共查询到20条相似文献,搜索用时 125 毫秒
1.
Binary blends of a liquid crystalline polymer (LCP) and poly(ethylene 2,6-naphthalate) (PEN) were melt blended and injection molded. The mechanical properties were studied as a function of LCP content. Both the ultimate tensile strength and Young's modulus are higher than the theoretical values predicted by the rule of mixtures and they display a synergistic behavior at 70 wt % LCP content. However, the tensile strength decreases with LCP content and Young's modulus remained unchanged at lower LCP contents (10 to 30 wt %). The poor mechanical property is attributed to the immiscibility between PEN and LCP and the fibrillation behavior of LCP as revealed by differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) results. However, LCP and PEN are found to be partially miscible at higher LCP content, ascertained by DSC and dynamic mechanical analysis (DMA). This is attributed to the transesterification reaction between PEN and PET moiety in the LCP molecules. SEM micrographs reveal a skin/core morphology in the tensile bars, that is, the LCP is better oriented in the skin than in the core region. At lower LCP content, the dispersed LCP phase is spherical in the core and ellipsoidal in the skin, with long axes oriented in the flow direction. DSC studies show that the crystallization rate is significantly enhanced by the presence of LCP up to 50 wt %, where the LCP acts as a nucleating agent for PEN crystallization. The melting temperature decreases with LCP content, probably as a result of imperfect crystals formed in the presence of LCP heterogeneous nucleating centers and the increasing miscibility between LCP and PEN. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 477–488, 2001 相似文献
2.
Blends of an amorphous polyamide (PA) and a liquid crystalline copolyesteramide (LCP), poly(naphthoate-aminophenoterephthalate) were prepared in a twin-screw extruder. Specimens for mechanical testing were prepared by injection molding. Morphological, thermal, mechanical, and rheological properties were investigated by scanning electron microscopy (SEM), differential scanning calorimetry (DSC), X-ray diffractometry, capillary rheometry, and a tensile tester, respectively. The tensile mechanical behavior of the LCP/PA blends was found to be affected by their compositions and specimen thickness. Tensile testing revealed that the tensile mechanical behavior of the LCP/PA blends was very similar to that of polymeric composite and the tensile strength of the LCP/PA (50/50) blend was approximately two times of the value of PA homopolymer and exceeded that of pure LCP. The morphology of the LCP/PA blends was also found to be affected by their compositions. SEM studies revealed that the liquid crystalline polymer (LCP) formed finely dispersed spherical domains in the PA matrix and the inclusions were deformed into fibrils from the spherical droplets with increasing LCP content. It has been found that droplet and fiber formations lead to low and high strength material, respectively. In particular, at specific LCP content (50 wt%), the tensile strength of the LCP/PA blend exceeded that of pure LCP. The improvement in tensile properties is likely due to the reinforcement of the PA matrix by the fibrous LCP phase as observed by SEM. A distinct shell-core morphology was found to develop in the injection molded samples of these blends. This is believed to have a synergistic effect on the tensile properties of the LCP/PA blends. The rheological behavior of the LCP/PA blends was found to be very different from that of the parent polymers and significant viscosity reductions were observed for the LCP/PA (50/50) blend. Based upon DSC, these blends have shown to be incompatible in the entire range of concentrations. 相似文献
3.
Blends of a poly(ethylene 2,6-naphthalate) (PEN) and a liquid crystalline copolyester (LCP), poly(benzoate-naphthoate) were prepared in a twin-screw extruder. Specimens for thermal properties were investigated by means of an instron capillary rheometer (ICR) and scanning electron microscopy (SEM). The blend viscosity showed a minimum at 10 wt% of LCP and increased with increasing LCP content above 10 wt% of LCP. Above 50% of LCP and at higher shear rate, phase inversion occured and the blend morphology was fibrous and similar to pure LCP. The ultimate fibrillar structure of LCP phase appeared to be closely related to the extrusion temperature. By employing a suitable deformation history, the LCP phase may be elongated and oriented such that a microfibrillar morphology can be retained in the solid state. Thermal properties of the LCP/PEN blends were studied using DSC and a Rheovibron viscoelastomer. These blends were shown to be incompatible in the entire range of the LCP content. For the blends, the Tg and Tm were unchanged. The half time of crystallization for the LCP/PEN blends decreased with increasing LCP content. Therefore, the LCP acted as a nucleating agent for the crystallization of PEN. The dimensional and thermal stability of the blends were increased with increasing LCP content. In studies of dynamic mechanical properties, the storage modulus (E′) was improved with increasing LCP content and synergistic effects were observed at 70 wt% of LCP content. The storage modulus for the LCP/PEN 70/30 blend is twice that of PEN matrix and exceeded pure LCP. 相似文献
4.
