Synthesis and electrochemiluminescence of the CeO2/TiO2 composite

CeO₂/TiO₂ composite with kernel–shell structure was synthesized by a sol–gel process. The characterization results show that the composite is made up of anatase phase TiO₂ and cubic system CeO₂. The electrochemiluminescence (ECL) behavior of the CeO₂/TiO₂ composite was studied by a cyclic voltammetry in the presence of persulfate, and the effect factors on ECL emission were discussed. Based on a series of experiments, it is proposed that the strong dual ECL emission produced by the CeO₂/TiO₂ composite resulted from the benefit ECL effect of interface heterojunction in composite.     

Preparation and characterization of CeO2/TiO2 nanoparticles by flame spray pyrolysis

Nanocrystalline TiO₂, CeO₂ and CeO₂-doped TiO₂ have been successfully prepared by one-step flame spray pyrolysis (FSP). Resulting powders were characterized with X-ray diffraction (XRD), N₂-physisorption, Transmission Electron Microscopy (TEM) and UV-Vis spectrophotometry. The TiO₂ and CeO₂-doped TiO₂ nanopowders were composed of single-crystalline spherical particles with as-prepared primary particle size of 10-13 nm for Ce doping concentrations of 5-50 at%, while square-shape particles with average size around 9 nm were only observed from flame-made CeO₂. The adsorption edge of resulting powder was shifted from 388 to 467 nm as the Ce content increased from 0 to 30 at% and there was an optimal Ce content in association with the maximum absorbance. This effect is due to the insertion of Ce^3+/4+ in the TiO₂ matrix, which generated an n-type impurity band.     

CO hydrogenation to iso-C4 hydrocarbons over CeO2–TiO2 catalysts

CeO₂–TiO₂ (Ce:Ti = 0.25–9, molar ratio) catalysts were synthesized by a sol–gel method and the catalytic performances were evaluated in the selective synthesis of isobutene and isobutane from CO hydrogenation under the reaction conditions of 673–748 K, 1–5 MPa and 720–3000 h⁻¹. The physical properties, such as specific surface area, cumulative pore volume, average pore diameter, crystal phase and size, of the catalysts were characterized by N₂ adsorption/desorption and XRD. All the CeO₂–TiO₂ composite oxides showed higher surface areas than pure TiO₂ and CeO₂. No TiO₂ phase was detected on the samples of CeO₂–TiO₂ in which TiO₂ contents were in the range of 10–50 mol%. Crystalline Ce₂O₃ was detected in CeO₂–TiO₂ (8:2). The reaction conditions, temperature, pressure and space velocity, had obvious influences on the CO conversion and distribution of the products over CeO₂–TiO₂ (8:2) catalyst.     

Synthesis and electrochemical properties of CeO2 nanoparticle modified TiO2 nanotube arrays

In this paper, a cerium dioxide (CeO₂) modified titanium dioxide (TiO₂) nanotube array film was fabricated by electrodeposition of CeO₂ nanoparticles onto an anodized TiO₂ nanotube array. The structural investigation by X-ray diffraction, scanning electron microscopy and transmission electron microscopy indicated that the CeO₂ nanoparticles grew uniformly on the walls of the TiO₂ nanotubes. The composite was composed of cubic-phase CeO₂ crystallites and anatase-phase TiO₂ after annealing at 450 °C. The cyclic voltammetry and chronoamperometric charge/discharge measurement results indicated that the CeO₂ modification obviously increased the charge storage capacity of the TiO₂ nanotubes. The charge transfer process at the surface, that is, the pseudocapacitance, was the dominate mechanism of the charge storage in CeO₂-modified TiO₂ nanotubes. The greater number of surface active sites resulting from uniform application of the CeO₂ nanoparticles to the well-aligned TiO₂ nanotubes contributed to the enhancement of the charge storage density.     

TiO2, TiO2/Ag and TiO2/Au photocatalysts prepared by spray pyrolysis

TiO₂, TiO₂/Ag and TiO₂/Au photocatalysts exhibiting a hollow spherical morphology were prepared by spray pyrolysis of aqueous solutions of titanium citrate complex and titanium oxalate precursors in one-step. Effects of precursor concentration and spray pyrolysis temperature were investigated. By subsequent heat treatment, photocatalysts with phase compositions from 10 to 100% rutile and crystallite sizes from 12 to 120 nm were obtained. A correlation between precursor concentration and size of the hollow spherical agglomerates obtained during spray pyrolysis was established. The anatase to rutile transformation was enhanced with metal incorporations and increased precursor concentration. The photocatalytic activity was evaluated by oxidation of methylene blue under UV-irradiation. As-prepared TiO₂ particles with large amounts of amorphous phase and organic residuals showed similar photocatalytic activity as the commercial Degussa P25. The metal incorporated samples showed comparable photocatalytic activity to the pure TiO₂ photocatalysts.     

