A novel amperometric biosensor for oxalate determination using multi-walled carbon nanotube-gold nanoparticle composite

An amperometric oxalate biosensor using nanohybrid film of multi-walled carbon nanotubes (MWCNTs) and gold colloidal nanoparticles (GNPs) via carbodiimide chemistry by forming amide linkages between carboxylic acid groups on the CNTs and amine residues of cysteamine self-assembled monolayer (SAM) has been prepared. The c-MWCNTs were immobilized on the gold (Au) electrode and characterized by FTIR. The morphologies of the c-MWCNT/Au and GNPs/MWCNT/Au electrodes were investigated by scanning electron microscopy (SEM) and the electrochemical performance of the Au, c-MWCNT/Au and GNPs/c-MWCNT/Au electrodes were also studied amperometrically. The Cl⁻ and NO₃⁻ insensitive oxalate oxidase from grain sorghum was finally immobilized on this electrode. The influence of pH, temperature and oxalate concentration on electrode activity was studied. The electrode showed optimum response within 7 s. The electrocatalytic response showed a linear dependence on the oxalic acid concentration ranging from 1 to 800 μM with a detection limit of 1 μM. The K_m value for the oxalic acid sensor was 444.44 μM. The enzyme electrode retained 30% of its initial activity after 5 months, when stored at 4 °C. The electrode was employed for measurement of oxalic acid in serum, urine and foodstuffs.     

Layer-by-layer self-assembly CdTe quantum dots and molecularly imprinted polymers modified chemiluminescence sensor for deltamethrin detection

A novel chemiluminescence sensor for determination deltamethrin was firstly reported based on CdTe quantum dots and deltamethrin imprinted polymers by layer-by-layer assembly modified on the surface of slide glass, whose shape was the same as the bottom of 96 well micro-plate. The binding characteristic of the imprinted polymers to deltamethrin was evaluated by equilibrium binding experiments and the morphology was studied by scanning electronic microscope. Scatchard analysis was carried out to estimate the binding parameters of the imprinted polymers. The water-soluble TGA-capped CdTe quantum dots were prepared. NaHTe was used as the Te precursor for CdTe quantum dots synthesis. Under the optimum conditions, the chemiluminescence intensity had a linear relationship against the concentration of deltamethrin over the range of 0.053-46.5 μg mL⁻¹ with a lower detection limit of 0.018 μg mL⁻¹. The regression equation was ΔI = 2225 + 107c (c: μg mL⁻¹) with a correlation coefficient of 0.9973. The relative standard deviation was 4.7%. The presented method was applied successfully to the determination of deltamethrin in real samples with satisfactory results.     

Synthesis of Ag2Se nanomaterial by electrodeposition and its application as cataluminescence gas sensor material for carbon tetrachloride

In this paper, we presented a carbon tetrachloride gas sensor with strong cataluminescence response based on Ag₂Se nanomaterial, which was synthesized via the electrodeposition on the surface of Al foil by directly using a non-aqueous dimethyl sulfoxide (DMSO) solution with CH₃COOAg and SeCl₄. The deposited Ag₂Se material was characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Then, the prepared Ag₂Se material along with the Al foil substrate was employed to design the carbon tetrachloride gas sensor. Under the optimized conditions, the present gas sensor exhibited a broad linear range of 0.9-228 μg mL⁻¹, with a limit of detection of 0.3 μg mL⁻¹ (S/N = 3). The proposed gas sensor showed good characteristics with high selectivity, fast response and long lifetime.     