Structural, rheological, and mechanical properties of ternary blends of a liquid crystalline copolyester (LCP) composed of p-hydroxybenzoic acid and 2,6-hydroxynaphthoic acid, poly(ehtylene naphthalate)(PEN), and poly(ethylene terephtalate) (PET) were investigated using capillary rheometry, tensile testing, scanning electron microscopy, and X-ray diffraction. Viscosity-shear rate behavior of the ternary blends is very similar to that of pure polymers and their binary blends. The activation energy of flows of the ternary blends was smaller than those of PEN and PET. Tensile modulus and strength of extruded strands of the blends increased with increasing LCP content. The extruded strands of the blends consist of a crystalline and oriented LCP phase and an amorphous and unoriented PEN/PET blended phase. Tensile mechanical properties and structures of the ternary blends were discussed. 相似文献
5.
Ternary in‐situ poly(butylene terephthalate) (PBT)/poly(acrylonitrile‐butadienestyrene) (ABS)/liquid crystalline polymer(LCP) blends were prepared by injection molding. The LCP used was a versatile Vectra A950, and the matrix material was PBT/ABS 60/40 by weight. Maleic anhydride (MA) copolymer and solid epoxy resin (bisphenol type‐A) were used as compatibilizers for these blends. The tensile, dynamic mechanical, impact, morphology and thermal properties of the blends were studied. Tensile tests showed that the tensile stregth of PBT/ABS/LCP blend in the longitudinal direction increased markedly with increasing LCP content. However, it decreased sharply with increasing LCP content up to 5 wt%; thereafter it decreased slowly with increasing LCP content in the transverse direction. The modulus of this blend in the longitudinal direction appeared to increase considerably with increasing LCP content, whereas the incorporation of LCP into PBT/ABS blends had little effect on the modulus in the transverse direction. The impact tests revealed that the Izod impact strength of the blends in longitudinal direction decreased with increasing LCP content up to 10 wt%; thereafter it increased slowly with increasing LCP. Dynamic mechanical analyses (DMA) and thermogravimetric measurements showed that the heat resistance and heat stability of the blends tended to increase with increasing LCP content. SEM observation, DMA, and tensile measurement indicated that the additions of epoxy and MA copolymer to PBT/ABS matrix appeared to enhance the compatibility between PBT/ABS and LCP. 相似文献
6.
Blends of a polyester elastomer (PEL) having a hard segment of polyester (PBT) and soft segment of polyether (PTMG) and a liquid crystalline copolyester (LCP), poly(benzoate-naphthoate), were prepared in a twin-screw extruder. Specimens for mechanical testing were prepared by injection molding. The morphology of the LCP/PEL blends was characterized under different processing conditions. To determine what conditions were necessary for the development of a fibrillar morphology of LCP, we have studied the effect of processing method (extrusion and injection molding), injection molding temperature (below and above the melting point of LCP), and gate position in the mold (direct gate and side gate). SEM studies revealed that some extensional flow was required for the fibrillar formation of LCP and the fibrillar structure of LCP was controlled by the processing method. The morphology of the blends was found to be affected by their compositions and processing conditions. SEM studies revealed that finely dispersed spherical domains of LCP were formed in the PEL matrix and the inclusions were deformed in fibrils from the spherical droplets with increasing LCP content and injection temperature. The mechanical properties of the LCP/PEL blends were also found to be affected by their compositions and processing conditions. The mechanical properties of LCP/PEL blends were very similar to those of polymeric composite. An attempt was made to correlate the structure of the blends from the scanning electron microscope with the measured mechanical properties. All of the aspects of the morphology were possible to explain in terms of the mechanical properties of the blends. A DSC study revealed that the crystallization of PEL was accelerated by the addition of LCP in the matrix and a partial compatibility between LCP and PEL was predicted. The rheological behavior of the LCP/PEL blends was found to be very different from that of the parent polymers, and significant viscosity reductions were observed in the blend consisting of only 5 wt% of LCP. 相似文献
7.
