Super low friction of DLC applied to engine cam follower lubricated with ester-containing oil

This paper presents a material combination that reduces the friction coefficient markedly to a superlow friction regime (below 0.01) under boundary lubrication. A state approaching superlubricity was obtained by sliding hardened steel pins on a hydrogen-free diamond-like carbon (DLC) film (ta-C) lubricated with a poly-alpha-olefin (PAO) oil containing 1 mass% of an ester additive. This ta-C/steel material combination showed a superlow friction coefficient of 0.006 at a sliding speed of 0.1 m/s. A hydrogencontaining DLC coating/steel combination also showed a lower friction coefficient in air than a steel/steel combination, 0.1 vs. 0.8, but no large reduction was observed when the sliding surfaces were lubricated with ordinary 5W-30 engine oil and the PAO oil containing an ester additive. The friction coefficient of the hydrogen containing DLC/steel combination lubricated with the PAO containing an ester additive was above 0.05. On the other hand, the superlow friction performance demonstrates that the rolling contact friction level of needle roller bearings can be obtained in sliding contact under a boundary lubrication condition. It is planned to apply this advanced DLC coating technology to valve lifters lubricated with a newly formulated engine oil in actual mass-produced gasoline engines. A larger friction reduction of more than 45% is expected to be obtained at an engine speed of 2000 rpm.     

Addressing Practical Challenges of Low Friction Coefficient Measurements

A friction coefficient is defined as the ratio of the friction force to the applied normal force. Despite the disarming simplicity of its calculation, there are practical challenges that make low values of friction coefficient difficult to accurately quantify. The connections of imperfect parts in friction measurement devices (called tribometers) produce small misalignments between the transducer and counterface axes. According to Schmitz et al. (J Tribol Trans ASME 127:673–678, 2005), “…the measurement of friction coefficient is extremely sensitive to misalignments” and “for materials with friction coefficients below 0.05 the alignment becomes hopelessly difficult if the goal is to have uncertainties below 1%.” This method article reviews the challenges of low friction measurements and presents a robust reversal technique that eliminates misalignment bias. Experiments with controlled misalignment angles demonstrate the bias sensitivity and validate its elimination using a low uncertainty tribometer in conjunction with the described reversal technique.     

Bridging the Gap Between the Atomic-Scale and Macroscopic Modeling of Friction

A short survey of a modern view on the problem of friction from the physical viewpoint is presented. An atomically thin lubricant film confined between two substrates in moving contact has been studied with the help of molecular dynamics (MD) based on Langevin equations with coordinate- and velocity-dependent damping coefficient. Depending on model parameters, the system may exhibit either the liquid sliding regime, when the lubricant film melts during sliding (the “melting-freezing” mechanism of stick-slip motion), the “layer-over-layer” sliding regime, when the film keeps a layered structure at sliding, or the solid sliding regime, which may provide an extremely low friction (“superlubricity”). Atomic-scale MD simulations of friction, however, lead to a “viscosity” of the thin film, as well as to the critical velocity of the transition from stick-slip to smooth sliding, which differ by many orders of magnitude from the values observed in macroscopic experiments. This contradiction can be resolved with the help of the earthquakelike (EQ) model with a continuous distribution of static thresholds. The evolution of the EQ model is reduced to a master equation which can be solved analytically. This approach describes stick-slip and smooth sliding regimes of tribological systems within a framework which separates the calculation of the friction force from the atomic-scale studies of contact properties.     

An investigation into friction behaviour of dispersion-strengthened copper under severe railway braking conditions

A dispersion-strengthened copper (DSC) has been studied as an alternative material for railway brake discs, to be used in severe railway braking applications. Compared to standard steel, the DSC shows a more homogeneous thermal field at the friction surface. This also applies in depth, both avoiding hot spots. This thermal behaviour implies a lower wear and a very interesting friction coefficient evolution without any “anti-fade” phenomenon.     