An electrochemical biosensor for determination of hydrogen peroxide using nanocomposite of poly(methylene blue) and FAD hybrid film

An electrochemical biosensor for determination of hydrogen peroxide (H₂O₂) has been developed by the hybrid film of poly(methylene blue) and FAD (PMB/FAD). The PMB/FAD hybrid film was performed in PBS (pH 7) containing methylene blue and FAD by cyclic voltammetry. Repeatedly scanning potential range of −0.6-1.1 V, FAD was immobilized on the electrode surface by electrostatic interaction while methylene blue was electropolymerized on electrode surface. This modified electrode was found surface confined and pH dependence. It showed good electrocatalytic reduction for H₂O₂, KBrO₃, KIO₃, and NaClO as well as electrocatalytic oxidation for NADH. At an applied potential of −0.45 V vs. Ag/AgCl, the sensor showed a rapid and linear response to H₂O₂ over the range from 0.1 μM to 960 μM, with a detection limit of 0.1 μM and a significant sensitivity of 1109 μA mM⁻¹ cm⁻² (S/N = 3). It presented excellent stability at room temperature, with a variation of response current less than 5% over 30 days.     

One-pot electrodeposition of 3-aminopropyltriethoxysilane-chitosan hybrid gel film to immobilize glucose oxidase for biosensing

We report on the electrodeposition of a 3-aminopropyltriethoxysilane-chitosan (APTES-CS) hybrid gel film for in situ immobilization of glucose oxidase (GOx) on an Au or platinized Au (Pt_nano/Au) electrode for biosensing of glucose. Controllable electroreduction of p-benzoquinone is used to lift the electrode-surface pH for the GOx-APTES-CS codeposition, which was monitored by an electrochemical quartz crystal microbalance. The fabrication procedures of the biosensor and the parameters influencing the biosensing performance were optimized. The prepared porous GOx-APTES-CS/Pt_nano/Au and GOx-APTES-CS/Au electrodes can be used to detect the enzymatically generated H₂O₂ at 0.5 and 0.7 V vs SCE, respectively. The enzyme electrodes exhibited linear responses to glucose concentration from 0.2 μM to 8.2 mM (R = 0.998, at Pt_nano/Au substrate) and from 0.2 μM to 5.5 mM (R = 0.998, at Au substrate), with current sensitivities of 69.5 (Pt_nano/Au) and 65 (Au) μA mM⁻¹ cm⁻², respectively, and a detection limit of 0.2 μM (S/N = 3) was achieved for each electrode. The response time was less than 5 (Pt_nano/Au) or 8 (Au) s. It is striking that the enzyme electrodes remained their initial response sensitivity after storage for 5 (Au) and >6 (Pt_nano/Au) months in 0.10 M PBS (pH 7.0) at 4 °C.     

An amperometric glucose biosensor based on layer-by-layer GOx-SWCNT conjugate/redox polymer multilayer on a screen-printed carbon electrode

An amperometric glucose biosensor based on a multilayer made by layer-by-layer assembly of single-walled carbon nanotubes modified with glucose oxidase (GOx-SWCNT conjugates) and redox polymer (PVI-Os) on a screen-printed carbon electrode (SPCE) surface was developed. The SPCE surface was functionalized with a cationic polymer by electrodeposition of the PVI-Os, followed by alternating immersions in anionic GOx-SWCNT conjugate solutions and cationic PVI-O solutions. The purpose is to build a multilayer structure which is further stabilized through the electrodeposition of PVI-Os on the multilayer film. The electrochemistry of the layer-by-layer assembly of the GOx-SWCNT conjugate/PVI-Os bilayer was followed by cyclic voltammetry. The resultant glucose biosensor provided stable and reproducible electrocatalytic responses to glucose, and the electrocatalytic current for glucose oxidation was enhanced with an increase in the number of bilayers. The glucose biosensor displayed a wide linear range from 0.5 to 8.0 mM, a high sensitivity of 32 μA mM⁻¹ cm⁻², and a response time of less than 5 s. The glucose biosensor proved to be promising amperometric detectors for the flow injection analysis of glucose.     

