失活钙基吸收剂环境中自活化机理

将经历多次循环后失活的钙基吸收剂置于环境中吸水自活化,通过XRD分析了自活化过程吸收剂物相演变规律,在双固定床反应器系统上分析了吸水率对失活钙基吸收剂循环捕集CO₂性能的影响规律, 通过SEM和N₂吸附分析了自活化提高钙基吸收剂循环碳酸化转化率的机理。结果表明：失活钙基吸收剂首先吸收环境中水分生成Ca(OH)₂,当吸水率达到100%后继续吸水生成Ca(OH)₂?2H₂O,自活化极限为170%;自活化可以提高失活钙基吸收剂循环碳酸化转化率,自活化后钙基吸收剂循环捕集CO₂性能与吸水率呈线性比例关系,重复自活化可再次提高吸收剂循环碳酸化转化率;自活化过程中,失活钙基吸收剂颗粒表面重新生成孔隙,比孔容和比表面积增加,有利于吸收剂中CO₂的扩散,因此自活化后钙基吸收剂循环捕集CO₂性能提高。     

高温下改性钙基吸附剂固定床反应器从烟气中捕捉二氧化碳(英文)

Four kinds of Ca-based sorbents were prepared by calcination and hydration reactions using different precursors: calcium hydroxide, calcium carbonate, calcium acetate monohydrate and calcium oxide. The CO2 absorption capacity of those sorbents was investigated in a fixed-bed reactor in the temperature range of 350-650℃. It was found that all of those sorbents showed higher capacity for CO2 absorption when the operating temperature higher than 450℃. The CaAc2-CaO sorbent showed the highest CO2 absorption capacity of 299mg·g-1. The morphology of those sorbents was examined by scanning electron microscope (SEM), and the changes of composition before and after carbonation were also determined by X-ray diffraction (XRD). Results indicated that those sorbents have the similar chemical compositions and crystalline phases before carbonation reaction [mainly Ca(OH)2], and CaCO3 is the main component after carbonation reaction. The SEM morphology shows clearly that the sorbent pores were filled with reaction products after carbonation reaction, and became much denser than before. The N2 adsorption-desorption isotherms indicated that the CaAc2-CaO and CaCO3-CaO sorbents have higher specific surface area, larger pore volume and appropriate pore size distribution than that of CaO-CaO and Ca(OH)2-CaO.     

Cl含量对钙基吸收剂微观结构以及动力学性能的影响

通过浸渍法向分析纯CaCO₃中添加Cl,在双固定床反应器系统和热重分析仪上研究了其对钙基吸收剂循环捕集CO₂性能的影响,利用离子反应模型对添加Cl后吸收剂化学反应控制阶段进行动力学分析。结果显示：Cl对钙基吸收剂循环捕集CO₂性能具有不利影响。当Cl/Ca摩尔比大于0.25%后,随Cl/Ca摩尔比增加,化学反应控制阶段反应速率和持续时间均减小,导致在该阶段最终碳酸化转化率降低。对添加Cl前后吸收剂孔隙分布特性进行分析发现,添加Cl导致煅烧后吸收剂烧结加剧,比表面积降低,10~120nm范围内孔分布减少,导致CO₂在吸收剂内部扩散阻力增加,同时能与CO₂反应的CaO量减少,这是导致吸收剂化学反应控制阶段碳酸化反应速度较慢、最终碳酸化转化率较低的主要原因。鉴于Cl的不利影响,在选择钙基材料作为CO₂吸收剂或合成高活性复合吸收剂时,应避免吸收剂中Cl含量过高。     

