A study on friction and wear characteristics of nanometer Al2O3 /PEEK composites under the dry sliding condition

The friction and wear properties of the polyetheretherketone (PEEK) based composites filled with 5 mass% nanometer or micron Al₂O₃ with or without 10 mass% polytetrafluroethylene (PTFE) against the medium carbon steel (AISI 1045 steel) ring under the dry sliding condition at Amsler wear tester were examined. A constant sliding velocity of 0.42 m s⁻¹ and a load of 196 N were used in all experiments. The average diameter 250 μm PEEK powders, the 15 or 90 nm Al₂O₃ nano-particles or 500 nm Al₂O₃ particles and/or the PTFE fine powders of diameter 50 μm were mechanically mixed in alcohol, and then the block composite specimens were prepared by the heat compression moulding. The homogeneously dispersion of the Al₂O₃ nano-particles in PEEK matrix of the prepared composites was analyzed by the atomic force microscopy (AFM). The wear testing results showed that nanometer and micron Al₂O₃ reduced the wear coefficient of PEEK composites without PTFE effectively, but not reduced the friction coefficient. The filling of 10 mass% PTFE into pure PEEK resulted in a decrease of the friction coefficient and the wear coefficient of the filled composite simultaneously. However, when 10 mass% PTFE was filled into Al₂O₃/ PEEK composites, the friction coefficient was decreased and the wear coefficient increased. The worn scars on the tested composite specimen surfaces and steel ring surfaces were observed by scanning electron microscopy (SEM). A thin, uniform, and tenacious transferred film on the surface of the steel rings against the PEEK composites filled with 5 mass% 15 nm Al₂O₃ particles but without PTFE was formed. The components of the transferred films were detected by energy dispersive spectrometry (EDS). The results indicated that the nanometer Al₂O₃ as the filler, together with PEEK matrix, transferred to the counterpart ring surface during the sliding friction and wear. Therefore, the ability of Al₂O₃ to improve the wear resistant behaviors is closely related to the ability to improve the characteristics of the transfer film.     

A Study on the Sliding Wear of Hybrid PTFE/Kevlar Fabric/Phenolic Composites Filled with Nanoparticles of TiO2 and SiO2

TiO₂ and SiO₂ nanoparticles were introduced into hybrid polytetrafluoroethylene (PTFE)/Kevlar fabric/phenolic composites. The results showed the incorporation of TiO₂ nanoparticles can reduce the wear rate of the fabric/phenolic composite at elevated temperatures, although the wear of hybrid PTFE/Kevlar fabric/phenolic composite did not change much when TiO₂ or SiO₂ nanoparticles were used as filler. The wear behavior was explained in terms of morphology of transfer films and worn surfaces. There was a good correlation between the morphology of transfer film and wear results.     

Tribological Behavior of PTFE Composites Filled with PEEK and Nano-Al2O3

In this study, the tribological properties of polytetrafluoroethylene (PTFE) composites filled with polyetheretherketone (PEEK) and nano-Al₂O₃ particles were studied using a block-on-ring wear tester. The tribological performance of the composites was affected by the experimental parameters (sliding speed, normal load, and environmental temperature) and the composites achieved a high-speed sliding friction state. The results showed that the PEEK and nano-Al₂O₃ particles significantly improved the wear resistance of the PTFE composites. In addition, the nano-Al₂O₃ particles increased the hardness of the composites and enhanced the mechanical properties to enable applications in a wider range of industrial fields. The effects of the sliding speed and normal load on the tribological properties were more significant than that of the environmental temperature. In addition, the entire wear process was divided into three stages (the initial wear stage, severe wear transition stage, and ultralow stable wear stage), according to the evolution of the tribological characteristics (wear rate, morphology of the worn surface and transfer film, and wear debris morphology).     

