纳米N掺杂TiO2的制备及可见光催化活性研究

N-doped TiO2 nanoparticle photocatalysts were prepared through a sol-gel procedure using NH4C1 as the nitrogen source and followed by calcination at certain temperature. Systematic studies for the preparation parameters and their impact on the structure and photocatalytic activity under ultraviolet （UV） and visible light irra-diation were carried out. Multiple techniques （XRD, TEM, DRIF, DSC, and XPS） were commanded to characterize the crystal structures and chemical binding of N-doped TiO2. Its photocatalytic activity was examined by the deg- radation of organic compounds. The catalytic activity of the prepared N-doped TiO2 nanoparticles under visible light （λ〉400nm） irradiation is evidenced by the decomposition of 4-chlorophenol, showing that nitrogen atoms in the N-doped TiO2 nanoparticle catalyst are responsible for the visible light catalytic activity. The N-doped TiO2 nanoparticle catalyst prepared with this modified route exhibits higher catalytic activity under UV irradiation in contrast to TiO2 without N-doping. It is suggested that the doped nitrogen here is located at the interstitial site of TiO2 lattice.     

Synthesis and catalytic activity of SBA-15 supported catalysts for styrene oxidation

Cu(II) and Mn(II) metals embedded on mesoporous SBA-15 were synthesized by co-precipitation technique.The support and catalysts were characterized by SEM–EDX,TEM,BET,XRD and ICP-AES methods.The catalytic activity of these catalysts was evaluated for styrene oxidation at various reaction conditions such as styrene to TBHP mole ratio,temperature,catalyst amount by using TBHP as an oxidizing agent.Major reaction products were styrene oxide and benzaldehyde and highest styrene conversion(97.3%) was observed at styrene to TBHP mole ratio of 1:4,temperature at 80 °C and 20 mg of catalyst.Further,the recyclability of the catalysts was observed and found that they can be recycled three times without major loss in their activity and selectivity.     

Preparation of TiO2 Nanoparticles Coated Cotton Fibers at Low Temperature and Their Photocatalytic Activity

TiO_2 nanoparticles coated cotton fiber composite was successfully prepared by using a sol-gel method at low temperature(about 100℃) using tetrabutyl-titanate [Ti(OBu)_4] as raw material.The preparation of the TiO_2 colloid and the composite were described.The properties of resulting materials were characterized by SEM and XRD,the photocatalytic degradation performance was tested using methylene blue(MB) as the target pollutant in aqueous solution.The results showed that the amorphous TiO_2 nanoparticles were distributed evenly on the outer surfaces of cotton fibers,which shows efficient photocatalytic properties when exposed to UV light,the degradation rate of MB reached 95.35% under the conditions of catalyst dosage 2.5 g/L,MB concentration 50 mg/L,irradiation time 120 min,and pH 10,and the photocatalytic activity of TiO_2/cotton fibers remained above 90% of its activity as-prepared after being used four times,the degradation rate of MB could reach 88.78% when irradiation time was 120 min.The photocatalytic degradation of MB could be properly described by the first-order kinetic law.By comparison of the removal rates of MB with and without UV light,it could be affirmed that the disappearance of MB was due to photodegradation rather than adsorption on cotton fibers.     

侧光光纤引导的内源可见光催化降解亚甲基蓝(英文)

The side-glowing optical fibers (SOFs) were chosen as the conducting medium of endogenous light; and 20 mg·L-1 methylene blue was chosen as the target to be degraded. The SOF is made up of quartz core with a silicon cladding, which can emit light through side surface more uniformly and transmit light for longer distance to avoid attenuation of light by liquid medium. The filament lamp was chosen as visible light source. Different reaction conditions, such as the presence of optical fiber or not, the quantity of SOF, light irradiation intensity were tested by measuring the methylene blue degradation of methylene blue. The results show that suitable reaction conditions were 1.167 g·L-1 Ag + /TiO 2 with 7% (by mass) of Ag + doped in TiO 2 , and 500 roots of SOF (30 cm length in solution). The photocatalytic degradation efficiency under 300W lamp irradiation for 8h was about 97%. And the photocatalytic degradation efficiency of methylene blue degradation was proportional to SOF quantity, light irradiation intensity and catalytic dosage within a certain range. Compared with general UV and visible light SOFs could save a huge amount of energy and cost, in the potential applications in dealing with organic pollutants on a large scale.     

