Synthesis and evaluation of the thermal properties of biosourced poly(ether)ureas and copoly(ether)ureas from 1,4:3,6‐dianhydrohexitols

A new series of poly(ether)ureas were prepared by solution polyaddition of three diamines based on 1,4:3,6‐dianhydrohexitols with three types of diisocyanate. The corresponding poly(ether)ureas were obtained with high yields. They were characterized by various analytical techniques (NMR, TGA and differential thermal analysis, DSC). NMR spectroscopy allowed us to confirm structure type and to optimize reaction conditions and DSC proved the high thermal properties of the products obtained (T_g and T_m in the range 126 ? 158 °C and 235 ? 330 °C respectively). Then, copoly(ether)ureas partially based on commercial diamines were synthesized in order to reduce polymer cost and tune their thermal behaviour. The reactivity of both diamines was evaluated by their incorporation in the polymer by means of NMR spectra. Then their thermal properties were compared with fully commercial diamine based polyureas by DSC studies. © 2014 Society of Chemical Industry     

Synthesis and characterization of novel organosoluble biosourced poly(ester imide)s based on 1,4:3,6 -dianhydrohexitols suited for adhesives applications

A new series of poly(ester imide)s were prepared from the polycondensation of isosorbide and a series of synthesized diacyl chloride monomers based on a reaction between 1,2,4-Benzenetricarboxylic anhydride (TMA) and various diamines. The structures of the resulting polymers were confirmed by Fourier transform infrared spectroscopy (FTIR) and ¹³C NMR spectra. Inherent viscosities and size exclusion chromatography (SEC) measurements proved the formation of high molecular weight poly(ester imide)s. The thermogravimetric analysis (TGA) showed deterioration temperature in the range of 221–400 °C indicating a good thermal stability. The differential scanning calorimetry (DSC) measurements revealed high glass transition temperature in the range of 67–185 °C. Wide angle X-ray diffraction measurements showed that the studied poly(ester imide)s were semi-crystalline. Most of the synthesized poly(ester imide) exhibited a good adhesion ability and tensile strength values comparable to analogous polymers.     

Biodegradable polymers based on renewable resources. V. Synthesis and biodegradation behavior of poly(ester amide)s composed of 1,4:3,6‐dianhydro‐D‐glucitol, α‐amino acid,and aliphatic dicarboxylic acid units

A series of poly(ester amide)s were synthesized by solution polycondensations of various combinations of p‐toluenesulfonic acid salts of O,O′‐bis(α‐aminoacyl)‐1,4:3,6‐dianhydro‐D ‐glucitol and bis(p‐nitrophenyl) esters of aliphatic dicarboxylic acids with the methylene chain lengths of 4–10. The p‐toluenesulfonic acid salts were obtained by the reactions of 1,4:3,6‐dianhydro‐D ‐glucitol with alanine, glycine, and glycylglycine, respectively, in the presence of p‐toluenesulfonic acid. The polycondensations were carried out in N‐methylpyrrolidone at 40°C in the presence of triethylamine, giving poly(ester amide)s having number‐average molecular weights up to 3.8 × 10⁴. Their structures were confirmed by FTIR, ¹H‐NMR, and ¹³C‐NMR spectroscopy. Most of these poly(ester amide)s are amorphous, except those containing sebacic acid and glycine or glycylglycine units, which are semicrystalline. All these poly(ester amide)s are soluble in a variety of polar solvents such as dimethyl sulfoxide, N,N‐dimethylformamide, 2,2,2‐trifluoroethanol, m‐cresol, pyridine, and trifluoroacetic acid. Soil burial degradation tests, BOD measurements in an activated sludge, and enzymatic degradation tests using Porcine pancreas lipase and papain indicated that these poly(ester amide)s are biodegradable, and that their biodegradability markedly depends on the molecular structure. The poly(ester amide)s were, in general, degraded more slowly than the corresponding polyesters having the same aliphatic dicarboxylic acid units, both in composted soil and in an activated sludge. In the enzymatic degradation, some poly(ester amide)s containing dicarboxylic acid components with shorter methylene chain lengths were degraded more readily than the corresponding polyesters with Porcine pancreas lipase, whereas most of the poly(ester amide)s were degraded more rapidly than the corresponding polyesters with papain. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2721–2734, 2001     

