The Effect of Inhomogeneous Phase on the Critical Temperature of Smart Meta-superconductor MgB<Subscript>2</Subscript>

The critical temperature (T_C) of MgB₂, one of the key factors limiting its application, is highly desired to be improved. On the basis of the meta-material structure, we prepared a smart meta-superconductor structure consisting of MgB₂ micro-particles and inhomogeneous phases by an ex situ process. The effect of inhomogeneous phase on the T_C of smart meta-superconductor MgB₂ was investigated. Results showed that the onset temperature (\(T_{\mathrm {C}}^{\text {on}}\)) of doping samples was lower than those of pure MgB₂. However, the offset temperature (\({T}_{\mathrm {C}}^{\text {off}}\)) of the sample doped with Y₂O₃:Eu³⁺ nanosheets with a thickness of 2 ～ 3 nm which is much less than the coherence length of MgB₂ is 1.2 K higher than that of pure MgB₂. The effect of the applied electric field on the T_C of the sample was also studied. Results indicated that with the increase of current, \({T}_{\mathrm {C}}^{\text {on}}\) is slightly increased in the samples doping with different inhomogeneous phases. With increasing current, the \({T}_{\mathrm {C}}^{\text {off}}\) of the samples doped with nonluminous inhomogeneous phases was decreased. However, the \({T}_{\mathrm {C}}^{\text {off}}\) of the luminescent inhomogeneous phase doping samples increased and then decreased with increasing current.     

Magnetocaloric-Transport Properties Correlation in La<Subscript>0.8</Subscript> Ca<Subscript>0.2</Subscript>MnO<Subscript>3</Subscript>-Doped Manganites

This investigation is interested in studying the relation between magnetocaloric effect and transport properties i La_0.8Ca_0.2MnO₃ manganite compound. The value of the magnetocaloric effect has been determined from the calculation of magnetization as a function of temperature under different external magnetic fields. This study also provides an alternative method to determine the magnetocaloric properties such as magnetic entropy change and heat capacity change on the basis of M(T, H) measurements. On the other hand, based on magnetic and resistivity measurements, the magnetocaloric properties of this compound were investigated using an equation of the form \({\Delta } S \,=\, - \alpha {\int \limits _{0}^{H}} {\left [ {\frac {\delta Ln\left (\rho \right )}{\delta T}} \right ]}_{H} dH\), which relates magnetic order to transport behavior of the compounds. As an important result, the values of MCE and the results of calculation are in good agreement with the experimental ones, which indicates the strong correlation between the electric and magnetic properties in manganites.     

Superconducting Properties of NdO<Subscript>0.5</Subscript><Emphasis Type="Bold">F</Emphasis><Subscript>0.5</Subscript>BiS<Subscript>2</Subscript> Single Crystals

We report on superconducting properties of high-quality single crystals of F-substituted NdOBiS₂ using low-temperature magnetization and transport measurements. Using the mixture of CsCl and KCl as the flux, we have synthesized our single crystals. This compound exhibits bulk superconductivity with a transition temperature of about T _c～4.6 K. The critical current density J _c as a function of temperature has been derived and decreases with the increasing temperature. We construct the phase diagram H _c2(T). The zero-temperature value for \(H_{\mathrm {c2}}^{B\parallel c}\) for value for \(T_{c}^{90~\%}\) and \(T_{c}^{0~\%}\) is estimated to be approximately 2.17 and 1.72 T respectively by using Werthamer-Helfand-Hohenberg model.     

