Improving the Tribological Behavior of Graphite/Cu Matrix Self-Lubricating Composite Contact Strip by Electroplating Zn on Graphite

Studies to explore the nature of friction, and in particular thermally activated friction in macroscopic tribology, have lead to a series of experiments on thin coatings of molybdenum disulfide. Coatings of predominately molybdenum disulfide were selected for these experiments; five different coatings were used: MoS₂/Ni, MoS₂/Ti, MoS₂/Sb₂O₃, MoS₂/C/Sb₂O₃, and MoS₂/Au/Sb₂O₃. The temperatures were varied over a range from −80 °C to 180 °C. The friction coefficients tended to increase with decreasing temperature. Activation energies were estimated to be between 2 and 10 kJ/mol from data fitting with an Arrhenius function. Subsequent room temperature wear rate measurements of these films under dry nitrogen conditions at ambient temperature demonstrated that the steady-state wear behavior of these coatings varied dramatically over a range of K = 7 × 10⁻⁶ to 2 × 10⁻⁸ mm³/(Nm). It was further shown that an inverse relationship between wear rate and the sensitivity of friction coefficient with temperature exists. The highest wear-rate coatings showed nearly athermal friction behavior, while the most wear resistant coatings showed thermally activated behavior. Finally, it is hypothesized that thermally activated behavior in macroscopic tribology is reserved for systems with stable interfaces and ultra-low wear, and athermal behavior is characteristic to systems experiencing gross wear.     

Ultra-High Tribological Performance of Magnetron Sputtered a-C:H Films in Sand-Dust Environment

The hydrogenated amorphous carbon (a-C:H) films were prepared on AISI 440C steel substrates using a RF magnetron sputtering graphite target in the CH₄ and Ar mixture atmosphere. The friction and wear behavior of a-C:H films were comparatively investigated by pin-on-disc tester under dry sliding and simulated sand-dust wear conditions. In addition, the effects of applied load, amount of sand and sand particle sizes on the tribological performance of a-C:H films were systemically studied. Results show that a-C:H films exhibited ultra-high tribological performance with low friction coefficient and ultra-low wear rate under sand-dust environments. It is very interesting to observe that the friction coefficient of a-C:H film under sand-dust conditions was relatively lower when compared with dry sliding condition, and the wear rate under sand-dust conditions kept at the same order of magnitude (×10⁻¹⁹ m³/N m) with the increase of applied load and particle size as a comparison with the dry sliding condition. Based on the formation of “ridge” layer (composite transfer layer), a transfer layer-hardening composite model was established to explain the anti-wear mechanisms and friction-reducing capacity of a-C:H solid lubrication films under sand-dust conditions.     

Effect of Fluoride Content on Friction and Wear Performance of Ni<Subscript>3</Subscript>Al Matrix High-Temperature Self-Lubricating Composites

The self-lubricating composites Ni₃Al–BaF₂–CaF₂–Ag–Cr, which have varying fluoride contents, were fabricated by the powder metallurgy technique. The effect of fluoride content on the mechanical and tribological properties of the composites was investigated. The results showed that an optimal fluoride content and a balance between lubricity and mechanical strength were obtained. The Ni₃Al–6.2BaF₂–3.8CaF₂–12.5Ag–10Cr composite showed the best friction coefficients (0.29–0.38) and wear rates (4.2 × 10⁻⁵–2.19 × 10⁻⁴ mm³ N⁻¹ m⁻¹) at a wide temperature range (room temperature to 800°C). Fluorides exhibited a good reduced friction performance at 400 and 600°C. However, at 800°C, the formation of BaCrO₄ on the worn surface due to the tribo-chemical reaction at high temperatures provided an excellent lubricating property.     

Tribological Property of Ni<Subscript>3</Subscript>Al Matrix Composites with Addition of BaMoO<Subscript>4</Subscript>

The Ni₃Al matrix composites with addition of 10, 15, and 20 wt% BaMoO₄ were fabricated by powder metallurgy technique, and the tribological behaviors were studied from room temperature to 800 °C. It was found that BaAl₂O₄ formed during the fabrication process. The Ni₃Al composites showed poor tribological property below 400 °C, with high friction coefficients (above 0.6) and wear rates (above 10⁻⁴ mm³/Nm). However, the composites exhibited excellent self-lubricating and anti-wear properties at higher temperatures, and the composite with addition of 15 wt% BaMoO₄ had the lowest wear rate (1.10 × 10⁻⁵ mm³/Nm) and friction coefficient (0.26). In addition, the results also indicated that BaAl₂O₄ for the Ni₃Al composites did not exhibit lubricating property from room temperature to 800 °C.     