Tribological properties of ZrO2 (Y2O3)-Mo-BaF2/CaF2 composites at high temperatures

ZrO₂ (Y₂O₃) with different contents of BaF₂/CaF₂ and Mo were fabricated by hot pressed sintering, and the tribological behavior of the composites against SiC ceramic was investigated from room temperature to 1000 °C. It was found that the ZrO₂ (Y₂O₃)-5BaF₂/CaF₂-10Mo composite possessed excellent self-lubricating and anti-wear properties. The low friction and wear were attributed to enhanced matrix and BaMoO₄ formed on the worn surfaces.     

Tribological properties of spark-plasma-sintered ZrO2(Y2O3)-CaF2-Ag composites at elevated temperatures

Spark-plasma sintering is employed to synthesize self-lubricating ZrO₂(Y₂O₃) matrix composites with different additives of CaF₂ and Ag as solid lubricants by tailoring the composition and by adjusting the sintering temperature. The friction and wear behavior of ZrO₂(Y₂O₃) matrix composites have been investigated in dry sliding against an alumina ball from room temperature to 800 °C. The effective self-lubrication at different temperatures depends mainly on the content of various solid lubricants in the composites. The addition of 35 wt.% Ag and 30 wt.% CaF₂ in the ZrO₂(Y₂O₃) matrix can promote the formation of a well-covered lubricating film, and effectively reduce the friction and wear over the entire temperature range studied. The friction coefficients at low temperatures were at a minimum value for the composite containing 35 wt.% of silver. At this silver concentration, low and intermediate temperature lubricating properties are greatly improved without affecting high-temperature lubrication by the calcium fluoride in ZrO₂(Y₂O₃) matrix composites. The worn surfaces and transfer films formed during wear process have been characterized to identify the synergistic lubrication behavior of CaF₂ and Ag lubricants at different temperatures.     

High-temperature tribological properties of spark-plasma-sintered Al2O3 composites containing barite-type structure sulfates

Al₂O₃–50BaSO₄–20Ag, Al₂O₃–50BaSO₄–10SiO₂, Al₂O₃–50(mass%)SrSO₄, Al₂O₃–50PbSO₄–5SiO₂, Al₂O₃–50BaSO₄ and Al₂O₃–50BaCrO₄ composites (mass%) were prepared by spark plasma sintering and their microstructure and high-temperature tribological properties were evaluated. Al₂O₃–50BaSO₄–20Ag composites (mass%) showed the lowest friction coefficients at the temperature ranging from 473 to 1073 K. Thin Ag film was observed on the wear tracks of the composites above 473 K. In addition, the friction coefficients of Al₂O₃ composites containing SrSO₄ and PbSO₄ were as low as those of Al₂O₃–BaSO₄ and Al₂O₃–BaCrO₄ composites at the temperatures up to 1073 K. The thin films formed on the wear tracks of the Al₂O₃–SrSO₄ composites were composed of Al₂O₃ and SrSO₄ phases, while the films formed on the wear tracks of the Al₂O₃–PbSO₄–SiO₂ composites consisted of Al₂O₃, PbSO₄ and SiO₂ phases.     

The friction and wear properties of nanometre SiO2 filled polyetheretherketone

Nanometre SiO₂ filled-polyetheretherketone (PEEK) composite blocks with different filler proportions were prepared by compression moulding. Their friction and wear properties were investigated on a block-on-ring machine by running a plain carbon steel (AISI 1045 steel) ring against the composite block. The morphologies of the wear traces and the transfer film were observed by scanning electron microscopy (SEM). It was found that nanometre SiO₂ filled-PEEK exhibited considerably lower friction coefficient and wear rate in comparison with pure PEEK. The lowest wear rate was obtained with the composite containing 7.5 wt.% SiO₂. The SEM pictures of the wear traces indicated that with the frictional couple of carbon steel ring/composite block (fillec with 7.5 wt.% filler), a thin, uniform, and tenacious transfer film was formed on the ring surface. It was inferred that the transfer film contributed largely to the decreased friction coefficient and wear rate of the filled PEEK composites.     

