Fe2O3 modified thick films of nanostructured SnO2 powder consisting of hollow microspheres synthesized from pyrolysis of ultrasonically atomized aerosol for LPG sensing

Nanostructured hollow spheres of SnO₂ with fine nanoparticles were synthesized by ultrasonic atomization. Thick film gas sensors were fabricated by screen printing technique. Different surface modified films (Fe₂O₃ modified SnO₂) were obtained by dipping them into an aqueous solution (0.01 M) of ferric chloride for different intervals of time followed by firing at 500 °C. The structural and microstructural studies of the samples were carried out using XRD, SEM, and TEM. The sensing performance of pure and modified films was studied by exposing various gases at different operating temperatures. One of the modified sample exhibited high response (1990) to 1000 ppm of LPG at 350 °C. Optimum amount of Fe₂O₃ dispersed evenly on the surface_, adsorption and spillover of LPG on Fe₂O₃ misfits and high capacity of adsorption of oxygen on nanostructured hollow spheres may be the reasons of high response.     

Characterization and humidity sensing properties of Bi0.5Na0.5TiO3-Bi0.5K0.5TiO3 powder synthesized by metal-organic decomposition

Bi_0.5Na_0.5TiO₃-Bi_0.5K_0.5TiO₃ (BNT-BKT) powder is synthesized by a metal-organic decomposition method and characterized by field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). A humidity sensor, which is consisted of five pairs of Ag-Pd interdigitated electrodes and an Al₂O₃ ceramic substrate, is fabricated by spin-coating the BNT-BKT powder on the substrate. Good humidity sensing properties such as high response value, short response and recovery times, and small hysteresis are observed in the sensing measurement. The impedance changes more than four orders of magnitude within the whole humidity range from 11% to 95% relative humidity (RH) at 100 Hz. The response time and recovery time are about 20 and 60 s, respectively. The maximum hysteresis is around 4% RH. The results indicate that BNT-BKT powder is of potential applications for fabricating high performance humidity sensors.     

Nanostructured spinel ZnCo2O4 for the detection of LPG

Nanostrucutred spinel ZnCo₂O₄ (∼26-30 nm) was synthesized by calcining the mixed precursor (consisting of cobalt hydroxyl carbonate and zinc hydroxyl carbonate) in air at 600 °C for 5 h. The mixed precursor was prepared through a low cost and simple co-precipitation/digestion method. The transformation of the mixed precursor into nanostructured spinel ZnCo₂O₄ upon calcinations was confirmed by X-ray diffraction (XRD) measurement, thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and high resolution transmission electron microscopy (HRTEM). To demonstrate the potential applicability of ZnCo₂O₄ spinel in the fabrication of gas sensors, its LPG sensing characteristics were systematically investigated. The ZnCo₂O₄ spinel exhibited outstanding gas sensing characteristics such as, higher gas response (∼72-50 ppm LPG gas at 350 °C), response time (∼85-90 s), recovery time (∼75-80 s), excellent repeatability, good selectivity and relatively lower operating temperature (∼350 °C). The experimental results demonstrated that the nanostructured spinel ZnCo₂O₄ is a very promising material for the fabrication of LPG sensors with good sensing characteristics. Plausible LPG sensing mechanism is also discussed.     

Fabrication of N-type Fe2O3 and P-type LaFeO3 nanobelts by electrospinning and determination of gas-sensing properties

N-type Fe₂O₃ nanobelts and P-type LaFeO₃ nanobelts were prepared by electrospinning. The structure and micro-morphology of the materials were characterized by X-ray diffraction (XRD) and scanning of electron microscopy (SEM). The gas sensing properties of the materials were investigated. The results show that the optimum operating temperature of the gas sensors fabricated from Fe₂O₃ nanobelts is 285 °C, whereas that from LaFeO₃ nanobelts is 170 °C. Under optimum operating temperatures at 500 ppm ethanol, the response of the gas sensors based on these two materials is 4.9 and 8.9, respectively. The response of LaFeO₃-based gas sensors behaves linearly with the ethanol concentration at 10-200 ppm. Sensitivities to different gases were examined, and the results show that LaFeO₃ nanobelts exhibit good selectivity to ethanol, making them promising candidates as practical detectors of ethanol.     

