¹ and 0.02 ± 0.003 g g⁻¹ respectively, when compared with YPD (0.42 ± 0.03 g g⁻¹) and d-galactose (0.37 ± 0.04 g g⁻¹) as standard on day 4. The present study revealed the possibility of effective utilization of spent biomass from seaweed industry for ethanol production.     

Anaerobic digestion of maize and cellulose under thermophilic and mesophilic conditions – A comparative study

The aim of this study was to advance in understanding of digestion process of energy crops. Cellulose and maize silage were fermented in batch mode at mesophilic (38 °C) and thermophilic (55 °C) conditions and corresponding organic loads of 5.5 ± 0.2 kgVS/m³, 11.2 ± 0.3 kgVS/m³ and 16.7 ± 0.4 kgVS/m³.For both substrates more stable and faster digestion took place at 38 °C. Due to complex structure maize degradation was characterized by varying digestion rate and longer total digestion time resulting form breakdown of hard-degradable fractions. The digestion retard at increased OLRs of cellulose and lower degradation level obtained for all cellulose series confirm a higher overloading potential for systems dealing with single-component-substrates but also the enhanced sensitivity of such systems to any inconvenient digestion conditions.Based on observed patterns of volatile fatty acids and oxidation-reduction potential, different fermentation mechanisms can be concluded for cellulose and maize, but also for different temperature modes. Conversion of maize at highly reductive conditions with increased concentrations of butyric acid was accompanied by much higher activity of hydrogenotrophic methanogens than for cellulose digestion.Two factors showed a strong potential to influence test results: an insufficient VS content of inoculum, which caused reduced biogas yields, and a high natural biodiversity of maize silage, resulting in higher biogas yields than calculated based on the maize composition.     

Compositional differences among upland and lowland switchgrass ecotypes grown as a bioenergy feedstock crop

Feedstock quality mainly depends upon the biomass composition and bioenergy conversion system being used. Higher cellulose and hemicellulose concentrations are desirable for biochemical conversion, whereas higher lignin is favored for thermochemical conversion. The efficiency of these conversion systems is influenced by the presence of high nitrogen and ash concentrations. Switchgrass (Panicum virgatum L.) varieties are classified into two ecotypes based on their habitat preferences, i.e., upland and lowland. The objectives of this study were to quantify the chemical composition of switchgrass varieties as influenced by harvest management, and to determine if ecotypic differences exist among them. A field study was conducted near Ames, IA during 2012 and 2013. Upland (‘Cave-in-Rock’, ‘Trailblazer’ and ‘Blackwell’) and lowland switchgrass varieties (‘Kanlow’ and ‘Alamo’) were grown in a randomized block design with six replications. Six biomass harvests were collected at approximately 2-week intervals each year. In both years, delaying harvest increased cellulose, hemicellulose and lignin concentrations while decreasing nitrogen and ash concentrations in all varieties. On average, Kanlow had the highest cellulose and hemicellulose concentration (354 and 321 g kg⁻¹ DM respectively), and Cave-in-Rock had the highest lignin concentration (33 g kg⁻¹ DM). The lowest nitrogen and ash concentrations were observed in Kanlow (14 and 95 g kg⁻¹ DM respectively). In general, our results indicate that delaying harvest until fall improves feedstock quality, and ecotypic differences do exist between varieties for important feedstock quality traits. These findings also demonstrate potential for developing improved switchgrass cultivars as bioenergy feedstock by intermating lowland and upland ecotypes.     

Growth,yield, fiber content and lodging resistance in eight varieties of Cenchrus purpureus (Schumach.) Morrone intended as energy crop

Growth, biomass yield, fiber content and lodging resistance were studied, during a six month growth period, for eight varieties of Cenchrus purpureus, intended as energy crop, in Veracruz, Mexico. Then, only yield at day 182 was assessed for two additional years. The varieties were: CT115 (CT), African Cane (AC), Taiwan (TAI), King Grass (KG), Vruckwona (VRU), Roxo (RX), OM22 (OM) and Cameroon (CAM). Local weather is warm and sub-humid, historical data for monthly average temperature and annual rainfall were 25.8 °C and 1142 mm, respectively. Height, diameter and light interception were measured monthly from day 65–185. At day 185, biomass yield and tiller density were measured. Number of lying tillers was counted to estimate lodging resistance. Cellulose and hemicellulose content were estimated in leaf and stem. No differences were found for dry matter yield or stem yield at day 185 in the first year. Regarding the next two years, TAI yielded above CT, OM or ROX. Average dry matter yield was higher in the second year than in the establishment cycle (38.6 vs 21.1 Mg ha⁻¹), but decreased in the third year (32.2 Mg ha⁻¹). In both stem and whole plant, AC and KG showed higher hemicellulose content than RX, OM or CT; while AC and VRU had higher cellulose than RX in stem, or than CT in the whole plant. Furthermore, varieties AC, KG, VRU and TAI were resistant to lodging and had a higher fiber content, so they are recommended as energetic crops.     

