Fe2O3 modified thick films of nanostructured SnO2 powder consisting of hollow microspheres synthesized from pyrolysis of ultrasonically atomized aerosol for LPG sensing

Nanostructured hollow spheres of SnO₂ with fine nanoparticles were synthesized by ultrasonic atomization. Thick film gas sensors were fabricated by screen printing technique. Different surface modified films (Fe₂O₃ modified SnO₂) were obtained by dipping them into an aqueous solution (0.01 M) of ferric chloride for different intervals of time followed by firing at 500 °C. The structural and microstructural studies of the samples were carried out using XRD, SEM, and TEM. The sensing performance of pure and modified films was studied by exposing various gases at different operating temperatures. One of the modified sample exhibited high response (1990) to 1000 ppm of LPG at 350 °C. Optimum amount of Fe₂O₃ dispersed evenly on the surface_, adsorption and spillover of LPG on Fe₂O₃ misfits and high capacity of adsorption of oxygen on nanostructured hollow spheres may be the reasons of high response.     

Nano particulate SnO2 based resistive films as a hydrogen and acetone vapour sensor

SnCl₂ (solution) was spin coated on soda lime glass and Al₂O₃ substrate to obtain nano-particulate tin oxide film, directly by sintering at 550 °C for 40 minutes (min). The surface morphology and crystal structure of the tin oxide films were analyzed using atomic force microscopy (AFM) and X-ray diffraction (XRD). The size of SnO₂ nanostructure was determined from UV-vis and found to be ?3 nm. These films were tested for sensing H₂ concentration of 0.1-1000 ppm at optimized operating temperature of 265 °C. The results showed that sensitivity (R_air/R_gas per ppm) goes on increasing with decreasing concentration of test gas, giving concentration dependent changes. Special studies carried out at low concentration levels (0.1-1 and 1-10 ppm) of H₂, give high sensitivity (200 × 10⁻³/ppm) for lowest concentration (0.1-1 ppm) of H₂. The selectivity for H₂ against relative humidity (RH), CO₂, CO and LPG gases is also good. The sensor, at operating temperature of 200 °C, is showing nearly zero response to 300 ppm of H₂, and offering response to acetone vapour of 11 ppm. Selectivity for acetone against RH% and CO₂ was also studied. These sensors can be used as H₂ sensor at an operating temperature of 265 °C, and as an acetone sensor at the operating temperature of 200 °C.     

Nanostructured spinel ZnCo2O4 for the detection of LPG

Nanostrucutred spinel ZnCo₂O₄ (∼26-30 nm) was synthesized by calcining the mixed precursor (consisting of cobalt hydroxyl carbonate and zinc hydroxyl carbonate) in air at 600 °C for 5 h. The mixed precursor was prepared through a low cost and simple co-precipitation/digestion method. The transformation of the mixed precursor into nanostructured spinel ZnCo₂O₄ upon calcinations was confirmed by X-ray diffraction (XRD) measurement, thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and high resolution transmission electron microscopy (HRTEM). To demonstrate the potential applicability of ZnCo₂O₄ spinel in the fabrication of gas sensors, its LPG sensing characteristics were systematically investigated. The ZnCo₂O₄ spinel exhibited outstanding gas sensing characteristics such as, higher gas response (∼72-50 ppm LPG gas at 350 °C), response time (∼85-90 s), recovery time (∼75-80 s), excellent repeatability, good selectivity and relatively lower operating temperature (∼350 °C). The experimental results demonstrated that the nanostructured spinel ZnCo₂O₄ is a very promising material for the fabrication of LPG sensors with good sensing characteristics. Plausible LPG sensing mechanism is also discussed.     

Enhanced H2S sensing characteristics of Pt doped SnO2 nanofibers sensors with micro heater

Gas sensors were designed and fabricated using oxide nanofibers as the sensing materials on micro platforms using micromachining technology. Pure and Pt doped SnO₂ nanofibers were prepared by electrospinning and their H₂S gas sensing characteristics were subsequently investigated. The sensing temperatures of 300 and 500 °C could be attained at the heater powers of 36 and 94 mW, respectively, and the sensors showed high and fast responses to H₂S. The responses of 0.08 wt% Pt doped SnO₂ nanofibers to 4-20 ppm H₂S, were 25.9-40.6 times higher than those of pure SnO₂ nanofibers. The gas sensing characteristics were discussed in relation to the catalytic promotion effect of Pt, nano-scale morphology of electrospun nanofibers, and sensor platform using micro heater.     