AB型羟基改性PBO单体及其合成新技术

提出单羟基改性PBO及其AB型单体的分子结构,研究了以4-氨基-6-硝基间苯二酚盐酸盐(ANR·HCl)和羟基对苯二甲酸(HTA)为原料直接缩环合制备2-羟基-4-(5-硝基-6-羟基苯并 唑-2-基)苯甲酸(HNBA)、再还原合成AB型单体:2-羟基-4-(5-氨基-6-羟基苯并 唑-2-基)苯甲酸(HABA)的新方法。结果表明:缩环合制备的HNBA,其纯度96.81%、收率69.25%;进一步还原合成出纯度>98%的单体HABA,以ANR·HCl计的总收率为58.38%;具有原料易得、步骤短、条件缓和、产物稳定性优异以及缩聚基团完全等当比等性质。合成的新单体HABA及其前体HNBA,经FT-IR和MS以及NMR等分析和表征,证实了其分子结构。     

玻璃布增强聚苯醚/三烯丙基异氰酸酯复合材料耐热性和相态研究

利用差示扫描量热仪和扫描电镜研究了聚苯醚(PPE)/三烯丙基异氰酸酯(TAIC)树脂的耐热性以及玻璃布增强PPE/TAIC复合材料的耐热性和相态。结果表明:PPE/TAIC树脂混合物的耐热性随着PPE质量分数的增加而提高,且玻璃布增强PPE/TAIC复合材料的热稳定性优于纯PPE/TAIC树脂混合物;偶联剂的种类对PPE/TAIC复合材料的界面状态有较大的影响,A-172对PPE/TAIC复合材料来说是有效的硅烷偶联剂。     

New polymer syntheses: II. Preparation of aromatic poly(ether ketone)s from silylated bisphenols

Bulk condensations of 4,4′-difluorobenzophenone and various silylated bisphenols were carried out at 220°–320°C, with caesium fluoride as catalyst. Silylated bisphenol-A, tetramethylbisphenol-A, 1,1-bis(4-hydroxyphenyl)cyclohexane or 4,4′-dihydroxydiphenylsulphone as monomers and glassy polymers were soluble in several organic solvents. Their glass transitions were determined by differential scanning calorimetry (d.s.c.) and their number molecular weights ($\text{M}\text{?}{}_{\mathrm{<mtext>n</mtext>}}$) determined by means of vapour pressure osmometry. M_n's up to 10 000 were obtained. When silylated hydroquinone, 4,4′-dihydroxydiphenyl, 2,7-dihydroxynaphthalene or 4,4′-dihydroxydiphenylsulphide undergo polycondensation the resulting poly (ether ketone)s form crystals. It is demonstrated that transesterification does not take place and that block copoly(ether ketone-ether sulphone)s are synthesized. Furthermore, the thermostability of the poly(ether ketone)s in air was investigated.     

Synthesis and characterization of fluorinated poly(azomethine ether)s from new core-fluorinated azomethine-containing monomers

In this work, we describe the design and synthesis of novel core-fluorinated Schiff base monomers and conjugated polymers based on them. The new fully aromatic highly fluorinated poly(azomethine ether)s (PAMEs) were prepared by polycondensation of core-fluorinated azomethine-containing compounds. The structure of the monomers and polymers were confirmed by FTIR, ¹H, ¹³C, and ¹⁹F NMR spectroscopic analysis. The influence of synthesis condition on the properties of PAME compounds was investigated. Application of polarization microscopy with a temperature control thermal stage revealed thermotropic liquid crystalline (LC) behavior in the synthesized materials. Transition temperatures and a range of the existence of the LC phase were studied by a combination of the optical microscopy and DSC analysis. According to the TGA analysis, all the synthesized PAMEs show high thermal stability and thus offer a wide range of thermal processibility (up to 410–477 °C), which makes them prospective materials for many modern applications.     