镁负载CaO基吸附剂捕集CO2性能及抗烧结机理

复合钙基吸附剂制备成本过高是限制其工业化应用的主要瓶颈问题。本文以不可溶的CaCO₃和Ca(OH)₂作为钙源,通过燃烧合成法制备钙镁复合吸附剂,在双固定床反应器上研究了其循环捕集CO₂性能。结果显示：制备得到的钙镁复合吸附剂具有更发达的孔隙结构,吸附剂表面Ca和Mg分散均匀,MgO均匀分布于CaO晶粒之间,有效提高了钙镁复合吸附剂的抗烧结特性,因此钙镁复合吸附剂循环反应过程中具有高捕集CO₂活性。以Ca(OH)₂作为钙源时,燃烧合成过程中Ca和Mg均匀同时析出,分散更加均匀,有效避免了CaCO₃作为钙源时Mg的团聚问题,因此得到的钙镁复合吸附剂循环捕集CO₂性能最优。最佳的Ca/Mg摩尔比为(8∶2)~(7.5∶2.5)。本研究以不可溶钙源制备得到高活性钙镁复合吸附剂,有效控制了吸附剂成本,具有更好的工程应用前景。     

不同钙基吸附剂捕集CO2后的硫酸化反应特性研究

钙基吸附剂进行多次CO₂捕集后,碳酸化效率会大幅衰减,此时的吸附剂能否高效脱硫利用是值得重点关注的问题。鉴于此,筛选了高性能合成钙基吸附剂和天然石灰石吸附剂,通过热重分析仪分析对比其在多循环CO₂捕集后的碳酸化和硫酸化反应性能,采用微粒模型研究其硫酸化反应动力学特征。结果发现,高性能合成钙基吸附剂的碳酸化反应速率和CO₂吸附能力明显高于石灰石吸附剂。在长达500循环的CO₂捕集试验后,高性能合成钙基吸附剂的CO₂吸附能力比石灰石高10倍以上,其SO₂吸附能力相较于石灰石提升约40%。经历多次CO₂捕集反应循环后,2种吸附剂的硫酸化能力均有提升:其中,石灰石吸附剂的提升幅度更大,硫酸化转化率从26%提升到35%,而高性能合成钙基吸附剂的硫酸化转化率则从38%提升到43%。通过微粒模型计算发现,2种吸附剂的硫酸化反应均是与SO₂浓度相关的一级反应,多循环捕集CO₂反应后,石灰石吸附剂的硫酸化反应活化能下降接近30%,而高性能合成钙基吸附剂的硫酸化反应活化能只下降了5%。研究结果说明2种不同钙基吸附剂在进行循环CO₂捕集后,脱硫能力得到了不同程度的提高,且均可以较好地应用于SO₂的脱除。     

钙基碳载体造粒的捕集CO特性及力学性能

采用挤出滚圆法对钙基碳载体Ca（OH）₂进行造粒。在双固定床反应器上研究了黏结剂、支撑体和造孔剂对造粒后钙基碳载体循环捕集CO₂性能的影响,并提出采用多孔Al₂O₃球粉作为新型支撑体。结果表明,选择聚乙烯吡咯烷酮为颗粒黏结剂时最佳添加量为2%。高铝水泥和多孔Al₂O₃球粉均可作为支撑体造粒。多孔Al₂O₃球粉作为支撑体造粒后碳载体的循环捕集CO₂性能更高,其10次循环后CO₂吸收量为0.23g/g,是添加高铝水泥造粒碳载体的1.35倍。微晶纤维素作为造孔剂显著提高了造粒碳载体的循环捕集CO₂性能。多孔Al₂O₃球粉作为支撑体造粒后碳载体的抗压强度略高于高铝水泥作为支撑体。多孔Al₂O₃球粉造粒钙基碳载体拥有大量30~100nm孔隙,其比孔容高于高铝水泥造粒碳载体,这有利于CO₂捕集。     