NiAl Matrix High-Temperature Self-Lubricating Composite

A high-temperature self-lubricating composite NiAl–Cr–Mo–CaF₂ was fabricated using the powder metallurgy technique, and the tribological behavior of the composite at a wide range of temperatures (room temperature to 1000 °C) was investigated. The results showed that the composite had a favorable friction coefficient of about 0.2 and an excellent wear resistance of about 1 × 10⁻⁵ mm³N⁻¹m⁻¹ at the high temperatures tested (800 and 1000 °C). The excellent self-lubricating performance was attributed to the formation of the glaze film on the worn surface consisting mainly of CaCrO₄ and CaMoO₄ as high-temperature solid lubricants.     

Tribological Properties of Spark-Plasma-Sintered ZrO2(Y2O3)–Al2O3–Ba x Sr1?x SO4 (x?=?0.25, 0.5, 0.75) Composites at Elevated Temperature

Self-lubricating ZrO₂(Y₂O₃)–Al₂O₃–Ba _x Sr_1−x SO₄ (x = 0.25, 0.5, 0.75) composites have been fabricated by spark plasma sintering (SPS) method. The tribological properties have been evaluated using a high-temperature friction and wear tester at room temperature and 760 °C in dry sliding against alumina ball. The composites exhibit distinct improvements in effectively reducing friction and wear, as compared to the unmodified ZrO₂(Y₂O₃)–Al₂O₃ ceramics. The ZrO₂(Y₂O₃)–Al₂O₃–Ba _x Sr_1−x SO₄ (x = 0.25, 0.5, 0.75) composites have great low and stable friction coefficients of less than 0.15 and wear rates in the order of 10^− 6mm³/Nm at 760 °C. Delamination is considered as the dominating wear mechanism of the composites at room temperature. At elevated temperature, the formation and effective spreading of Ba _x Sr_1−x SO₄ (x = 0.25, 0.5, 0.75) lubricating films during sliding play an important role in the reduction of the friction and wear.     

Effect of Applied Load and Surface Roughness on the Tribological Properties of Ni-Based Superalloys Versus Ta<Subscript>2</Subscript>AlC/Ag or Cr<Subscript>2</Subscript>AlC/Ag Composites

The novel Ta₂AlC–20 vol.% Ag (TaAg) and Cr₂AlC–20 vol.% Ag (CrAg) composites were tribologically tested versus a Ni-based superalloy Inc718 (SA) by dry sliding at a sliding speed of 1 m/s at room temperature in air at loads from 3 N to 18 N. The TaAg composites were also tested at 8 and 18 N at 550 °C, and at a 3 N load against the SA with different surface roughnesses at 26 °C and 550 °C. At room temperatures, the coefficients of friction, μ’s, decreased from ~0.8–0.9 to ~0.3–0.4 for both the TaAg and CrAg composites as the applied normal force increased from 3 N to 8 N. Further increases in load to 18 N did not change the μ’s. The specific wear rates, sWR, increased with increased loads for the TaAg composite; they remained almost unchanged for the CrAg composite. This behavior was attributed to the formation of glaze tribofilms—similar to ones observed previously in these tribocouples at elevated temperatures and 3 N—promoted by the increased loads. Preconditioning of the SA surface by sliding against the TaAg composite at 550 °C and 8 N resulted in μ’s of <0.2 and sWR < 10⁻⁶ mm³/N-m in subsequent room temperature sliding at 3 N. Somewhat higher, but stable room temperature μ’s of ~0.3 and sWR of ~3 × 10⁻⁵ mm³/N-m were observed when the TaAg composites were slid versus a sandblasted SA surface at 500 °C and 3 N. It follows that in situ preconditioning of the tribo-surfaces is a powerful tool for improving the properties of the MAX/Ag-SA tribocouples. The relationship between sliding conditions, chemistries of tribofilms, and their properties are discussed.     