Sprayed CdIn2O4 thin films for liquefied petroleum gas (LPG) detection

Nanocrystalline cadmium indium oxide (CdIn₂O₄) thin films of different thicknesses were deposited by chemical spray pyrolysis technique and utilized as a liquefied petroleum gas (LPG) sensors. These CdIn₂O₄ films were characterized for their structural and morphological properties by means of X-ray diffraction (XRD) and scanning electron microscope (SEM), respectively. The dependence of the LPG response on the operating temperature, LPG concentration and CdIn₂O₄ film thickness were investigated. The results showed that the phase structure and the LPG sensing properties changes with the different thicknesses. The maximum LPG response of 46% at the operation temperature of 673 K was achieved for the CdIn₂O₄ film of thickness of 695 nm. The CdIn₂O₄ thin films exhibited good response and rapid response/recovery characteristics to LPG.     

Electrical response of Sm2O3-doped SnO2 to C2H2 and effect of humidity interference

Pure and Sm₂O₃-doped SnO₂ are prepared through a sol–gel method and characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The sensor based on 6 wt% Sm₂O₃-doped SnO₂ displays superior response at an operating temperature of 180 °C, and the response magnitude to 1000 ppm C₂H₂ can reach 63.8, which is 16.8 times larger than that of pure SnO₂. This sensor also shows high sensitivity under various humidity conditions. These results make our product be a good candidate in fabricating C₂H₂ sensors.     

Selectivity of flame-spray-made Nb/ZnO thick films towards NO2 gas

Unloaded ZnO and Nb/ZnO nanoparticles containing 0.25, 0.5 and 1 mol.% Nb were produced in a single step by flame-spray pyrolysis (FSP) technique. The nanoparticles were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The BET surface area (SSA_BET) of the nanoparticles was measured by nitrogen adsorption. FSP yielded small Nb particles attached to the surface of the supporting ZnO nanoparticles, indicating a high SSA_BET. The morphology and accurate size of the primary particles were further investigated by TEM. Nb/ZnO nanoparticles paste composed of ethyl cellulose and terpineol as binder and solvent respectively was coated on Al₂O₃ substrate interdigitated with gold electrodes to form thick films by spin coating technique. After the sensing tests, the morphology and the cross-section of sensing film were analyzed by SEM and EDS analyses. The influence on a low dynamic range of Nb concentration on NO₂ response (0.1-4 ppm) of thick film sensor elements was studied at the operating temperatures ranging from 250 to 350 °C in the presence of dry air. The optimum Nb concentration was found be 0.5 mol.% and 0.5 mol.% Nb exhibited an optimum NO₂ response of ∼1640 and a short response time (27 s) for NO₂ concentration of 4 ppm at 300 °C.     

A route to high sensitivity and rapid response Nb2O5-based gas sensors: TiO2 doping, surface embossing, and voltage optimization

We report a novel route for the fabrication of highly sensitive and rapidly responding Nb₂O₅-based thin film gas sensors. TiO₂ doping of Nb₂O₅ films is carried out by co-sputtering without the formation of secondary phases and the surface area of TiO₂-doped Nb₂O₅ films is increased via the use of colloidal templates composed of sacrificial polystyrene beads. The gas sensitivity of Nb₂O₅ films is enhanced through both the TiO₂ doping and the surface embossing. An additional enhancement on the gas sensitivity is obtained by the optimization of the bias voltage applied between interdigitated electrodes beneath Nb₂O₅-based film. More excitingly, such a voltage optimization leads to a substantial decrease in response time. Upon exposure to 50 ppm CO at 350 °C, a gas sensor based on TiO₂-doped Nb₂O₅ film with embossed surface morphology exhibits a very high sensitivity of 475% change in resistance and a rapid response time of 8 s under 3 V, whereas a sensor based on plain Nb₂O₅ film shows a 70% resistance change and a response time of 65 s under 1 V. Thermal stability tests of our Nb₂O₅-based sensor reveal excellent reliability which is of particular importance for application as resistive sensors for a variety gases.     