A multi-scale model for friction in cold rolling of aluminium alloy

A simple and robust friction model is proposed for cold metal rolling in the mixed lubrication regime, based on physical phenomena across two length scales. At the primary roughness scale, the evolution of asperity contact area is associated with the asperity flattening process and hydrodynamic entrainment between the roll and strip surfaces. The friction coefficient on the asperity contacts is related to a theoretical oil film thickness and secondary-scale roll surface roughness. The boundary friction coefficient at the “true” asperity contacts is associated with tribo-chemical reactions between fresh metal, metal oxide, boundary additives, the tool and any transfer layer on the tool. The asperity friction model is verified by strip drawing simulations under thin film lubrication conditions with a polished tool, taking the fitting parameter of the boundary lubrication friction factor on the true contact areas equal to 0.1. Predicted values of average friction coefficient, using a boundary friction factor in the range 0.07–0.1, are in good agreement with measurements from laboratory and industrial rolling mill trials.     

Tribochemical interactions of Si-doped DLC film against steel in sliding contact

This study concerns the effects of tribochemical interactions at the interface of Si-DLC (silicon-doped diamond-like carbon) film and steel ball in sliding contact on tribological properties of the film. The Si-DLC film was over-coated on pure DLC coating by radio frequency plasma-assisted chemical vapor deposition (r.f. PACVD) with different Si concentration. Friction tests against steel ball using a reciprocating type tribotester were performed in ambient environment. X-Ray photoelectron spectroscopy (XPS) and auger electron spectroscopy (AES) were used to study the chemical characteristics and elemental composition of the films and mating balls after tests. Results showed a darkgray film consisting of carbon, oxygen and silicon on the worn steel ball surface with different thickness. On the contrary, such film was not observed on the surface of the ball slid against pure DLC coating. The oxidation of Si-DLC surface and steel ball was also found at particular regions of contact area. This demonstrates that tribochemical interactions occurred at the contact area of Si-DLC and steel ball during sliding to form a tribofilm (so called transfer film) on the ball specimen. While the pure DLC coating exhibited high coefficient of friction (∼0.06), the Si-DLC film showed a significant lower coefficient of friction (∼0.022) with the presence of tribofilm on mating ball surface. However, the Si-DLC film possesses a very high wear rate in comparison with the pure DLC. It was found that the tribochemical interactions strongly affected tribological properties of the Si-DLC film in sliding against steel.     

Lubrication Mechanisms of Lamellar Fatty Acid Fluids

The lubrication mechanisms of different lamellar fluids are investigated as they are introduced in the thin contact zone between two macroscopic surfaces in motion in a friction measurement set-up. We simultaneously measure the film thickness and its lubricative properties under controlled contact kinematics. The lamellar phases consist of nanometric flat bilayers of fatty acid surfactant molecules organized in periodic stacks separated by a water/ethylene diamine solution. First, we examine the film forming capability of these phases when the two surfaces are moving at the same velocity, i.e. in “pure rolling” conditions. We observe the growth of a thick film in the contact which eventually reaches a stable value. The relatively high viscosity of the film leads to a situation of so-called “starved lubrication”. By modelling the film build-up process, we determine the viscosity of the lubricant and its piezoviscosity. As shear is applied between the surfaces, the lubricant film exhibits a constant thickness and a rather low frictional response. We correlate this behaviour to the combination of a relatively high viscosity value together with a low piezoviscosity. Through the addition of a hydrophobic liquid (naphthenic oil) to the initial system, we increase the bilayer thickness whilst keeping the lamellar characteristic packing distance constant. This changes both the film forming capability and frictional behaviour of the lamellar fluid. We propose a model to account for the observed friction responses of both lamellar phases and discuss the shear localization in the lubricant film.     

