Etch characteristics of IrMn thin films using an inductively coupled plasma of CH3OH/Ar

An inductively coupled plasma reactive ion etching of IrMn magnetic thin films patterned with Ti hard mask was studied in a CH₃OH/Ar gas mix. As the CH₃OH concentration increased, the etch rates of IrMn thin films and Ti hard mask decreased, while the etch profiles improved with high degree of anisotropy. The effects of coil rf power, dc-bias voltage to substrate and gas pressure on the etch characteristics were investigated. The etch rate increased and the etch profile improved with increasing coil rf power, dc-bias voltage and decreasing gas pressure. X-ray photoelectron spectroscopy revealed that the chemical reaction between IrMn films and CH₃OH gas occurred, leading to the clean and good etch profile with high degree of anisotropy of 90°.     

Evolution of etch profile in etching of CoFeB thin films using high density plasma reactive ion etching

Inductively coupled plasma reactive ion etching of CoFeB magnetic thin films patterned with Ti hard mask was studied in a CH₃OH/Ar gas mix. As the CH₃OH concentration increased, the etch rates of CoFeB thin films and Ti hard mask decreased but the etch profiles improved with high degree of anisotropy. The effects of coil rf power, dc-bias voltage and gas pressure on the etch characteristics were investigated. The etch rate increased with increasing coil rf power, dc-bias voltage and decreasing gas pressure. The degree of anisotropy in the etch profile of CoFeB films improved with increasing coil rf power and dc-bias voltage. X-ray photoelectron spectroscopy revealed that the chemical compounds containing Co and Fe components were formed during the etching. However, it was expected that the formation of these compounds could not increase the etch rates of the films due to low volatile compounds despite the improvement in etch profile.     

Investigation on etch characteristics of MgO thin films using a HBr/Ar plasma

Etch characteristics of MgO thin films were investigated using an inductively coupled plasma reactive ion etcher in a HBr/Ar plasma. As the concentration of HBr gas increased, the etch rate of MgO thin films gradually decreased, but the etch rate of Ti hard mask showed initial decrease and then increased with increasing HBr concentration. The etch profile of MgO films was improved with increasing HBr concentration and a high degree of anisotropy in etch profile was achieved at 30% HBr/Ar gas. Based on the etch characteristics and surface analysis by X-ray photoelectron spectroscopy, it can be concluded that the etch mechanism of MgO thin films in a HBr/Ar gas does not follow the reactive ion etch mechanism but the sputter etching mechanism with the assistance of chemical reactions on the film surfaces.     

Inductively coupled plasma reactive ion etching of titanium thin films using a Cl2/Ar gas

Inductively coupled plasma reactive ion etching of titanium thin films patterned with a photoresist using Cl₂/Ar gas was examined. The etch rates of the titanium thin films increased with increasing the Cl₂ concentration but the etch profiles varied. In addition, the effects of the coil rf power, dc-bias voltage and gas pressure on the etch rate and etch profile were investigated. The etch rate increased with increasing coil rf power, dc-bias voltage and gas pressure. The degree of anisotropy in the etched titanium films improved with increasing coil rf power and dc-bias voltage and decreasing gas pressure. X-ray photoelectron spectroscopy revealed the formation of titanium compounds during etching, indicating that Ti films etching proceeds by a reactive ion etching mechanism.     

Etch characteristics of CoFeB magnetic thin films using high density plasma of a H2O/CH4/Ar gas mixture

Etch characteristics of CoFeB magnetic thin films patterned with TiN hard masks were investigated using inductively coupled plasma reactive ion etching in H₂O/Ar and H₂O/CH₄ gas mixes. As the H₂O concentration in the H₂O/Ar gas increased, the etch rates of CoFeB and TiN films decreased simultaneously, while the etch selectivity increased and etch profiles improved slightly without any redeposition. The addition of CH₄ to the H₂O gas resulted in an increase in etch selectivity and a higher degree of anisotropy in the etch profile. X-ray photoelectron spectroscopy was performed to understand the etch mechanism in H₂O/CH₄ plasma. A good pattern transfer of CoFeB films masked with TiN films was successfully achieved using the H₂O/CH₄ gas mix.     