Catalytic determination of traces of Rh(III) using an optode based on immobilization of methyl violet on a triacetylcellulose membrane

The characterization of an optical sensor membrane is described for determination of rhodium. The optode sensing reagent is methyl violet which is immobilized on triacetylcellulose membrane. It has been found that oxidation of methyl violet with periodate is very slow. Presence of trace amount of Rh(III) catalyzes the reaction and causes a significant increase in the reaction rate. The reaction of periodate with the immobilized methyl violet in the presence of rhodium in acidic media causes a decrease in the absorbance of the film at 594 nm which is directly proportional to the concentration of rhodium. This sensing phase has a linear range of 1-110 μg mL⁻¹ for Rh(III) ions. The one-shot sensor can readily be fully regenerated with methyl violet solution, and the color is fully reversible.     

Electrochemical studies of bovine serum albumin immobilization onto the poly-o-phenylenediamine and carbon-coated nickel composite film and its interaction with papaverine

A biosensor based on bovine serum albumin (BSA) and poly-o-phenylenediamine (PoPD)/carbon-coated nickel (C-Ni) nanobiocomposite film modified electrode has been developed to study the interaction of BSA with papaverine (PAP). The well-dispersed C-Ni nanoparticles were dripped onto the glassy carbon electrode (GCE) surface firstly, and PoPD films were subsequently electropolymerized by cyclic voltammetry (CV) to prepare PoPD/C-Ni/GCE. Finally, the BSA was easily immobilized on the PoPD films via electrostatic adsorption. The morphology and the electrochemical properties of the fabricated composite electrodes were examined by scanning electron microscope (SEM) and electrochemical impedance spectroscopy (EIS), respectively. The interaction of PAP with BSA was monitored by differential pulse voltammetry (DPV), using PoPD as the electrochemical indicator. The binding constant (K), obtained by DPV, was 1.7 × 10⁴ L/mol, which was consistent with the fluorescence analysis. This constructed biosensor also exhibited a fine linear correlation with PAP concentration range of 2.5 × 10⁻⁹-4.5 × 10⁻⁵ mol/L and a detection limit of 8.3 × 10⁻¹⁰ mol/L was achieved by DPV.     

Fabrication of novel chitosan nanofiber/gold nanoparticles composite towards improved performance for a cholesterol sensor

A novel amperometric cholesterol biosensor was fabricated by the immobilization of ChOx (cholesterol oxidase) onto the chitosan nanofibers/gold nanoparticles (designated as CSNFs/AuNPs) composite network (NW). The fabrication involves preparation of chitosan nanofibers (CSNFs) and subsequent electrochemical loading of gold nanoparticles (AuNPs). Field emission scanning electron microscopy (FE-SEM) was used to investigate the morphology of CSNFs (sizes in the range of ∼50-100 nm) and spherical AuNPs. Cyclic voltammetry, hydrodynamic voltammetry and amperometry were used to examine the performance of CSNF-AuNPs/ChOx biosensor. The CSNF-AuNPs/ChOx biosensor exhibited a wide linear response to cholesterol (concentration range of 1-45 μM), good sensitivity (1.02 μA/μM), low response time (∼5 s) and excellent long term stability. The combined existence of AuNPs within CSNFs NW provides the excellent performance of the biosensor towards the electrochemical detection of cholesterol.     

Selective potentiometric determination of uric acid with uricase immobilized on ZnO nanowires

In this study, a potentiometric uric acid biosensor was fabricated by immobilization of uricase onto zinc oxide (ZnO) nanowires. Zinc oxide nanowires with 80-150 nm in diameter and 900 nm to 1.5 μm in lengths were grown on the surface of a gold coated flexible plastic substrate. Uricase was electrostatically immobilized on the surface of well aligned ZnO nanowires resulting in a sensitive, selective, stable and reproducible uric acid biosensor. The potentiometric response of the ZnO sensor vs Ag/AgCl reference electrode was found to be linear over a relatively wide logarithmic concentration range (1-650 μM) suitable for human blood serum. By applying a Nafion^® membrane on the sensor the linear range could be extended to 1-1000 μM at the expense of an increased response time from 6.25 s to less than 9 s. On the other hand the membrane increased the sensor durability considerably. The sensor response was unaffected by normal concentrations of common interferents such as ascorbic acid, glucose, and urea.     