由天然沸石和二氧化钛制备的功能材料光催化抑制水中粪肠球菌活性简

The functional materials based on natural zeolite （clinoptilolite）, TiO2-zeolite and Ag-TiO2-zeolite have been successfully synthesized by solid-state reaction in fast-hydrothermal conditions. The obtained functional materials were investigated by X-ray diffraction （XRD）, FT-1R （Fourier transform infrared） spectroscopy, DRUV-VIS （diffuse reflectance ultraviolet-visible） spectroscopy, BET （Brunauer-Emmett-Teller） and SEM/EDX （scanning electron microscope/energy dispersive X-ray spectrometer） analyses. The XRD results indicated that the clinoptilolite structure has a good thermal stabilization after the fast-hydrothermal treatment. Also, the high specific surface area about 92.55 m^2.g^-1 was noticed for Ag-TiO2-zeolite functional material. The presence of dopants was evidenced from EDX spectra. The enhanced bactericidal activity of Ag-TiO2-zeolite catalyst is proved through damaging of Enterococcusfaecalis colonies under visible irradiation, at different material doses and irradiation times.     

化学修饰Novozym-435酶催化合成维生素E琥珀酸酯的研究

Vitamin E succinate was synthesized in organic solvents using a modified Novozym-435 as catalyst.In order to improve the catalytic performance of Novozym-435,the enzyme was modified using acetic anhydride, propionic anhydride and succinic anhydride separately.We found that both the hydrolytic activity and the thermal stability of the modified Novozym-435 were enhanced compared with the unmodified enzyme.The modified Novozym-435 catalysts were used to synthesize the succinate derivative of vitamin E.Compared with the native Novozym-435,the catalytic activity of the modified novozym-435 in promoting the synthesis of vitamin E succinate was dramatically increased,with the novozym-435 modified with succinic anhydride(N435-S)as the most active catalyst.Conditions for the synthesis of vitamin E succinate were also optimized.A mixture of tert-butanol and DMSO(volume ratio of 2︰3)was the most suitable medium for the reaction,whereas the appropriate molar ratio of vitamin E to succinic anhydride and reaction temperature were 1︰5 and 40°C,respectively.Under these reaction conditions,the yield of vitamin E succinate reached 94.4%.N435-S could be reused for five batches.     

Structure,photocatalytic and antibacterial activity study of Meso porous Ni and S co-doped TiO_2 nano material under visible light irradiation

Undoped and Ni–S co-doped mesoporous TiO_2 nano materials were synthesized by using sol–gel method.The characteristic features of as prepared catalyst samples were investigated using various advanced spectroscopic and analytical techniques. The characterization results of the samples revealed that all the samples exhibited anatase phase(XRD), decreasing band gap(2.68 eV)(UV–Vis-DRS), small particle size(9.2 nm)(TEM), high surface area(142.156 m~2·g~(-1))(BET), particles with spherical shape and smooth morphology(SEM); there is a frequency shift observed for co-doped sample(FT-IR) and the elemental composition electronic states and position of the doped elements(Ni and S) in the TiO_2 lattice analyzed by XPS and EDX. These results supported the photocatalytic degradation of Bismarck Brown Red(BBR)achieved with in 110 min and also exhibited the antibacterial activity on Staphylococcus aureus(MTCC-3160), Pseudomonas fluorescence(MTCC-1688) under visible light irradiation.     