Wear-Resistant PTFE/SiO2 Nanoparticle Composite Films

Polytetrafluoroethylene (PTFE) is a polymer that is well known for its exceptional tribological properties and, as such, it is commonly used to reduce the coefficient of friction between surfaces. In recent years it has also been established that by incorporating nanoparticle fillers in PTFE, it is possible to extend the polymer's life by reducing its wear rate. Although much study has been placed on bulk PTFE, very little study has been focused on thin films. This article demonstrates that SiO ₂ nanoparticles can be used as a filler to significantly reduce the wear of PTFE thin films while also maintaining a low coefficient of friction. The wear resistance and coefficient of friction of PTFE/SiO ₂ composite films on stainless steel substrates were tested using a linear reciprocating tribometer and compared to pure PTFE films and bare stainless steel to evaluate the benefit of incorporating the SiO ₂ filler in the film. The composite films showed a significant improvement in wear resistance when compared to pure PTFE films. The coefficient of friction for the composite film remained low and stable during a 50 g normal load friction test for a duration of approximately 300 cycles, whereas that of PTFE showed an increasing trend at onset. In addition, of 1.7 and 3.3 wt% SiO ₂ concentrations in solution, 3.3 wt% SiO ₂ showed better performance, with a much higher wear resistance than that of 1.7% SiO ₂ after being subjected to a 1,000-cycle abrasive wear test.     

Sliding wear characteristics of plasma-sprayed Al2O3 and Cr2O3 coatings against copper alloy under severe conditions

Al₂O₃ and Cr₂O₃ coatings were deposited by atmospheric plasma spraying and their tribological properties dry sliding against copper alloy were evaluated using a block-on-ring configuration at room temperature. It was found that the wear resistance of Al₂O₃ coating was superior to that of the Cr₂O₃ coating under the conditions used in the present study. This mainly attributed to its better thermal conductivity of Al₂O₃ coating, which was considered to effectively facilitate the dissipation of tribological heat and alleviate the reduction of hardness due to the accumulated tribological heat. As for the Al₂O₃ coating, the wear mechanism was plastic deformation along with some micro-abrasion and fatigue-induced brittle fracture, while the failure of Cr₂O₃ coating was predominantly the crack propagation-induced detachment of transferred films and splats spallation.     

Influence of Al2O3 reinforcement on the abrasive wear characteristic of Al2O3/PA1010 composite coatings

In the present study, the abrasive wear characteristics of Al₂O₃/PA1010 composite coatings were tested on the turnplate abrasive wear testing machine. Steel 45 (quenched and low-temperature tempered) was used as a reference material. The experimental results showed that when the Al₂O₃ particles have been treated with a silane coupling agent (γ-aminopropyl-triethoxysilane), the abrasive wear resistance of Al₂O₃/PA1010 composite coatings has a good linear relationship with the volume fraction of Al₂O₃ particles in Al₂O₃/PA1010 composite coatings and the linear correlation coefficient is 0.979. Under the experimental conditions, the size of Al₂O₃ particles (40.5-161.0 μm) has little influence on the abrasive wear resistance of Al₂O₃/PA1010 composite coatings. By treating the surface of Al₂O₃ particles with the silane coupling agent, the distribution of Al₂O₃ particles in PA1010 matrix is more homogeneous and the bonding state between Al₂O₃ particles and PA1010 matrix is better. Therefore, the Al₂O₃ particles make the Al₂O₃/PA1010 composite coatings have better abrasive wear resistance than PA1010 coating. The wear resistance of Al₂O₃/PA1010 composite coatings is about 45% compared with that of steel 45.     