The effect of hard coated metals on the thermo‐oxidative stability of a branched perfluoropolyalkylether lubricant

M‐50 and carburized Pyrowear 675® (Carpenter Technology, Reading PA, USA) steel coupons deposited with commercially available physical vapour deposited TiN, TiCN, TiAlCN, TiCrCN/TiB₄C multilayer, electroless Ni (E‐Ni) TiN and E‐Ni TiCN coatings were immersed in a branched perfluoropolyalkylether (PFPAE), Krytox AC® (E.I. du pont de Nemours and Company, Wilmington DE, USA), in an oxidative environment at temperatures ranging from 315 to 360 °C for a duration of 24 hours and compared with uncoated coupons. Coated and uncoated Pyrowear 675® coupons demonstrated superior corrosion resistance compared with coated and uncoated M‐50 respectively. The coatings most resistant to chemical attack in the PFPAE fluid were TiCN, E‐Ni TiN and E‐Ni TiCN. Copyright © 2006 John Wiley & Sons, Ltd.     

Tribological characteristics of polycrystalline Magnéli-type titanium dioxides

The results presented in this paper have clarified experimentally, that titania-based Magnéli-phases (Ti₄O₇/Ti₅O₉ and Ti₆O₁₁) with (121)-shear planes exhibit more anti-wear properties than lubricious (low-frictional) properties. The results for dry sliding indicate that the coefficients of friction lie in the range of 0.1–0.6 depending on sliding speed and ambient temperature. The COF decreased with increasing temperature (T= 22–800°C) and increasing sliding speed (υ= 1−6 m/s). The dry sliding wear rate was lowest for the Al₂O₃ at 1 m/s at 800°C with values of 1.7 × 10−8 and 6.4 × 10−8 mm³/N m, comparable to boundary/mixed lubrication, associated with a high dry frictional power loss of 30 W/mm². The running-in wear length and, more important, the wear rate decreased under oscillating sliding tests with increasing relative humidity. The contact pressure for high-/low-wear transition increased under oscillating sliding tests with increasing relative humidity. At room temperature and a relative humidity of 100% the steady-state wear rate under dry oscillating sliding for the couple Al₂O₃/Ti₄O₇–Ti₅O₉ was lower than 2 × 10−7 mm³/N m and therefore inferior to the resolution of the continuous wear measurement sensor. TEM of wear tracks from oscillating sliding revealed at room temperature a work-hardening as mechanism to explain the running-in behavior and the high wear resistance. The hydroxylation of titania surfaces favours the high-/low-wear transition. This revised version was published online in August 2006 with corrections to the Cover Date.     

Ni3Al Matrix Composite with Lubricious Tungstate at High Temperatures

Ni₃Al–Ag–BaF₂/CaF₂–W composites were fabricated by the powder metallurgy route, and their tribological properties over a wide temperature range, starting from room temperature up to 800 °C, were investigated. The Ni₃Al matrix composite with 15 wt% BaF₂/CaF₂ exhibited a favorable friction coefficient (range 0.3–0.4) and wear rate (0.2–6.2 × 10⁻⁴mm³ N⁻¹ m⁻¹). The formation of BaWO₄ and CaWO₄ with lubricity on the worn surface due to a tribo-chemical reaction at high temperatures provided excellent lubricating properties. The low friction coefficient over a broad temperature range could be attributed to the synergistic effect of Ag, BaF₂/CaF₂, BaWO₄, and CaWO₄.     

Effect of temperature on the fracture toughness of A516 Gr70 steel

Fracture toughness JIC and KIC tests were performed on A516 Gr70 carbon steel plate at the temperature ranging from −160°C to 600°C, and test results were analyzed according to ASTM E 813 and ASTM E 399. Unloading compliance J-integral tests were performed on ITCT specimens. The relation between the J_IC value and the test temperature was obtained. It was concluded that the temperature ranging from −15°C to 600°C is the upper shelf region of ductile-brittle transition temperature, and in this temperature range, fracture toughness J_IC values decreased with increasing temperature. The ductile brittle transition temperature of the material may be around −30°C. In the region near −30°C, the tendency of J_IC to decrease with decreasing temperature was significant.     

