Synthesis of SrFe<Subscript>12</Subscript>O<Subscript>19</Subscript>/SiO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> composites with core/shell/shell nano-structure and evaluation of their photo-catalytic efficiency for degradation of methylene blue

The SrFe₁₂O₁₉/SiO₂/TiO₂ nanostructures with hard magnetic core were successfully synthesized through the facile and efficient wet chemical processes. At first, nanocrystalline strontium hexaferrite (SrFe₁₂O₁₉) powder was prepared using a new co-precipitation route in ethanol/water media. In the next step, SrFe₁₂O₁₉/SiO₂ composites were produced by well-known Stöber method using tetraethyl orthosilicate as precursor. Finally titania was coated on SrFe₁₂O₁₉/SiO₂ composite particles using titanium n-butoxide precursor. The core/shell/shell nanostructures have been characterized by means of X-ray diffraction, vibrating sample magnetometer, Fourier transform infrared spectra, field emission scanning electron microscopy, and transmission electron microscopy equipped with an energy-dispersive X-ray spectroscopy detector. The catalytic activity of SrFe₁₂O₁₉/SiO₂/TiO₂ composites has been investigated in the degradation of methylene blue dye under UV illumination. The results indicated that the obtained SrFe₁₂O₁₉/SiO₂/TiO₂ composite has photo-catalytic properties and can be retrieved by magnetic separation. The photo-degradation of methylene blue dye was about 80% in the presence of photo-catalyst powder at irradiation time of 180 min. Recycled composite particles could be used again.     

The Effect of Annealing on Phase Stability and Magnetic Properties of Hexaferrite BaFe<Subscript>12</Subscript><Emphasis Type="Italic">O</Emphasis><Subscript>19</Subscript>

The hexaferrite BaFe₁₂ O ₁₉ phase was synthesized through the mechanical alloying process followed by subsequent annealing. Rietveld refinements of as-milled powder annealed at 700 ^°C confirm the formation of the BaFe₁₂ O ₁₉ phase with the presence of an important amount of the α-Fe₂ O ₃ phase. Thus, prior mechanical milling shows much lower reaction temperature and less reaction time compared to conventional methods. Further annealing up to 900 and 1100 ^°C could not enable the formation of a single BaFe₁₂ O ₁₉ phase, reaching an optimum phase composition ratio close to BaFe₁₂ O ₁₉/ α-Fe₂ O ₃ 70/30. The crystallite size was found to be in the nanoscale level but increases with increasing temperature (BaFe₁₂ O ₁₉ = 20–62 nm; α-Fe₂ O ₃ = 31–74 nm). SEM micrographs show that as the annealing temperature rises, the particles become more regular with sharp edges and hexagonal-like shapes. Magnetic measurements reveal that both M _s and M _r increase with annealing temperature to reach maximum values at 900 ^°C then remain unchanged, associated with phase composition. The coercivity H _c increases upon annealing up to 700 ^°C to a much higher value, from 1.7 kOe for as-milled powder to 4.8 kOe. Its value then decreases, attributed to grain (particle) growth (formation of larger particles) due to high annealing temperatures: 900–1100 ^°C. The obtained composites show very interesting magnetic properties and can be considered for potential applications, such as hyperthermia, heavy metal and dye removal, and hard/soft magnetic composites.     

Synthesis and structure of the CsSmP<Subscript>4</Subscript>O<Subscript>12</Subscript> cyclotetraphosphate (cubic CsNdP<Subscript>4</Subscript>O<Subscript>12</Subscript> structure)

CsSmP₄O₁₂ crystals have been prepared at 300°C in molten polyphosphoric acids containing Cs, Mg, and Sm cations, and their crystal structure has been determined: sp. gr. I \(\bar 4\) 3d, a = 15.1225(8) Å, Z = 12, CsNdP₄O₁₂ structure.     

Solid-state reactions in the system Li<Subscript>2</Subscript>CO<Subscript>3</Subscript>-Na<Subscript>2</Subscript>CO<Subscript>3</Subscript>-Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>-Ta<Subscript>2</Subscript>O<Subscript>5</Subscript>

The formation mechanisms of Li _x Na_{1 ?x} Ta _y Nb_{1 ? y} O₃ perovskite solid solutions in the Li₂CO₃-Na₂CO₃-Nb₂O₅-Ta₂O₅ system have been studied by x-ray diffraction, differential thermal analysis, thermogravimetry, IR spectroscopy, and mass spectrometry at temperatures from 300 to 1100°C. The results indicate that the synthesis of Li _x Na_{1 ? x} Ta _y Nb_{1 ? y} O₃ solid solutions involves a complex sequence of consecutive and parallel solid-state reactions. An optimized synthesis procedure for Li _x Na_{1 ? x} Ta _y Nb_{1 ? y} O₃ solid solutions is proposed.     