Catalytic combustion of chlorobenzene over MnOx–CeO2 mixed oxide catalysts

A series of MnOx–CeO₂ mixed oxide catalysts with different compositions prepared by sol–gel method were tested for the catalytic combustion of chlorobenzene (CB), as a model of volatile organic compounds of chlorinated aromatics. MnOx–CeO₂ catalysts with different ratios of Mn/Ce + Mn were found to possess high catalytic activity in the catalytic combustion of CB, and MnOx(0.86)–CeO₂ was identified as the most active catalyst, on which the temperature of complete combustion of CB was 254 °C. Effects of systematic variation of reaction conditions, including space velocity and inlet CB concentration on the catalytic combustion of CB were investigated. Additionally, the stability and deactivation of MnOx–CeO₂ catalysts were studied by various characterization methods and other assistant experiments. MnOx–CeO₂ catalysts with high Mn/Ce + Mn ratios present a stable high activity, which is related to their high ability to remove the adsorbed Cl species and a large amount of active surface oxygen.     

Effect of Zr-ion substitution in CeO2 on H2O2-assisted degradation of orange G

A series of Pd ion-substituted CeO₂–ZrO₂ solid solutions were synthesized using the solution combustion technique. H₂O₂-assisted degradation of orange G was carried out in the presence of the catalysts. The activity of the catalysts was found to increase with the introduction of the second component in the solid solution, as signified by an increase in the rate constants and lowering of activation energy. The study showed the involvement of lattice oxygen and the importance of reducibility of the compound for the reaction.     

Effect of TiO2 particle size on the photocatalytic reduction of CO2

Pure TiO₂ anatase particles with a crystallite diameters ranging from 4.5 to 29 nm were prepared by precipitation and sol–gel method, characterized by X-ray diffraction (XRD), BET surface area measurement, UV–vis and scanning electron microscopy (SEM) and tested in CO₂ photocatalytic reduction. Methane and methanol were the main reduction products. The optimum particle size corresponding to the highest yields of both products was 14 nm. The observed optimum particle size is a result of competing effects of specific surface area, charge–carrier dynamics and light absorption efficiency.     

Oriented polycrystalline mesoporous CeO2 with enhanced pore integrity

Mesoporous CeO₂ particles are synthesized using a sol–gel method involving Pluronic P123 or F127 tri-block copolymer and cerium acetate hydrate. Transmission electron microscopy reveals well defined meso-channels of about 10 nm in diameter and a wall framework consisting of highly oriented polycrystalline CeO₂. The [0 0 1] axis of the crystals is found to be aligned parallel to the meso-channels, and lattice coherency of [1 0 0] or [0 1 0] also exists in perpendicular plane to the channel. A cooperative self-assembly of the tri-block copolymer and Ce⁴⁺ species is believed to occur, along with the precipitation of nano-crystalline CeO₂ in the sol–gel process. It is proposed that the preferential orientation may result from a favored linkage of the low-order Miller indices {0 0 1} planes of CeO₂ to the PEO segment in the PEO–PPO–PEO tri-block copolymer micelles. The unique structural characteristics of meso-CeO₂ appear to contribute to maintaining the pore integrity during the synthesis as well as in a post-fabrication in situ TEM heating test.     

Enhancement of oxygen storage capacity by reductive treatment of Al2O3 and CeO2–ZrO2 solid solution nanocomposite

Oxygen storage capacity (OSC) of CeO₂–ZrO₂ solid solution, Ce_xZr_(1−x)O₄, is one of the most contributing factors to control the performance of an automotive catalyst. To improve the OSC, heat treatments were employed on a nanoscaled composite of Al₂O₃ and CeZrO₄ (ACZ). Reductive treatments from 700 to 1000 °C significantly improved the complete oxygen storage capacity (OSC-c) of ACZ. In particular, the OSC-c measured at 300 °C reached the theoretical maximum with a sufficient specific surface area (SSA) (35 m²/g) after reductive treatment at 1000 °C. The introduced Al₂O₃ facilitated the regular rearrangement of Ce and Zr ions in CeZrO₄ as well as helped in maintaining the sufficient SSA. Reductive treatments also enhanced the oxygen release rate (OSC-r); however, the OSC-r variation against the evaluation temperature and the reduction temperature differed from that of OSC-c. OSC-r measured below 200 °C reached its maximum against the reduction temperature at 800 °C, while those evaluated at 300 °C increased with the reduction temperature in the same manner as OSC-c.     