MoVPO型催化剂上氨氧化合成2-氰基吡嗪

The mechanism of 2-cyanopyrazine prepared from 2-methylpyrazine （2-MP） by catalytic ammoxidation has been explained by the theory of appropriate structure of group. A new catalyst of MoVPO was developed. The effects of catalyst promoter phosphorus and supports were investigated. The catalyst containing P, V and Mo in molar ratio of 1.4 ： 1 ： 0.02 and supported on activated alumina and prepared by impregnation method exhibits good activity and selectivity. Reaction factors such as reaction temperature, space velocity, feed composition and service life of catalyst were investigated. Optimum reaction conditions （the volume space velocity of 0.2h-1, the reaction temperature of 380 ~C and molar ratio of 1 ： 7.8 ： 8 ： 8 for 2-MP, water, oxygen and ammonia） were obtained. Selectivity of 93% and yield of 86% could be achieved under these conditions.     

Simultaneous Synthesis of Dimethyl Carbonate and Poly（ethylene terephthalate） Using Alkali Metals as Catalysts

Dimethyl carbonate （DMC） and poly（ethylene terephthalate） was simultaneously synthesized by the transesterification of ethylene carbonate （EC） with dimethyl terephthalate （DMT） in this paper. This reaction is an excellent green chemical process without poisonous substance. Various alkali metals were used as the catalysts. The results showed alkali metals had catalytic activity in a certain extent. The effect of reaction condition was also studied. When the reaction was carded out under the following conditions： the reaction temperature 250℃, molar ratio of EC to DMT 3 ： 1, reaction time 3h, and catalyst amount 0.004 （molar ratio to DMT）, the yield of DMC was 68.9%.     

La2O3助剂对甲烷干燥重整催化剂 Ni-γ-Al2O3支撑作用的研究简

The nature of support and type of active metal affect catalytic performance. In this work, the effect of using La203 as promoter and support for Ni/γ-A1203 catalysts in dry reforming of methane was investigated. The reforming reactions were carried out at atmosphenc pressure in the temperature range of 500-2700℃. The activity and stability of the catalyst, carbon formation, and syngas （H2/CO） ratio were determined. Various techniques were applied for characterization of both fresh and used catalysts. Addition of La2O3 to the catalyst matrix improved the dispersion of Ni and adsorption of CO2, thus its activity and stability enhanced.     

处理温度对锐钛型TiO2光催化活性的影响及利用可见光降解甲基紫

高温处理锐钛型TiO2可以使其转晶以改变晶型比例,因此加热温度和加热时间是影响TiO2光催化活性的主要因素.本研究中,以该方法得到了可利用可见光的TiO2催化剂,并进行了可见光降解甲基紫的研究.结果表明,在TiO2和可见光共同作用下,甲基紫的光降解效果明显优于单独使用锐钛型、金红石型和按照转晶的比率混合的锐钛型和金红石型TiO2.5.0小时的照射其降解率即可达到94.2%以上.而相同条件下,采用锐钛型、金红石型和按照转晶的比率混合的锐钛型和金红石型TiO2降解率分别只有55.82%、51.20%和40.47%.     

镧、碳共掺杂TiO2的制备及其可见光催化性能

为了更有效地利用太阳能,以钛酸丁酯为前驱体,硝酸镧和四丁基氢氧化铵为掺杂离子给体,通过改进的溶胶-凝胶法,成功制备了纯TiO₂和不同掺杂浓度的镧、碳掺杂和共掺杂TiO₂光催化剂.表征结果显示,共掺杂催化剂为锐钛矿型,具有较高的比表面积,感光范围拓展到可见光区.分别以甲基橙、罗丹明B和4-氯酚为降解物,氙灯、太阳光和自然光为光源,进行催化剂的光催化降解实验,结果表明,共掺杂催化剂活性高于未掺杂和单掺杂催化剂.降解结果显示,当共掺杂催化剂含0.5% La³⁺(摩尔比)、焙烧温度在500℃时具有最高的光催化降解效率.共掺杂TiO₂具备较高的可见光催化活性原因可能是碳掺杂降低了TiO₂禁带宽度,而镧掺杂同时维持了体系的电荷平衡.     