Investigation of Magnetic,Magnetocaloric, and Critical Properties of La<Subscript>0.5</Subscript>Ba<Subscript>0.5</Subscript>MnO<Subscript>3</Subscript> Manganite

We present an extensive study of the magnetic properties of a novel La_0.5Ba_0.5MnO₃ perovskite material prepared by the hydrothermal method. The explored sample was structurally studied by the x-ray diffraction (XRD) method which confirms the formation of a pure cubic phase of a perovskite structure with Pm3m space group. The magnetic properties were probed by employing temperature M (T) and external magnetic field M (μ_oH) dependence of magnetization measurements. A magnetic phase transition from ferromagnetic to paramagnetic phase occurs at 339 K in this sample. The maximum magnetic entropy change (\(\left | {{\Delta } S}_{M}^{\max } \right |\)) took a value of 1.4 J kg^??1 K^??1 at the applied magnetic field of 4.0 T for the explored sample and has also been found to occur at Curie temperature (T_C). This large entropy change might be instigated from the abrupt reduction of magnetization at T_C. The magnetocaloric effect (MCE) is maximum at T_C as represented by M (μ_oH) isotherms. The relative cooling power (RCP) is 243.2 J kg^??1 at μ_oH =?4.0 T. Moreover, the critical properties near T_C have been probed from magnetic data. The critical exponents δ, β, and γ with values 3.82, 0.42, and 1.2 are close to the values predicted by the 3D Ising model. Additionally, the authenticity of the critical exponents has been confirmed by the scaling equation of state and all data fall on two separate branches, one for T < T_C and the other for T > T_C, signifying that the critical exponents obtained in this work are accurate.     

Electrical,Thermal and Spectroscopic Characterization of Bulk Bi<Subscript>2</Subscript>Se<Subscript>3</Subscript> Topological Insulator

We report the electrical (angular magneto-resistance and Hall), thermal (heat capacity) and spectroscopic (Raman, X-ray photoelectron, angle-resolved photoelectron) characterization of a bulk Bi₂Se₃ topological insulator, which was grown by self-flux method through solid-state reaction from high-temperature (950^°C) melt and slow cooling (2^°C/h) of constituent elements. Bi₂Se₃ exhibited metallic behaviour down to 5 K. Magneto-transport measurements revealed linear up to 400 and 30% magneto-resistance (MR) at 5 K under a 14-T field in perpendicular and parallel field directions, respectively. We noticed that the MR of Bi₂Se₃ is very sensitive to the angle of the applied field. The MR is maximum when the field is normal to the sample surface, while it is minimum when the field is parallel. The Hall coefficient (R _H) is seen nearly invariant with a negative carrier sign down to 5 K albeit having near-periodic oscillations above 100 K. The heat capacity (C _p) versus temperature plot is seen without any phase transitions down to 5 K and is well fitted (C _p = γ T + β T ³) at low temperature with a calculated Debye temperature (?? _D) value of 105.5 K. Clear Raman peaks are seen at 72, 131 and 177 cm^?1 corresponding to A\(_{\mathrm {1g}}^{1}\), E\(_{\mathrm {g}}^{2}\) and A\(_{1\mathrm {g}}^{2}\), respectively. Though two distinct asymmetric characteristic peak shapes are seen for Bi 4f_7/2 and Bi 4f_5/2, the Se 3d region is found to be broad, displaying the overlapping of spin-orbit components of the same. Angle-resolved photoemission spectroscopy (ARPES) data of Bi₂Se₃ revealed distinctly the bulk conduction bands (BCB), surface state (SS), Dirac point (DP) and bulk valence bands (BVB), and 3D bulk conduction signatures are clearly seen. Summarily, a host of physical properties for the as-grown Bi₂Se₃ crystal are reported here.     