Aerobic oxidation of alcohols over Au/TiO2: An insight on the promotion effect of water on the catalytic activity of Au/TiO2

The unique and significant promotion effect of water has been evidenced by the selective oxidation of benzyl alcohol to benzaldehyde over Au/TiO₂ catalysts. Water has dual promotional functions in the reaction system: to help form unique microdroplets in a multiphase reaction system and to assist the oxygen adsorption and activation. The conversion of benzyl alcohol at a molar ratio of water to solvent (p-xylene) of 7 is 7 times higher than in the absence of water. The present work has highlighted the potential of Au/TiO₂ catalysts in aerobic oxidation of alcohols in the unique multiphase reaction system with water as promoting solvent.     

Effect of Ag addition on the properties of Pd–Ag/TiO2 catalysts containing different TiO2 crystalline phases

Anatase and rutile TiO₂ were used for preparation of the TiO₂ supported Pd and Pd–Ag catalysts for selective hydrogenation of acetylene. It was found that Pd/TiO₂-anatase exhibited higher acetylene conversion and ethylene selectivity than rutile TiO₂ supported ones. However, addition of Ag to Pd/TiO₂-anatase catalyst resulted in lower ethylene selectivity while that of Pd/TiO₂-rutile increased. It is suggested that Ag addition suppressed the beneficial effect of the Ti³⁺ sites presented on the anatase TiO₂ during selective acetylene hydrogenation whereas without Ti³⁺, Ag promoted ethylene selectivity by blocking sites for over-hydrogenation of ethylene to ethane.     

基于WO3-MoO3和TiO2/CdS复合电极的光电致变色器件

电致变色广泛应用于智能窗领域,但电致变色材料仍需外部电源驱动,将太阳能电池与电致变色材料结合起来的光电致变色器件可实现无需外部供电的智能变色调控。性能优异的变色阴极和光阳极是当下光电致变色器件的研究热点。通过水热法制备WO₃-MoO₃薄膜,研究其电致变色性能;通过水热法结合连续离子层沉积法制备TiO₂/CdS复合薄膜,研究其光电转换性能。最后将WO₃-MoO₃薄膜和TiO₂/CdS复合薄膜分别作为光电致变色器件的变色阴极、光阳极构建WO₃/MoO₃-TiO₂/CdS光电致变色器件。WO₃/MoO₃-TiO₂/CdS光电致变色器件具有较大的光学调制范围(630nm处为41.99%)、更高的着色效率(35.787%),将其作为智能窗应用在现代建筑、通行工具等领域具有重要应用价值。     

Enhanced electrochemical and thermal stability of surface-modified LiCoO2 cathode by CeO2 coating

CeO₂-coated LiCoO₂ particles were successfully synthesized by a sol-gel coating of CeO₂ on the surface of the LiCoO₂ powder and subsequent heat treatment at 700 °C for 5 h. The surface-modified and pristine LiCoO₂ powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Auger electron spectroscopy (AES), slow rate cyclic voltammogram (CV), and differential scanning calorimetry (DSC). Cyclic voltammetry curves suggested that the CeO₂ coating suppressed the phase transitions. Unlike pristine LiCoO₂, the CeO₂-coated LiCoO₂ cathode exhibited better capacity retention than the pristine LiCoO₂ electrode in the higher cutoff voltage. Differential scanning calorimetric data revealed the higher thermal stability of the CeO₂-coated LiCoO₂ electrode.     