Jin-Hae Chang Bong-Ku Choi Jae-Hoon Kim Soo-Min Lee Myung-Sik Bang 《Polymer Engineering and Science》1997,37(9):1564-1571
A thermotropic liquid crystalline polymer (LCP) with an alkyl side-group was synthesized. Blends of the LCP with polycarbonate (PC) were prepared by coprecipitatton from a common solvent. The rheological behavior of the LCP/PC blends was found to be very different from that of PC, and significant viscosity reductions were observed in the temperature range of 200–230°C. Blends of different LCP compositions were extruded with different draw ratio from a capillary rheometer. The ultimate tensile strength showed a maximum at a 10 wt% LCP composition in the blends. It decreased for compositions greater the 10 wt% LCP, whereas the initial modulus increased with increasing LCP content. The morphology of the blends was found to be affected by their compositions. Scanning electron microscopy (SEM) studies revealed finely dispersed spherical LCP domains in the PC matrix. The SEM micrographs also showed a poor adhesion between the two phases. 相似文献
8.
The in situ composites based on poly(ethylene 2,6‐naphthalate) (PEN) and liquid crystalline polymer (LCP) were investigated in terms of thermal, rheological, and mechanical properties, and morphology. Inclusion of LCP enhanced the crystallization rate and tensile modulus of the PEN matrix, although it decreased the tensile strength in the PEN‐rich phase. The orientation effect of this blend system was composition and spin draw ratio dependent, which was examined by Instron tensile test. Further, the addition of dibutyltindilaurate (DBTDL) as a reaction catalyst was found to increase the viscosity of the blends, enhance its adhesion between the dispersed LCP phases and matrix, and led to an increase of mechanical properties of two immiscible blends. Hence DBTDL is helpful in producing a reactive compatibilizer by reactive extrusion at the interface of this LCP reinforced polyester blend system. The optimum catalyst amount turned out to be about 500 ppm, when the reaction proceeded in the 75/25 PEN/LCP blend system. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2448–2456, 1999 相似文献
9.
The microstructures, mechanical properties, and fracture toughness of LCP (Vectra B950) reinforced PC/PBT blend with a 60/40 weight ratio have been studied. LCP of varying concentrations were investigated as rigid fillers in matrices of multiphase polymer blends. In this study, differences in microstructures and morphology between samples of two thicknesses (4 mm thick and 6 mm thick) and two geometries (dumbbell and rectangular) were compared using scanning electron microscopy (SEM). Given identical processing conditions, fibrous LCP structures were evident in the 4-mm-thick injection molded, dumbbell-shaped samples, whereas the 6-mm-thick rectangular samples displayed spherical dispersion of LCP aggregates that embrittled the preblended ductile matrix. Tensile properties of the dumbbell specimens showed superior strengthening and stiffening whereby the tensile strength increased twofold and the modulus increased fourfold. Plane strain fracture toughness was slightly enhanced as the LCP content increased because of the fiber strengthening effect but the overall fracture performance of the in situ composites was relatively poor compared with PC/PBT. Experimental results were compared with those predicted in composite theory. Simplified micromechanics equations were developed to describe the tensile moduli of injection molded LCP reinforced blends that exhibited a strong skin-core morphology. 相似文献
10.