A stepwise process for carbon dioxide sequestration using magnesium silicates

This work involves the production of magnesium in the form of Mg(OH)₂ from serpentinite rock (nickel mine tailing) material followed by conversion into MgCO₃ using a pressurised fluidised bed (PFB) reactor operating at 400°C–600°C and pressures up to 2.85MPa. Our approach is rooted in the thermodynamic fact that the reaction between Mg(OH)₂ and gaseous CO₂ forming MgCO₃ and water releases significant amounts of heat. The main problem is, however, the chemical kinetics; the reaction is slow and has to be accelerated in order to be used in an economically viable process for large-scale (~1Mt/a) CO₂ sequestration. We have constructed a lab-scale PFB reactor test-setup for optimising the carbonation reaction. At high enough temperatures and conversion levels the reaction should provide the heat for the proceeding Mg(OH)₂ production step, making the overall process energy neutral. So far we have been able to achieve a conversion degree of 26% at 500°C and 2.85MPa after 30min (particle size 125–212μm). In this paper the test facility and our latest results and progress on CO₂ mineral carbonation are summarised. Also, the possible integration of the iron as a feedstock for iron and steel production will be briefly addressed. An interesting side-effect of this carbon dioxide capture and storage (CCS) route is that significant amounts of iron are obtained from the serpentinite rock material. This is released during the Mg(OH)₂ production and can be of great interest to the iron- and steel producing sector, which at the same time is Finland’s largest CO₂ producer.     

Preparation and Application of the Sol-Gel Combustion Synthesis-Made CaO/CaZrO3 Sorbent for Cyclic CO2 Capture Through the Severe Calcination Condition

abstract Calcium looping method has been considered as one of the efficient options to capture CO2 in the combustion flue gas. CaO-based sorbent is the basis for application of calcium looping and shou...     

废弃蛋壳源高性能钙基吸收剂的制备及其碳捕集性能

基于食品工业废弃蛋壳,本文利用不同有机酸反应制取乙酸钙、柠檬酸钙及葡萄糖酸钙共三种蛋壳源有机钙。在高温固定床反应器及热重分析仪上研究了不同前体所制成钙基吸收剂的碳循环捕集性能及碳酸化特性。进一步通过XRD分析了不同钙基吸收剂的物相组成,通过N₂吸附仪及SEM分析了循环前后钙基吸收剂结构特性及微观形貌的变化。结果表明,在三种蛋壳源有机钙中,葡萄糖酸钙所制成的钙基吸收剂具有较高的反应活性和相对最佳的碳捕集性能,首次碳酸化转化率高达85.33%,其钙基吸收剂相比其他吸收剂晶粒更小,20~100nm孔径范围内的孔隙较为发达,具有相对较强的抗烧结能力。经过20次循环实验发现,随着循环次数的增加,几种钙基吸收剂小颗粒均团聚烧结成大颗粒,造成孔隙结构缺失,孔隙率降低,影响其后续碳捕集性能。     

胺基CO2固体吸附剂脱碳特性及SO2的影响

燃煤电厂烟气中存在的微量SO₂对胺基CO₂固体吸附剂的碳酸化反应及循环特性有不利影响。利用固定床反应器,针对采用溶胶凝胶法制备的胺基CO₂固体吸附剂的碳酸化特性及其在含SO₂气氛下的失效规律进行了实验研究,并结合红外光谱、有机元素分析、BET等测试手段,研究其失效机理。结果表明,所制备的胺基CO₂固体吸附剂在反应温度50℃时具有较好的碳酸化反应特性和循环特性。当反应气氛中存在SO₂时,由于生成了不可再生的亚硫酸/硫酸盐类物质而导致胺基活性位损失,孔隙结构发生变化,影响了吸附剂的脱碳性能,但适当提高反应温度可提高吸附剂的碳酸化反应竞争性。     

The maximum capture efficiency of CO2 using a carbonation/calcination cycle of CaO/CaCO3

The use of natural calcium carbonates as regenerable CO₂ sorbents in industrial processes is limited by the rapid decay of the carbonation conversion with the number of cycles carbonation/calcination. However, new processes are emerging to capture CO₂ using these cycles, that can take advantage of the intrinsic benefits of high temperature separations in energy systems. This work presents an analysis of a general carbonation/calcination cycle to capture CO₂, incorporating a fresh feed of sorbent to compensate for the decay in activity during sorbent re-cycling. A general design equation for the maximum CO₂ capture efficiency is obtained by incorporating to the cycle mass balances a simple but realistic equation to estimate the decay in sorbent activity with the number of cycles.     

