2014合金的回归再时效

本文采用拉伸实验和透射电镜法,研究了2014铝合金的回归再时效(RRA)处理.结果表明:采用欠时效(100℃(2×2h)与适当回归处理(200×5min)配合的RRA处理,可同时提高2014合金的强度和塑性.适当的回归处理能使欠时效2014合金组织中部分GP区优先长大.随后再进行峰时效处理,不仅能改善晶界析出相的尺寸和分布,而且还能使基体析出相尺寸产生明显的差异.这种尺寸有明显差异的基体析出相协同强化有利于提高2014合金的强韧性.     

双级时效制度对7150铝合金微观组织和性能的影响

采用拉伸测试、电导率测试和透射电镜等手段研究了双级时效制度对7150铝合金的力学性能、电导率和微观组织的影响。结果表明:在本研究范围内,第一级时效制度对合金的力学性能和电导率影响不大;合金经过120℃/8h+160℃/6h,可以达到与单级峰时效处理相当的抗拉强度,并且电导率有明显提高;第二级时效温度为168℃时效时,相比在160℃进行第二级时效,合金在具有同等电导率水平时,损失的强度相对较多,但时效时间明显变短;120℃/8h+160℃/32h双级时效后,合金的抗拉强度为560MPa,屈服强度为520MPa,延伸率为11.5%,电导率22.7MS.m-1,晶内沉淀析出相以η′和η为主,晶界析出相完全断开。     

基于厚向组织性能考量的7B50铝合金中厚板回归再时效热处理

为解决T6态高强铝合金强度高而耐蚀性难以满足使用需求，采用三级时效工艺来改善析出强化相特别是晶界析出相的形貌、尺寸、分布等，并通过研究不同回归处理制度对组织、性能的影响而获得适宜7B50铝合金中厚板的三级时效工艺.研究发现提高回归温度或延长回归时间均会使中厚板心部及表层组织的晶内和晶界析出相发生粗化并析出稳定η-MgZn₂相，导致强度下降、电导率上升，其中回归温度对强度和电导率的影响显著.三级时效处理虽使晶内析出相尺寸有所增加，但却使T6态连续分布的晶界析出相呈断续分布，结合心部和表层强度及电导率测量结果认为合适的回归处理制度为165℃/6 h.然而，热轧引起中厚板表层较心部更为严重的变形使表层含有更多的亚晶或亚结构且其分布更均匀，从而使表层更快到达峰时效，进一步的回归再时效处理则使表层析出更多稳定η相，而η相的形成与晶内析出相的粗化长大是造成表层和心部强度差异的关键.虽然淬火/三级时效态表层和心部的晶粒结构存在差异，且局部出现亚晶合并长大，但其对强度的提升效果远低于表层析出稳定η相所引起的强度下降.可见，三级时效工艺并不能缓解7B50铝合金中厚板心部和表层的性能差异，但可使表层和心部的强度、电导率满足某实际工况要求.      

回归再时效对超高强铝合金力学性能及组织的影响

在传统的回归再时效(retrogression and re-aging,RRA)工艺(峰时效)基础上降低预时效或再时效温度,对Fe和Si杂质含量高的超高强Al-Zn-Mg-Cu合金挤压棒材进行RRA处理,通过拉伸性能和疲劳性能测试以及扫描电镜和透射电镜观察,研究RRA工艺对合金力学性能与组织的影响。结果表明:降低预时效或再时效温度都可明显提高该合金的塑性和抗疲劳损伤性能,略微降低合金的抗拉强度。采用峰时效温度(120℃)RRA处理后的合金,晶内的主要析出相为尺寸较大的η′相,不能被位错切割,合金强度较高(674 MPa),但塑性和抗疲劳损伤性能差,伸长率为11.1%,最终应力强度因子幅值ΔK=26.8 MPa·m1/2;降低时效温度可增加析出相中GP区粒子的比例,减小η′相的尺寸,从而提高塑性变形能力以及抗疲劳损伤性能。     

