Kinetics of Thermal Transformation of Mg<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript> · 8H<Subscript>2</Subscript>O to Mg<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>

The kinetics of thermal dehydration of Mg₃(PO₄)₂ · 8H₂O was investigated using thermogravimetry at four different heating rates. The activation energies of the dehydration step of Mg₃(PO₄)₂ · 8H₂O were calculated through the isoconversional Ozawa and Kissinger-Akahira-Sunose (KAS) methods and iterative methods, which were found to be consistent and indicate a single mechanism. The possible conversion function of the dehydration reaction for Mg₃(PO₄)₂ · 8H₂O has been estimated through the Coats and Redfern integral equation, and a better kinetic model such as random nucleation of the “Avrami–Erofeev equation (A _3/2 model)” was found. The thermodynamic functions (ΔH*, ΔG*, and ΔS*) of the dehydration reaction are calculated by the activated complex theory and indicate that it is a non-spontaneous process when the introduction of heat is not connected.     

Investigation of solid solution of ZrP<Subscript>2</Subscript>O<Subscript>7</Subscript>–Sr<Subscript>2</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript>

In this study, ZrP₂O₇ was synthesized by the solid state reaction of ZrO₂ and NH₄H₂PO₄ at 900 °C. Then, in set 1; 10, 5, 1, 0.5, 0.1, 0.05, 0.03% previously prepared Sr₂P₂O₇ were doped into ZrP₂O₇, and Sr₂P₂O₇ slightly affect the unit cell parameter of cubic ZrP₂O₇ (a = 8.248(6)–8.233(8) Å). The reverse of this process was also applied to Sr₂P₂O₇ system (set 2). ZrP₂O₇ changes the unit cell parameters of orthorhombic Sr₂P₂O₇ in between a = 8.909(5)–8.877(5) Å, b = 13.163(3)–13.12(1) Å, and c = 5.403(2)–5.386(4) Å. Analysis of the vibrations of the P₂O ₇ ^4? ion and approximate band assignments for IR and Raman spectra are also reported in this work. Some coincidences in infrared and Raman spectra both sets were found and strong P–O–P bands were observed. Surface morphology, EDX analysis, and thermoluminescence properties of both sets were given the first time in this paper.     

BaFe<Subscript>12</Subscript>O<Subscript>19</Subscript> films produced from BaFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/α-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> heterostructures

BaFe₁₂O₁₉ hexaferrite films have been produced on thermally oxidized single-crystal silicon (SiO₂/Si) substrates by sequential ion-beam sputtering of BaFe₂O₄ and α-Fe₂O₃ targets in an argon-oxygen atmosphere. Their crystal structure has been studied, and the origin of the impurity phases forming during heat treatment has been identified. The results show that heat treatment may lead to the formation of eutectic melts. As a result, the hexaferrite films may contain spherulites.     

Temporal Stability of Magnetization of ε-In<Subscript>0.24</Subscript>Fe<Subscript>1.76</Subscript>O<Subscript>3</Subscript> Nanoparticles

The kinetics of spontaneous demagnetization in nanoparticles of the exotic epsilon-phase of indium-doped iron(III) oxide (ε-In_0.24Fe_1.76O₃) has been studied using the method of accelerated testing of magnets for temporal stability in a magnetization-reversal field. Time dependences of the magnetization of nanoparticles measured in a wide range of magnetic fields exhibited rectification in semilogarithmic coordinates. The dependence of the magnetic viscosity on the magnetic field has been measured and used for determining the fluctuation field and activation volume. A relationship between the magnetic viscosity and magnetic noise caused by random thermoinduced magnetization reversal in separate nanoparticles is established.     

Enhanced microwave dielectric properties of Ba<Subscript>0.40</Subscript>Sr<Subscript>0.60</Subscript>TiO<Subscript>3</Subscript>–Zr<Subscript>0.80</Subscript>Sn<Subscript>0.20</Subscript>TiO<Subscript>4</Subscript> composite ceramics

The (1−x) Ba_0.40Sr_0.60TiO₃ (BST)−xZr_0.80Sn_0.20TiO₄ (ZST) composite ceramics with x = 10, 20, 30, and 40 wt% were fabricated by conventional solid-state reaction method. With increasing of ZST content, the dielectric constant of composite ceramics was decreased and dielectric loss increases. The effect of ZnO addition to 70 wt% BST–30 wt% ZST composition on the microstructure and dielectric properties was investigated. The improvements in dielectric constant, dielectric loss, and microwave dielectric properties of composite ceramics can be achieved by ZnO addition. The sample with 98 wt% (70 wt% BST–30 wt% ZST)–2 wt%ZnO composition exhibits promising dielectric properties, with dielectric constant, loss tangent and tunability at 4 kV/mm, of 125, 0.0016 and 12%, at 10 kHz and room temperature. At ~2 GHz, it possesses a dielectric constant of 101 and a Q factor of 187, which makes it a good candidate for tunable microwave device applications.     