In2O3 + xBaO (x = 0.5-5 at.%) - A novel material for trace level detection of NOx in the ambient

Indium oxide (In₂O₃) doped with 0.5-5 at.% of Ba was examined for their response towards trace levels of NO_x in the ambient. Crystallographic phase studies, electrical conductivity and sensor studies for NO_x with cross interference for hydrogen, petroleum gas (PG) and ammonia were carried out. Bulk compositions with x ≤ 1 at.% of Ba exhibited high response towards NO_x with extremely low cross interference for hydrogen, PG and ammonia, offering high selectivity. Thin films of 0.5 at.% Ba doped In₂O₃ were deposited using pulsed laser deposition technique using an excimer laser (KrF) operating at a wavelength of (λ) 248 nm with a fluence of ∼3 J/cm² and pulsed at 10 Hz. Thin film sensors exhibited better response towards 3 ppm NO_x quite reliably and reproducibly and offer the potential to develop NO_x sensors (Threshold limit value of NO₂ and NO is 3 and 25 ppm, respectively).     

Enhancing performance of FSP SnO2-based gas sensors through Sb-doping and Pd-functionalization

Via flame spray pyrolysis (FSP), SnO₂ gas sensing layers have been doped with 0.01-4 wt% Sb as well as 0.01 wt% Pd in combination with 1 wt% Sb. Characterization of these materials through X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) surface analysis, and transmission electron microscopy (TEM) revealed particle grain sizes and crystallinity unchanged by the presence of Sb and/or Pd. The addition of Sb to SnO₂ resulted in the significant decrease in baseline resistance; up to two orders of magnitude in dry air at 300 °C and three orders of magnitude in humid air at 300 °C, which is significant for FSP-prepared gas sensors with high porosity and low particle coordination number since they typically suffer from high baseline resistance. While the baseline resistance was improved with Sb-doping, the sensor signal (R₀/R_gas) remained constant over all concentrations explored. Moreover, regarding the surface functionalization of SnO₂ with Pd in combination with Sb-doping, the reduction of baseline resistance was preserved without influencing sensor signal.     

Enhanced C2H5OH sensing characteristics of nano-porous In2O3 hollow spheres prepared by sucrose-mediated hydrothermal reaction

In₂O₃ hollow spheres with shell thicknesses of ∼150 nm and ∼300 nm were prepared by the one-pot synthesis of indium-precursor-coated carbon spheres via hydrothermal reaction and subsequent removal of core carbon by heat treatment. The gas response (R_a/R_g, R_a: resistance in air, R_g: resistance in gas) of the thin hollow spheres to 100 ppm C₂H₅OH was 137.2 at 400 °C, which was 1.86 and 3.84 times higher than that of the thick hollow spheres and of the nanopowders prepared by precipitation, respectively. The gas sensing characteristics are discussed in relation to the shell configuration of the hollow spheres. The enhanced gas response of the hollow spheres was attributed to the effective diffusion of analyte gas toward the entire sensor surface via very thin and nano-porous shells.     

Synthesis of Bi and Gd doped ZnB2O4 for evaluation as potential materials in luminescent display applications

A series of Bi³⁺ and Gd³⁺ doped ZnB₂O₄ phosphors were synthesized with solid state reaction technique. X-ray diffraction technique was employed to study the structure of prepared samples. Excitation and emission spectra were recorded to investigate the luminescence properties of phosphors. The doping of Bi³⁺ or Gd³⁺ with a small amount (no more than 3 mol%) does not change the structure of prepared samples remarkably. Bi³⁺ in ZnB₂O₄ can emit intense broad-band purplish blue light peaking at 428 nm under the excitation of a broad-band peaking at 329 nm. The optimal doping concentration of Bi³⁺ is experimentally ascertained to be 0.5 mol%. The decay time of Bi³⁺ in ZnB₂O₄ changes from 0.88 to 1.69 ms. Gd³⁺ in ZnB₂O₄ can be excited with 254 nm ultraviolet light and yield intense 312 nm emission. The optimal doping concentration of Gd³⁺ is experimentally ascertained to be 5 mol%. The decay time of Gd³⁺ in ZnB₂O₄ changes from 0.42 to 1.36 ms.     