Transient Elastohydrodynamic Limiting Shear Behaviour Related to Molecular Interaction

Previous studies have revealed that friction behaves in unexpected ways as pressure increases in a lubricating film. It has been determined that it is not a viscosity-related issue but rather originating directly from molecular structure. This study strives to elucidate the importance of understanding the properties that govern friction, when undertaking simulation of elastohydrodynamic events. A thorough investigation of the maximum transferable shear stress in the film for a paraffinic mineral oil has been undertaken. A previously stated theory of decreasing friction coefficient with increasing pressure is further substantiated by the current measurements. Classical thermodynamics, in the shape of transient “hot-wire” measurements, have been used to study macro-molecular changes (as function of pressure). The instance of global relaxation correlates nicely to measurements.     

甘油润滑下CrCN涂层的超低摩擦特性

为开发与CrCN涂层具有良好配伍润滑性能的绿色润滑剂,使用磁控溅射技术在304不锈钢表面沉积CrCN涂层,利用场发射扫描电子显微镜、原子力显微镜、纳米压痕仪、维氏硬度计、X射线衍射仪、X射线光电子能谱仪分别对其表面形貌、涂层厚度、力学性能、物相组成以及元素化学价态进行分析,并借助多功能摩擦磨损试验机评价在甘油润滑下CrCN涂层的摩擦学性能,并与PAO6润滑下结果进行比较。利用磁控溅射技术在不锈钢表面构筑的CrCN涂层表面光滑致密,粗糙度仅为1.01 nm,硬度可达14.39 GPa。对比钢-钢和钢-CrCN体系的摩擦学性能发现,钢-CrCN体系在甘油润滑下展现出优异的润滑性能;当负载为0.5 N时,钢-CrCN体系在甘油润滑下的摩擦因数可低至0.01,大大低于PAO6润滑下的摩擦因数。对磨痕的XPS分析表明,在摩擦过程中,甘油发生摩擦化学反应,在CrCN涂层的接触表面生成一层FeOOH层,甘油分子及其降解产物可能进一步吸附在FeOOH层,形成流体润滑层,有效降低了摩擦和磨损。     

The Frictional Properties of Newtonian Fluids in Rolling–Sliding soft-EHL Contact

A combined experimental and numerical study has been carried out to explore friction in rolling–sliding, soft-EHL contact. Experimental work has employed corn syrup solutions of different concentrations in water to provide a range of lubricant viscosities and has measured Couette friction in mixed rolling–sliding conditions over a wide range of entrainment speeds. A Stribeck curve has been generated, ranging from the boundary to full film, isoviscous-elastic lubrication regime. In the latter regime, friction coefficient is approximately proportional to the product of (entrainment speed × viscosity) raised to the power 0.55. Numerical solution of the isoviscous-elastic lubrication regime has been used to derive predictive equations for both Couette and Poiseuille friction in circular, soft-EHL contacts. This shows that in soft-EHL the Poiseuille or “rolling” friction can have magnitude comparable to the Couette friction. The calculated Poiseuille friction coefficient can be predicted from non-dimensional load and speed using a simple power law expression similar to that used for film thickness. However accurate prediction of calculated Couette friction coefficient requires a two-term power law expression. Comparison of experimental and numerical Couette friction coefficients shows quite good agreement between the two, with a similar non-dimensional speed dependence, but slightly lower predicted than measured values.     

Mechanical and tribological properties of amorphous carbon films

The mechanical and tribological properties of amorphous carbon films have been studied in more detail in recent years because these films (a) can be deposited near room temperature, thus allowing film deposition on common engineering alloys (i.e., aluminum and steel) without altering their mechanical properties, and (b) are smooth and conform to surface roughness of the substrate, thus requiring no post deposition processing. In addition, amorphous carbon films exhibit low unlubricated sliding friction in contact with steel and ceramics which is comparable to that of steel against steel in a lubricated contact. The wear resistance of these films is also better than Ti‐based hard coatings. Further improvement in film tribological properties can be achieved by modifying film chemical composition. Because of these attractive features, amorphous carbon films have been evaluated in several applications including automotive, electronic and biomedical engineering. However, environmental factors such as oxygen and humidity have been found to influence tribological properties significantly. This paper reviews the current understanding of the tribological properties of both hydrogenated and non‐hydrogenated amorphous carbon films, the mechanisms responsible for low friction coefficient and identifies areas that require further research. This revised version was published online in June 2006 with corrections to the Cover Date.     