Synthesis and High-Temperature Heat Capacity of Dy<Subscript>2</Subscript>Ge<Subscript>2</Subscript>O<Subscript>7</Subscript> and Ho<Subscript>2</Subscript>Ge<Subscript>2</Subscript>O<Subscript>7</Subscript>

The Dy₂Ge₂O₇ and Ho₂Ge₂O₇ pyrogermanates have been prepared by solid-state reactions in several sequential firing steps in the temperature range 1237–1473 K using stoichiometric mixtures of Dy₂O₃ (or Ho₂O₃) and GeO₂. The heat capacity of the synthesized germanates has been determined as a function of temperature by differential scanning calorimetry in the range 350–1000 K. The experimentally determined C _p (T) curves of the dysprosium and holmium germanates have no anomalies and are well represented by the Maier–Kelley equation. The experimental C _p (T) data have been used to evaluate the thermodynamic functions of the Dy₂Ge₂O₇ and Ho₂Ge₂O₇ pyrogermanates: enthalpy increment H°(T)–H°(350 K), entropy change S°(T)–S°(350 K), and reduced Gibbs energy Ф°(T).     

Critical Behavior of La<Subscript>0.67</Subscript>Ba<Subscript>0.33</Subscript>Mn<Subscript>0.95</Subscript>Fe<Subscript>0.05</Subscript>O<Subscript>3</Subscript> Manganite

The critical behavior of perovskite manganite La_0.67Ba_0.33Mn_0.95Fe_0.05O₃ at the ferromagnetic–paramagnetic has been analyzed. The results show that the sample exhibited the second-order magnetic phase transition. The estimated critical exponents derived from the magnetic data using various such as modified d’Arrott plot Kouvel–Fisher method and critical magnetization M(T _C, H). The critical exponents values for the La_0.67Ba_0.33Mn_0.95Fe_0.05O₃ are close to those expected from the mean field model β = 0.504 ± 0.01 with T _C = 275661 ± 0.447 (from the temperature dependence of the spontaneous magnetization below T _C ), γ = 1.013 ± 0.017 with T _C = 276132 ± 0.452 (from the temperature dependence of the inverse initial susceptibility above T _C ), and δ = 3.0403 ± 0.0003. Moreover, the critical exponents also obey the single scaling equation of M(H, ε) = |ε| ^β f _±(H/|ε| ^β+γ ).     

Compounds WAl<Subscript>4</Subscript>, WAl<Subscript>3</Subscript>, W<Subscript>3</Subscript>Al<Subscript>7</Subscript>, and WAl<Subscript>2</Subscript> and Al-W-N combustion products

X-ray diffraction data are presented for combustion products in the Al-W-N system. New, nonequilibrium intermetallic compounds have been identified, their diffraction patterns have been indexed, and their unit-cell parameters have been determined. The phases α-and β-WAl₄ are shown to exist in three isomorphous forms, differing in unit-cell centering. The phases α′-, α″-, and α?-WAl₄ are monoclinic, with a ₀ = 5.272 Å, b ₀ = 17.770 Å, c ₀ = 5.218 Å, β = 100.10°; point groups C12/c1, A12/n1, I12/a1, respectively. The phases β′-, β″-, and β?-WAl₄ are monoclinic, with a ₀ = 5.465 Å, b ₀ = 12.814 Å, c ₀ = 5.428 Å, β = 105.92°; point groups A112/m, B112/m, I112/m, respectively. The compounds WAl₂ and W₃Al₇, identified each in two isomorphous forms, differ in cell metrics (doubling) but possess the same point group: P222. WAl ₂ ^′ : orthorhombic, a ₀ = 5.793 Å, b ₀ = 3.740 Å, c ₀ = 6.852 Å. WAl ₂ ^″ : orthorhombic, a ₀ = 11.586 Å, b ₀ = 3.740 Å, c ₀ = 6.852 Å. W₃Al ₇ ^′ : orthorhombic, Pmm2, a ₀ = 6.225 Å, b ₀ = 4.806 Å, c ₀ = 4.437 Å. W₃Al ₇ ^″ : orthorhombic, Pmm2, a ₀ = 12.500 Å, b ₀ = 4.806 Å, c ₀ = 8.874 Å. The new phase WAl₃: triclinic, P1, a ₀ = 8.642 Å, b ₀ = 10.872 Å, c ₀ = 5.478 Å, α = 104.02°, β = 64.90°, γ = 107.15°.     