Friction and wear behaviour of plasma-sprayed Cr2O3 coatings against steel in a wide range of sliding velocities and normal loads

This study investigates the influence of sliding speed and normal load on the friction and wear of plasma-sprayed Cr₂O₃ coatings, in dry and lubricated sliding against AISI D2 steel. Friction and wear tests were performed in a wide speed range of 0.125–8 m/s under different normal loads using a block-on-ring tribometer. SEM, EDS and XPS were employed to identify the mechanical and chemical changes on the worn surfaces. A tangential impact wear model was proposed to explain the steep rising of wear from the minimum wear to the maximum wear. The results show that the wear of Cr₂O₃ coatings increases with increasing load. Secondly, there exist a minimum-wear sliding speed (0.5 m/s) and a maximum-wear sliding speed (3 m/s) for a Cr₂O₃ coating in dry sliding. With the increase of speed, the wear of a Cr₂O₃ coating decreases in the range 0.125–0.5 m/s, then rises steeply from 0.5 m/s to 3 m/s, followed by a decrease thereafter. The large variation of wear with respect to speed can be explained by stick-slip at low speeds, the tangential impact effect at median speeds and the softening effect of flash temperature at high speeds. Thirdly, the chemical compositions of the transfer film are a-Fe₂O₃ in the speed range 0.25–2 m/s, and FeO at 7 m/s. In addition, the wear mechanisms of a Cr₂O₃ coating in dry sliding versus AISI D2 steel are adhesion at low speeds, brittle fracture at median speeds and a mixture of abrasion and brittle fracture at high speeds. Finally the lubricated wear of Cr₂O₃ coating increases sharply from 1 to 2.8 m/s.     

Friction and wear behaviour of Thordon XL and LgSn80 in sliding against plasma-sprayed Cr2O3 coatings

This paper studies the friction and wear behaviour of two important bearing materials, Thordon XL and LgSn80, in dry and lubricated sliding vs. plasma-sprayed Cr₂O₃ coatings. As a reference, AISI 1043 steel is also studied under the same conditions. SEM, EDS and surface topography were employed to study the wear mechanisms. The results indicate that the Thordon XL/Cr₂O₃ coating pair gives the lowest dry friction coefficient (0.16) under a normal load of 45.3 N (pressure 0.453 MPa) at a velocity of 1 m/s. The dry friction coefficient of Thordon XL/Cr₂O₃ coating increases to 0.38 under a normal load of 88.5 N (pressure 0.885 MPa). The dry friction coefficients of the LgSn80/Cr₂O₃ coating are in the range of 0.31–0.46. Secondly, both dry wear rate under low normal load (45.3 N) and lubricated wear rate under a load of 680 N for Thordon XL are lower than those of LgSn80 in sliding against plasma-sprayed Cr₂O₃ coatings at a speed of 1 m/s. However, under a normal load of 88.5 N the dry wear rate of Thordon XL is much higher than that of LgSn80. Thirdly, a high viscosity lubricant (SAE 140) leads to lower wear for Thordon XL and LgSn80 than a low viscosity lubricant (SAE 30). Finally, the dominating wear mechanism for Thordon XL is shear fracture when against the plasma-sprayed Cr₂O₃ ceramic coating. For LgSn80 against plasma-sprayed Cr₂O₃ ceramic coating, abrasive wear is the governing failure mechanism.     

Microstructure and High-Temperature Frictional Wear Property of Mo-Based Composites Reinforced by Aluminum and Lanthanum Oxides

In this article, we developed Mo-based composites reinforced with aluminum and lanthanum oxides using a sol-gel method combined with a sintering process and researched the microstructure and frictional wear properties under high-temperature conditions. The microstructure of composites was characterized by α-Al₂O₃ and composite oxide (La_0.62Mo_0.38)AlO₃, which were uniformly distributed in the molybdenum matrix. The composite oxide (La_0.62Mo_0.38)AlO₃ was mainly attached to α-Al₂O₃. The interfaces of α-Al₂O₃/Mo and α-Al₂O₃/(La_0.62Mo_0.38)AlO₃ were well bonded. The α-Al₂O₃ refined the molybdenum grains, increased the relative density and hardness of Mo-based composites, and had an obvious effect on the frictional wear properties of the composites. With increasing α-Al₂O₃ content, the friction coefficient first increased and then decreased, and the wear weight loss decreased continuously. The wear failure mode varied from microcutting to fatigue with increasing α-Al₂O₃ content. The better wear resistance of Mo-based composites, compared to pure molybdenum, was mainly attributed to the characteristics of α-Al₂O₃, such as high microhardness, good morphology, well-bonded phase interface, and high hardness matrix due to the effects of α-Al₂O₃ reinforcement.     