Enhanced H2S sensing characteristics of Pt doped SnO2 nanofibers sensors with micro heater

Gas sensors were designed and fabricated using oxide nanofibers as the sensing materials on micro platforms using micromachining technology. Pure and Pt doped SnO₂ nanofibers were prepared by electrospinning and their H₂S gas sensing characteristics were subsequently investigated. The sensing temperatures of 300 and 500 °C could be attained at the heater powers of 36 and 94 mW, respectively, and the sensors showed high and fast responses to H₂S. The responses of 0.08 wt% Pt doped SnO₂ nanofibers to 4-20 ppm H₂S, were 25.9-40.6 times higher than those of pure SnO₂ nanofibers. The gas sensing characteristics were discussed in relation to the catalytic promotion effect of Pt, nano-scale morphology of electrospun nanofibers, and sensor platform using micro heater.     

Plasma enhanced-CVD of undoped and fluorine-doped Co3O4 nanosystems for novel gas sensors

Co₃O₄-based nanosystems were prepared on polycrystalline Al₂O₃ by plasma enhanced-chemical vapor deposition (PE-CVD), at temperatures ranging between 200 and 400 °C. The use of two different precursors, Co(dpm)₂ (dpm = 2,2,6,6-tetramethyl-3,5-heptanedionate) and Co(hfa)₂·TMEDA (hfa = 1,1,1,5,5,5-hexafluoro-2,4-pentanedionate; TMEDA = N,N,N′,N′-tetramethylethylenediamine) enabled the synthesis of undoped and fluorine-doped Co₃O₄ specimens, respectively. A thorough characterization of their properties was performed by glancing incidence X-ray diffraction (GIXRD), atomic force microscopy (AFM), field emission-scanning electron microscopy (FE-SEM), secondary ion mass spectrometry (SIMS) and X-ray photoelectron spectroscopy (XPS). For the first time, the gas sensing properties of such PE-CVD nanosystems were investigated in the detection of ethanol and acetone. The results show an appreciable response improvement upon doping and functional performances directly dependent on the fluorine content in the Co₃O₄ system.     

Highly sensitive and selective LPG sensor based on α-Fe2O3 nanorods

The α-Fe₂O₃ nanorods were successfully synthesized without any templates by calcining the α-FeOOH precursor in air at 300 °C for 2 h and their LPG sensing characteristics were investigated. The α-FeOOH precursor was prepared through a simple and low cost wet chemical route at low temperature (40 °C) using FeSO₄·7H₂O and CH₃COONa as starting materials. The formation of α-FeOOH precursor and its topotactic transformation to α-Fe₂O₃ upon calcination was confirmed by X-ray diffraction measurement (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) analysis. The α-Fe₂O₃ nanorods exhibited outstanding gas sensing characteristics such as, higher gas response (∼1746-50 ppm LPG at 300 °C), extremely rapid response (∼3-4 s), relatively slow recovery (∼8-9 min), excellent repeatability, good selectivity and lower operating temperature (∼300 °C). Furthermore, the α-Fe₂O₃ nanorods are able to detect up to 5 ppm for LPG with reasonable response (∼15) at the operating temperature of 300 °C and they can be reliably used to monitor the concentration of LPG over the range (5-60 ppm). The experimental results clearly demonstrate the potential of using the α-Fe₂O₃ nanorods as sensing material in the fabrication of LPG sensors. Plausible LP G sensing mechanism of the α-Fe₂O₃ nanorods is also discussed.     