The tribological characteristics of TiCN coating at elevated temperatures

The tribological behaviour of TiCN coating prepared by unbalanced magnetron sputtering is studied in this work. The substrates made from austenitic steel were coated by TiCN coatings during one deposition. The measurements were provided by high temperature tribometer (pin-on-disc, CSM Instruments) allowing measuring the dependency of friction coefficient on cycles (sliding distance) up to 500 °C. The evolution of the friction coefficient with the cycles was measured under different conditions, such as temperature or sliding speed and the wear rate of the ball and coating were evaluated. The 100Cr6 balls and the Si₃N₄ ceramic balls were used as counter-parts. The former were used at temperatures up to 200 °C, the latter up to 500 °C. The wear tracks were examined by optical methods and SEM. The surface oxidation at elevated temperatures and profile elements composition of the wear track were also measured.The experiments have shown considerable dependency of TiCN tribological parameters on temperature. Rise in temperature increased both friction coefficient and the wear rate of the coating in case of 100Cr6 balls. The main wear mechanism was a mild wear at temperatures up to 200 °C; fracture and delamination were dominating wear mechanisms at temperatures from 300 to 500 °C.     

Tribological Properties of Arc-Evaporated NbAlN Hard Coatings

Nb_1−x Al _x N hard coatings were synthesised by cathodic arc-evaporation with different Al contents to study its influence on the tribological properties. Ball-on-disc tests at temperatures up to 700 °C were performed and the recorded coefficient of friction was generally in the range from 0.8 to 1.0. Subsequent analysis of the coating wear track and the counterpart wear scar by optical profilometry and Raman spectroscopy revealed details on the wear behaviour of the tested coatings. The best wear performance for the Nb-rich coatings was in the temperature range of 300–500 °C, whereas at the maximum testing temperature the higher oxidation resistance with increasing Al content was beneficial in terms of wear resistance.     

Experimental study of frost growth on a horizontal cold surface under forced convection

Frost formation on a horizontal copper surface under low air temperature and forced convection conditions is investigated experimentally. Both the frost crystals pattern and the frost layer thickness formed on the cold plate are compared under different experimental conditions. The environmental variables considered in this study include the ambient temperature (T _∞ ), air relative humidity (φ), and velocity (v), as well as the cold surface temperature (Tw). The tested ranges are −5≤T _∞ ≤5 °C, 50%≤ φ≤80%, 2.2≤v≤8.0 m/s, −16.8≤T _w ≤−25.5 °C. The experimental results show the cold surface temperature and the air relative humidity have obvious effects on the frost growth: the frost layer thickness increases strongly with the decreasing cold surface temperature and increasing air relative humidity. The air temperature and air velocity or Reynolds number are also important factors affecting the frost crystals’ growth and thickness. With the increase of the air temperature and velocity, the frost crystals become denser, and the frost layer thickness become thicker, but this trend becomes weaker under higher air temperature and velocity.     

Tribological behaviors and mechanisms of Ti<Subscript>3</Subscript>AlC<Subscript>2</Subscript>

Tribological behaviors and the relevant mechanism of a highly pure polycrystalline bulk Ti₃AlC₂ sliding dryly against a low carbon steel disk were investigated. The tribological tests were carried out using a block-on-disk type high-speed friction tester, at the sliding speeds of 20–60 m/s under a normal pressure of 0.8 MPa. The results showed that the friction coefficient is as low as 0.1∼0.14 and the wear rate of Ti₃AlC₂ is only (2.3–2.5) × 10⁻⁶ mm³/Nm in the sliding speed range of 20–60 m/s. Such unusual friction and wear properties were confirmed to be dependant dominantly upon the presence of a frictional oxide film consisting of amorphous Ti, Al, and Fe oxides on the friction surfaces. The oxide film is in a fused state during the sliding friction at a fused temperature of 238–324 °C, so it takes a significant self-lubricating effect.     

Low Friction CrNMPP/TiNDCMS Multilayer Coatings

Transition metal nitrides like CrN and TiN are widely used in automotive applications due to their high hardness and wear resistance. Recently, we showed that a multilayer architecture of CrN and TiN, deposited using the hybrid—high power impulse magnetron sputtering (HIPIMS) and direct current magnetron sputtering (DCMS)—HIPIMS/DCMS deposition technique, results in coatings which indicate not only increased mechanical and tribological properties but also friction coefficients in the range of diamond-like-carbon coatings when tested at RT and ambient air conditions. The modulated pulsed power (MPP) deposition technique was used to replace the HIPIMS powered cathode within this study to allow for a higher deposition rate, which is based on the complex MPP pulse configuration. Our results on MPP/DCMS deposited CrN/TiN multilayer coatings indicate excellent mechanical and tribological properties, comparable to those obtained for HIPIMS/DCMS. Hardness values are around 25 GPa with wear rates in the range of 2 × 10⁻¹⁶ Nm/m³ and a coefficient of friction around 0.05 when preparing a superlattice structure. The low friction values can directly be correlated to the relative humidity in the ambient air during dry sliding testing. A minimum relative humidity of 13% is necessary to guarantee such low friction values, as confirmed by repeated tests, which are even obtained after vacuum annealing to 700 °C. Our results demonstrate that the co-sputtering of high metal ion sputtering techniques and conventional DC sputtering opens a new field of applications for CrN/TiN coatings as high wear resistance and low friction coatings.     