A coral-like macroporous gold-platinum hybrid 3D electrode for enzyme-free glucose detection

We are introducing a macroporous Au-Pt hybrid 3D electrode to be used for enzyme-free glucose detection. The proposed hybrid electrode was fabricated with a three dimensional structure by electroplating platinum nanoparticles onto the surface of the coral-like macroporous Au. It was then physically analyzed by using field emission scanning electron microscopy (FESEM). The porosity and window pore size of the macroporous Au electrode were 50% and 100-300 nm, respectively. The diameters of the Pt nanoparticles ranged from 10 to 15 nm. Through cyclic voltammograms in a 1 M sulfuric acid solution, we confirmed that the hybrid electrode exhibited a much larger surface activation area with a roughness factor (RF) of 2024.7 than the macroporous Au electrode with a roughness of 46.07. The highly improved surface activation area was caused by the electroplated Pt nanoparticles. The hybrid electrode exhibited a much stronger electrocatalytic activity due to glucose oxidation than the macroporous Au electrode. At 0.4 V, it responded linearly to the glucose up to 20 mM in a neutral media with a detection limit of 0.025 mM and detection sensitivity of 39.53 μA mM⁻¹ cm⁻² without being affected by interfering species. It also showed a stable recovery response to the step changes of the glucose concentration.     

Screen-printed carbon electrode for choline based on MnO2 nanoparticles and choline oxidase/polyelectrolyte layers

This paper presents the amperometric biosensor that determines choline and cholinesterase activity using a screen printed graphite electrode. In order to detect H₂O₂ we have blanket modified the electrode material with manganese dioxide nanoparticles layer. Using layer-by-layer technique on the developed hydrogen peroxide sensitive electrode surface choline oxidase was incorporated into the interpolyelectrolyte nanofilm. Its ability to serve as a detector of choline in bulk analysis and cholinesterase assay was investigated. We examined the interferences from red-ox species and heavy metals in the blood and in the environmental sample matrixes. The sensor exhibited a linear increase of the amperometric signal at the concentration of choline ranging from 1.3 × 10⁻⁷ to 1.0 × 10⁻⁴ M, with a detection limit (evaluated as 3σ) of 130 nM and a sensitivity of 103 mA M⁻¹ cm⁻² under optimized potential applied (480 mV vs. Ag/AgCl). The biosensor retained its activity for more than 10 consecutive measurements and kept 75% of initial activity for three weeks of storage at 4 °C. The R.S.D. was determined as 1.9% for a choline concentration of 10⁻⁴ M (n = 10) with a typical response time of about 10 s. The developed choline biosensor was applied for butyrylcholinesterase assay showing a detection limit of 5 pM (3σ). We used the biosensor to develop the cholinesterase inhibitor assay. Detection limit for chlorpyrifos was estimated as 50 pM.     

Electrochemical behaviors and determination of isoniazid at ordered mesoporous carbon modified electrode

In this work, an electrochemical sensor based on ordered mesoporous carbon (OMC) for the amperometric detection of isoniazid was developed. OMC was dispersed in a solution of Nafion, and the suspension was modified onto the surface of glassy carbon (GC) electrode. Cyclic voltammetry and amperometry were used to investigate the electrochemical behaviors of isoniazid on Nafion-OMC modified electrode (Nafion-OMC/GC). The results indicate that OMC can facilitate the electrochemical oxidation of isoniazid with a great decrease of overpotential in pH 7.0 phosphate buffer solution. The proposed biosensor provides excellent performance towards the determination of isoniazid with a high sensitivity of 0.031 μA/μM, a low detection limit of 8.4 × 10⁻⁸ M and wide linear range from 1.0 × 10⁻⁷ M to 3.7 × 10⁻⁴ M at +0.20 V vs. Ag/AgCl. The method was successfully applied to the determination of isoniazid tablets with satisfying results. All the results suggest that Nafion-OMC/GC electrode is a potential candidate for a stable and efficient electrochemical sensor to detect isoniazid.     