Etch characteristics of indium zinc oxide thin films using inductively coupled plasma of a Cl2/Ar gas

Inductively coupled plasma reactive ion etching of indium zinc oxide (IZO) thin films masked with a photoresist was performed using a Cl₂/Ar gas. The etch rate of the IZO thin films increased as Cl₂ gas was added to Ar gas, reaching a maximum at 60% Cl₂ and decreasing thereafter. The degree of anisotropy in the etch profile improved with increasing coil rf power and dc-bias voltage. Changes in pressure had little effect on the etch profile. X-ray photoelectron spectroscopy confirmed the formation of InCl₃ and ZnCl₂ on the etched surface. The surface morphology of the films etched at high Cl₂ concentrations was smoother than that of the films etched at low Cl₂ concentrations. These results suggest that the dry etching of IZO thin films in a Cl₂/Ar gas occurs according to a reactive ion etching mechanism involving ion sputtering and a surface reaction.     

Etch characteristics of magnetic tunnel junction stack with nanometer-sized patterns for magnetic random access memory

Etch characteristics of magnetic tunnel junction (MTJ) stack masked with TiN films were investigated using an inductively coupled plasma reactive ion etcher in Cl₂/Ar and BCl₃/Ar gases for magnetic random access memory. The effect of etch gas on the etch profile of MTJ stacks was examined. As Cl₂ and BCl₃ concentrations increased, the etch slope of etched MTJ stack became slanted and the dimensional shrinkage was observed. A high degree of anisotropic etching of MTJ stacks was achieved using Cl₂/Ar gas at the optimized etch conditions.     

The dry etching property of TiO2 thin films using metal-insulator-metal capacitor in inductively coupled plasma system

In this work, we investigated the etching characteristics of TiO₂ thin films and the selectivity of TiO₂ to SiO₂ in a BCl₃/Ar inductively coupled plasma (ICP) system. The maximum etch rate of 84.68 nm/min was obtained for TiO₂ thin films at a gas mixture ratio of BCl₃/Ar (25:75%). In addition, etch rates were measured as a function of etching parameters, such as the RF power, DC-bias voltage and process pressure. Using the X-ray photoelectron spectroscopy analysis the accumulation of chemical reaction on the etched surface was investigated. Based on these data, the ion-assisted physical sputtering was proposed as the main etch mechanism for the BCl₃-containing plasmas.     

Dry etching of magnesium oxide thin films by using inductively coupled plasma for buffer layer of MFIS structure

Magnesium oxide thin film has been widely used as a buffer layer and substrate for growing various thin film materials because of very low Gibbs free energy, low dielectric constant and low refractive index. The investigations of the MgO etching characteristics in BCl₃/Ar plasma were carried out using the inductively coupled plasma system. It was found that the increasing BCl₃ in the mixing ratio of BCl₃/Ar plasma causes monotonic MgO etch rate. The results showed in the BCl₃-rich plasma that the etching process is dominantly supplied by the chemical pathway through the ion-assisted chemical reaction.     

Etch damage characteristics of TiO2 thin films by capacitively coupled RF Ar plasmas

Etch damage of TiO₂ thin films with the anatase phase by capacitively coupled RF Ar plasmas has been investigated. The plasma etching causes a mixed phase of anatase and rutile or the rutile phase. The effect of Ar plasma etching damage on degenerating TiO₂ thin films is dependent on gas pressure and etching time. The physical etching effect at a low gas pressure (1.3 Pa) contributes to the degradation: the atomic O concentration at the thin film surface is strongly increased. At a high gas pressure (13-27 Pa) and long etching time (60 min), there are a variety of surface defects or pits, which seem to be similar to those for GaN resulting from synergy effect between particle and UV radiation from the plasmas. For the hydrophilicity, the thin film etched at the high gas pressure and a short etching time (5 min) seems to have no etch damage: its contact angle property is almost similar to that for the as-grown thin film, and is independent of the black light irradiation. This result would probably result from formation of donor-like surface defects such as oxygen vacancy.     

The etching characteristics of Al2O3 thin films in an inductively coupled plasma

In this study, the etching characteristics of ALD deposited Al₂O₃ thin film in a BCl₃/N₂ plasma were investigated. The experiments were performed by comparing the etch rates and the selectivity of Al₂O₃ over SiO₂ as functions of the input plasma parameters, such as the gas mixing ratio, the DC-bias voltage, the RF power, and the process pressure. The maximum etch rate was obtained at 155.8 nm/min under a 15 mTorr process pressure, 700 W of RF power, and a BCl₃ (6 sccm)/N₂ (14 sccm) plasma. The highest etch selectivity was 1.9. We used X-ray photoelectron spectroscopy (XPS) to investigate the chemical reactions on the etched surface. Auger electron spectroscopy (AES) was used for the elemental analysis of the etched surfaces.     