Low temperature sintering and microwave dielectric properties of Li<Subscript>6</Subscript>Mg<Subscript>7</Subscript>Ti<Subscript>3</Subscript>O<Subscript>16</Subscript> ceramics with LiF additive for LTCC applications

Li₆Mg₇Ti₃O₁₆ ceramics were prepared by the conventional solid-state method with 1–5 wt% LiF as the sintering aid. Effects of LiF additions on the phase compositions, sintering characteristics, micro-structures and microwave dielectric properties of Li₆Mg₇Ti₃O₁₆ ceramics were investigated. The LiF addition could effectively lower the sintering temperature of Li₆Mg₇Ti₃O₁₆ ceramics from 1550 to 900 °C. For different LiF-doped compositions, the optimum dielectric permittivity (ε _r ) and quality factor (Q·f) values first increased and then decreased with the increase of LiF contents, whereas the temperature coefficient of resonant frequency (τ _f ) fluctuated between ??14.39 and ??8.21 ppm/°C. Typically, Li₆Mg₇Ti₃O₁₆ ceramics with 4 wt% LiF sintered at 900 °C exhibited excellent microwave dielectric properties of ε _r ?=?16.17, Q·f?=?80,921 GHz and τ _f ?=???8.21 ppm/°C, which are promising materials for the low temperature co-fired ceramics applications.     

Growth and properties of LiCu<Subscript>2</Subscript>O<Subscript>2</Subscript>-NaCu<Subscript>2</Subscript>O<Subscript>2</Subscript> crystals

Platelike Li_{1 ? x} Na _x Cu₂O₂ single crystals up to 2 × 10 × 10 mm in dimensions have been grown by slowly cooling (1 ? x)Li₂CO₃·xNa₂O₂·4CuO melts in alundum crucibles in air. Li_{1 ? x} Na _x Cu₂O₂ solid solutions in the LiCu₂O₂-NaCu₂O₂ system have been shown to exist in the composition range 0.78 < x < 1. The temperature stability ranges of NaCu₂O₂ and LiCu₂O₂ are 780–930 and 890–1050°C, respectively. The Mössbauer spectra and electrical conductivity of the crystals have been measured.     

The magnetic properties of BiY<Subscript>2</Subscript>Fe<Subscript>5</Subscript>O<Subscript>12</Subscript> nanoparticles doped with Cr ions

BiY₂Cr _x Fe_5?x O₁₂ (x = 0, 0.05, 0.1, 0.2, 0.3) nanocrystals were synthesized by using a sol-gel method. Samples were characterized by the powder X-ray diffraction (XRD), the thermal gravity analysis (TGA) and the differential thermal analysis (DTA), the vibrating sample magnetometer(VSM) and Mössbauer spectrums. The average sizes of the particles were determined by the Scherrer’s formula. The special Ms and Mössbauer spectra of BiY₂Cr _x Fe_5?x O₁₂ nanocrystals are researched at room temperature. It is seen that the special Mss of samples are initially increased with increasing Cr³⁺ content (x < 0.1), and decreased with increasing content of Cr³⁺ ions (x > 0.1).     

Electric-field effect on crystal growth in the Li<Subscript>3</Subscript>PO<Subscript>4</Subscript>-Li<Subscript>4</Subscript>GeO<Subscript>4</Subscript>-Li<Subscript>2</Subscript>MoO<Subscript>4</Subscript>-LiF system

We have studied the electric-field effect on crystallization processes in the Li₃PO₄-Li₄GeO₄-Li₂MoO₄-LiF system. In zero field, Li_3+x P_1?x Ge _x O₄ (x = 0.31) crystals were grown on the cathode under the conditions of this study. At low applied voltages (≤ 0.5 V), we obtained Li₂MoO₄, Li₂GeO₃, and Li_1.3Mo₃O₈. In the range V = 0.5–1 V, crystals of Li_3+x P_1?x Ge _x O₄ solid solutions with x = 0.17, 0.25, 0.28, 0.29, and 0.36 were obtained. An applied electric field was shown to reduce the melting temperature of the starting mixtures and the crystallization onset temperature.     