Fabrication of N-type Fe2O3 and P-type LaFeO3 nanobelts by electrospinning and determination of gas-sensing properties

N-type Fe₂O₃ nanobelts and P-type LaFeO₃ nanobelts were prepared by electrospinning. The structure and micro-morphology of the materials were characterized by X-ray diffraction (XRD) and scanning of electron microscopy (SEM). The gas sensing properties of the materials were investigated. The results show that the optimum operating temperature of the gas sensors fabricated from Fe₂O₃ nanobelts is 285 °C, whereas that from LaFeO₃ nanobelts is 170 °C. Under optimum operating temperatures at 500 ppm ethanol, the response of the gas sensors based on these two materials is 4.9 and 8.9, respectively. The response of LaFeO₃-based gas sensors behaves linearly with the ethanol concentration at 10-200 ppm. Sensitivities to different gases were examined, and the results show that LaFeO₃ nanobelts exhibit good selectivity to ethanol, making them promising candidates as practical detectors of ethanol.     

Effect of thickness of platinum catalyst clusters on response of SnO2 thin film sensor for LPG

This paper reports the sensing response characteristics of rf-sputtered SnO₂ thin films (90 nm thick) loaded with platinum catalyst cluster of varying thickness (2-20 nm) for LPG detection. The enhanced response (5 × 10³) was obtained for 200 ppm LPG with the presence of 10 nm thin and uniformly distributed Pt catalyst clusters on the surface of SnO₂ thin film at a relatively low operating temperature (220 °C). The high response for LPG is shown to be primarily due to the enhanced catalytic activity for adsorbed oxygen on the surface of SnO₂ thin film besides the spill over mechanism at elevated temperature.     

Sprayed CdIn2O4 thin films for liquefied petroleum gas (LPG) detection

Nanocrystalline cadmium indium oxide (CdIn₂O₄) thin films of different thicknesses were deposited by chemical spray pyrolysis technique and utilized as a liquefied petroleum gas (LPG) sensors. These CdIn₂O₄ films were characterized for their structural and morphological properties by means of X-ray diffraction (XRD) and scanning electron microscope (SEM), respectively. The dependence of the LPG response on the operating temperature, LPG concentration and CdIn₂O₄ film thickness were investigated. The results showed that the phase structure and the LPG sensing properties changes with the different thicknesses. The maximum LPG response of 46% at the operation temperature of 673 K was achieved for the CdIn₂O₄ film of thickness of 695 nm. The CdIn₂O₄ thin films exhibited good response and rapid response/recovery characteristics to LPG.     

Improved crystalline structure and H2S sensing performance of CuO-Au-SnO2 thin film using SiO2 additive concentration

In situ SiO₂-doped SnO₂ thin films were successfully prepared by liquid phase deposition. The influence of SiO₂ additive as an inhibitor on the surface morphology and the grain size for the thin film has been investigated. These results show that the morphology of SnO₂ film changes significantly by increasing the concentration of H₂SiF₆ solution which decreases the grain size of SnO₂. The stoichiometric analysis of Si content in the SnO₂ film prepared from various Si/Sn molar ratios has also been estimated. For the sensing performance of H₂S gas, the SiO₂-doped Cu-Au-SnO₂ sensor presents better sensitivity to H₂S gas compared with Cu-Au-SnO₂ sensor due to the fact that the distribution of SiO₂ particles in grain boundaries of nano-crystallines SnO₂ inhibited the grain growth (<6 nm) and formed a porous film. By increasing the Si/Sn molar ratio, the SiO₂-doped Cu-Au-SnO₂ gas sensors (Si/Sn = 0.5) exhibit a good sensitivity (S = 67), a short response time (t_90% < 3 s) and a good gas concentration characteristic (α = 0.6074). Consequently, the improvement of the nano-crystalline structures and high sensitivity for sensing films can be achieved by introducing SiO₂ additive into the SnO₂ film prepared by LPD method.     