Synthesis of nitrogen-rich carbon nitride thin films via magnetic field-assisted inductively coupled plasma sputtering

Carbon nitride (CN_x) thin films were synthesized by magnetic field-assisted inductively coupled plasma (ICP) sputtering. The electron density, electron temperature and optical emission intensity of the plasma state were significantly changed by varying the external magnetic field applied. The CN_x thin film with the highest nitrogen content (N/C=1.16) was obtained when the electron density was at its highest and the electron temperature at its lowest. Additionally, the optical emission from atomic nitrogen was the strongest under the same condition.     

Dry etching of TaN thin film using CH4/Ar inductively coupled plasma

In this research, we investigated the TaN etch rate and selectivity with under layer (HfO₂) and mask material (SiO₂) in inductively coupled CH₄/Ar plasma. As the CH₄ content increased from 0% to 80% in CH₄/Ar plasma, the TaN etch rate was increased from 11.9 to 22.8 nm/min. From optical emission spectroscopy (OES), the intensities for CH [431 nm] and H [434 nm] were increased with the increasing CH₄ content from 0% to 100% in CH₄/Ar plasma. The results of x-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) showed no accumulation of etch by-products from the etched surface of TaN thin film. As a result of OES, AES and XPS analysis, we observed the etch by-products from the surfaces, such as Ta-N-CH and N-CH bonds. Based on the experimental results, the TaN etch was dominated by the chemical etching with the assistance of Ar sputtering in reactive ion etching mechanism.     

Dry etching characteristics of HfAlO3 thin films in BCl3/Ar plasma using inductively coupled plasma system

In this study, we monitored the HfAlO₃ etch rate and selectivity to SiO₂ as a function of the etch parameters (gas mixing ratio, RF power, DC-bias voltage, and process pressure). A maximum etch rate of 52.6 nm/min was achieved in the 30% BCl₃/(BCl₃ + Ar) plasma. The etch selectivity of HfAlO₃ to SiO₂ reached 1.4. As the RF power and the DC-bias voltage increased, the etch rate of the HfAlO₃ thin film increased. As the process pressure decreased, the etch rate of the HfAlO₃ thin films increased. The chemical state of the etched surfaces was investigated by X-ray Photoelectron Spectroscopy (XPS). According to the results, the etching of HfAlO₃ thin films follows the ion-assisted chemical etching mechanism.     

Highly selective dry etching of alternating phase-shift mask (PSM) structures for extreme ultraviolet lithography (EUVL) using inductively coupled plasmas (ICP)

Extreme ultraviolet lithography (EUVL) is the most promising candidate for next generation lithography due to its feature size of 32 nm or below. We investigated the etching properties of materials in an alternating, phase-shift mask (PSM) structure for EUVL, including a Ru top capping layer, Mo-Si multilayer (ML) and Ni etch stop layer (ESL), by varying the Cl₂/O₂ and Cl₂/Ar gas flow ratios, and the dc self-bias voltage (V_dc) in inductively coupled plasma (ICP). The Ru layer could be etched effectively in Cl₂/O₂ plasmas and Mo-Si ML could be etched with an infinitely high etch selectivity over Ni ESL in Cl₂/Ar plasmas, even with increasing overetch time.     

Dry etching of TiN in N2/Cl2/Ar adaptively coupled plasma

We investigated the N₂ additive effect on the etch rates of TiN and SiO₂ and etch profile of TiN in N₂/Cl₂/Ar adaptively coupled plasma (ACP). The mixing ratio of Cl₂ and Ar was fixed at 75 and 25 sccm, respectively. The N₂ flow rate was increased from 0 to 9 sccm under the constant pressure of 10 mTorr. As N₂ flow rate was increased in N₂/Cl₂/Ar plasma, the etch rate of TiN was linearly increased, but that of SiO₂ was increased non-monotonically. The etch profile and the compositional changes of TiN was investigated with field emission-scanning electron microscope (FE-SEM), FE-Auger electron spectroscopy (FE-AES) and x-ray photoelectron spectroscopy (XPS). When 9 sccm N₂ was added into Cl₂/Ar, a steep etch profile and clean surface of TiN was obtained. In addition, the signals of TiN and Ti were disappeared in FE-AES and XPS when N₂ additive flow into Cl₂/Ar was above 6 sccm. From the experimental data, the increase in TiN etch rate was mainly caused by the increase of desorption and evacuation rate of etch by products because of the increased effective pumping speed. The etch mechanism of TiN in N₂/Cl₂/Ar ACP plasma can be concluded as the ion enhanced chemical etch.     