钙循环捕集CO2后CaO的水合/脱水热化学储热性能

提出了基于CaO的钙循环捕集CO₂与CaO/Ca(OH)₂体系热化学储热耦合新工艺，在双固定床反应器上，研究了循环捕集CO₂中煅烧条件和碳酸化条件对CaO储热性能的影响，探究CaO循环捕集CO₂过程和循环水合/脱水储热过程的相互作用。研究表明，多次循环碳酸化/煅烧捕集CO₂后CaO仍具有较高储热性能，10次循环捕集CO₂后再经10次储热循环，CaO水合转化率可达0.66mol/mol。与苛刻煅烧条件相比，温和煅烧条件下经历多次循环捕集CO₂后CaO的储热性能更高。在碳酸化气氛中加入水蒸气对经历多次循环捕集CO₂后CaO储热性能的影响不大。钙循环捕集CO₂过程和水合/脱水循环储热过程能够相互促进。该工艺有望同时实现CO₂捕集和储热，具有一定的应用前景。     

鼓泡床中电石渣加速碳酸化分析与响应面优化

搭建了鼓泡床碳酸化反应器,研究常温常压下电石渣直接液相碳酸化矿化封存CO₂的能力,揭示了重要操作参数表观气速、液固比和CO₂浓度对电石渣矿化封存CO₂能力和碳酸化效率的影响规律。同时构建响应面模型,分析各参数对电石渣碳酸化效率的影响强度,优化获得最大碳酸化效率及相应操作工况。结果表明,增加气速有利于钙离子溶解和CO₂吸收,但反应器中过高气速易导致气相通道效应,不利于气液充分接触。当液固比降低,溶液中钙离子浓度提高,更有利于碳酸化反应,但液固比过低会影响固液间传质。适当增加CO₂浓度有利于提高碳酸化效率,但CO₂浓度增至到一定值后,对碳酸化效率影响降低。响应面建模分析发现,各因素对碳酸化效率影响顺序为：液固比>CO₂浓度>表观气速。优化结果发现碳酸化效率最高为93.58%,工况为表观气速0.07m/s,液固比为8.26mL/g和CO₂体积分数为20.91%。研究可知,鼓泡床中常温常压下电石渣直接液相加速碳酸化反应,具有较大的CO₂固定量和高的碳酸化效率,实验结果为电石渣加速矿化封存CO₂技术的发展提供了基础数据。     

TiO2掺杂对Na2CO3/Al2O3吸收剂CO2捕捉性能的影响

钠基固体吸收剂脱除燃煤烟气CO₂技术具有反应温度低、能耗低等优点,日益受到学术界的关注。该技术的主要不足是吸收剂的活性成分碳酸钠与CO₂的反应（碳酸化反应）活性较低。针对这一问题,本文旨在研制一种新型改性钠基固体吸收剂,采用活性氧化铝作为载体、TiO₂作为掺杂剂进行改性,利用热重分析装置、XRD、SEM和氮吸附仪研究钠基固体吸收剂的CO₂捕捉性能。结果表明：掺杂TiO₂后,钠基固体吸收剂与CO₂的反应速率加快,CO₂捕捉量增加;反应前后除TiO₂外无其他含Ti化合物生成;碳酸化反应产物为NaHCO₃和Na₅H₃（CO₃）₄;然而TiO₂掺杂过多会堵塞吸收剂的微观孔道,不利于甚至阻碍碳酸化反应的进行,因此,TiO₂的掺杂量应控制在一定的范围内。     