双级时效对Mg-2.8Nd-0.4Zn-0.5Zr合金微观组织和力学性能的影响

采用OM、SEM、TEM以及硬度测试和拉伸力学性能测试等手段,研究了双级时效对Mg-2.8Nd-0.4Zn-0.5Zr合金显微组织和力学性能的影响。结果表明,合金经260℃/30 min+200℃/4 h双级时效处理后,其抗拉强度和屈服强度较200℃/14 h单级时效合金分别提高23 MPa和20 MPa,并且达到硬度峰值所需时间缩短9.5 h。主要是由于第一级高温预时效过程中析出β1相,在第二级时效过程中,β1相保留,同时又析出β″相,并且β″相尺寸较单级时效后的合金更细小。在两种析出相同时作用的情况下,其强化效果明显优于单一β″相强化的单级时效处理。     

时效工艺对低铍铜力学性能与电导率的影响

通过力学性能、电导率测定和显微组织观察，研究了常规时效和分级时效对铍青铜性能的影响；结果表明0．5mm厚的C17460铍青铜板经900℃／5min固溶处理后分级时效的适宜工艺条件为：低温320℃／150min、高温465℃／120min，此工艺条件下合金的抗拉强度可达724MPa。电导率可达41．9IACS％；常规时效的适宜工艺条件为：450℃／150min，此工艺条件下合金的抗拉强度可达721MPa,电导率可达41．4IACS％。两种时效制度下均未出现明显的晶界反应。     

Al-5.87Zn-2.07Mg-2.42Cu合金形变热处理过程的组织与性能演变

通过维氏硬度试验、力学性能试验以及透射电镜观察,研究了Al-5.87Zn-2.07Mg-2.42Cu合金在最终形变热处理(固溶—预时效—变形—终时效)过程中的组织演变和力学性能,并优化出最适宜的工艺制度。结果表明,Al-5.87Zn-2.07Mg-2.42Cu合金最适宜的形变热处理工艺为480℃/1 h+100℃/8 h+30%+120℃/10 h。100℃/8 h预时效处理后,合金基体内弥散析出大量细小的沉淀相。经30%冷变形引入位错后进行120℃/10 h终时效处理,析出相数量增多且尺寸增大。最终形变热处理后合金的硬度、抗拉强度和屈服强度分别为200 HV、645 MPa和621MPa,分别比T6态合金的增加了19 HV、67 MPa和110 MPa。     

时效工艺对新型超高强高韧7A56铝合金厚板组织和性能的影响

研究了单级时效和三级时效工艺对新型超高强高韧7A56铝合金厚板组织和性能的影响。采用透射电镜、布氏硬度计、金属材料断裂韧度实验机、热差扫描仪以及多功能拉伸实验机等多种检测仪器,对7A56铝合金厚板在不同时效工艺下的组织和性能进行了表征与测试。结果表明：7A56铝合金厚板单级峰值时效工艺为120℃/24 h,抗拉强度达到636 MPa,断裂韧性达到26.12 MPa·m^1/2;三级时效工艺可以有效提升7A56铝合金厚板强度与韧性的匹配程度,三级时效制度为120℃/24h+175℃/90 min+120℃/24 h,抗拉强度达到626 MPa,断裂韧性达到31.56 MPa·m^1/2。     

低温轧制及时效热处理对Al-Zn-Mg铝合金显微组织与性能的影响

对固溶淬火态的Al-Zn-Mg合金板材分别采用CR(cryogenicrolling,低温轧制)+480 h自然时效,CR+100℃/12 h时效,CR+100℃/80 h时效,以及未经CR直接100℃/107h时效等4种工艺进行处理,测定合金的硬度和室温拉伸性能,并进行剥落腐蚀和电化学腐蚀实验,采用金相显微镜、扫描电镜以及透射电镜等观察合金的形貌与组织,研究低温轧制和时效热处理工艺(自然时效和不同人工时效时间)对Al-Zn-Mg合金组织与性能的影响。结果表明:与直接进行100℃/107 h时效处理的合金相比,CR+480 h自然时效和CR+100℃/12 h人工时效态合金的抗剥落腐蚀性能和电化学腐蚀性能较差,其主要原因是低温轧制后形成了亚微米级、呈纤维状且高位错密度的超细晶粒。而CR+100℃/80 h时效处理合金具有更好的抗剥落腐蚀性能和电化学腐蚀性能,其主要原因是低温轧制形成高密度位错,并在100℃/80 h时效处理过程中形成更加粗大且不连续分布的晶界析出相。另外,低温轧制处理后形成的高密度位错的超细晶组织,可显著加速时效硬化响应。     