Effect of Zr Addition on Bi<Subscript>1.8</Subscript>Pb<Subscript>0.4</Subscript>Sr<Subscript>2.0</Subscript>Ca<Subscript>1.1</Subscript>Cu<Subscript>2.1</Subscript>O<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> Superconductor

The polycrystalline Bi_1.8Pb_0.4Sr_2.0Ca_1.1Cu_2.1 M_xO _y , with M = Zr (x = 0.0, 0.02, 0.04), were synthesized by solid-state reaction method and studied by X-ray diffraction analysis (XRD), scanning electron microscopy equipped with energy dispersive of X-ray analysis (SEM/EDX) and resistivity versus temperature measurements. The influence of the Zr addition on the Tc and microstructure properties of the superconducting compounds has been studied. SEM observations show whiskers grains randomly distributed and microstructural change due to the addition of Zr. The ZrO₂ was incorporated into the crystalline structure of BSCCO system in all samples. The crystallographic structure remains in a tetragonal form where a= b≠c. Generally, all samples exhibit semiconductor behaviour above \(T_{\mathrm {c}}^{\text {onset}}\). The onset critical temperature \(T_{\mathrm {c}}^{\text {onset}}\) increases up to 86 with x = 0.02. There is an enhancement in the critical temperature for doped samples as compared with pure Bi_1.8Pb_0.4Sr_2.0Ca_1.1Cu_2.1O _y .Changes in superconducting properties of ZrO₂ nanoparticle added Bi-2212 system were discussed.     

Magnetic Entropy Change by Mean-Field Theory for the Second-Order Phase Transition Manganite Nd<Subscript>0.6</Subscript>Sr<Subscript>0.3</Subscript>Ca<Subscript>0.1</Subscript>Mn<Subscript>0.975</Subscript>Fe<Subscript>0.025</Subscript>O<Subscript>3</Subscript>

In this work, we are going to show the method based on mean-field scaling for the Nd_0.6Sr_0.3Ca_0.1Mn_0.975Fe_0.025 O₃ sample, where from scaling of experimental magnetization data, the mean-field exchange parameter λ and the f function of the equation of state \(M(T,H)=B_{S} [\frac {\left ({H+H_{\text {ex}}} \right )}{T}]\) are directly determined. The scaling approach allows finding the dependence of H _ex on T or higher powers of M, which determine the order of the phase transition. Quantum spin number has been determined. In this study, we use \(\left | {\Delta S_{M} (T)} \right |\) obtained from isothermal magnetization measurements; we compare this result to mean-field theory fittings from a novel scaling method through the use of theoretical results S, g, and λ. The obtained results by mean-field theory are suitable and in good agreement with the classical Maxwell relation.     

Low Magnetic Field Magnetocaloric Effect in $\text {Gd}_{\mathrm {5-}_{x}}$EuxGe4

The magnetocaloric effect is investigated for \(\text {Gd}_{\mathrm {5-}_{x}}\)Eu _x Ge₄ (0.25 ≤ x ≤ 2) system near a phase transition from a ferromagnetic to a paramagnetic state as a function of temperature with low external magnetic field change of 100 Oe. The sample with x = 1 has the smallest value of maximum magnetic entropy change and the specific heat change, and highest values of full-width at half-maximum and relative cooling power. The results indicate that the \(\text {Gd}_{\mathrm {5-}_{x}}\)Eu _x Ge₄ system has a prospective application for magnetic refrigerant in an extended high temperature range. Consequently, \(\text {Gd}_{\mathrm {5-}_{x}}\)Eu _x Ge₄ compounds are very attractive candidates for magnetic refrigeration applications, especially nitrogen liquefier.     

Effect of the Interfacial Disorder on the Magnetotransport Properties in Ni<Subscript>81</Subscript>Fe<Subscript>19</Subscript>/Ti<Subscript>10</Subscript><Emphasis Type="Italic">W</Emphasis><Subscript>90</Subscript> Multilayers

This work is a study of the interface structure effect on the magnetotransport properties in Ni₈₁Fe₁₉/Ti₁₀ W ₉₀ magnetic multilayer. The overall weakness showed by experimental magnetoresistance rate \(\text {MR}_{\exp }\) is probably due to a degradation of the interface quality caused by the apparition of a disordered phase NiFeW at the interface. Thus, we propose in this paper an extension to the Johnson-Camley semi classical model that takes in consideration the evolution of the interface structure, which makes it possible to reproduce quite faithfully the experimental results \(\text {MR}_{\exp } (t_{\text {NiFe}})\) for all ranges of magnetic layer thicknesses, confirming the important role of the interface structure on the electronic transport properties.     

