掺Fe3+A-TiO2的水热法制备及其光催化性能研究

采用水热法以硫酸钛为原料制备了掺Fe3+ TiO2粉末,并通过SEM、TEM和XRD测定了样品的形貌和晶型,研究了自制掺Fe3+TiO2对甲基橙溶液的光催化降解作用.结果表明,所制备的TiO2为锐钛矿型(即A-TiO2).254nm紫外光照射下,用自制掺Fe3+A-TiO2降解甲基橙溶液的最佳条件是:在12mg/L甲基橙溶液中加入0.050g掺5%Fe3十(摩尔分数)的A-TiO2粉末,28℃恒温反应4h,降解率达到62.52%.同样条件下不加A-TiO2时甲基橙自身光解率为16.73%,加入纯A-TiO2时甲基橙降解率为51.75%,而加入掺杂10%Fe3+的A-TiO2其降解率为59.01%.     

不同催化剂可见光催化H2O2降解莠去津的性能研究

以锐钛矿型TiO2(记为A)以及Fe3+改性后的锐钛矿型TiO2(记为Fe-A)为光催化剂,以内分泌干扰物莠去津为目标污染物,研究了H2O2加入前后对两种不同催化剂可见光催化降解莠去津的影响,及其可见光催化降解莠去津的反应机理。结果表明:在H2O2存在的条件下,锐钛矿型TiO2可见光催化降解莠去津的光催化性能有了一定的提高,而Fe3+改性过后的锐钛矿型TiO2可见光催化降解莠去津的性能却得到显著提高,反应1h,降解率便达到98%。形成这种结果的原因可以初步判定为前者是H2O2吸附于锐钛矿型TiO2表面形成特殊结构,产生的O2-.主要起氧化降解作用,而后者则由于其溶出的Fe3+与H2O2作用在可见光下发生光芬顿反应,进而对莠去津起到良好的降解效果。     

水热法合成TiO2/Fe3+光催化剂及其氧化降解亚甲基蓝

以硫酸钛为钛源,采用水热法合成了TiO2/Fe3+光催化剂,利用XRD对产物晶体结构进行表征,研究在紫外光(365nm)照射下用合成的TiO2/Fe3+粉末催化降解亚甲基蓝的效果,分析了亚甲基蓝初始浓度、TiO2/Fe3+用量、掺Fe3+量、光照时间和溶液初始pH值等因素的影响;考察了溶液初始pH值对TiO2/Fe3+粉末的吸附性能和光催化活性的影响。结果表明:合成的TiO2/Fe3+晶体为锐钛矿型(A-TiO2)。在4mg/L的亚甲基蓝溶液(pH=8)中,加入掺Fe3+量0.8%(摩尔分数)合成的TiO2/Fe3+粉末使其用量为0.6g/L,室温下紫外光照反应6h,亚甲基蓝的降解率达到98.2%。在上述优化条件下,当溶液的pH<6时,催化剂对亚甲基蓝的吸附量和光催化效率均较低,且二者随pH升高而显著增加;当pH≥6时,对亚甲基蓝的吸附作用较大,因此较明显地提高了光催化活性。     

煅烧温度、煅烧时间和Fe3+掺杂量对TiO2光催化性能的影响

以钛酸四正了酯为先驱物,采用溶胶-凝胶法制备了纯TiO2和Fe3+掺杂的纳米TiO2(Fe3+/TiO2)光催化剂,并用XRD、UV-Vis等进行了表征,系统研究了煅烧温度、煅烧时间和Fe3+掺杂量对催化剂在自然光条件下光催化降解甲基橙性能的影响.结果表明,相同煅烧温度下,Fe3+/TiO2的粒径比纯TiO2的粒径小.制备纯TiO2和Fe3+/TiO2的最佳煅烧时间分别为4h和3h,最佳煅烧温度均为773K.适量掺入Fe3+可以显著提高纳米TiO2在自然光条件下的光催化降解活性,Fe3+/TiO2中Fe3+的最佳掺杂量为10.00%,相应的脱色效率为28.37%.     

钒铁掺杂TiO_2微球的制备及其光催化性能研究

采用水热法在不使用模板剂的条件下合成了在水中分散良好、粒径为300～800nm、规则的锐钛矿型TiO2微球.用NH4VO3和FeC2O4按原子分数为0%、0.8%、1.6%、2.4%进行V5+、Fe3+掺杂;当TiO2质量浓度为0.134g/L、pH值为9时进行可见光降解20mg/L亚甲基蓝实验.结果表明,V掺杂的降解效果与P25粉接近,Fe掺杂有抑制光催化的效果,钒铁共掺杂则呈现出短期降解能力优于未掺杂微球,并且比P25粉沉淀得更彻底、更迅速.通过XRD、FTIR、SEM分析发现,TiO2微球是由粒径约为10nm的晶粒组成,V5+进入TiO2的晶格,Fe3+则以QFe2O3形式存在于微球中.     