Biodegradable poly(ester‐ether)s: ring‐opening polymerization of D,L‐3‐methyl‐1,4‐dioxan‐2‐one using various initiator systems

The synthesis and detailed characterization of racemic 3‐methyl‐1,4‐dioxan‐2‐one (3‐MeDX) are reported. The bulk ring‐opening polymerization of 3‐MeDX, to yield a poly(ester‐ether) meant for biomedical applications, in the presence of various initiators such as tin(II) octanoate, tin(II) octanoate/n‐butyl alcohol, aluminium tris‐isopropoxide and an aluminium Schiff base complex (HAPENAlOⁱPr) under varying experimental conditions is here detailed for the first time. Polymerization kinetics were investigated and compared with those of 1,4‐dioxan‐2‐one. The studies reveal that the rate of polymerization of 3‐MeDX is less than that of 1,4‐dioxan‐2‐one. Experimental conditions to achieve relatively high molar masses have been established. Thermodynamic parameters such as enthalpy and entropy of 3‐MeDX polymerization as well as ceiling temperature have been determined. Poly(D ,L ‐3‐MeDX) is found to possess a much lower ceiling temperature than poly(1,4‐dioxan‐2‐one). Poly(D ,L ‐3‐MeDX) was characterized using NMR spectroscopy, matrix‐assisted laser desorption ionization mass spectrometry, size exclusion chromatography and differential scanning calorimetry. This polymer is an amorphous material with a glass transition temperature of about ?20 °C. Copyright © 2010 Society of Chemical Industry     

Microporous membranes prepared from blends of polysulfone and sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide)

Membranes were prepared from solutions containing Udel‐type polysulfone (PSf) and sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (SPPO). Polymer solutions in 1‐methyl‐2‐pyrrolidone were cast on a nonwoven textile and precipitated in a water bath. The permeabilities and selectivities of the prepared membranes depended on the concentrations of both polymers in the casting solution. The higher the concentration of PSf, the lower were the permeabilities to water and average pore sizes of the membranes. On the other hand, a very small amount of SPPO in the casting solution (about 1–4 wt % relative to the casting solution weight) brought about a considerable increase in water permeabilities and had a small influence on the average pore sizes. The effects were most pronounced if SPPO with a degree of sulfonation of 20–40% was used. The considerable increase in water permeabilities was explained by separation of the PSf and SPPO phases during precipitation in water and by the concentration of hydrophilic SPPO on the surface of the membrane and its pores. The determinations of the oriented concentration potentials proved the presence of a negative surface charge in the membranes. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 134–142, 2001     

Blends of Poly(ether imide) and Styrene Sulfonic Acid Based Polymer: Thermal,Mechanical and Ionic Conduction Behavior

Dense membranes based on poly(ether imide) (PEI) and poly(styrene sulfonic acid-co-maleic acid) (PSSAMA) was obtained by extrusion and compression molding. Blends with different PSSAMA content (1, 3, 5, and 10 wt%) were prepared. Their morphology was investigated by scanning electron microscopy (SEM) and their thermal properties by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dynamic-mechanical analysis (DMA). Two glass transition temperatures (T_g) (100 and 216°C) appeared when high contents of PSSAMA were added to PEI, indicating that the polymers form an immiscible system. TGA curves showed that the first weight loss occurred above 400°C for all blends, indicating a good thermal stability. Water uptake measurements have shown that the membranes presented low swelling when compared with Nafion®. The proton conductivity of the membrane with 10 wt% of PSSAMA obtained bv impedance measurements was 0.006 × 10^?2 S·cm^?1.     