Scaling behavior of dynamic hysteresis in Bi<Subscript>3.15</Subscript>Nd<Subscript>0.85</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> ceramics

The scaling behavior of dynamic hysteresis was investigated in Bi_3.15Nd_0.85Ti₃O₁₂ bulk ceramics at a frequency of 1–1000 Hz and an external electric field amplitude of 79–221 kV/cm. The scaling behavior at low amplitude (E ₀ ≤ 114 kV/cm) takes the form of \(\langle A \rangle \propto f^{ - 0.013} E_{0}^{0.7}\) for low frequency (f ≤ 200 Hz) and \(\langle A \rangle \propto f^{ - 0.013} E_{0}^{0.22}\) for high frequency (f > 200 Hz), where \(\langle A \rangle\) is the area of hysteresis loop and f and E ₀ are frequency and amplitude of external electric field, respectively. At high amplitude (E ₀ > 114 kV/cm), we obtain \(\langle A \rangle \propto f^{0.011} E_{0}^{1.163}\) at low frequency and \(\langle A \rangle \propto f^{ - 0.015} E_{0}^{0.7}\) at high frequency. At low E ₀, the contribution to the scaling relation mainly results from reversible domain switching, while at high E ₀ reversible and irreversible domain switching concurrently contribute to the scaling relation.     

Ab Initio Study of Structural,Electronic, and Magnetic Properties of $\mathrm {A}_{1-x}^{\text {III}}$MnxBVI: In1−xMnxS-Diluted Magnetic Semiconductor

First-principles density functional calculations on the new class of diluted magnetic semiconductor \(A_{1-x}^{III}{Mn}_{x}B^{VI}\) In_1?x Mn _x S for x =?0.25 and 0.5 are investigated to study the structural, electronic, and magnetic properties, employing the full-potential linearized augmented plane wave method. Electronic band structures and density of states revealed a half-metallic character of In_1?x Mn _x S and show the stability of anti-ferromagnetic states as compared with ferromagnetic states. The calculated exchange constants J _dd are in good agreement with experimental and theoretical results on magnetic properties of single crystalline \(\mathrm {A}_{1-x}^{\text {III}}{\text {Mn}}_{x}\mathrm {B}^{\text {VI}}\) in the anti-ferromagnetic case. Our predicated calculations on the s,p-d exchange constants N ₀ α and N ₀ β show that they are lower than in \(\mathrm {A}_{1-x}^{\text {II}}{\text {Mn}}_{x}\mathrm {B}^{\text {VI}}\) DMS. The local environment is found tetrahedral as in the II–VI DMS and other (III,Mn) VI compounds. The total magnetic moment for In_1?x Mn _x S for different concentrations is in accordance with the exact value 5 μ _B and comes mainly from impurity Mn. The local magnetic moments of Mn ions are reduced from their free space charges values due to the p-d hybridization which produces small magnetic moments on the nonmagnetic In and S sites. The Curie temperature of In_1?x Mn _x S is calculated within the mean field approximation and compared with other DMS systems.     

Thermal Conductivity of Pyroclastic Soil (<Emphasis Type="BoldItalic">Pozzolana</Emphasis>) from the Environs of Rome