Upgraded biofuel from residue biomass by Thermo-Catalytic Reforming and hydrodeoxygenation

Research is focused on the utilisation of waste or residue biomass for bioenergy conversion. A promising conversion technology for the production of liquid biofuels from residue biomass is a process called Thermo-Catalytic Reforming (TCR^®​) which is a combination of prior thermal treatment of the biomass at mild temperatures (intermediate pyrolysis) followed by a second catalytic treatment step at elevated temperatures (reforming). This article focuses on the conversion of TCR^® liquids from digestate as a feedstock for subsequent hydrocarbon production. The generated bio-oil showed a lower heating value of 34.0 MJ kg⁻¹ with an oxygen content of 7.0% and a water content of 2.2%. The bio-oil was hydrodeoxygenated using an industrial NiMo–Al₂O₃ catalyst at temperatures of 503 K–643 K and a pressure of 14 MPa. The hydrodeoxygenated bio-oil reached a lower heating value of 42.3 MJ kg⁻¹ with an oxygen content below 0.8 mg kg⁻¹ and water content of 30 ppm. Product yields and catalyst life give confidence that upgrading of the TCR^®​ bio-oil offers a suitable option to meet the high standards of common fuels.     

Hydrogen,ethanol and cellulase production from pulp and paper primary sludge by fermentation with Clostridium thermocellum

Pulp and paper industry primary sludge being largely composed of lignocellulosic fibres, it could be used as carbon source by bacteria having cellulolytic capability. The aim of this study was to evaluate the use of cellulose contained in this type of sludge for Clostridium thermocellum to produce ethanol, hydrogen and cellulases. In an ATCC 1191 medium containing 5 kg m⁻³ dry primary sludge from recycled paper mill, batch culture reached stationary phase after 2 days. All of the available cellulose was hydrolysed after 60 h of incubation, with a final pH of 5.83. Metabolites produced after 60 h of fermentation were acetate (8.50 mol m⁻³), ethanol (11.30 mol m⁻³), lactate (8.75 mol m⁻³), formate (0.27 mol m⁻³), hydrogen (11.20 mol m⁻³) and carbon dioxide (18.41 mol m⁻³). Cellulase activity was detected in the supernatant after 36 h, with a maximal activity of 0.25 U cm⁻³ at 72 h. Pulp and paper primary sludge appeared to be a readily usable substrate for C. thermocellum at this concentration, yielding both potential biofuels (hydrogen and ethanol) as well as active cellulases.     

Lignocellulosic ethanol production employing immobilized Saccharomyces cerevisiae in packed bed reactor

Most of ethanol production processes are limited by lower ethanol production rate and recyclability problem of ethanologenic organism. In the present study, immobilized co-fermenting Saccharomyces cerevisiae GSE1618 was employed for ethanol fermentation using rice straw enzymatic hydrolysate in a packed bed reactor (PBR). The immobilization of S. cerevisiae was performed by entrapment in Ca-alginate for optimization of ethanol production by varying alginic acid concentration, bead size, glucose concentration, temperature and hardening time. Remarkably, extra hardened beads (EHB) immobilized with S. cerevisiae could be used up to repeated 40 fermentation batches. In continuous PBR, maximum 81.82 g L⁻¹ ethanol was obtained with 29.95 g L⁻¹ h⁻¹ productivity with initial glucose concentration of 180 g L⁻¹ in feed at dilution rate of 0.37 h⁻¹. However, maximum ethanol concentration of 40.33 g L⁻¹ (99% yield) with 24.61 g L⁻¹ h⁻¹ productivity was attained at 0.61 h⁻¹ dilution rate in fermentation of un-detoxified rice straw enzymatic hydrolysate (REH). At commercial scale, EHB has great potential for continuous ethanol production with high productivity using lignocellulosic hydrolysate in PBR.     

Environmental assessment of electricity generation from an Italian anaerobic digestion plant

A standard ISO Life Cycle Assessment study was carried out to evaluate the environmental sustainability of electricity production from an anaerobic digestion (AD) plant using a mixture of dedicated energy crops, agricultural residues and livestock effluents as input materials. The functional unit was 1 MJ of electricity. System boundaries were from cradle to grave and covered all the phases from energy crops cultivation to the production of biogas and its use in a Combined Heat and Power plant to produce electricity. Liquid and solid digestate storage and spreading on agricultural land were included. Primary data were collected from the AD plant for all the above phases. Since heat produced is used only internally, no allocation was applied in the study. As regards digestate management, CH₄ emissions were calculated from literature, whereas four literature methods were applied for calculation of nitrogen emissions with the goal to perform a sensitivity analysis on LCA results. ILCD Handbook impact assessment methodologies were used. Results show that the main hotspots are energy crops cultivation and the management of digestate, mainly because of both nitrogen and methane emissions, affecting Global Warming, Acidification, Marine and Freshwater Eutrophication. Finally, a detailed Monte Carlo analysis, was carried out to evaluate the results uncertainty. The study represents the state of the art about the environmental performance of the AD plant with the use of sensitivity and uncertainty analysis, which both improve the reliability of results, and allows drawing general conclusions on how to mitigate the environmental impacts of AD process.     