热处理对添加少量Cr、Fe的Ti-Ni合金组织和力学性能的影响

采用真空熔炼法制备Ti_(45)Ni_(55)Cr_(0.3)和Ti_(45)Ni_(52)Fe_3合金(元素含量为摩尔分数)铸锭,对其进行均匀化处理以及850℃/1 h固溶和水淬后,分别采用3种不同的工艺进行热处理:1)850℃/1 h固溶,2)375℃/1 h时效,3)25%冷轧+375℃/1 h退火,研究热处理工艺对合金的相变特性、力学性能、内耗性能和微观组织的影响。结果表明,Ti_(45)Ni_(55)Cr_(0.3)和Ti_(45)Ni_(52)Fe_3合金的基体均由B2与R相组成;Ti_(45)Ni_(55)Cr_(0.3)合金经过375℃/1 h时效或25%冷轧+375℃/1 h退火处理后,析出Cr3Ni2粒子,时效后抗拉强度为1 385 MPa,时效升温过程的峰值内耗达到0.53;Ti_(45)Ni_(52)Fe_3合金经过25%冷轧+375℃/1 h退火后析出Ti3Ni4相,抗拉强度为770 MPa;与其它热处理工艺的升温过程相比,Ti_(45)Ni_(52)Fe_3合金的时效升温过程峰值内耗最高,达到0.158;降温过程中,Ti_(45)Ni_(55)Cr_(0.3)合金在时效降温过程中发生B2→R→M相变,退火的降温过程中发生B2?R相变,而Ti_(45)Ni_(52)Fe_3合金在退火的降温过程中发生B2→R→M相变。     

The effect of amount of possession of the trait of hostility on accuracy of perception of hostility in others.

Some theories of personality hold that an individual's perception of others is influenced by his own personality characteristics; more specifically, that a trait of low social value will be projected more into others, and that insight into the possession of these characteristics reduces this distortion. These 2 hypotheses were tested by having a group of college students rate each other (including themselves) on degree of friendliness or hostility. Agreement with group rating about self yielded the insight score. In general, the hypotheses were supported; the "friendly" Ss were most accurate in their perception of others, and insight was positively associated with accurate perception. From Psyc Abstracts 36:04:4HL16M. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Comparison of rates of infection of two methods of emergency ventricular drainage

The rates of infection of two methods of external ventricular drainage in use at Atkinson Morley's Hospital--namely, (a) percutaneous drainage with Rickham reservoirs and (b) tunnelled ventriculostomies--were compared in this retrospective review. Percutaneous drainage of CSF with Rickham reservoirs was associated with a 27% rate of infection as identified by positive microbiological cultures; tunnelled ventriculostomy catheters had a 10% infection rate. The difference in the infection rate between the two methods was statistically significant (P < 0.015). Other variables examined, including the age and sex of the patients and the reasons for ventricular drainage, were not associated with an increased rate of infection. Most infections from either method were caused by a coagulase negative staphylococcus. The average duration of ventricular drainage before identification of positive cultures was 5.7 days for Rickham reservoirs and 6.0 days for ventriculostomies.     

浅析《野草》的版画特征

鲁迅先生一生热爱美术作品,对版画中木刻兴趣尤甚.<野草>作为其"写心之作",亦呈现出一些与木刻版画一致的审美特征:一是具有木刻版画的色彩特征,多对比、多冷色,有阴郁的美感;二是具有木刻版画的力度特征,环境描写、人物刻画处处刀锋毕现,遒劲有力,有一种"力之美".     