The paper reveals the experimental procedure and thermo-physical characteristics of a coarse pyroclastic soil (Pozzolana), from the neighborhoods of Rome, Italy. The tested samples are comprised of 70.7 % sand, 25.9 % silt, and 3.4 % clay. Their mineral composition contained 38 % pyroxene, 33 % analcime, 20 % leucite, 6 % illite/muscovite, 3 % magnetite, and no quartz content was noted. The effective thermal conductivity of minerals was assessed to be about \(2.14\,\hbox {W}{\cdot } \hbox {m}^{-1}{\cdot } \hbox {K}^{-1}\). A transient thermal probe method was applied to measure the thermal conductivity (\(\lambda \)) over a full range of the degree of saturation \((S_{\mathrm{r}})\), at two porosities (n) of 0.44 and 0.50, and at room temperature of about \(25\,^{\circ }\hbox {C}\). The \(\lambda \) data obtained were consistent between tests and showed an increasing trend with increasing \(S_{\mathrm{r}}\) and decreasing n. At full saturation (\(S_{\mathrm{r}}=1\)), a nearly quintuple \(\lambda \) increase was observed with respect to full dryness (\(S_{\mathrm{r}}=0\)). In general, the measured data closely followed the natural trend of \(\lambda \) versus \(S_{\mathrm{r}}\) exhibited by published data at room temperature for other unsaturated soils and sands. The measured \(\lambda \) data had an average root-mean-squared error (RMSE) of \(0.007\,\hbox {W}{\cdot } \hbox {m}^{-1}{\cdot } \hbox {K}^{-1}\) and \(0.008\,\hbox {W}{\cdot } \hbox {m}^{-1}{\cdot } \hbox {K}^{-1}\) for n of 0.50 and 0.44, respectively, as well as an average relative standard deviation of the mean at the 95 % confidence level \((\hbox {RSDM}_{0.95})\) of 2.21 % and 2.72  % for n of 0.50 and 0.44, respectively.     

Reactionary processes during mechanical treatment of mixtures of ZnO and MnO<Subscript>2</Subscript>. I. Formation of defects and solid solution

Kinetics of defects formation, reaction process and formation of solid solution in powder mixtures of ZnO and MnO₂ induced by prolonged mechanical treatment (MT) have been investigated (X-ray, FTIR, EPR). At MT in zones of deformation-destruction the different defects (\( {\text{V}}_{{\text{Zn}}}^ - :{\text{Zn}}_{\text{i}}^{\text{0}} \) (I), \( {\text{V}}_{{\text{Zn}}}^ - \) (II), and \( {\text{(V}}_{{\text{Zn}}}^ - {\text{)}}_{\text{2}}^ - \) (III) centers at all) are forming. The defects have various physical and chemical properties, and have different activation energies of annealing, E_act The part of these defects is responsible for the processes of hydration and carbonation of samples. In turn, the formation of defects is accompanied by development of various mechanothermical processes, which increase temperature of the sample, T _MT, with the increasing of duration of MT, t _MT. The increasing of t _MT activates the reactionary processes: promotes a consecutive annealing the «low-temperature» defects having small values of E_act (I, II and III) and also leads to formation of Mn²⁺-doped Zn(OH)₂. With the further increase of t _MT, the process of MT is accompanied by an increasing of temperature of samples up to equilibrium, T _eq and accumulation of “high-temperature” defects in the sample. As a result, in the sample the conditions for intensification of volumetric diffusion processes and formation of Mn²⁺-doped ZnO were created.     

Phenomenological model of the magnetocaloric effect and its correlation with critical behavior near room temperature in La<Subscript>0.7</Subscript>Ca<Subscript>0.2</Subscript>Sr<Subscript>0.1</Subscript>MnO<Subscript>3</Subscript> manganite

In this paper, we investigate the field dependence of the magnetocaloric properties of La_0.7Ca_0.2Sr_0.1MnO₃ powder sample using a phenomenological model. Our compound was elaborated by the conventional solid state reaction. The model parameters were determined from the magnetization data and were used to give better fits to magnetic transition and to calculate the magnetocaloric quantities. The magnetocaloric parameters such as the maximum of the magnetic entropy change \(\Delta S_M^{max}\) and the relative cooling power RCP, have been determined from the calculation of the magnetization as a function of temperature under several magnetic applied field. Thus, from the magnetocaloric results, such as RCP?≈?b(μ₀H)^1+1/δ and T_peak???T_C ≈ b (µ₀H)^1/Δ, the critical exponents values related to the magnetic transition have been determined. The estimated results are close to those expected by the tricritical mean-field model. Furthermore, the values of the ferromagnetic transition temperature T_C, as well as the critical exponents β, γ and δ obtained by the theoretical model, are compared with those obtained by other various techniques (such as the modified Arrott plots, the Kouvel–Fisher method and the critical isotherm analysis). A good agreement has been found in the vicinity of the Curie temperature.     