Electrostatic sprayed SnO2 and Cu-doped SnO2 films for H2S detection

This paper presents the ability of electrostatic sprayed tin oxide (SnO₂) and tin oxide doped with copper oxide (1, 2, and 4 at.% Cu) films to detect different pollutant gases, i.e., H₂S, SO₂, and NO₂. The influence of a copper oxide dopant on the SnO₂ morphology is studied using scanning electron microscopy (SEM) technique, which reveals a small decrease in the porosity and particle size when the amount of dopant is increased. The sensing properties of the SnO₂ films are greatly improved by doping, i.e., the Cu-doped SnO₂ films have large response to low concentration (10 ppm) of H₂S at low operating temperature (100 °C). Furthermore, no cross-sensitivity to 1 ppm NO₂ and 20 ppm SO₂ is observed. Among the studied films, the 1 at.% Cu-doped SnO₂ layer is the most sensitive in the detection of all the studied gases.     

Enhanced C2H5OH sensing characteristics of nano-porous In2O3 hollow spheres prepared by sucrose-mediated hydrothermal reaction

In₂O₃ hollow spheres with shell thicknesses of ∼150 nm and ∼300 nm were prepared by the one-pot synthesis of indium-precursor-coated carbon spheres via hydrothermal reaction and subsequent removal of core carbon by heat treatment. The gas response (R_a/R_g, R_a: resistance in air, R_g: resistance in gas) of the thin hollow spheres to 100 ppm C₂H₅OH was 137.2 at 400 °C, which was 1.86 and 3.84 times higher than that of the thick hollow spheres and of the nanopowders prepared by precipitation, respectively. The gas sensing characteristics are discussed in relation to the shell configuration of the hollow spheres. The enhanced gas response of the hollow spheres was attributed to the effective diffusion of analyte gas toward the entire sensor surface via very thin and nano-porous shells.     

Tetrakis(alkylthio)-substituted lutetium bisphthalocyanines for sensing NO2 and O3

In this study, the nitrogen dioxide (NO₂) and ozone (O₃) sensing properties of a series bis[tetrakis(alkylthio) phthalocyaninato] lutetium(III) complexes [(C_nH_2n+1S)₄Pc]₂Lu(III) (n = 6, 10, 16) are investigated as a function of concentration in the temperature range between 25 °C and 150 °C. The concentration ranges were 1–10 ppm for NO₂, and 50 ppb–1 ppm for O₃. The response time and the sensor response to NO₂ are measured for approximately 1 min and 100% ppm⁻¹, respectively, for compound 1 at room temperature. At room temperature, all compounds are in the solid phase. The response time decreases to a few seconds with increasing operation temperature to 150 °C. At this temperature, all compounds are in the liquid crystal phase. The fastest response to oxidizing gases is observed at the liquid crystal phase of the Pcs. It has also been observed that the response time and the sensor response depend on the alkyl chain lengths of the Pcs. The doping effect of oxygen has been determined under high purity nitrogen N₂ flow, after exposure to dry air, at a different period of time and after annealing. It has been found that the conductivities of [(C_nH_2n+1S)₄Pc]₂Lu(III) thin films increased after exposure to dry air and the conduction mechanism also changed from ohmic behavior to space-charge-limited conduction.     

SnO2 thin film sensor with enhanced response for NO2 gas at lower temperatures

Semiconducting SnO₂ thin films having higher value of electrical conductivity have been deposited using RF sputtering technique in the reactive gas environment (30% O₂ + 70% Ar) using a metallic tin (Sn) target for detection of oxidizing NO₂ gas. The effect of growth pressure (12-18 mTorr) on the surface morphology and structural property of SnO₂ film was studied using Atomic force microscopy (AFM), Scanning electron microscopy (SEM) and X-ray Diffraction (XRD) respectively. Film deposited at 16 mTorr sputtering pressure was porous with rough microstructure and exhibits high sensor response (∼2.9 × 10⁴) towards 50 ppm NO₂ gas at a comparatively low operating temperature (∼100 °C). The sensor response was found to increase linearly from 1.31 × 10² to 2.9 × 10⁴ while the response time decrease from 12.4 to 1.6 min with increase in the concentration of NO₂ gas from 1 to 50 ppm. The reaction kinetics of target NO₂ gas on the surface of SnO₂ thin film at the Sn sites play important role in enhancing the response characteristics at lower operating temperature (∼100 °C). The results obtained in the present study are encouraging for realization of SnO₂ thin film based sensor for efficient detection of NO₂ gas with low power consumption.     