Ultrasensitive immunosensing of tuberculosis CFP-10 based on SPR spectroscopy

An antigen (Ag), CFP-10, found in tissue fluids of tuberculosis (TB) patients may be an ultimate candidate for use as a sensitive TB marker with a sensing method for early simplified diagnosis of TB. In this study, chemical and optical optimizations were carried out using novel immuno-materials for establishment of a self-assembled surface plasmon resonance (SPR) optical immunosensor system for detection of CFP-10, which is valuable for pre-clinical work, prior to conduct of massive clinical observations. For creation of a simple sensing interface, a monoclonal antibody (anti-CFP-10) was immobilized directly on a gold surface, followed by blocking with cystamine. Orientation and accessibility of anti-CFP-10 were assessed by the selective binding of CFP-10. Recent results indicate that the reusability of the sensor chip adopting the cystamine method was found to be preferable to other immobilization methods. A linear relationship was well correlated between SPR angle shift and CFP concentrations in the range from 100 ng mL⁻¹ to 1 μg mL⁻¹. Modification of the SPR chip with antibody provides a simple experimental platform for investigation of isolated proteins under experimental conditions resembling those of their native environment.     

A stable sandwich-type amperometric biosensor based on poly(3,4-ethylenedioxythiophene)-single walled carbon nanotubes/ascorbate oxidase/nafion films for detection of L-ascorbic acid

In this paper, a stable sandwich-type amperometric biosensor based on poly(3,4-ethylenedioxythiophene) (PEDOT)-single walled carbon nanotubes (SWCNT)/ascorbate oxidase (AO)/Nafion films for detection of l-ascorbic acid (AA) was successfully developed. PEDOT-SWCNT nanocomposite and Nafion films were used as inner and outer films, respectively. AO was immobilized between these two films. The PEDOT-SWCNT nanocomposite films were characterized by electrochemical impedance spectroscopy and scanning electron microscopy. The influence of detection potential and temperature on the biosensor performance was examined in detail. Despite the multilayer configuration, the biosensor exhibited a relatively fast response (less than 10 s) and a linear range from 1 μM to 18 mM (a correlation coefficient of 0.9974). The sensitivity of the biosensor was found to be 28.5 mA M⁻¹ cm⁻². Its experimental detection limit was 0.7 μM (S/N = 3) and the apparent Michaelis-Menten constant (K_m) was calculated to be 18.35 mM. Moreover, the biosensor exhibited good anti-interferent ability and excellent long-term stability. All the results showed that such sandwich-type PEDOT-SWCNT/AO/Nafion films could provide a promising platform for the biosensor designs for AA detection.     

Fabrication of a novel electrochemiluminescence glucose biosensor using Au nanoparticles decorated multiwalled carbon nanotubes

Au nanoparticles (nanoAu) with an average diameter of 60 nm were decorated on the surface of multiwalled carbon nanotubes to prepare MWCNTs-nanoAu nano-hybrids. The MWCNTs-nanoAu nano-hybrids were cast on the surface of a glassy carbon electrode and were then further modified with a layer comprising glucose oxidase and chitosan to fabricate a novel electrochemiluminescence (ECL) glucose biosensor. The biosensor showed a remarkably improved electrocatalytic activity towards luminol oxidation and significant improvement in its ECL response. The proposed ECL biosensor exhibited excellent performance for glucose detection with a wide linear range (1-1000 μM), low detection limit (0.5 μM), excellent reproducibility (0.5%) and satisfactory selectivity.     