A novel bienzyme glucose biosensor based on three-layer Au-Fe3O4@SiO2 magnetic nanocomposite

The magnetic core-shell Au-Fe₃O₄@SiO₂ nanocomposite was prepared by layer-by-layer assembly technique and was used to fabricate a novel bienzyme glucose biosensor. Glucose oxidase (GOD) and horseradish peroxidase (HRP) were simply mixed with Au-Fe₃O₄@SiO₂ nanocomposite and cross-linked on the ITO magnetism-electrode with nafion (Nf) and glutaraldehyde (GA). The modified electrode was designated as Nf-GOD-HRP/Au-Fe₃O₄@SiO₂/ITO. The effects of some experimental variables such as the pH of supporting electrolyte, enzyme loading, the concentration of the mediator methylene blue (MB) and the applied potential were investigated. The electrochemical behavior of the biosensor was studied using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and chronoamperometry. Under the optimized conditions, the biosensor showed a wide dynamic range for the detection of glucose with linear ranges of 0.05-1.0 mM and 1.0-8.0 mM, and the detection limit was estimated as 0.01 mM at a signal-to-noise ratio of 3. The biosensor exhibited a rapid response, good stability and anti-interference ability. Furthermore, the biosensor was successfully applied to detect glucose in human serum samples, showing acceptable accuracy with the clinical method.     

Au-doped WO3-based sensor for NO2 detection at low operating temperature

Pure and Au-doped WO₃ powders for NO₂ gas detection were prepared by a colloidal chemical method, and characterized via X-ray powder diffraction (XRD), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). The NO₂ sensing properties of the sensors based on pure and Au-doped WO₃ powders were investigated by HW-30A gas sensing measurement. The results showed that the gas sensing properties of the doped WO₃ sensors were superior to those of the undoped one. Especially, the 1.0 wt% Au-doped WO₃ sensor possessed larger response, better selectivity, faster response/recovery and better longer term stability to NO₂ than the others at relatively low operating temperature (150 °C).     

Controlled synthesis and gas-sensing properties of hollow sea urchin-like α-Fe2O3 nanostructures and α-Fe2O3 nanocubes

Hollow sea urchin-like α-Fe₂O₃ nanostructures were successfully synthesized by a hydrothermal approach using FeCl₃ and Na₂SO₄ as raw materials, and subsequent annealing in air at 600 °C for 2 h. The hollow sea urchin-like α-Fe₂O₃ nanostructures with the diameters of 2–4.5 μm consist of well-aligned α-Fe₂O₃ nanorods with an average length of about 1 μm growing radially from the centers of the nanostructures, have a hollow interior with a diameter of about 2 μm. α-Fe₂O₃ nanocubes with a diameter of 700–900 nm were directly obtained by a hydrothermal reaction of FeCl₃ at 140 °C for 12 h. The response S_r (S_r = R_a/R_g) of the hollow sea urchin-like α-Fe₂O₃ nanostructures reached 2.4, 7.5, 5.9, 14.0 and 7.5 to 56 ppm ammonia, 32 ppm formaldehyde, 18 ppm triethylamine, 34 ppm acetone, and 42 ppm ethanol, respectively, which was excess twice that of the α-Fe₂O₃ nanocubes and the nanoparticle aggregations. Our results demonstrated that the hollow sea urchin-like α-Fe₂O₃ nanostructures were very promising for gas sensors for the detection of flammable and/or toxic gases with good-sensing characteristics.     

Studies on the gas sensing behaviour of nanosized CuNb2O6 towards ammonia, hydrogen and liquefied petroleum gas

Appreciable changes in resistance of polycrystalline nanosized CuNb₂O₆ upon exposure to reducing gases like hydrogen, liquefied petroleum gas (LPG) and ammonia in ambient atmosphere recognize the material as a gas sensor. Nanosized CuNb₂O₆ synthesized by thermal decomposition of an aqueous precursor solution containing copper nitrate, niobium tartrate and tri-ethanol amine (TEA), followed by calcination at 700 °C for 2 h, has been characterized using X-ray diffraction (XRD) study, transmission electron microscopy (TEM), field-emission scanning electron microscope (FESEM), energy dispersive X-ray (EDX) analysis and Brunauer–Emmett–Teller (BET) surface area measurement. The synthesized CuNb₂O₆ exhibits monoclinic structure with crystallite size of 25 nm, average particle size of 25–40 nm and specific surface area of 55 m² g⁻¹.