The effect of La2CuO4 sensing electrode thickness on a potentiometric NOx sensor response

In order to further understand the different contributions to NO_x sensing mechanism as well as the importance of electrode geometry, solid state potentiometric sensors with varying La₂CuO₄ sensing electrode thicknesses were studied. These sensors (with a Pt counter electrode) showed a dependence of NO₂ sensitivity which decreased with increasing thickness in the temperature range of 550-650 °C. They also showed NO sensitivity that was independent of thickness at 400 °C and 600 °C, but varied at temperatures between. This behavior was attributed to multiple mechanistic contributions explained by Differential Electrode Equilibria.     

Selectivity of flame-spray-made Nb/ZnO thick films towards NO2 gas

Unloaded ZnO and Nb/ZnO nanoparticles containing 0.25, 0.5 and 1 mol.% Nb were produced in a single step by flame-spray pyrolysis (FSP) technique. The nanoparticles were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The BET surface area (SSA_BET) of the nanoparticles was measured by nitrogen adsorption. FSP yielded small Nb particles attached to the surface of the supporting ZnO nanoparticles, indicating a high SSA_BET. The morphology and accurate size of the primary particles were further investigated by TEM. Nb/ZnO nanoparticles paste composed of ethyl cellulose and terpineol as binder and solvent respectively was coated on Al₂O₃ substrate interdigitated with gold electrodes to form thick films by spin coating technique. After the sensing tests, the morphology and the cross-section of sensing film were analyzed by SEM and EDS analyses. The influence on a low dynamic range of Nb concentration on NO₂ response (0.1-4 ppm) of thick film sensor elements was studied at the operating temperatures ranging from 250 to 350 °C in the presence of dry air. The optimum Nb concentration was found be 0.5 mol.% and 0.5 mol.% Nb exhibited an optimum NO₂ response of ∼1640 and a short response time (27 s) for NO₂ concentration of 4 ppm at 300 °C.     

Electrospun Cu-doped ZnO nanofibers for H2S sensing

Pure and Cu-doped ZnO nanofibers were synthesized via electrospinning technology. The morphology and structure of the as-synthesized nanofibers were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and Raman spectroscopy. The effects of Cu doping on H₂S sensing properties at low concentration (1-10 ppm) were investigated at 230 °C. The results show that the H₂S sensing properties of ZnO nanofibers are effectively improved by Cu doping: 6 at% Cu-doped ZnO nanofibers show a maximum sensitivity to H₂S gas, and the response to 10 ppm H₂S is one order of magnitude higher than the one of pure ZnO nanofibers.     

Microstructure control of TiO2 nanotubular films for improved VOC sensing

Porous gas sensing films composed of TiO₂ nanotubes were fabricated for the detection of volatile organic compounds (VOCs), such as alcohol and toluene. In order to control the microstructure of TiO₂ nanotubular films, ball-milling treatments were used to shorten the length of TiO₂ nanotubes and to improve the particle packing density of the films without destroying their tubular morphology and crystal structure. The ball-milling treatment successfully modified the porosity of the gas sensing films by inducing more intimate contacts between nanotubes, as confirmed by scanning electron microscopy (SEM) and mercury porosimetry. The sensor using nanotubes after the ball-milling treatment for 3 h exhibited an improved sensor response and selectivity to toluene (50 ppm) at the operating temperature of 500 °C. However, an extensive ball-milling treatment did not enhance the original sensor response, probably owing to a decrease in the porosity of the film. The results obtained indicated the importance of the microstructure control of sensing layers in terms of particle packing density and porosity for detecting large sized organic gas molecules.     

Synthesis and characterisation of nanosized TiO2-ZrO2 binary system prepared by an aqueous sol-gel process: Physical and sensing properties