Photoelectrocatalytic regeneration of NADH at poly(4,4′-diaminodiphenyl sulfone)/nano TiO2 composite film modified indium tin oxide electrode

Herein we report the photoelectrocatalytic regeneration of NADH at poly(4,4′-diaminodiphenyl sulfone)/nano TiO₂ (PDDS/TiO₂) composite modified indium tin oxide (ITO) electrode. The PDDS film growth was confirmed through in situ electrochemical quartz crystal microbalance (EQCM) studies. The prepared PDDS/TiO₂ composite was characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD) studies. SEM and AFM results confirmed that TiO₂ nanoparticles size is between 130 and 180 nm. XRD results showed that TiO₂ nanoparticles are crystalline and belong to anatase phase. Electrochemical impedance spectroscopy (EIS) and light induced EIS results substantiate a rapid electron transfer process at PDDS/TiO₂ composite surface. Cyclic voltammetry (CV) results demonstrated that composite film showed excellent response to the photoelectrocatalytic regeneration of NADH. The photoelectrocatalytic oxidation of NADH at composite film surface irradiated for 5 min (optimized irradiation time) produced a notable enhancement in anodic peak current and it was 18-fold higher than that of PDDS film and several folds higher than that of TiO₂ and bare ITO electrodes. Further, composite film showed higher sensitivity of 124.1 μA μM⁻¹ for NADH. From Square wave voltammetry (SWV) results, sensitivity of the irradiated composite film was obtained as 0.252 μA nM⁻¹ of NADH. The linear concentration range was between 23 and 39 nM NADH respectively. Further, the composite film exhibits good selectivity towards NADH and no significant interference effect was observed even when 200-fold excess of ascorbic acid (AA), dopamine (DA) and uric acid (UA) coexist in the same supporting electrolyte solution.     

Rapid parallelized and quantitative analysis of five pathogenic bacteria by ITS hybridization using QCM biosensor

We developed a 2 × 5 model quartz crystal microbalance (QCM) DNA biosensor array for detection of five bacteria, which based on hybridization analysis of bacterial 16S-23S rDNA internal transcribed spacer (ITS) region. A pair of universal primers was designed for PCR amplification of the ITSs. The PCR products were analyzed by the biosensor. We used gold nanoparticles to amplify the frequency shift signals. Fifty clinical samples were detected by both the biosensor and conventional bacteria culture method. We found a linear quantitative relationship between frequency shift and logarithmic concentration of synthesized oligonucleotides or bacteria cells. The measurable concentration ranged from 10⁻¹² to 10⁻⁸ M for synthesized oligonucleotides and 1.5 × 10² to 1.5 × 10⁸ CFU/mL for bacteria. The 10⁻¹² M of synthesized oligonucleotides or 1.5 × 10² CFU/mL of Pseudomonas aeruginosa could be detected by the biosensor system. The detection could be completed within 5 h including the PCR amplification procedure. Compared with bacteria culture method, the detection sensitivity and specificity of the biosensor system were 94.12% and 90.91%, respectively. There was no significant difference between these two methods (P = 0.625 > 0.05). The biosensor system provides a rapid and sensitive method for parallelized and quantitative analysis of multiple pathogenic bacteria in clinical diagnosis.     

Potentiometric urea biosensor based on urease immobilized by an electrosynthesized poly(o-phenylenediamine) film with buffering capability

A simple and novel potentiometric biosensor for urea detection was prepared by employing an electrosynthesized polymer with buffering capability. It was obtained by deposition of a weighed amount of urease (Ur) at a glassy carbon (GC) electrode followed by immobilization by an electrosynthesized poly-o-phenylenediamine (PPD) film. An unconventional “upside-down” (UD) geometry was employed for the electrochemical cell. The response of GC/Ur/PPD sensor is linear with urea concentration in the range 10 μM to 1 mM (15 mV/mM, R² = 0.9999) due to buffering capability of PPD film, which represents a novel role of electrosynthesized polymers in their application to biosensors. At higher concentrations, the more common Nernstian response (28 mV/decade, R² = 0.9987) is observed. The sensor exhibits a sufficient sensitivity for practical determinations, rapid response and long term stability.