Inducement of Itinerant Electron Transport in Charge-Ordered Pr<Subscript>0.6</Subscript>Ca<Subscript>0.4</Subscript>MnO<Subscript>3</Subscript> by Ba Doping

The effects of Ba ²⁺ doping on the electrical and magnetic properties of charge-ordered Pr_0.6Ca_0.4MnO₃ were investigated through electrical resistivity and AC susceptibility measurements. X-ray diffraction data analysis showed an increase in unit cell volume with increasing Ba ²⁺ content indicating the possibility of substituting Ba ²⁺ for the Ca-site. Electrical resistivity measurements showed insulating behavior and a resistivity anomaly at around 220 K. This anomaly is attributed to the existence of charge ordering transition temperature, \(T^{\mathrm {R}}_{\text {CO}}\) for the x = 0 sample. The Ba-substituted samples exhibited metallic to insulator transition (MI) behavior, with transition temperature, T _MI, increasing from ～98 K (x = 0.1) to ～122 K (x = 0.3). AC susceptibility measurements showed ferromagnetic to paramagnetic (FM-PM) transition for Ba-substituted samples with FM-PM transition temperature, T _c, increasing from ～121 K (x = 0.1) to ～170 K (x = 0.3), while for x = 0, an antiferromagnetic to paramagnetic transition behavior with transition temperature, T _N, ～170 K was observed. In addition, inverse susceptibility versus T plot showed a deviation from the Curie–Weiss behavior above T _c, indicating the existence of the Griffiths phase with deviation temperature, T _G, increasing from 160 K (x = 0.1) to 206 K (x = 0.3). Magnetoresistance, MR, behavior indicates intrinsic MR mechanism for x = 0.1 which changed to extrinsic MR for x > 0.2 as a result of Ba substitution. The weakening of charge ordering and inducement of ferromagnetic metallic (FMM) state as well as increase in both T _c and T _MI are suggested to be related to the increase of tolerance factor, τ, and increase of e _g ?electron bandwidth as average ionic radius at A-site, <r _A> increased with Ba substitution. The substitution may have reduced MnO₆ octahedral distortion and changed the Mn–O–Mn angle which, in turn, promotes itinerancy of charge carrier and enhanced double exchange mechanism. On the other hand, increase in A-site disorder, which is indicated by the increase in σ ² is suggested to be responsible for the widening of the difference between T _c and T _MI.     

X-ray Photoelectron Spectroscopy,Magnetotransport and Magnetisation Study of Nb<Subscript>2</Subscript>PdS<Subscript>5</Subscript> Superconductor

In the present report, we investigate various properties of the Nb₂PdS₅ superconductor. Scanning electron microscopy displayed slabs like laminar growth of Nb₂PdS₅ while X-ray photoelectron spectroscopy exhibited the hybridisation of sulphur (2p) with both palladium (3d) and niobium (3d). High-field (140 kOe) magneto-transport measurements revealed that superconductivity (\(T_{c}^{\text {onset}} =?7\) K and T cρ=?0 = 6.2 K) of the studied Nb₂PdS₅ material is quite robust against magnetic field with the upper critical field (H _c2) outside the Pauli paramagnetic limit. Thermally activated flux flow (TAFF) of the compound showed that resistivity curves follow Arrhenius behaviour. The activation energy for Nb₂PdS₅ is found to decrease from 15.15 meV at 10 kOe to 2.35 meV at 140 kOe. Seemingly, the single vortex pinning is dominant in low-field regions, while collective pinning is dominant in high-field region. The temperature dependence of AC susceptibility confirmed the T _c at 6 K, further varying amplitude and frequency, showed well-coupled granular nature of superconductivity. The lower critical field (H _c1) is extracted from DC magnetisation measurements at various T below T _c. It is found that H _c1(T) of Nb₂PdS₅ material seemingly follows the multiband nature of superconductivity.     