Nanostructured TiO₂-ZrO₂ thin films and powders were prepared by a straightforward aqueous particulate sol-gel route. Titanium (IV) isopropoxide and zirconium (IV) acetate hydrate were used as precursors, and hydroxypropyl cellulose was used as a polymeric fugitive agent in order to increase the specific surface area. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy revealed that the powder were crystallised at the low temperature of 500 °C, containing anatase-TiO₂ and tetragonal-ZrO₂ phases. Furthermore, it was found that ZrO₂ retarded the anatase-to-rutile transformation up to 900 °C. The activation energies for crystallite growth of TiO₂ and ZrO₂ components in the binary system were calculated 10.16 and 3.12 kJ/mol, respectively. Transmission electron microscope (TEM) image showed that one of the smallest crystallite sizes was obtained for TiO₂-ZrO₂ binary mixed oxide, being 5 nm at 500 °C. Field emission scanning electron microscope (FESEM) analysis revealed that the deposited thin films had nanostructured morphology with the average grain size of 20 nm at 500 °C and 36 nm at 900 °C. Thin films produced under optimised conditions showed excellent microstructural properties for gas sensing applications. They exhibited a remarkable response towards low concentrations of CO and NO₂ gases at low operating temperature of 150 °C, resulted in an increase of thermal stability of sensing films as well as a decrease in the power consumption. Furthermore, calibration curves revealed that TiO₂-ZrO₂ sensor follows the power law, S = A[gas]^B (where S is sensor response, coefficients A and B are constants and [gas] is gas concentration) for the two types of gases, and it has excellent capability for the detection of low gas concentrations.     

Acetylene sensor based on Pt/ZnO thick films as prepared by flame spray pyrolysis

ZnO nanoparticles loaded with 0.2-2.0 at.% Pt have been successfully produced in a single step by flame spray pyrolysis (FSP) technique using zinc naphthenate and platinum(II) acetylacetonate, as precursors dissolved in xylene and their acetylene sensing characteristics have been investigated. The particle properties were analyzed by XRD, BET, TEM, SEM and EDS. Under the 5/5 (precursor/oxygen) flame condition, ZnO nanoparticles and nanorods were observed. The crystallite sizes of ZnO spherical and hexagonal particles were found to be ranging from 5 to 20 nm while ZnO nanorods were seen to be 5-20 nm in width and 20-40 nm in length. In addition, very fine Pt nanoparticles with diameter of ∼1 nm were uniformly deposited on the surface of ZnO particles. From gas-sensing characterization, acetylene sensing characteristics of ZnO nanoparticles is significantly improved as Pt content increased from 0 to 2  at.%. The 2 at.% Pt loaded ZnO sensing film showed an optimum C₂H₂ response of ∼836 at 1% acetylene concentration and 300 °C operating temperature. A low detection limit of 50 ppm was obtained at 300 °C operating temperature. In addition, Pt loaded ZnO sensing films exhibited good selectivity towards hydrogen, methane and carbon monoxide.     

Solid-state potentiometric SO2 sensor combining NASICON with V2O5-doped TiO2 electrode

A compact tubular sensor based on NASICON (sodium super ionic conductor) and V₂O₅-doped TiO₂ sensing electrode was designed for the detection of SO₂. In order to reduce the size of the sensor, a thick-film of NASICON was formed on the outer surface of a small Al₂O₃ tube; furthermore, a thin layer of V₂O₅-doped TiO₂ with nanometer size was attached on the NASICON as a sensing electrode. This paper investigated the influence of V₂O₅ doping and sintering temperature on the characteristics of the sensor. The sensor attached with 5 wt% V₂O₅-doped TiO₂ sintered at 600 °C exhibited excellent sensing properties to 1–50 ppm SO₂ in air at 200–400 °C. The EMF value of the sensor was almost proportional to the logarithm of SO₂ concentration and the sensitivity (slope) was −78 mV/decade at 300 °C. It was also seen that the sensor showed a good selectivity to SO₂ against NO, NO₂, CH₄, CO, NH₃ and CO₂. Moreover, the sensor had speedy response kinetics to SO₂ too, the 90% response time to 50 ppm SO₂ was 10 s, and the recovery time was 35 s. On the basis of XPS analysis for the SO₂-adsorbed sensing electrode, a sensing mechanism involving the mixed potential at the sensing electrode was proposed.     

Facile synthesis of hierarchical SnO2 semiconductor microspheres for gas sensor application

Hierarchical SnO₂ microspheres were synthesized by a hydrothermal method at 140 °C using stannic chloride hydrate and sodium hydroxide as starting materials. The individual hierarchical SnO₂ microsphere ranged from 700 to 900 nm in diameter. After these microspheres were heated at 600 °C for 2 h, the spheres were cross-linked into clusters by short SnO₂ nanorods as revealed by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Most importantly, SnO₂ hierarchical microsphere sensor exhibits excellent selectivity and fast response to ethanol. Response and recovery times were 0.6 s and 11 s when the sensor was exposed to 50 ppm ethanol at an operating temperature of 300 °C. Thus, hierarchical structures play a significant role in the field of gas sensing.