Tribological performance of TiN and TiCN coatings on a working tool steel

Although the applications of TiN and TiCN coatings are extensive, their mechanical and tribological properties are influenced by the substrates in which they are deposited. The present work is focused on the tribological performance of TiN and TiCN coatings on a working tool steel. Besides, adhesion and microhardness tests were carried out. The adhesion performance of both coatings resulted in class 1, according to CEN/TS 1071–8 standard, which allows observing the quality of adhesion. The composite microhardness was investigated by the analysis of relative indentation (β). Pin-on-disk tests were performed in dry and lubricated condition at 100 °C against tungsten carbide (WC). Low friction coefficients of μ_k = 0.08 for TiN and μ_k = 0.03 for TiCN were obtained in lubricated conditions. Wear mechanisms were analyzed by scanning electron microscopy (SEM). Abrasive wear was observed as the principal wear mechanism in dry condition, while in lubricated conditions wear signals seem to be scarcely noticeable.     

Studies on wear behavior of nano-intermetallic reinforced Al-base amorphous/nanocrystalline matrix in situ composite

Resistance to wear is an important factor in design and selection of structural components in relative motion against a mating surface. The present work deals with studies on fretting wear behavior of in situ nano-Al₃Ti reinforced Al–Ti–Si amorphous/nanocrystalline matrix composite, processed by high pressure (8 GPa) sintering at room temperature, 350, 400 or 450 °C. The wear experiments were carried out in gross slip fretting regime to investigate the performance of this composite against Al₂O₃ at ambient temperature (22–25 °C) and humidity (50–55%). The highest resistance to fretting wear has been observed in the composites sintered at 400 °C. The fretting wear involves oxidation of Al₃Ti particles in the composite. A continuous, smooth and protective tribolayer is formed on the worn surface of the composite sintered at 400 °C, while fragmentation and spallation leads to a rougher surface and greater wear in the composite sintered at 450 °C.     

Thermal strain analysis of composite materials by electronic speckle pattern interferometry

This study discusses a non-contact optical technique (electronic speckle pattern interferometry) that is well suited for thermal deformation measurement without any surface preparation and compensating process. Fiber reinforced plastics ([0]₁₆, [0/90]_8S) were analyzed by ESPI to determine their thermal expansion coefficients. The thermal expansion coefficient of the transverse direction of a uniaxial composite is evaluated as 48.78×10⁻⁶(1/°C). Also, the thermal expansion coefficient of the cross-ply laminate [0/90]_8S is numerically estimated as 3.23×10⁻⁶ (1/°C) that is compared with that measured by ESPI.     

Friction and Wear Properties of Silicon Carbide in Water from Different Sources

Low friction and low wear of SiC sliding against itself in water at room temperature have been well reported in the past 20 years, and some practical applications have been developed. However, the properties of friction and wear in pure, deionized or distilled water have been mainly observed and not in water from sources in nature. In this article, the fundamental properties of friction and wear between SiC ball and disk are observed in water from ground, river, and sea, and the results are compared with those in deionized water in the viewpoints of modes of lubrication and wear and the resultant values of friction coefficient and wear rate. The smallest friction coefficient (μ_ℓ = 0.005) in steady state is observed in deionized water and the largest (μ_ℓ = 0.013) in sea water. The smallest wear rate (w _s = 2.2 × 10⁻⁷ mm³/Nm) is observed in sea water and the largest (w _s = 3.1 × 10⁻⁷ mm³/Nm) in deionized water. The intermediate values of μ_ℓ and w _s between the smallest and the largest ones are observed in ground and river water. The modes of lubrication and wear, which generated observed values of μ_ℓ and w _s, are considered as mixed lubrication and tribochemical wear. The chemical elements of Na, Cl, Mg, and K in sea water observed on wear particles and pits are thought effective to generate the largest value of μ_ℓ and the smallest value of w _s.