间歇氯化对电石渣循环捕集CO2性能的影响

提出在碳酸化气氛中间歇加入HCl（间歇氯化）提高电石渣在循环煅烧/碳酸化反应中捕集CO₂性能的新思路。在双固定床反应器上,在不同循环次数加入HCl、碳酸化温度、CO₂/HCl体积比等条件下,研究HCl间歇加入对电石渣循环碳酸化特性的影响。结果表明,在循环煅烧/碳酸化反应中间歇加入HCl使电石渣间歇氯化能提高其循环捕集CO₂性能。在前N次循环碳酸化时加入0.1% HCl,当N=4时能使电石渣获得最优CO₂捕集性能,第10个循环时的CO₂吸收量比无HCl时提高了51%。HCl与CaCO₃发生氯化反应,破坏致密产物层对CO₂扩散的阻碍,提高了电石渣的碳酸化转化率。在碳酸化气氛加入HCl时,最佳碳酸化温度仍为700℃。随CO₂/HCl体积比增大,HCl对电石渣捕集CO₂性能的促进作用减弱。     

Na2CO3基吸附剂颗粒制备及其脱碳性能

采用挤压-滚圆法制备Na₂CO₃基CO₂吸附剂微球颗粒,在自行设计的CO₂吸收系统中对制备的样品进行脱碳性能测试。结合相关表征测试,探明不同载体、不同负载量的Na₂CO₃基吸附剂的微观结构、脱碳性能以及机械性能的变化规律和内在原因。研究表明：不同载体的Na₂CO₃基吸附剂颗粒脱碳性能存在明显差异,其中氧化铝负载的吸附剂（Na₂CO₃/Al₂O₃）的脱碳性能最好,可达1.14mmol/g。铝酸钙水泥负载的吸附剂（Na₂CO₃/CA）机械性能较好,但其脱碳性能最差。结合吸附剂脱碳和机械性能的综合考量,Na₂CO₃/Al₂O₃是最为合适的CO₂吸附剂,并进一步研究不同Na₂CO₃负载量的影响。研究发现随着Na₂CO₃负载量的变化,吸附剂的微观结构、脱碳性能以及机械性能都存在明显的差异。虽然60%负载量的Na₂CO₃/Al₂O₃吸附剂颗粒的机械性能和脱碳效果较好,但其成球度较差,影响其实际应用。质量分数40%负载量的Na₂CO₃/Al₂O₃吸附剂颗粒具有良好的脱碳性能、机械性能以及成球度,CO₂脱除量为1.36mmol/g。总体而言,利用挤压-滚圆法制备的Na₂CO₃基吸附剂颗粒具有良好的流动特性、脱碳性能和机械性能,适用于电厂烟气中的CO₂脱除。     

Parametric study and effect of calcination and carbonation conditions on the CO2 capture performance of lithium orthosilicate sorbent

The world is currently facing the challenges of global warming and climate change. Numerous efforts have been taken to mitigate CO_2 emission, among which is the use of solid sorbents for CO_2 capture. In this work, Li_4SiO_4 was synthesised via a sol–gel method using lithium nitrate(LiNO_3) and tetraethylorthosilicate(Si C8 H20 O4) as precursors. A parametric study of Li:Si molar ratio(1-5), calcination temperature(600–800 °C) and calcination time(1–8 h) were conducted during sorbent synthesis. Calcination temperature(700–800 °C) and carbonation temperature(500–700 °C) during CO_2 sorption activity were also varied to confirm the optimum operating temperature. Sorbent with the highest CO_2 sorption capacity was finally introduced to several cyclic tests to study the durability of the sorbent through 10 cycles of CO_2 sorption–desorption test. The results showed that the calcination temperature of 800 °C and carbonation temperature of 700 °C were the best operating temperatures, with CO_2 sorption capacity of 7.95 mmol CO_2?(g sorbent)-1(93% of the theoretical yield). Throughout the ten cyclic processes, CO_2 sorption capacity of the sorbent had dropped approximately 16.2% from the first to the tenth cycle, which was a reasonable decline. Thus, it was concluded that Li_4SiO_4 is a potential CO_2 solid sorbent for high temperature CO_2 capture activity.     