四辊破碎机车刀架的改造

针对四辊破碎机车刀架车削中存在的几个问题,详细介绍了电动车刀架的结构和工作原理,建立主要设计参数的数学表达式,并进行适当的分析。改造后,这种电动车刀架运行平稳、可靠、方便、省力,取得了预期的效果。     

转炉炉壳热应力分析

根据实际转炉建立实体模型。以有限元为手段,考虑了炉衬和炉壳材料的物性参数随温度变化的特点和炉衬与炉壳之间膨胀间隙,计算了转炉炉壳在温度载荷和炉衬膨胀压力同时作用下的热应力。所得结果可为转炉炉壳设计提供依据。     

Comparison of the results of surgical and conservative treatment of fractures of the diaphysis of the tibia

In this paper is treated the fundamental problematic of the fracture of the diaphysis of the tibia and the therapeutic results after the conservative and operative treatment are confronted. Among 518 patients with 433 open fractures and 35 with closed fractures of the diaphysis of the tibia, successful treatment of more 2/3 was obtained in the period from 1968 to 1972. Following our casuistics and literature, whose results are similar, we find out that the average total treatment of the osteosynthesis of the fracture of the diaphysis was shortened for 2,5 months depending upon the type and the localisation of the fracture. Apolied methods of the operative and conservative and conservative treatment in relation to the velocity of the medical cure as well as to the extreme anatomical-functional results are analised. We noticed that osteosynthesis, made by the intermedullary nail and the extension of the canals or by a small AO table, by the achieved stability makes conditions of immediate motions and an early rehabilitation. Because of that it gives the best functional results.     

Results of treatment of cancer of the cardia

Cancer of the cardia is traditionally discussed with cardiac cancer of the lower portion of the esophagus and upper gastric cancer invading the esophagus, and the specific characteristics of cancer of the cardia have never been clearly defined. We reviewed the outcome of 172 patients with adenocarcinoma of the cardia who had undergone radical surgery between 1949 and 1994 in the Division of Gastrointestinal Surgery of the Cancer Institute Hospital. The centers of the tumors were located within 2 cm above and below the boundary between the esophagus and the stomach, and their longitudinal diameter was less than 8 cm. We divided the patients into an early period (1949-1979; n = 79) and a late period (1980-1994; n = 93), and focused on the historical transition. There were no differences in patient gender or histology between the two periods. However, the late period was associated with fewer cases of esophageal invasion and shorter longitudinal diameter, as the age of the population advanced. The number of advanced cancers such as the localized and infiltrative type had decreased, and early cancer and early clinical stage had become more common, but despite the fact that the number of early cancers had increased, extended dissection, such as thoracic and paraaortic lymph node dissection, was performed more frequently. By clinical stage, the long-term outcome markedly improved in Stage I patient in the late period, and tended to improve in Stage II and III patients. This appears to have been attributable to the prevention of micrometastasis by extended dissection, although the number of early cancers is another major potential cause. There were no differences in the outcome of Stage IV patients between the two periods, and further advances in multimodality therapy must be awaited. The range of resection is basically proximal gastrectomy, and if there are adequate indications, the prognosis is favorable. In view of the status of lymphatic flow and lymph node metastasis, and long-term results, lateroaortic lymph node dissection is important. Since the number of early cancer patients has been increasing, if intraabdominal recurrence is prevented, intrathoracic lymph node dissection will contribute greatly to the outcome of such patients.     

焦炭热性能指标意义浅析

通过对焦炭在高炉内的历程及其变化规律的剖析,阐述焦炭热性能指标的意义,形象地把焦炭在高炉内的损耗分为三部分(M1,M2,M3)。指出M2对焦比及焦炭价格有一定的指导作用。     

参与式农业基地建设行动方案设计

为了编制实用性强的基地建设行动方案,首先,确定参与式发展的主体,搭建一个"决策框架";其次,针对行动目标,提出不同参与主体,如管理者、农民、消费者等团队与个人的目标及行动内容;最后,工作应向重塑伙伴式合作关系,挖掘农民自我发展潜力,完成三大角色的转换,打造农业基地文化等方向推进.