Structural and mechanical characterization of poly(ether ether ketone) (PEEK) and sulfonated PEEK films: Effects of thermal history,sulfonation, and preparation conditions

In this work, virgin and sulfonated poly(ether ether ketone) films (PEEK and SPEEK, respectively) have been studied by dynamic mechanical analysis, modulated differential scanning calorimetry, wide‐angle X‐ray diffraction, birefringence, and optical microscopy. The properties of the unmodified polymer have been addressed to assess the original morphological characteristics and the changes induced by sulfonation. In general, the introduction of ionic groups in the polymer backbone alters dramatically the intrinsic properties of the parent material. The particular thermomechanical response exhibited by PEEK and SPEEK samples, characterized by a hysteresis loop, can be explained by the reversible and irreversible relaxation–orientation of the microstructure, even in the sub‐T_g region. The results showed that the preparation conditions largely determine the nonequilibrium morphological features of both compression‐molded PEEK films and solvent‐cast SPEEK membranes. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 756–774, 2006     

Microstructural Development of Uniaxial Stretched Anneal-Oriented Syndiotactic Polystyrene and its Blend with Poly (2,6-dimethyl-1,4-phenylene oxide): DSC,WAXD, SAXS and FTIR Studies

Studies have been done on strain-induced microstructure development in syndiotactic polystyrene (s-PS) and its blends with poly (2,6-dimethyl-1,4-phenylene oxide) (PPO) in 70/30 and 50/50 compositions of stretched annealed samples. Wide-angle X-ray showed that crystal orientation is less in annealed blend samples compared to annealed pure s-PS for a higher draw ratio. It increases with annealing, and relaxation occurs after a certain annealing temperature at above 180° for both s-PS and s-PS/PPO 70/30 blends. No crystal orientation was observed in the blend of s-PS/PPO 50/50 stretched samples. Small angle X-ray scattering (SAXS) shows the inclusion of amorphous PPO chains in between s-PS crystals lamella. Fourier transform infrared (FTIR) spectroscopy shows that the s-PS molecular chain packing band at 905 cm^?1 is enhanced due to annealing in oriented samples and saturates to around 0.63. The crystal chain relaxation is lower than amorphous chains of s-PS. The molecular chains of amorphous PPO are less oriented into the blend matrix, whereas its relaxation is enhanced during heat treatment and reaches an optimum value after full relaxation. The different behaviors of orientation and relaxation of s-PS and PPO chains into the blend matrix produce superstructures.     

Soluble and crosslinkable poly(phthalazinone ether ketone)s with pendent terminal ethynyl groups: synthesis,characterization and click modification

New poly(phthalazinone ether ketone)s (PPEKs) with pendent terminal ethynyl groups were synthesized by the aromatic nucleophilic substitution (S_NAr) polycondensation reaction of a new bisphenol monomer, 2‐(3‐ethynylphenyl)hydroquinone, with 4‐(4′‐hydroxyphenyl)phthalazin‐1(2H)‐one and 4,4′‐bis(4‐fluorophenyl) ketone, followed by click modification reaction with 1‐azidopyrene. Fourier transform infrared and NMR spectral data of the model compound indicated that the terminal ethynyl groups were stable in S_NAr reaction conditions, thus allowing the synthesis of the desired polymers. The PPEKs obtained with glass transition temperature (T_g) in the range 152–245 °C were amorphous, characterized by wide‐angle X‐ray diffraction, and dissolved in organic solvent to cast into transparent and flexible films. Differential scanning calorimetry results indicated that the curing reaction of the terminal ethynyl groups of the copolymers took place upon heating to 250 °C. The T_g of cured PPEKs was increased to about 260 °C. They also exhibited excellent thermal stability with 5% weight loss temperatures ranging from 448 to 527 °C in various atmospheres. The PPEKs with pendent terminal ethynyl groups were subsequently functionalized with pyrene through click reaction. A dilute chloroform solution displayed a red‐shifted emission profile. © 2014 Society of Chemical Industry     

Novel organosoluble poly(amide‐imide‐imide)s synthesized from new tetraimide‐dicarboxylic acid by condensation with 4,4′‐oxydiphthalic anhydride, 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene,trimellitic anhydride,and various aromatic diamines