Improved mixed and boundary lubrication with glycerol-diamond technology

Abstract

The fuel economy and reduction of harmful elements in lubricants are becoming important issues in the automotive industry. An approach to respond to these requirements is the potential use of low friction coatings in engine components exposed to boundary lubrication conditions. Diamond-like carbon (DLC) coatings extensively studied as ultralow friction films to protect the surfaces of ductile metals for space applications are expected to fulfil this part. The main purpose of this work is to investigate the friction and wear properties of glycerol lubricated DLC coatings under boundary lubrication conditions. The DLC material consists of tetrahedral hydrogen free amorphous diamond-like carbon (denoted as ta-C) as shown by the time of flight secondary ion mass spectroscopy (ToF-SIMS) analyses and the nanoindentation measurements. The friction coefficient below 0&middot.01, called superlubricity, and no measurable wear were obtained by sliding the ta-C/ta-C friction pair in the presence of pure glycerol as a lubricant at 353 K. The mechanism by which glycerol is able to reduce the friction in the millirange was revealed by ToF SIMS analyses inside and outside wear scars formed by friction experiments using deuterated glycerol and ¹³C glycerol.     

Measurement and Characterization of “Resonance Friction” at High Sliding Speeds in a Model Automotive Wet Clutch

The friction forces between various lubricated “friction materials” and sapphire disks were measured using a new “high-speed” rotating disk attachment to the surface forces apparatus (SFA). Two different clutch lubricants and two different friction materials were tested at sliding speeds and normal loads from 5 to 25 m/s, and 0.2 to 1 N (nominal pressures ~1 MPa), respectively. The results show that “resonance friction”—characterized by large amplitude oscillatory (i.e., sinusoidal) vibrations, also known as shudder or chatter—dominates dynamical considerations at high sliding speed, replacing the smooth sliding or low-amplitude stick–slip that is characteristic of low speed/low load sliding. The characteristic (rotational) speeds or frequencies at which resonance friction occurs depend only on the coupled/uncoupled mechanical resonance frequencies of the loading and friction-sensing mechanisms. In contrast, the intensity of and time to enter/exit shudder depends strongly on the lubricating oil and, to a lesser extent, on the friction material. Physical–chemical analyses of the friction materials before and after testing showed that the samples undergo primarily structural rather than chemical changes. Our results provide new fundamental insights into the resonance friction phenomenon and suggest means for its control.     

Amorphous hydrogenated carbon films for tribological applications I. Development of moisture insensitive films having reduced compressive stress

Although earlier investigations on the tribological behaviour of amcrphous hydrogenated carbon (AHC) films in sliding contact with steel showed encouraging results, four open issues were identified. They were: (a) dependence of friction and wear on humidity (i.e., the friction coefficient and the wear increased with humidity), (b) limitations on film thickness (i.e., films greater than 2 μm thick delaminated due to large compressive stress), (c) deposition of films on substrates other than silicon and (d) lubricant compatibility (i.e., formation of lubricant-derived antiwear films on AHC film surfaces). Steps were taken to address some of these open issues by incorporating silicon in AHC films. Friction and wear tests were conducted on AHC films containing various amounts of silicon. Incorporation of silicon in AHC films rendered the friction coefficients and the wear of a steel counterface insensitive to moisture. Silicon incorporation in AHC films also significantly reduced compressive stress. This allowed deposition of 10 μm thick films. These effects were achieved without any compromise with the friction coefficient and the film wear if the amount of silicon in the film was kept within a certain concentration range. In addition, silicon-containing AHC films were thermally more stable than silicon-free films. Experiments conducted with two lubricants resulted in significantly lower wear of the silicon-free AHC films than that obtained for unlubricated sliding. Similar friction coefficients were obtained for AHC film/steel and steel/steel combinations in lubricated sliding.     