Blends of phenolphthalein poly(ether ether ketone) and a thermotropic liquid crystalline copolyester
Blends of phenolphthalein poly(ether ether ketone) (PEK-C) and a thermotropic liquid crystalline copolyester (LCP), poly[(1-phenylethyl-p-phenylene terephthalate)-co-(1-cumyl-p-phenylene terephthalate)], was prepared via melt mixing. The studies of differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) indicate that the PEK-C/LCP blends display two glass transition temperatures which correspond to those of PEK-C- and LCP-rich phases, respectively. The PEK-C/LCP blends were judged to be partially miscible. Scanning electron microscopy (SEM) was employed to examine the morphology of the blends, and it was observed that all the PEK-C/LCP blends displayed a phase-separated structure. The interface between the PEK-C- and LCP-rich phases is poor. The Young's modulus of the PEK-C/LCP blends was found to increase with LCP content due to the high modulus of the LCP. However, the tensile strength and the elongation at break of the blends greatly decreases with increase of LCP content, owing to the poor interfacial adhesion. From the thermogravity analysis (TGA), it was observed that all the blends exhibited a two-step weight loss mechanism, and the thermal degradation onset temperature of the blends was lowered with the addition of LCP content. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1923–1931, 1998 相似文献
11.
Fumihiko Yazaki Atsushi Kohara Ryutoku Yosomiya 《Polymer Engineering and Science》1994,34(14):1129-1136
Polymer blends of polyethersulfone (PES) with an all aromatic liquid crystalline co-polyester (LCP) were investigated. In addition, PES oligomers with the reactive functions end groups (?ONa) were added as a third component to the above blends in order to improve their properties. Flexural properties, such as modulus and strength, and dynamic viscoelastic properties, such as dynamic storage elasticity (E′) and loss tangent (tan δ), of the blends were measured. The morphology of blends was characterized using a differential scanning calorimeter (DSC) and a scanning electron microscope (SEM). Of the flexural properties, the modulus of PES increased almost linearly with increasing LCP content. However, strength decreased as LCP content increased to 20 wt%. In contrast, the addition of the PES oligomers had little effect on modulus, but strength was clearly improved. Regarding dynamic viscoelastic properties, the oligomer-containing blends exhibited complex behavior. Regarding morphologies, SEM analysis revealed that the LCP was not fibrous in the core of the blend containing 40 wt% or less, but the addition of the PES oligomers made LCP fibrous even in blends with low LCP content. It was concluded that the PES oligomers with reactive functional groups acted as a compatibilizer in polymer blends of PES/LCP. 相似文献
12.
In situ reinforcement of poly(butylene terephthalate) and butyl rubber by liquid crystalline polymer
S. Kumar T. Rath R.N. Mahaling C.K. Das R.B. Srivastava S.B. Yadaw 《Polymer Composites》2009,30(5):655-664
Ternary in situ butyl rubber (IIR)/poly(butylene terephthalate) (PBT) and liquid crystalline polymer (LCP) blends were prepared by compression molding. The LCP used was a versatile Vectra A950, and the matrix material was IIR/PBT 50/50 by weight. Morphological, thermal, and mechanical properties of blends were investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM), differential scanning calorimetry, and thermogravimetric analysis (TGA). Microscopy study (SEM) showed that formation of fibers is increasing with the increasing amount of LCP A950. Microscopic examination of the fractured surface confirmed the presence of a polymer coating on LCP fibrils. This can be attributed to some interactions including both chemical and physical one. The increased compatibility in polymer blends, consisting of IIR/PBT, by the presence of LCP A950 may be explained by the adsorption phenomena of the polymer chains onto the LCP fibrils. SEM and AFM images provided the evidence of the interaction between IIR/PBT and the LCP. Dynamic mechanical analyses (DMA) and TGA measurements showed that the composites possessed a remarkably higher modulus and heat stability than the unfilled system. Storage modulus for the ternary blend containing 50 wt% of LCP exhibits about 94% increment compared with binary blend of IIR/PBT. From the above results, it is suggested that the LCP A950 can act as reinforcement agent in the blends. Moreover, the fine dispersion of LCP was observed with no extensional forces applied during mixing, indicating the importance of interfacial adhesion for the fibril formation. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers 相似文献
13.