Prediction of Magnetocaloric Effect by a Phenomenological Model and Critical Behavior for La<Subscript>0.78</Subscript>Dy<Subscript>0.02</Subscript>Ca<Subscript>0.2</Subscript>MnO<Subscript>3</Subscript> Compound

The La_0.78Dy_0.02Ca_0.2MnO₃ (LDCMO) compound prepared via high-energy ball-milling (BM) presents a ferromagnetic-to-paramagnetic transition (FM-PM) and undergoes a second-order phase transition (SOFT). Based on a phenomenological model, magnetocaloric properties of the LDCMO compound have been studied. Thanks to this model, we can predict the values of the magnetic entropy change ΔS, the full width at half-maximum δ T _FWHM, the relative cooling power (RCP), and the magnetic specific heat change ΔC _p for our compound. The significant results under 2 T indicate that our compound could be considered as a candidate for use in magnetic refrigeration at low temperatures. In order to further understand the FM-PM transition, the associated critical behavior has been investigated by magnetization isotherms. The critical exponents estimated by the modified Arrott plot, the Kouvel–Fisher plot, and the critical isotherm technique are very close to those corresponding to the 3D-Ising standard model (β = 0.312 ± 0.07, γ = 1.28 ± 0.02, and δ = 4.80).Those results revealed a long-range ferromagnetic interaction between spins.     

Experimental Study of the Thermodynamic Properties of Diethyl Ether (DEE) at Saturation

The isochoric heat capacities \({({C_{V1}^{\prime}} ,{C_{V1}^{\prime\prime}},{C_{V2}^{\prime}},{C_{V2}^{\prime\prime}})}\), saturation densities (\({\rho _{\rm S}^{\prime}}\) and \(({\rho_{\rm S}^{\prime\prime})}\)), vapor pressures (P _S), thermal-pressure coefficients \({\gamma_V=\left({\partial P/\partial T}\right)_V}\), and first temperature derivatives of the vapor pressure γ _S = (dP _S/dT) of diethyl ether (DEE) on the liquid–gas coexistence curve near the critical point have been measured with a high-temperature and high-pressure nearly constant-volume adiabatic piezo-calorimeter. The measurements of \({({C_{V1}^{\prime}} ,{C_{V1}^{\prime\prime}},{C_{V2}^{\prime}},{C_{V2}^{\prime\prime}})}\) were made in the liquid and vapor one- and two-phase regions along the coexistence curve. The calorimeter was additionally supplied with a calibrated extensometer to accurately and simultaneously measure the PVT, C _V VT, and thermal-pressure coefficient, γ _V , along the saturation curve. The measurements were carried out in the temperature range from 416 K to 466.845 K (the critical temperature) for 17 liquid and vapor densities from 212.6 kg · m^?3 to 534.6 kg · m^?3. The quasi-static thermo- (reading of PRT, T ? τ plot) and baro-gram (readings of the tensotransducer, P ? τ plot) techniques were used to accurately measure the phase-transition parameters (P _S ,ρ _S ,T _S) and γ _V . The total experimental uncertainty of density (ρ _S), pressure (P _S), temperature (T _S), isochoric heat capacities \({({C_{V1}^{\prime}} ,{C_{V1}^{\prime\prime}},{C_{V2}^{\prime}},{C_{V2}^{\prime\prime}})}\), and thermal-pressure coefficient, γ _V , were estimated to be 0.02 % to 0.05 %, 0.05 %, 15 mK, 2 % to 3 %, and 0.12 % to 1.5 %, respectively. The measured values of saturated caloric \({({C_{V1}^{\prime}} ,{C_{V1}^{\prime\prime}},{C_{V2}^{\prime}},{C_{V2}^{\prime\prime}})}\) and saturated thermal (P _S, ρ _S, T _S) properties were used to calculate other derived thermodynamic properties C _P , C _S, W, K _T , P _int, ΔH _vap, and \({\left({\partial V/\partial T}\right)_P^{\prime}}\) of DEE near the critical point. The second temperature derivatives of the vapor pressure, (d² P _S/dT ²), and chemical potential, (d² μ/dT ²), were also calculated directly from the measured one- and two-phase liquid and vapor isochoric heat capacities \({({C_{V1}^{\prime}} ,{C_{V1}^{\prime\prime}},{C_{V2}^{\prime}},{C_{V2}^{\prime\prime}})}\) near the critical point. The derived values of (d² P _S/dT ²) from calorimetric measurements were compared with values calculated from vapor–pressure equations. The measured and derived thermodynamic properties of DEE near the critical point were interpreted in terms of the “complete scaling” theory of critical phenomena. In particular, the effect of a Yang–Yang anomaly of strength R _μ on the coexistence-curve diameter behavior near the critical point was studied. Extended scaling-type equations for the measured properties P _S (T), ρ _S (T), and \({({C_{V1}^{\prime}} ,{C_{V1}^{\prime\prime}},{C_{V2}^{\prime}},{C_{V2}^{\prime\prime}})}\) as a function of temperature were developed.     