Thin film lubrication of sliding point contacts of AISI 52100 steel

The mechanism of thin film lubrication of sliding point contacts of AISI 52100 steel has been studied as a function of load, sliding speed, composition and temperature of the lubricant.Below certain critical combinations of Hertzian pressure, speed and temperature the surfaces are kept apart by an elastohydrodynamic lubricant film. The load carrying capacity of this film depends primarily on the effective viscosity of the lubricant in the contact region which decreases with bulk oil temperature and with increasing sliding speed, because of friction induced thermal effects. After breakdown of the EHD film, boundary lubrication may still prevent severe adhesive wear. The transition from the boundary lubricated regime towards the regime of severe adhesive wear is a function of load (normal force), speed and bulk oil temperature and possibly depends on the conjunction temperature. Irrespective of the initial lubrication condition, oxidation of the steel surfaces leads to the (re)establishment of low friction, mild wear conditions.     

Sliding velocity dependency of the friction coefficient of Si-containing diamond-like carbon film under oil lubricated condition

In this study we investigated the sliding velocity dependency of the coefficient of friction for a Si-containing diamond-like carbon (DLC-Si) film in an automatic transmission fluid (ATF) under a wide range of contact pressures. The DLC-Si film and a nitrided steel with a surface roughness, Rz_JIS, of around 3.0 μm were used as disk specimens. A high-carbon chromium steel (JIS-SUJ2) bearing ball was used as a ball specimen. Friction tests were conducted using a ball-on-disk friction apparatus under a wide range of sliding velocites (0.1-2.0 m/s) and contact pressures (P_max: 0.42-3.61 GPa) in ATF. The friction coefficients for the nitrided steel had a tendency to decrease with an increase in sliding veloicity under all the contact pressure conditions; however, the friction coefficients for the DLC-Si film were stable with respect to sliding velocities under all the contatct pressures. These results indicate that the DLC-Si film suppresses the stick-slip motion during sliding againt steel in ATF, which is a desired frictional characteristic for the electromagnetic clutch disks used under lubrication. Furthermore, the DLC-Si film showed a higher wear resistance and lower aggression on the steel ball specimen than the nitrided steel. There were less hydrodynamic effects on the friction coefficient for the DLC-Si film possibly due to maintenance of the initial surface roughness and its poorer wettability with the fluid. X-ray photoelectron spectroscopy (XPS) analysis of the sliding surfaces revealed that the adsorption film derived from the succinimide on the sliding surfaces of the DLC-Si film and the mating steel ball also contributed to the sufficient and less sliding-velocity-dependant friction coefficients.     

Combination of DLC coatings and EP additives for improved tribological behaviour of boundary lubricated surfaces

The aim of the present investigation was to obtain some further understanding of the mechanism responsible for low-friction behaviour of W-containing DLC coatings (W-DLC) when lubricated with EP additivated oil. Boundary lubricated wear and friction tests were performed under reciprocating sliding motion using a high frequency test rig and a contact pressure of 1.5 GPa. Additionally, some of the tests were performed in a load-scanning reciprocating test rig, with the contact pressure being in the range from 2.4 to 5.6 GPa. The influence of concentration of a sulphur-based EP additive on the friction behaviour was investigated.This investigation showed that W-DLC coatings greatly improve the tribological properties of boundary-lubricated surfaces, especially when pairing coated and uncoated steel surfaces. The improved tribological behaviour was found to be governed by the gradual formation of a WS₂ type tribofilm on the steel counter-face or on revealed steel substrate. The friction level depends on the additive concentration.     