Microstructural and Tribological Properties of A356 Al–Si Alloy Reinforced with Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Particles

In the present study, the effect of the Al₂O₃ particles (average size of 12 μm, 3 and 10 wt.%) reinforcement on the microstructure and tribological properties of Al–Si alloy (A356) was investigated. Composites were produced by applying compocasting process. Tribological properties of unreinforced alloy and composites were studied, using pin-on-disc tribometer, under dry sliding conditions at different specific loads and sliding speed of 1 m/s. Microhardness measurements, optical microscope and scanning electron microscope were used for microstructural characterization and investigation of worn surfaces and wear debris. During compocasting of A356 alloy, a transformation from a typical dendritic primary α phase to a non-dendritic rosette-like structure occurred. Composites exhibited better wear resistance compared with unreinforced alloy. Presence of 3 wt.% Al₂O₃ particles in the composite material affected the wear resistance only at specific loads up to 1 MPa. The wear rate of composite with 10 wt.% Al₂O₃ particles was nearly two order of the magnitude lower than the wear rate of the matrix alloy. Dominant wear mechanism for all materials was adhesion, with others mechanisms: oxidation, abrasion and delamination as minor ones.     

Tribological characteristics of low-pressure plasma-sprayed A12O3 coating from room temperature to 800 °C

The tribological characteristics of low-pressure plasma-sprayed (LPPS) Al₂O₃ coating sliding against alumina ball have been investigated from room temperature to 800 °C. These friction and wear data have been compared quantitatively with those of bulk sintered alumina to obtain a better understanding of wear mechanisms at elevated temperatures. The friction and wear of Al₂O₃ coating show a strong dependence on temperature, changing from a mild to a severe wear regime with the increase of temperature. The coefficient of friction at room temperature is approximately 0.17 to 0.42, depending on applied load. The tribochemical reaction between the coating surface and water vapor in the environment and the presence of the hydroxide film on the Al₂O₃ coating reduce the friction and wear at room temperature as contrasted to those of bulk sintered alumina. At intermediate temperatures, from 400 to 600 °C, the friction and wear behavior of Al₂O₃ coating depends on the inter-granular fracture and pull-out of Al₂O₃ grains. At above 700 °C, formation and deformation of fine grain layer, and abrasive wear in the form of removal of fine alumina grains further facilitate the friction and wear process of Al₂O₃ coating.     

Friction and wear behavior of hybrid glass/PTFE fabric composite reinforced with surface modified nanometer ZnO

Nano-ZnO was successfully grafted with 2,4-toluenediisocyanate (TDI) and β-aminoethyltrimethoxylsilane (OB551) to avoid the agglomeration of nano-ZnO in composite. The hybrid glass/PTFE fabric composites reinforced with the untreated, OB551 and TDI modified nano-ZnO, respectively, were prepared by dip-coating of the hybrid fabric in a phenolic adhesive resin containing the nanoparticles to be incorporated and the successive curing. The friction and wear behaviors of various nano-ZnO reinforced hybrid glass/PTFE fabric composites sliding against AISI-1045 steel in a pin-on-disk configuration were evaluated on a Xuanwu-III high-temperature friction and wear tester, with the unfilled one as a reference. The morphologies of the worn surfaces of the composites and of the counterpart pins were analyzed using scanning electron microscopy. In addition, FTIR spectrum was taken to characterize the untreated and treated nano-ZnO. It is found that the untreated and treated nano-ZnO reinforced hybrid glass/PTFE fabric composites exhibit improved wear resistance and friction-reduction in comparison with the unfilled one. The TDI modified nano-ZnO reinforced composite can obtain the best friction and wear performance under different applied load; followed by the OB551 modified nano-ZnO reinforced one. Sliding conditions, such as environmental temperature and lubricating condition, significantly affect the tribo-performances of the unfilled and filled hybrid glass/PTFE fabric composites.     