A new monomer of tetraimide‐dicarboxylic acid (IV) was synthesized by starting from ring‐opening addition of 4,4′‐oxydiphthalic anhydride, trimellitic anhydride, and 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene at a 1:2:2 molar ratio in N‐methyl‐2‐pyrrolidone (NMP). From this new monomer, a series of novel organosoluble poly(amide‐imide‐imide)s with inherent viscosities of 0.7–0.96 dL/g were prepared by triphenyl phosphite activated polycondensation from the tetraimide‐diacid with various aromatic diamines. All synthesized polymers were readily soluble in a variety of organic solvents such as NMP and N,N‐dimethylacetamide, and most of them were soluble even in less polar m‐cresol and pyridine. These polymers afforded tough, transparent, and flexible films with tensile strengths ranging from 99 to 125 MPa, elongations at break from 12 to 19%, and initial moduli from 1.6 to 2.4 GPa. The thermal properties and stability were also good with glass‐transition temperatures of 236–276°C and thermogravimetric analysis 10 wt % loss temperatures of 504–559°C in nitrogen and 499–544°C in air. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2854–2864, 2006     

Cross-linkable highly halogenated poly(arylene ether ketone/sulfone)s with tunable refractive index: Synthesis, characterization and optical properties

A series of novel cross-linkable, highly halogenated poly(arylene ether ketone)s (HPAEKs) and poly(arylene ether sulfone)s (HPAESs) with different bromine contents have been designed and prepared by polycondensation reactions for use as optical waveguide materials. The method used for their preparation involved reacting decafluorodiphenyl ketone/sulfone (DFPK/DFPS) with a mixture of 4,4′-isopropylidene bis(2,6-dibromophenol) (4Br-BPA), 4,4′-(hexafluoroisopropylidene)diphenol (6F-BPA), and 1,1-bis(4-hydroxyphenyl)ethyl-1-phenyl-2,3,5,6-tetrafluorostyrol ether (BHPFS). The feed ratio of 4Br-BPA to the total bisphenols varied from 0 to 80 mol.%, while that of BHPFS remained at 20% for all polymers. The resulting polymers have excellent solubility in most common organic solvents such as tetrahydrofuran, cyclohexanone and N,N-dimethylacetamide (DMAc) and can be easily cast into optical-quality thin films. A high glass transition temperature in the range of 164-206 °C was found for these polymers, which could be further increased by about 20 °C upon thermal or photochemical cross-linking. Slab and channel waveguides have been prepared from these polymers. All of them exhibited low optical loss (0.4-0.6 dB/cm) at the telecommunication wavelength of 1550 nm. Due to the relatively higher polarizability of the C-Br bond than that of the C-H bond, an increase in the refractive index was observed as the bromine content in the polymers increased. Consequently, the refractive index of HPAEKs and HPAESs can be readily adjusted within a wide range from 1.51 to 1.57 by simply changing the ratio of the bromine-containing bisphenol in the feed. This variability, along with the excellent cross-linking capability, allows these polymers to be used as both the core and the cladding materials for the waveguide device fabrication and provides a greater flexibility in the design of device structures.     

2,2￠,6,6￠-四甲基-4,4￠-二苯氧基二苯砜、二苯醚和对苯二甲酰氯三元无规共聚物的合成与表征

以2,2￠,6,6￠-四甲基-4,4￠-二苯氧基二苯砜(o-M2DPODPS)、二苯醚(DPE)和对苯二甲酰氯(TPC)为单体，在无水AlCl3和N,N-二甲基甲酰胺(DMF)存在的条件下，于1,2-二氯乙烷(DCE)中进行低温溶液无规共缩聚，合成了一系列新型线型高分子量含双邻甲基取代结构的聚醚砜醚酮酮(DM-PESEKK)/聚醚酮酮(PEKK)无规共聚物，并用IR, DSC, XRD, TGA和1H-NMR等方法对共聚物进行了表征分析，考察了共聚物的溶解性能. 结果表明，随着DM-PESEKK含量的增加，玻璃化转变温度(Tg)逐渐升高，熔融温度(Tm)逐渐降低，结晶度下降，溶解性得到明显改善.     