Tribological Characteristics of Rubber-Based Friction Materials

This article deals with the rubber-based friction materials (RBFMs) which can be used in brake system. The physico-mechanical and tribological properties of a series of fiber filled RBFMs containing steel wool and aramid pulp at different concentrations along with a fiber-free reference material were characterized. Rubber–glass transition induced at higher sliding velocities was identified based on the friction fade behavior of the RBFMs. The rubber–glass transition which is inherently originated by viscoelastic response of polymeric binder was found to be influential on the tribological properties of the RBFMs. It was revealed that steel wool increased coefficient of friction (COF) and improved friction recovery behavior at low volume percent (7.5 vol.%) but it aggravated the COF at high concentration of steel wool (15 vol.%) and severe sliding conditions because of harsh abrasive mechanism. Aramid pulp improved the fade behavior at high sliding velocities and increased COF due to formation of sticky contact patches. It was revealed that steel wool increased the wear rate while aramid pulp did not affect the wear rate significantly, contrary to the increase in the friction coefficient of RBFM. SEM analysis was proved to be useful in correlating the wear rates of composites to the topographical changes on the worn surfaces.     

A comparison of the tribological behaviour of steel/steel, steel/DLC and DLC/DLC contacts when lubricated with mineral and biodegradable oils

Diamond-like carbon (DLC) coatings, which can nowadays be applied to many highly loaded mechanical components, sometimes need to operate under lubricated conditions. It is reasonable to expect that in steel/DLC contacts, at least the steel counter body will behave according to conventional lubrication mechanisms and will interact with lubricants and additives in the contact. However, in DLC/DLC contacts, such mechanisms are still unclear. For example, the “inertness” of DLC coatings raises several questions about whether they are able to provide real boundary “lubrication” or whether they are just a “passive” member in these contacts. On the other hand, biodegradable oils, in particular vegetable base oils, possess a good lubricating ability, often much better than mineral or conventional synthetic oils as a result of the large amount of un-saturated and polar components that can promote the lubricity of DLC coatings. Accordingly, in this study, we present the results of experiments under severe boundary-lubrication conditions during reciprocating sliding. We look at the effect of the type of mating surfaces - steel/DLC, DLC/DLC and steel/steel - and the type of oil on the tribological performance of DLC coatings. We compare the wear and friction behaviours of two types of DLC coatings, i.e., a “pure” non-doped a-C:H DLC coating (denoted as a-DLC) and a WC-containing multilayer coating (denoted as W-DLC) tested with a mineral oil and a biodegradable vegetable oil. These oils, which have very different chemical compositions, were used as base oils and also with mild AW and strong EP additives. Among other things, the results confirm the following: (1) coating/coating lubricated contacts can resemble metal-lubrication mechanisms; (2) additives reduce wear in coating/coating contacts by up to 80%; (3) better wear and friction performance are obtained with oils that contain large amounts of polar and un-saturated molecules; (4) a coating/coating combination generally results in less wear than a steel/coating combination.     

Film Forming and Friction Properties of Overbased Calcium Sulphonate Detergents

The film-forming and friction properties of overbased calcium sulphonate (OBCaSu) detergents in rolling–sliding, thin film, lubricated contact have been investigated. All of the commercial detergents studied form thick, solid-like, calcium carbonate films on the rubbed surfaces, of thickness 100–150 nm. The films have a pad-like structure, interspersed by deep valleys in which practically no film is present. These films have the effect of increasing friction in intermediate speed conditions, an effect which is believed to occur because the pad structure of the film inhibits fluid entrainment and thus postpones the formation of an EHD film to higher entrainment speeds. Large differences were noted between the boundary friction coefficients of the various detergents tested. Two of them gave very low boundary friction coefficients, in the range 0.06–0.08, while the other two gave considerably higher friction. These differences are believed to originate from differences in the structures of the alkyl chains in the sulphonate detergent molecules. The films formed by OBCaSu detergents can be removed very effectively by treatment with EDTA solution and this shows that the films are effective in preventing wear.