SnxZn(1-x)WO4光催化剂的水热合成及其可见光催化活性

采用水热合成法制备新型可见光催化剂Sn_xZn_(1-x)WO₄，以甲基橙染料废水为探针污染物，考察Zn²⁺与Sn²⁺物质的量比、水热温度和水热时间对Sn_xZn_(1-x)WO₄光催化剂的催化活性、表面形貌和比表面积的影响。结果表明，在Zn²⁺与Sn²⁺物质的量比为0.25、水热温度100 ℃和水热时间12 h条件下，合成的Sn_0.8Zn_0.2WO₄催化剂活性最好，光照30 min后，对甲基橙染料的脱色率达98.62%，较SnWO₄催化剂(合成条件为原始pH值，160 ℃水热反应24 h)提高46.66%。采用水热合成法制备的催化剂Sn_xZn_(1-x)WO₄具有良好的可见光活性。     

处理温度对锐钛型TiO2光催化活性的影响

高温处理锐钛型TiO2可使其转晶改变晶型比例,因此加热温度和加热时间是影响TiO2光催化活性的主要因素。通过该方法得到了可利用可见光的TiO2催化剂,并进行了可见光降解有机染料乙基紫的研究。结果表明,在TiO2和可见光共同作用下,乙基紫的光降解效果明显优于单独使用锐钛型、金红石型和按照转晶的比率混合的锐钛型和金红石型TiO2。     

BiOCl/g-C3N4异质结催化剂可见光催化还原CO2

以KCl、Bi（NO₃）₃和类石墨氮化碳（g-C₃N₄）为前体,采用水热法成功制备了BiOCl/g-C₃N₄异质结光催化剂,并进行可见光催化还原CO₂,考察了催化剂的活性及稳定性,同时研究BiOCl：g-C₃N₄（摩尔比）、催化剂用量和光照强度对光催化还原CO₂的影响。结果表明,在水蒸气的存在下,BiOCl/g-C₃N₄较纯BiOCl和g-C₃N₄具有更高的光催化还原CO₂活性,在催化剂用量为0.1 g,光照强度为2.413×10^-6 einstein·min^-1·cm^-2,BiOCl：g-C₃N₄摩尔比为1：1的异质结催化剂显示了最高的光催化还原CO₂活性,且可见光催化剂在5次套用实验后其活性基本不变。基于X射线衍射（XRD）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）、X射线光电子能谱（XPS）、比表面积测试（BET）和紫外-可见（UV-vis）吸收光谱表征,可以推断BiOCl和g-C₃N₄之间形成的p-n结能有效分离光生电子和空穴,是增强光催化剂活性的主要原因。     

Synthesis and visible‐light‐derived photocatalysis of titania nanosphere stacking layers prepared by chemical vapor deposition

BACKGROUND: In this study, visible‐light‐derived photocatalytic activity of metal‐doped titanium dioxide nanosphere (TS) stacking layers, prepared by chemical vapor deposition (CVD), was investigated. The as‐grown TS spheres, having an average diameter of 100–300 nm, formed a layer‐by‐layer stacking layer on a glass substrate. The crystalline structures of the TS samples were of anatase‐type. RESULTS: Ultraviolet (UV) absorption confirmed that metallic doping (i.e. Co and Ni) shifted the light absorption of the spheres to the visible‐light region. With increasing dopant density, the optical band gap of the nanospheres became narrower, e.g. the smallest band gap of Co‐doped TS was 2.61 eV. Both Ni‐ and Co‐doped TS catalysts showed a photocatalytic capability in decomposing organic dyes under visible irradiation. In comparison, Co‐doped TiO₂ catalyst not only displays the adsorption capacity, but also the photocatalytic activity higher than the N‐doped TiO₂ catalyst. CONCLUSION: This result can be attributed to the fact that the narrower band gap easily generates electron–hole pairs over the TS catalysts under visible irradiation, thus, leading to the higher photocatalytic activity. Accordingly, this study shed some light on the one‐step efficient CVD approach to synthesize metal‐doped TS catalysts for decomposing dye compounds in aqueous solution. Copyright © 2010 Society of Chemical Industry     