Effect of TiO2 on phase evolution and microstructure of MgAl2O4 spinel in different atmospheres

The effect of TiO₂ on the formation and microstructure of magnesium aluminate spinel (MgAl₂O₄) at 1600 °C in air and reducing conditions were investigated. Under reducing conditions, stoichiometric MgAl₂O₄ spinel shifted toward alumina-rich types owing to volatilization of MgO, resulting in an increase in the porosity of fired samples. Addition of graphite to mixtures of MgO and Al₂O₃ intensified the reducing conditions and accelerated the formation of non-stoichiometric MgAl₂O₄. For TiO₂-containing samples on addition of MgAl₂O₄, magnesium aluminum titanium oxide (Mg_xAl_2(1−x)Ti_(1+x)O₅, x = 0.2 or 0.3) was detected as a minor phase. Under reducing conditions, XRD peak shifts were smaller for TiO₂-containing samples than for samples without TiO₂ owing to the formation of a solid solution of TiO₂ in MgAl₂O₄ and establishment of alumina-rich spinel, which have opposite effects on increasing the lattice parameter. In bauxite-containing samples, MgAl₂O₄ spinel, corundum, magnesium orthotitanate spinel (Mg₂TiO₄) and amorphous phases were identified. Mg₂TiO₄ spinel formed a complete solid solution with MgAl₂O₄ spinel but Mg₂TiO₄ remained as a distinct phase owing to the heterogeneous microstructure of bauxite-containing samples. Also dense microstructure established in air fired TiO₂ containing samples. The results are discussed with emphasis on the application and design of alumina-magnesia-carbon refractory materials, which are used in the steel industry.     

Synthesis of CeO2-ZrO2 solid solution by glycothermal method and its oxygen release capacity

The glycothermal (GT) reaction of Ce acetate and Zr alkoxide directly yielded CeO₂-ZrO₂ solid solutions in a region of low Ce content ≤40 mol%. Of the CeO₂-ZrO₂ solid solutions obtained by the GT method and subsequent calcination at 500 or 800 °C, the sample with 20 mol% Ce content had the largest BET surface area. This sample exhibited the highest Ce-based oxygen release capacity in the whole Ce/Zr composition range. The oxygen release capacities of CeO₂-ZrO₂ solid solutions synthesized by the GT method were much larger than those of the samples prepared by a coprecipitation (CP) method. The Reitveld analysis and the repetitive reduction-oxidation experiment indicated that the CeO₂-ZrO₂ solid solution synthesized by the GT method has a homogeneous structure as compared with that prepared by the CP method.     

Chemical reduction of nanocrystalline CeO2

The reduction of commercial and mechanochemically processed CeO₂ powders was studied. Nanostructured CeO₂, with the crystallite size of 21 nm and the lattice distortion of 0.37%, was obtained during 60 min of milling in a high-energetic vibratory mill. X-ray diffraction, scanning electron microscopy and Brunauer-Emmett-Teller method were applied to characterize the milled powders. During the thermal treatment at 1200 and 1400 °C in an argon atmosphere the nonstoichiometric CeO_2−x oxides with the defect fluorite structure were formed. Compositions of CeO_2−x oxides were determined according to its lattice parameter. The results showed that the release of oxygen, as well as the rate of reduction, was more effective in nanocrystalline then in the microcrystalline CeO₂, producing at 1200 °C CeO_1.80 and CeO_1.85 oxides, while at 1400 °C were obtained similarly, CeO_1.77 and CeO_1.78, compositions.     

TiO2 nanotubes and CNT–TiO2 hybrid materials for the photocatalytic oxidation of propene at low concentration

In this work, we investigated titanium dioxide (TiO₂) nanotubes and CNT–TiO₂ hybrid materials for the photocatalytic oxidation (PCO) of propene at low concentration (100 ppmv) in gaseous phase. The materials were prepared via sol–gel method using sacrificial multi-walled carbon nanotubes (CNT) as templates and subsequent heat treatments to obtain the desired crystalline phase (anatase, rutile or a mixture of both) and eventually to remove the carbon template. We also studied rutile nanotubes for the first time and demonstrate that the activity strongly depends on the crystalline composition, following rutile < anatase < anatase/rutile mixture. The enhanced activity of the anatase–rutile mixture is attributed to the decrease in the electron–hole pair recombination due to the multiphasic nature of the particles. The key result of this work is the exceptional performance of the CNT–TiO₂ hybrid, which yielded the highest observed photocatalytic activity. The improved performance is attributed to synergistic effects due to the hybrid nature of the material, resulting in small anatase crystalline sizes (CNT act as heat sinks) and a reduced electron–hole pair recombination rate (CNTs act as electron traps). These results demonstrate the great potential of hybrid materials and stimulate further research on CNT-inorganic hybrid materials in photocatalysis and related areas.