Etch characteristics of indium zinc oxide thin films in a C2F6/Ar plasma

Dry etching of indium zinc oxide (IZO) thin films was performed using inductively coupled plasma reactive ion etching in a C₂F₆/Ar gas. The etch characteristics of IZO films were investigated as a function of gas concentration, coil rf power, dc-bias voltage to substrate, and gas pressure. As the C₂F₆ concentration was increased, the etch rate of the IZO films decreased and the degree of anisotropy in the etch profile also decreased. The etch profile was improved with increasing coil rf power and dc-bias voltage, and decreasing gas pressure. An X-ray photoelectron spectroscopy analysis confirmed the formation of InF₃ and ZnF₂ compounds on the etched surface due to the chemical reaction of IZO films with fluorine radicals. In addition, the film surfaces etched at different conditions were examined by atomic force microscopy. These results demonstrated that the etch mechanism of IZO thin films followed sputter etching with the assistance of chemical reaction.     

Amorphous hydrogenated carbon films used as masks for silicon microtips fabrication in a reactive ion etching with SF6 plasma

A room temperature fabrication process for silicon microtips has been developed using amorphous hydrogenated carbon films as masks for silicon etching. Reactive ion etching using an SF₆ plasma has been employed to sharpen the microtips without any thermal oxidation technique.     

Etch characteristics of TiN/Al2O3 thin film by using a Cl2/Ar adaptive coupled plasma

In this study, we carried out an investigation in the etching characteristics of TiN thin films in a C1₂/Ar adaptive coupled plasma. The maximum etch rate of the TiN thin films was 768 nm/min at a gas mixing ratio of C1₂ (75%)/Ar (25%). At the same time, the etch rate was measured as functions of the various etching parameters. The X-ray photoelectron spectroscopy analysis showed the efficient destruction of the oxide bonds by the ion bombardment as well as the accumulation of low volatile reaction products on the etched surface. Field emission Auger electron spectroscopy analysis was used to examine the efficiency of the ion-stimulated desorption of the reaction products.     

Comparison of dry etching of PMMA and polycarbonate in diffusion pump-based O2 capacitively coupled plasma and inductively coupled plasma

We report a comparison of dry etching of polymethyl methacrylate (PMMA) and polycarbonate (PC) in O₂ capacitively coupled plasma (CCP) and inductively coupled plasma (ICP). A diffusion pump was used as high vacuum pump in both cases. Experimental variables were process pressure (30-180 mTorr), CCP power (25-150 W) and ICP power (0-350 W). Gas flow rate was fixed at 5 sccm. An optimized process pressure range of 40-60 mTorr was found for the maximum etch rate of PMMA and PC in both CCP and ICP etch modes. ICP etching produced the highest etch rate of 0.9 μm/min for PMMA at 40 mTorr, 100 W CCP and 300 W ICP power, while 100 W CCP only plasma produced 0.46 μm/min for PMMA at the same condition. For polycarbonate, the highest etch rates were 0.45 and 0.27 μm/min, respectively. RMS surface roughnesses of PMMA and PC were about 2-3 nm after etching. Etch selectivity of PMMA over photoresist was 1-2 and that of PC was less than 1. When ICP power increased from 0 to 350 W, etch rates of PMMA and PC increased linearly from 0.47 to 1.18 μm/min and from 0.18 to 0.6 μm/min, while the negative self bias slightly reduced from 364 to 352 V. Increase of CCP power raised both self bias and PMMA etch rate. PMMA etch rates were about 3 times higher than those of PC at the same CCP conditions. SEM data showed that there was some undercutting of PMMA and PC after etching at 300 W ICP, 100 W CCP and 40 mTorr. The results also showed that the etched surface of PMMA was rough and that of PC was relatively smooth.