Characterization and optical properties of $$\hbox {Pr}_{2}\hbox {O}_{3}$$-doped molybdenum lead-borate glasses

\(\hbox {Pr}^{3+}\) doped molybdenum lead-borate glasses with the chemical composition 75PbO?[25–(x \(+\) y)\(\hbox {B}_{2}\hbox {O}_{3}]\)–\(y\hbox {MoO}_{3}\)–\(x\hbox {Pr}_{2}\hbox {O}_{3}\) (where \(x = 0.5\) and 1.0 mol% and \(y = 0\) and 5 mol%) were prepared by conventional melt-quenching technique. Thermal, optical and structural analyses are carried out using DSC, UV and FTIR spectra. The physical parameters, like glass transition \((T_{\mathrm{g}})\), stability factor \((\Delta T)\), optical energy band gap \((E_{\mathrm{gopt}})\), of these glasses have been determined as a function of dopant concentration. The \({T}_{\mathrm{g}}\) and optical energy gaps of these glasses were found to be in the range of 290–350\({^{\circ }}\hbox {C}\) and 2.45–2.7 eV, respectively. Stability of the glass doped with \(\hbox {Pr}^{3+}\) is found to be moderate (\(\sim \)40). The results are discussed using the structural model of Mo–lead-borate glass.     

High-pressure studies of superconductivity in $$\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}$$

\(\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}\) crystallizes in tetragonal CeOBiS\(_{2}\) structure (S. G. P4/nmm). We have investigated the effect of pressure on magnetization measurements. Our studies suggest improved superconducting properties in polycrystalline samples of \(\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}\). The \(T_{\mathrm{c}}\) in our sample is 5.3 K, at ambient pressure, which is marginal but definite enhancement over \(T_{\mathrm{c}}\) reported earlier (= 5.1 K). The upper critical field \(H_{\mathrm{c}2}\)(0) is greater than 3 T, which is higher than earlier report on this material. As determined from the M–H curve, both \(H_{\mathrm{c}2}\) and \(H_{\mathrm{c}1}\) decrease under external pressure P (0 \(\le P \le \) 1 GPa). We observe a decrease in critical current density and transition temperature on applying pressure in \(\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}\).