Very high thermal stability with excellent dielectric,and non-ohmics properties of Mg-doped CaCu<Subscript>3</Subscript>Ti<Subscript>4.2</Subscript>O<Subscript>12</Subscript> ceramics

In this work, the nominal CaCu_3?xMg_xTi_4.2O₁₂ (0.00, 0.05 and 0.10) ceramics were prepared by sintering pellets of their precursor powders obtained by a polymer pyrolysis solution method at 1100 °C for different sintering time of 8 and 12 h. Very low loss tangent (tanδ)?<?0.009–0.014 and giant dielectric constant (ε′) ～?1.1?×?10⁴–1.8?×?10⁴ with excellent temperature coefficient (Δε′) less than ±?15% in a temperature range of ??60 to 210 °C were achieved. These excellent performances suggested a potent application of the ceramics for high temperature X8R and X9R capacitors. It was found that tanδ values decreased with increasing Mg²⁺ dopants due to the increase of grain boundary resistance (R_gb) caused by the very high density of grain, resulting from the substitution of small ionic radius Mg²⁺ dopants in the structure. In addition, CaCu_3?xMg_xTi_4.2O₁₂ ceramics displayed non-linear characteristics with the significant enhancements of a non-linear coefficient (α) and a breakdown field (E_b) due to Mg²⁺doping. The high values of ε′ (14012), α (13.64) and E_b (5977.02 V/cm) with very low tanδ value (0.009) were obtained in a CaCu_2.90Mg_0.10Ti_4.2O₁₂ ceramic sintered at 1100 °C for 8 h.     

Solid-state synthesis,characterization, and properties of Ni<Subscript>4</Subscript>Nb<Subscript>2</Subscript>O<Subscript>9</Subscript>-based solid solutions

In this paper, we report the solid-state synthesis, characterization, and physicochemical properties of Ni_4–x Zn _x Nb₂O₉ (x = 0, 0.1, 0.3, 0.5, 0.75, 1.0) zinc-containing nickel niobates and Ni₄Nb_2–x Ta _x O₉ (x = 0.1, 0.3, 0.5, 1.0, 2.0) solid solutions. The materials were characterized by X-ray diffraction. We determined the particle size composition of the synthesized powders, assessed their chemical stability in acid media, obtained IR spectra of the solid solutions, and measured their electrical conductivity as a function of temperature. Some of the solid solutions were used to fabricate and characterize nickel-selective electrodes, which were successfully tested in ion-selective measurements.     

Synthesis and high-temperature heat capacity of Gd<Subscript>2</Subscript>Sn<Subscript>2</Subscript>O<Subscript>7</Subscript>

Gd₂Sn₂O₇ gadolinium stannate with the pyrochlore structure has been prepared by solid-state reaction and its high-temperature heat capacity has been determined by differential scanning calorimetry in the temperature range 350–1020 K. The C_p(T) data are shown to be well represented by the classic Maier–Kelley equation. The experimental C_p(T) data have been used to evaluate the thermodynamic functions of gadolinium stannate: enthalpy increment H°(T)–H°(339 K), entropy change S°(T)–S°(339 K), and reduced Gibbs energy Ф°(Т).     

Thermodynamic Properties of FeNb<Subscript>2</Subscript>O<Subscript>6</Subscript> and FeTa<Subscript>2</Subscript>O<Subscript>6</Subscript>

Empirical calculational approaches have been used to evaluate the enthalpy, entropy, heat capacity, and melting point of iron(II) niobate and iron(II) tantalate and the coefficients A, B, and C in an equation for the temperature dependence of their heat capacity. The melting point of FeTa₂O₆ has been experimentally determined to be 1891 ± 5 K. The calculated heat capacity (C°_p (298.15 K)) of iron tantalate and the Gibbs energies of formation of FeN₂O₆ and FeTa₂O₆ have been compared to previously reported data.     

Low temperature sintering and microwave dielectric properties of Zn<Subscript>3</Subscript>Mo<Subscript>2</Subscript>O<Subscript>9</Subscript> ceramic

Crystal structure and dielectric properties of Zn₃Mo₂O₉ ceramics prepared through a conventional solid-state reaction method were characterized. XRD and Raman analysis revealed that the Zn₃Mo₂O₉ crystallized in a monoclinic crystal structure and reminded stable up to1020 °C. Dense ceramics with high relative density (~ 92.3%) were obtained when sintered at 1000 °C and possessed good microwave dielectric properties with a relative permittivity (ε _r ) of 8.7, a quality factor (Q?×?f) of 23,400 GHz, and a negative temperature coefficient of resonance frequency (τ _f ) of around ??79 ppm/°C. With 5 wt% B₂O₃ addition, the sintering temperature of Zn₃Mo₂O₉ ceramic was successfully lowered to 900 °C and microwave dielectric properties with ε _r ?=?11.8, Q?×?f?=?20,000 GHz, and τ _f = ??79.5 ppm/°C were achieved.     