Corn stover ethanol yield as affected by grain yield,Bt trait,and environment

Literature values for glucose release from corn stover are highly variable which would likely result in tremendous variability in bio-refinery ethanol yield from corn stover feedstock. A relatively recent change in United States corn genetics is the inclusion of the Bacillus thuringiensis (Bt) trait, which now accounts for three-fourths of all US planted corn acreage. The objective of this study was to evaluate the effect of corn grain yield, inclusion of the Bt trait, and location environment on corn stover quality for subsequent ethanol conversion. Two hybrid pairs (each having a Bt and non-Bt near-isoline) were analyzed giving a total of 4 hybrids. In 2010 and 2011, field plots were located in Michigan at four latitudinal differing locations in four replicated plots at each location. Stover composition and enzymatic digestibility was analyzed and estimated ethanol yield (g g⁻¹) was calculated based on hydrolyzable glucan and xylan levels. Analysis showed that there were no significant differences in total glucose or xylose levels nor in enzymatically hydrolyzable glucan and xylan concentrations between Bt corn stover and the non-Bt stover isolines. Regression analyses between corn grain yield (Mg ha⁻¹) and corn stover ethanol yield (g g⁻¹) showed an inverse relationship indicative of a photosynthate source-sink relationship. Nevertheless, the quantity of stover produced was found to be more critical than the quality of stover produced in maximizing potential stover ethanol yield on a land area basis.     

Assessing sustainable forest biomass potential and bioenergy implications for the northern Lake States region,USA

Forestlands in the United States have tremendous potential for providing feedstocks necessary to meet emerging renewable energy standards. The Lake States region is one area recognized for its high potential of supplying forest-derived biomass; however, the long-term availability of roundwood harvests and associated residues from this region has not been fully explored. Better distribution and temporal availability estimates are needed to formulate emerging state policies regarding renewable energy development. We used a novel predictive methodology to quantify sustainable biomass availability and likely harvest levels over a 100-year period in the Lake States region. USDA Forest Inventory and Analysis estimates of timberland were combined with published growth and yield models, and historic harvest data using the Forest Age Class Change Simulator (FACCS) to generate availability estimates. Monte-Carlo simulation was used to develop probability distributions of biomass harvests and to incorporate the uncertainty of future harvest levels. Our results indicate that 11.27–15.71 Mt y⁻¹ dry roundwood could be sustainably harvested from the Lake States. Assuming 65% collection rate, 1.87–2.62 Mt y⁻¹ residue could be removed, which if substituted for coal would generate 2.12–2.99 GW h of electricity on equivalent energy basis while reducing GHG (CO₂e) emission by 1.91–2.69 Mt annually. In addition to promoting energy security and reducing GHG emissions, forest residues for energy may create additional revenues and employment opportunities in a region historically dependent on forest-based industries.     

Cob biomass supply for combined heat and power and biofuel in the north central USA

Corn (Zea mays L.) cobs are being evaluated as a potential bioenergy feedstock for combined heat and power generation (CHP) and conversion into a biofuel. The objective of this study was to determine corn cob availability in north central United States (Minnesota, North Dakota, and South Dakota) using existing corn grain ethanol plants as a proxy for possible future co-located cellulosic ethanol plants. Cob production estimates averaged 6.04 Tg and 8.87 Tg using a 40 km radius area and 80 km radius area, respectively, from existing corn grain ethanol plants. The use of CHP from cobs reduces overall GHG emissions by 60%–65% from existing dry mill ethanol plants. An integrated biorefinery further reduces corn grain ethanol GHG emissions with estimated ranges from 13.9 g CO₂ equiv MJ⁻¹ to 17.4 g CO₂ equiv MJ⁻¹. Significant radius area overlap (53% overlap for 40 km radius and 86% overlap for 80 km radius) exists for cob availability between current corn grain ethanol plants in this region suggesting possible cob supply constraints for a mature biofuel industry. A multi-feedstock approach will likely be required to meet multiple end user renewable energy requirements for the north central United States. Economic and feedstock logistics models need to account for possible supply constraints under a mature biofuel industry.