循环捕集CO2后煅烧石灰石的硫化特性

ZEC(zero emission coal)系统中,粗煤气进入碳酸化/重整炉前需先脱除H₂S,提出利用经过多次碳酸化/煅烧捕集CO₂循环的煅烧石灰石(CaO)脱除H₂S,并研究循环碳酸化/煅烧次数、硫化温度、H₂S浓度和微观结构对循环CaO硫化特性的影响。结果表明,多次循环碳酸化/煅烧捕集CO₂后CaO仍具有较高H₂S吸收性能。前20次循环,CaO硫化转化率随循环次数增加迅速降低;20次循环后,CaO硫化转化率缓慢下降。硫化120 min后,未循环CaO的硫化转化率接近100%,而经历1、20和100次循环后CaO的硫化转化率分别为94%、81%和74%。H₂S浓度对循环CaO硫化性能影响较大。硫化温度(800～1000℃)对循环CaO的硫化性能影响较小,最佳硫化温度为900℃。随循环次数增加,CaO颗粒发生高温烧结,导致比表面积降低和20～150 nm内孔隙减少,而这是与H₂S吸收密切相关的孔隙,导致CaO硫化转化率降低。     

CO2 absorption and regeneration of alkali metal-based solid sorbents

Potassium-based sorbents were prepared by impregnation with potassium carbonate on supports such as activated carbon (AC), TiO₂, Al₂O₃, MgO, SiO₂ and various zeolites. The CO₂ capture capacity and regeneration property were measured in the presence of H₂O in a fixed-bed reactor, during multiple cycles at various temperature conditions (CO₂ capture at 60 °C and regeneration at 130–400 °C). Sorbents such as K₂CO₃/AC, K₂CO₃/TiO₂, K₂CO₃/MgO, and K₂CO₃/Al₂O₃, which showed excellent CO₂ capture capacity, could be completely regenerated above 130, 130, 350, and 400 °C, respectively. The decrease in the CO₂ capture capacity of K₂CO₃/Al₂O₃ and K₂CO₃/MgO, after regeneration at temperatures of less than 200 °C, could be explained through the formation of KAl(CO₃)₂(OH)₂, K₂Mg(CO₃)₂, and K₂Mg(CO₃)₂·4(H₂O), which did not completely converted to the original K₂CO₃ phase. In the case of K₂CO₃/AC and K₂CO₃/TiO₂, a KHCO₃ crystal structure was formed during CO₂ absorption, unlike K₂CO₃/Al₂O₃ and K₂CO₃/MgO. This phase could be easily converted into the original phase during regeneration, even at a low temperature (130 °C). Therefore, the formation of the KHCO₃ crystal structure after CO₂ absorption is an important factor for regeneration, even at the low temperature. The nature of support plays an important role for CO₂ absorption and regeneration capacities. In particular, the K₂CO₃/TiO₂ sorbent showed excellent characteristics in CO₂ absorption and regeneration in that it satisfies the requirements of a large amount of CO₂ absorption (mg CO₂/g sorbent) and fast and complete regeneration at a low temperature condition (1 atm, 150 °C).     

ULTRASONICATION-ASSISTED SYNTHESIS OF CALCIUM CARBONATE NANOPARTICLES

This article presents a batch carbonation method with ultrasonication to synthesize monodispersed nanoparticles of calcium carbonate (CaCO₃). The synthesis processes with and without ultrasonication were compared. The results showed that the application of ultrasonication into the synthesis caused a supersaturation of Ca²⁺ ions in the synthesis, leading to a rapid nucleation of calcium carbonate and improved the solute transfer as well as. It was also found that the effect of ultrasonication on the grain size of the nanoparticles synthesized was related to other synthesis conditions, such as initial temperature for carbonation, mass fraction of Ca(OH)₂ suspension, and CO₂ flow rate. The initial temperature applied for the carbonation was increased by at least 5°C when ultrasonication was applied. The nanoparticles formed in the presence of ultrasonication became smaller with a narrower particle size distribution at 6-12 wt.% of Ca(OH)₂ suspension or at 1.28 l/h of CO₂ consumed by per gram of Ca(OH)₂ or more.