Tribological studies of glass fabric-reinforced polyamide composites filled with CuO and PTFE

The effect of glass fabric reinforcement on the friction and wear behavior of nylon was investigated for varying fabric proportions. The effect of the addition of particulate CuO filler, and the filler and PTFE to the glass fabric-reinforced composites on the tribological properties of the composites was also studied. The composites with different proportions of fiber, filler and PTFE were compression molded and tested for friction and wear in a pin-on-disk configuration. It was found that the proportion of glass fabric for optimum wear resistance was about 20% by volume. The addition of CuO filler did not contribute to improvement in the wear resistance of the fabric-reinforced composites because a good transfer film did not develop in the presence of fibers and the composites became fragile. PTFE was very effective in reducing the wear of filled and fabric-reinforced composites. The friction and wear behavior of these composites has been interpreted in terms of their ability to form transfer film on the steel counterface and the changes occurring on the pin surface. The composition for maximum wear resistance was 25 vol.% CuO-11.3 vol.% glass fabric-10 vol.% PTFE-nylon.     

Tribological behaviour of PTFE modified cotton polyester composites

Abstract

An attempt on modification of tribological behaviour of cotton polyester composite was done with polytetrafluoroethylene (PTFE). PTFE modified polyester–cotton composites were developed and studied for their friction and sliding wear behaviour at different applied loads. The sliding wear tests of composites were conducted against EN-31 steel counter face. The coefficient of friction μ as well as the sliding wear rate of cotton–polyester composites reduced significantly on addition of PTFE. The reduction in wear rate of PTFE modified polyester–cotton composite has been discussed with the help of SEM observations of worn surfaces and coefficient of friction.     

Tribological Behaviour of Nanostructured Al2O3-3 wt% TiO2 Coating Against Steel in Dry Sliding

Nanostructured and conventional Al₂O₃-3 wt% TiO₂ coatings were deposited by atmospheric plasma spraying. The wear and friction properties of both coatings against a steel ball under dry friction conditions were examined. It was found that the wear resistance of the nanostructured Al₂O₃-3 wt% TiO₂ coating was superior to that of the corresponding conventional counterpart. The improvement in wear resistance of the nanostructured coating was attributed to its higher toughness and cohesion strength between splats. As for the nanostructured coating, the wear mechanism was mainly adhesion with micro-abrasion at low loads (20 N). At high loads (80 N), the wear of the nanostructured coating was controlled by plastic deformation and associated delamination along the splat boundaries, which was similar to that of the conventional coating at low loads. However, the failure of the conventional coating was predominantly brittle fracture within the splats and delamination between splats at high loads.     

The effect of Al2O3 on the friction performance of automotive brake friction materials

This study consists of two stages. In the first stage, bronze-based break linings were produced and friction-wear properties of them were investigated. In the second stage, 0.5%, 1%, 2% and 4% alumina (Al₂O₃) powders were added to the bronze-based powders and Al₂O₃ reinforced bronze-based break linings were produced. Friction–wear properties of the Al₂O₃ reinforced samples were aslo investigated and compared to those of plain bronze-based ones. For this purpose, friction coefficient and wear behaviour of the samples were tested on the grey cast iron disc. The hardness and density of the samples were also determined. Microstructures of the samples before and after the sintering and the worn surfaces of the wear specimens were examined using a scanning electron microscope (SEM). The sample compacted at 350 MPa and sintered at 820 °C exhibited the optimum friction–wear behaviour. With increase in friction surface temperature, a reduction in the friction coefficient of the samples was observed. The lowest reduction in the friction coefficient with increasing temperature was for the 2% and 4% Al₂O₃ reinforced samples. The SEM images of the sample indicated that increase in Al₂O₃ content resulted in adhesive wear. With increase in Al₂O₃ content, a reduction in mass loss of the samples was also observed. Overall, the samples reinforced with 2% and 4% Al₂O₃ exhibited the best results.