Ag/Bi2 WO6的制备及光催化氧化性能

以Bi（NO3）3·5H2O、 Na2WO4·2H2O、 AgNO3为原料,利用液相沉淀法制备Bi2WO6及Ag掺杂Bi2WO6光催化剂,以亚甲基蓝溶液为目标降解物,对其降解效率进行研究。研究结果表明,当亚甲基蓝溶液的浓度为15 mg/L,体积为50 mL,降解时间3.5 h, Bi2 WO6降解率仅为55%;当Ag/Bi摩尔比为0.4%时, Ag/Bi2 WO6表现出较好的催化性能,相同时间降解率达到97%。     

AgBr/Zn3(OH)2V2O7·2H2O可见光催化降解亚甲基蓝溶液

采用水热和沉淀两步合成法制备AgBr/Zn₃(OH)₂V₂O₇·2H₂O催化剂,研究其在可见光下降解亚甲基蓝溶液的性能,并考察催化剂用量、亚甲基蓝溶液初始浓度、pH值以及盐浓度对光催化性能的影响,评价AgBr/Zn₃(OH)₂V₂O₇·2H₂O催化剂的重复使用性能。结果表明,在前驱液pH为10、120 ℃水热10 h、Ag与Br物质的量比为0.20条件下制备的复合催化剂在可见光下反应120 min后,1.0 g·L^-1的催化剂对10 mg·L^-1的亚甲基蓝溶液脱色率达到85.2%。NaCl对亚甲基蓝的降解起抑制作用,Na₂SO₄对亚甲基蓝的降解起促进作用。催化剂重复使用4次后,光照120 min后的亚甲基蓝溶液脱色率可达66.4%。催化剂对不同初始浓度亚甲基蓝溶液的光催化降解符合一级动力学模型。     

Photocatalytic reduction of the environmental pollutant Cr over a cadmium sulphide powder under visible light illumination

The photocatalytic reduction of the pollutant Cr^VI over CdS in different crystalline states under visible light illumination was investigated. The photocatalytic activity of heat-treated (HT) and non-heat-treated (NHT) CdS was systematically compared. The Cr^VI, contained in an aqueous solution of 200 μg/ml, was almost totally eliminated within 30 min when NHT CdS was used as catalyst and displayed a much higher activity than that of HT CdS. The addition of a hole-scavenger such as ethanol, which acted optimally at 10–20%, remarkably improved the activity of HT CdS. The macroscopic difference in photocatalytic activity between NHT and HT CdS was microscopically explained by the differences in their morphological structures, surface states, and light responses which were determined by means of X-ray diffraction, static adsorption and UV-visible spectra. The adsorbance and adsorption state of Cr^VI was determined on the CdS surface and its photoreducibility was proven by X-ray photoelectron spectroscopy and temperature-programmed desorption. The photoreduction rate of pollutant Cr^VI, either during experiments indoors or during experiments in sunlight was remarkably improved. 99.3% of the Cr^VI was reduced from a solution of 200 μg/ml concentration during 1 h of sunlight irradiation. Applications are given for the photocatalytic elimination of Cr^VI in waste water under sunlight irradiation.     

Photocatalytic activity of undoped and sulfur-doped TiO2 films grown by MOCVD for water treatment under visible light

Titanium dioxide ceramic coatings have been used as catalysts in green technologies for water treatment. However, without the presence of a dopant, its photocatalytic activity is limited to the ultraviolet radiation region. The photocatalytic activity and the structural characteristics of undoped and sulfur-doped TiO₂ films grown at 400 °C by metallorganic chemical vapor deposition (MOCVD) were studied. The photocatalytic behavior of the films was evaluated by methyl orange dye degradation under visible light. The results suggested the substitution of Ti⁴⁺ cations by S⁶⁺ ions into TiO₂ structure of the doped samples. SO₄^2? groups were observed on the surface. S-TiO₂ film exhibited good photocatalytic activity under visible light irradiation, and the luminous intensity strongly influences the photocatalytic behavior of the S-TiO₂ films. The results supported the idea that the sulfur-doped TiO₂ films grown by MOCVD may be promising catalysts for water treatment under sunlight or visible light bulbs.