Synthesis and characterisation of poly(arylene sulphides): Part 11. Preparation of poly(1,4-phenylene sulphide) directly from bis(4-bromophenyl) disulphide

Reaction conditions for the preparation of poly(1,4-phenylene sulphide) (PPS) directly from bis(4-bromophenyl) disulphide (BBD) have been established. Reactions were performed in a boiling quinoline/pyridine solvent mixture (91% by vol. quinoline) in the presence and absence of copper powder. Reaction products were fractionated and the fractions characterised using elemental analysis, IR and NMR spectroscopy, viscometry, hot-stage microscopy, differential scanning calorimetry, thermogravimetry and curing studies. The yields and properties of the polymeric fractions are compared to those of similar fractions obtained from preparation of PPS by solution polymerisation of copper(I) 4-bromobenzenethiolate under conditions which correspond to those employed in this work. PPS was not produced, and BBD was almost quantitatively recovered when copper was absent from the reactants. Reactions performed using an equimolar ratio of copper to BBD produced PPS of molar mass approximately 2–4 × 10³ gmol^?1 in 76% yield after 8h reaction. However, this PPS was contaminated with an insoluble infusible material which had a deleterious effect on the physical properties of derived cured PPS materials. The yield of PPS decreased and the quantity of contaminant increased as reaction time increased. PPS of molar mass approximately 10⁴g mol^?1 was obtained in 50–60% yield, free from insoluble infusible material, when the molar ratio of copper: BBD was increased to 2:1; it exhibited normal properties on curing.     

Synthesis,properties, and gas permeation performance of cardo poly(arylene ether sulfone)s containing phthalimide side groups

Novel bisphenol monomers ( 1a‐d ) containing phthalimide groups were synthesized by the reaction of phenolphthalein with ammonia, methylamine, aniline, and 4‐tert‐butylanilne, respectively. A series of cardo poly(arylene ether sulfone)s was synthesized via aromatic nucleophilic substitution of 1a‐d with dichlorodiphenylsulfone, and characterized in terms of thermal, mechanical and gas transport properties to H₂, O₂, N₂, and CO₂. The polymers showed high glass transition temperature in the range 230–296°C, good solubility in polar solvents as well as excellent thermal stability with 5% weight loss above 410°C. The most permeable membrane studied showed permeability coefficients of 1.78 barrers to O₂ and 13.80 barrers to CO₂, with ideal selectivity factors of 4.24 for O₂/N₂ pair and 28.75 for CO₂/CH₄ pair. Furthermore, the structure–property relationship among these cardo poly(arylene ether sulfone)s had been discussed on solubility, thermal stability, mechanical, and gas permeation properties. The results indicated that introducing 4‐tert‐butylphenyl group improved the gas permeability of polymers evidently. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Fabrication of tissue engineering scaffold from poly(vinylalcohol-co-ethylene)/poly(D,L-lactic-co-glycolic acid) blend: Miscibility,thermomechanical properties,and morphology

A series of poly(DL-lactide-co-glycolic acid) (PLGA) with poly(vinylalcohol-co-ethylene) (PEVAL) blends were prepared by solution casting method. The miscibility, thermal and mechanical properties have been investigated using FTIR, DSC, and DMA techniques. The miscibility of this pair of polymers throughout compositions was proved by these methods through the single T_g and the presence of interactions between the constituents. The TGA analysis revealed three degradation zones and no sensible enhancement in the thermal stability of PLGA was noted with addition of PEVAL content. The SEM analysis revealed that the draying method dramatically influence the surface morphology of copolymers and blend. The cross section micrograph of blend scaffold containing 50 wt% of PEVAL presents microcavities of diameter pores ranged between 70 and 170 µm interconnected and uniformly distributed in the polymer matrix.     

Synthesis and characterization of cleavable surfactants derived from poly(ethylene glycol) monomethyl ether

A series of noncyclic acetal-linked cleavable surfactants were simply prepared by condensation of aldehydes with poly(ethylene glycol) monomethyl ethers. All of the products were characterized by¹H nuclear magnetic resonance. Their hydrophile-lipophile balance, surface tension, cloud point, critical micelle concentration, and foam height were determined. Hydrolysis kinetic studies, followed by gas chromatography, showed that they had higher hydrolytic reactivity in acidic solution than cyclic acetal-linked cleavable surfactants.