The relationship between the microstructure developed during injection molding of liquid crystalline polymers (LCPs) containing blends and their mechanical properties, was studied. A wholly aromatic copolyester LCP was melt blended in various levels with polycarbonate (PC), poly(butylene terephthalate) (PBT), Nylon 6 (N-6), and amorphous nylon (AN). In all cases the LCP was the minor component. The resulting injection molded structure had a distinct skin core morphology, where elongated fibrous LCP particles comprised the skin layer and spherical and ellipsoidal ones composed the core section. The highest elongation and the finest diameter LCP fibrils were obtained with AN/LCP system, followed by PC/LCP. PBT/LCP blends showed a coarser morphology, while N-6/LCP system did not correlate with the tensile moduli of the injection molded specimens. AN/LCP blends demonstrated the highest moduli values, consistent with the highest orientations observed using electron microscopy, followed by PC/LCP, PBT/LCP, and N-6/LCP. Finally, tensile strength levels were correlated with both orientation levels and interfacial adhesion between the polyblend components. AN/LCP that exhibited the highest orientation and good adhesion appearance gave the highest tensile strength values followed by PC/LCP, PBT/LCP, and N-6/LCP polyblends. 相似文献
14.
The rheology, morphology and properties of the composite systems of LCP, Vectra ATM 950 and Nylon 66 were investigated. The viscocity ratio of LCP and matrix has strong influence on their morphology. For LCP blends, the viscosity ratio of LCP is a critical factor in determining the blend morphology. The optical micrographs show that the good fibrillation can be achieved when the viscocity of the dispersed LCP phase is less than that of the Nylon 66 matrix at 310°C. The dispersed LCP domains tend to be spherical or cluster‐like when the viscosity ratio of the disperesed LCP phase and the Nylon 66 matrix is more than 1 at 280°C. The scanning electron microscopy (SEM) and optical micrograph observations show that Nylon 66 is immiscible with LCP, and there are two distinct phases in the blends. The morphology of LCP phase changes with the composition. LCP exhibits a fine fibril dispersed phase in the Nylon 66 matrix in the low LCP concentration. With an increase in LCP concentration, the morphology of LCP phase is changed form a fine fibril dispersed phase to a perfectly aligned continuous fiber reinforced phase in the rich LCP concentration. The tensile moduli increase with LCP concentration, especially in the rich LCP concentration. The tensile strengths increase with LCP concentration only when LCP concentration is above 40 wt%. Compared to the pure Nylon 66 fiber, the 40 wt% LCP composite sample shows a 982.1% increase in tensile modulus and a 123.3% increase in tensile strength. The mechanical properties of composite fibers are below the rule of mixtures if the LCP concentration is low, but above the rule of mixtures if the LCP concentration is high. 相似文献
15.
Maleic anhydride compatibilized blends of isotactic polypropylene (PP) and thermotropic liquid crystaline polymer (LCP) were prepared either by the direct injection molding (one-step process), or by twin-screw extrusion blending, after which specimens were injection molded (two-step process). The morphology and mechanical properties of these injection molded in situ LCP composites were studied by means of scanning electron microscopy (SEM), Izod impact testing, static tensile, and dynamic mechanical measurements. SEM observations showed that fine and elongated LCP fibrils are formed in the maleic anhydride compatibilized in situ composites fabricated by means of the one-step process. The tensile strength and modulus of these composites were considerably close to those predicted from the rule of mixtures. Furthermore, the impact behavior of LCP fibril reinforced composites was similar to that of the glass fiber reinforced polymer composites. On the other hand, the maleic anhydride compatibilized blends prepared from the two-step process showed lower mechanical performance, which was attributed to the poorer processing behavior leading to the degradation of PP. The effects of the processing steps, temperatures, and compatibilizer addition on the mechanical properties of the PP/LCP blends are discussed. 相似文献
16.
Byoung Chul Kim Soon Man Hong Seung Sang Hwang Kwang Ung Kim 《Polymer Engineering and Science》1996,36(4):574-582
Ternary blends of poly(p-phenylenesulfide) (PPS), thermotropic liquid crystalline polyesteramide (LCP), and polysulfone (PSF) were investigated in terms of processing characteristics, blend morphology, and physical properties. In the incompatible PPS/LCP blends, LCP imparted a nucleating effect to the crystallization of PPS. Up to 10wt% LCP content, the tensile properties of PPS/LCP blends were enhanced with increasing LCP content, but they deteriorated if the LCP content exceeded 20wt%. Addition of a third component, PSF, to the 90/10 PPS/LCP blend promoted development of rodlike or threadlike fibrillar structure and orientation of the deformed LCP domains, which led to improvement of tensile strength up to 20%. 相似文献
17.