Crystal structure of KNa<Subscript>3</Subscript>[(UO<Subscript>2</Subscript>)<Subscript>5</Subscript>O<Subscript>6</Subscript>(SO<Subscript>4</Subscript>)]

The crystal structure of a previously unknown compound KNa₃[(UO₂)₅O₆(SO₄)] [space group Pbca, a = 13.2855(15), b = 13.7258(18), c = 19.712(2) Å, V = 3594.6(7) ų] was solved by direct methods and refined to R ₁ = 0.055 for 3022 reflections with |F _hkl | ≥ 4σ |F _hkl |. In the structure there are five sym-metrically nonequivalent uranyl cations. They are linked by cationcation (CC) interactions to form a pentamer whose central cation is U(2)O ₂ ²⁺ forming two three-centered CC bonds. All the uranyl ions are coordinated in the equatorial plane by five O atoms, which leads to the formation of pentagonal bipyramids sharing common edges to form layers parallel to the (100) plane. The sulfate tetrahedron links the uranyl layers into a 3D framework. The K⁺ and Na⁺ cations are arranged in framework voids. A brief review of CC interactions in U(VI) compounds is presented.     

New,thermally stable Gd<Subscript>11</Subscript>(GeO<Subscript>4</Subscript>)(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>O<Subscript>10</Subscript>-based upconversion phosphors

A series of Gd_11–x–y Yb _x Er _y GeP₃O₂₆ germanate phosphates differing in the ratio of the Yb³⁺ and Er³⁺ active ions have been synthesized, and their luminescence spectra have been measured. According to X-ray diffraction characterization results, all of the synthesized germanate phosphates are single-phase and have a triclinic structure (sp. gr. P1). We have measured upconversion luminescence spectra due to the Er^{3+ 2}H_11/2, ⁴S_3/2 → ⁴I_15/2 and ⁴F_9/2 → ⁴I_15/2 radiative transitions in the synthesized gadolinium ytterbium erbium germanate phosphates and determined the luminescence upconversion energy yield (B _en) in Gd_11–x–y Yb _x Er _y GeP₃O₂₆. The effects of the concentrations and ratio of the dopants in the Gd₁₁(GeO₄)(PO₄)₃O₁₀ germanate phosphate host on B _en and the ratio of the luminescence intensities in the red and green spectral regions (R/G) have been assessed.     

Rare-earth-doped PbTiO<Subscript>3</Subscript>-PbZrO<Subscript>3</Subscript> solid solutions

(Pb_{1 ? x} Ln _x )(Zr_0.53Ti_0.47)O₃ and (Pb_{1 ? x} Ln _x )(Zr_0.65Ti_0.35)O₃ (x = 0.02, 0.06; Ln = La, Pr, Gd, Yb) solid solutions have been prepared by modified solid-state synthesis using organic-ligand precursors. The solid solutions have been characterized by thermal analysis, IR spectroscopy, x-ray powder diffraction, and atomic force microscopy. All of them have a rhombohedrally distorted perovskite structure (sp. gr. R3c).     

Properties of fluorine-doped PbMg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>O<Subscript>3</Subscript> ceramics

We report the first fluorine doping of lead magnesium niobate in the PbMg _{(1 + x)/3}Nb_{(2 ? x)/3}O_{3 ? x} F _x system in a wide composition range, x = 0.025 to 0.625. The fluorine content of the samples is shown to be substantially lower than the intended one because of the fluorine volatilization in the form of HF during synthesis and sintering in air. The ceramics consist of magnesium and lead oxides undetectable by x-ray diffraction, and a perovskite phase whose composition can be represented by the formula PbMg_{(1 + m)/3}Nb_{(2 ? m)/3}O_{3 ? m} F _m , where the fluorine content after sintering is m ≤ 0.12. The PbO and MgO contents of the ceramics depend on the starting mixture composition (x) and heat-treatment conditions (hydrogen fluoride and lead oxide volatilization). As a result of the low fluorine content, the diffraction patterns of the samples show no superlattice reflections, and their lattice parameter varies insignificantly with x. Data are presented on the temperaturedependent dielectric permittivity of ceramic samples sintered and annealed under different conditions.