磁性La3+掺杂TiO2的制备及性能

利用溶胶-凝胶法,在室温条件下,以钛酸四丁酯、硝酸镧为主要原料,无水乙醇为溶剂,冰醋酸为抑制剂,浓硝酸为催化剂制得稳定的掺La3+TiO2溶胶,陈化后的凝胶经不同温度煅烧3h后制得不同掺La3+量的TiO2。通过XRD对不同煅烧温度及不同掺La3+量的TiO2进行了表征;以紫外光为光源,研究了掺La3+-TiO2对甲基橙溶液的光降解效果。用化学共沉淀法制备了具有强磁性的Fe3O4水基磁流体,再与La3+掺杂TiO2进行复合,制备了Fe3O4负载量不同的磁性La3+掺杂TiO2,研究了Fe3O4负载量不同的La3+掺杂TiO2对甲基橙的光催化降解效果、磁分离回收率的影响。结果表明,掺La3+量及煅烧温度对TiO2的晶型、各晶型TiO2的相对含量及对甲基橙的光降解效果均有影响。La3+掺杂TiO2比纯TiO2显示出更强的光催化性能,掺La3+量2%,热处理温度450℃的La3+掺杂TiO2光催化活性最高。Fe3O4负载量为10%的Fe3O4/La3+-TiO2对甲基橙的降解率8h时为99.4%;磁分离回收率达97.39%。     

TiO_2-Al_2O_3负载型催化剂的制备及其光催化性能

以钛酸四丁酯和氢氧化钠为反应物,采用两步水热法制备TiO2纳米线,并将其原位负载于Al2O3载体上,研究它们对甲基橙的光催化降解性能。结果表明,锐钛矿相TiO2主要呈纳米线和八面体状负载在Al2O3载体上,当TiO2负载质量分数为30%,焙烧温度为400℃,催化剂用量为1.332 0 g/L时,TiO2-Al2O3负载型催化剂光催化降解甲基橙的性能最佳,光照5 h后,甲基橙在紫外和太阳光下的降解率分别达到58.9%和55.6%。相同实验条件下,TiO2-Al2O3负载型催化剂对甲基橙的降解率比单纯TiO2提高了35.1%。     

静电纺丝法制备Fe3+/TiO2纳米纤维及表征

以聚乙烯吡咯烷酮(PVP)为纤维模板,钛酸四丁酯(Ti[O(CH2)3CH3]4)和Fe3+为前驱体,乙醇为溶剂,醋酸为催化剂,采用静电纺丝法制备不同含铁量的复合纳米纤维Fe3+/TiO2,经500℃煅烧得到以锐钛矿为主的Fe3+/TiO2纳米纤维。采用扫描电子显微镜(SEM)和X射线衍射仪(XRD)分别表征了Fe3+/TiO2纳米纤维的形貌与晶态,计算了样品的晶粒尺寸和锐钛矿所占的比例,并比较了5%Fe3+/TiO2纳米纤维、5%Fe3+/TiO2粉体以及纯TiO2纳米纤维三者光催化降解亚甲基蓝(MB)的效果。研究表明:由静电纺丝法制备的5%Fe3+/TiO2纳米纤维的光催化降解效果比相同含铁量的粉体的降解效果好,TiO2纳米纤维比5%Fe3+/TiO2纳米纤维的光催化活性高。     

金属掺杂对纳米管TiO2光催化性能的影响

利用水热法,以DegussaP-25TiO2粉末为原料,AlCl3、Fe(NO3)3·9H2O和ZnCl2为掺杂剂合成金属掺杂纳米管TiO2,并采用透射电镜(TEM)X射线衍射(XRD)、X射线光电子能谱(XPS)和BET比表面积分析对催化剂进行表征。结果表明,掺杂金属分别以Al3+ 、Fe3+和Zn2+的形式存在。随着煅烧温度的增高,样品的比表面积逐渐降低,锐钛矿含量先增大后减小;金属掺杂后,催化剂比表面积略有降低,锐钛矿含量 略 有 增 大。考 察 紫 外 光 催 化 臭 氧 化 工 艺 中TiO2降解腐植酸标志物的催化效果,结果表明,450℃煅烧未掺杂纳米管TiO2对腐植酸的催化降解效率为44%,较P-25TiO2粉末提高了11%;金属掺杂后催化效果提升明显,550℃煅烧Fe掺杂纳米管TiO2的催化效果最为显著,腐植酸去除率达77%。     

金属掺杂对纳米管TiO2光催化性能的影响

利用水热法,以Degussa P-25TiO2粉末为原料,AlCl3、Fe(NO3)3·9H2O和ZnCl2为掺杂剂合成金属掺杂纳米管TiO2,并采用透射电镜(TEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)和BET比表面积分析对催化剂进行表征。结果表明,掺杂金属分别以Al 3+、Fe3+和Zn2+的形式存在。随着煅烧温度的增高,样品的比表面积逐渐降低,锐钛矿含量先增大后减小;金属掺杂后,催化剂比表面积略有降低,锐钛矿含量略有增大。考察紫外光催化臭氧化工艺中TiO2降解腐植酸标志物的催化效果,结果表明,450℃煅烧未掺杂纳米管TiO2对腐植酸的催化降解效率为44%,较P-25TiO2粉末提高了11%;金属掺杂后催化效果提升明显,550℃煅烧Fe掺杂纳米管TiO2的催化效果最为显著,腐植酸去除率达77%。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...