Poly(butylene adipate-co-terephthalate) (PBAT) is a soft biodegradable polymer with a low melting temperature. PBAT has been melt-blended with a liquid crystalline polymer (LCP) aiming at preparing a new biodegradable polymer blend with improved mechanical properties. The phase structure and crystalline morphologies of the PBAT/LCP blends were investigated using scanning electron microscopy (SEM), differential scanning calorimetry (DSC), small-angle X-ray scattering (SAXS), and transmission electron microscopy (TEM). It was found that the LCP domains are precisely dispersed in the PBAT matrix and that these domains act as the nuclei for PBAT crystallization. The nonisothermal crystallization temperature from the melt was dramatically shifted from 50°C to about 95°C by the addition of 20% LCP. In addition, the tensile modulus of the prepared blends increases gradually with increasing LCP content, indicating the excellent strengthening effects of LCP on the PBAT matrix. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008 相似文献
18.
A co‐polyester liquid crystalline polymer (LCP) was melt blended with an acrylonitrile–butadiene–styrene copolymer (ABS). LCP fibrils are formed and a distinct skin/core morphology is observed in the injection moulded samples. At higher LCP concentration (50 wt%), phase inversion occurs, where the dispersed LCP phase becomes a co‐continuous phase. While the tensile strength and Young's modulus remain unchanged with increasing LCP content up to 30 wt% LCP, a significant enhancement of the modulus at 50 wt% LCP is observed due to the formation of co‐continuous morphology. The blend modulus is lower than the values predicted by the rule of mixtures, suggesting a poor interface between the LCP droplets and ABS matrix. A copolymer of styrene and maleic anhydride (SMA) was added in the LCP/ABS blends during melt blending. It is observed that SMA has a compatibilizing effect on the blend system and an optimum SMA content exists for mechanical properties enhancement. SMA improves the interfacial adhesion, whereas excess of SMA reduces the LCP fibrillation. Copyright © 2003 Society of Chemical Industry 相似文献
19.
Fibers (strands) with various draw ratios were spun from the liquid crystalline state of a pure aromatic liquid crystalline copoly(ester amide) and the melts of its blend with polycarbonate. Scanning electron microscopy (SEM), wide angle X-ray scattering (WAXS), and differential scanning calorimetry (DSC) were employed to investigate the structure and properties of the resulting fibers. Mechanical properties of the fibers were also evaluated. It was found that both the crystallite size and heat of fusion of the liquid crystalline polymer (LCP) increase steadily with draw ratio. However, the crystal-nematic transition temperature of the LCP is virtually unaffected by drawing. Moreover, heat of fusion of LCP is much smaller than that of isotropic condensation polymers despite the presence of very sharp diffraction peaks in WAXS measurements. These results are ascribed to the (semi)rigid rod nature of the LCP chains and the persistence of an ordered structure in the LCP melt, i.e., entropy effect. It was further observed that tensile modulus and tensile strength along fiber axis rise with draw ratio for the composite fibers. The elastic modulus of the composite fibers were found to be as high as 19 GPa and tensile strength reached 146 MPa with draw ratios below 40 and an LCP content of 30 wt%. Compared with the thermoplastic matrix, the elastic modulus and tensile strength of the in-situ composite have increased by 7.3 times and 1.4 times, respectively, with the addition of only 30 wt% LCP. This improvement in mechanical properties is attributed to fibrillation of the LCP phase in the blend and the increasing orientation of the LCP chains along the fiber axis during drawing. 相似文献
20.
Blends of a thermotropic liquid crystalline polymer (LCP) with modified poly (phenylene oxide) (PPO) were injection molded. The morphology, tensile properties and dynamic mechanical behavior of the blends have been studied as a function of LCP content. Furthermore, the impact performance of these blends has been investigated by the instrumented Izod and Charpy falling weight tests. The critical strain energy release rate (GIC) of the blends were determined and the GIC values were found to be dependent on the LCP content. The results are discussed and explained in terms of materials morphology. 相似文献