Catalytic combustion of methane over Pt and PdO-supported CeO<Subscript>2</Subscript>–ZrO<Subscript>2</Subscript>–Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>/γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

Catalytic combustion of methane was investigated on Pt and PdO-supported CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalysts prepared by a wet impregnation method in the presence of polyvinylpyrrolidone. The catalysts were characterized by X-ray fluorescence analysis, X-ray powder diffraction, X-ray photoelectron spectra, transmission electron microscopy, and BET specific surface area measurements. The Pt/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ and PdO/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalysts were selective for the total oxidation of methane into carbon dioxide and steam, and no by-products such as HCHO, CO, and H₂ were obtained. The catalytic activities of the PdO/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalysts were relatively higher than those of the Pt-supported catalysts, due to the facile re-oxidation of metallic Pd into PdO based on lattice oxygen supplied from the CeO₂–ZrO₂–Bi₂O₃ bulk. A decrease in the calcination temperature during the preparation process was found to be effective in enhancing the specific surface area of the catalysts, whereby particle agglomeration was inhibited. Optimization of the PdO amount and calcination temperature enabled complete oxidation of methane at temperatures as low as 320 °C on the 11.6 wt% PdO/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalyst prepared at 400 °C.     

Microwave dielectric properties of temperature-stable (Mg<Subscript>0.95</Subscript>Co<Subscript>0.05</Subscript>)<Subscript>2</Subscript>TiO<Subscript>4</Subscript>–Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> composite ceramics for LTCC applications

In this paper, the effects of Li₂O–B₂O₃–Bi₂O₃–SiO₂ (LBBS) glass on the phase formation, sintering characteristic, the microstructure and microwave dielectric properties of temperature-stable (Mg_0.95Co_0.05)₂TiO₄–Li₂TiO₃ ceramics were investigated. (Mg_0.95Co_0.05)₂TiO₄–Li₂TiO₃ powders were obtained by using the traditional solid-state process. A small amount of LBBS doping can effectively reduce sintering temperature and promote the densification of the ceramics. X-ray diffraction analysis revealed not only the primary phase (Mg·Co)₂TiO₄ associated with Li₂TiO₃ minor phase but also a third phase (Mg·Co)TiO₃. The dielectric constant and Qf values vary with the doping amount of LBBS and sintering temperatures. With the compensation of the positive temperature coefficient (τ _f ) of Li₂TiO₃ and the negative τ _f of (Mg_0.95Co_0.05)₂TiO₄, the τ _f of the specimens fluctuates around zero. The (Mg_0.95Co_0.05)₂TiO₄ ceramic with 2.5 wt% LBBS addition and sintering at 900?°C for 4 h exhibited excellent microwave dielectric properties: ? _r ?=?19.076, Qf?=?126100 GHz, and τ _f ?=?0.98 ppm/°C.     

Growth of bulk β-BaB<Subscript>2</Subscript>O<Subscript>4</Subscript> crystals of high optical quality in the BaB<Subscript>2</Subscript>O<Subscript>4</Subscript>-NaBaBO<Subscript>3</Subscript> system

Phase equilibria along the BaB₂O₄-NaBaBO₃ join of the BaO-B 2 O 3 -Na 2 O system are studied by differential thermal analysis and modified visual thermal analysis. The join is shown to be suitable for growing - BaB₂O₄ crystal of high optical quality.Translated from Neorganicheskie Materialy, Vol. 41, No. 1, 2005, pp. 64–69. Original Russian Text Copyright © 2005 by Kokh, Kononova, Fedorov, Bekker, Kuznetsov.     

Growth and structure of Mg(Fe<Subscript>0.8</Subscript>Ga<Subscript>0.2</Subscript>)<Subscript>2</Subscript>O<Subscript>4 − δ</Subscript> films

Films 150–200 nm in thickness, with the nominal composition Mg(Fe_0.8Ga_0.2)₂O_{4 − δ} have been grown on (100) single-crystal silicon substrates by ion-beam sputtering in vacuum. The effect of growth and annealing conditions on the crystal structure and morphology of the films has been studied, and the thermal conditions for the growth of spinel-structure films have been optimized.     

Angular-Dependent Vortex Pinning Properties of YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>7−<Emphasis Type="Italic">δ</Emphasis></Subscript>/Y<Subscript>2</Subscript>O<Subscript>3</Subscript> Quasi-Multilayers

A series of quasi-multilayers of YBa₂Cu₃O_7?δ (YBCO)/Y₂O₃ specifically 70 × (m YBCO/n Y₂O₃) were prepared on SrTiO₃ single crystal using pulsed-laser deposition (PLD) with a controlled deposition pulses of m = 40 and n = 2, 5, and 10 for YBCO and Y₂O₃, respectively. The x-ray diffraction patterns indicate that all the present quasi-multilayers exhibit good c-axis orientation. The angular dependence of critical current density (J _c ) on applied magnetic field directions are systemically measured to study the anisotropic vortex pinning performances for those quasi-multilayers. It is revealed that compared with the pure YBCO films, the quasi-multilayers with n = 2, i.e., a proper constituent pulse of Y₂O₃, exhibits the enhanced vortex pinning abilities in all angles between c-axis orientation and the applied magnetic field direction. As well, such a quasi-multilayer film (n = 2) shows the higher lift factor J _c (Θ)/ J _c (90°) and much better vortex pinning properties at high fields and high temperatures, showing promising potential for coated conductor application.     

Effect of gamma radiation on electrical and optical properties of (TeO<Subscript>2</Subscript>)<Subscript>0·9</Subscript> (In<Subscript>2</Subscript>O<Subscript>3</Subscript>)<Subscript>0·1</Subscript> thin films

We have studied in detail the gamma radiation induced changes in the electrical properties of the (TeO₂)_0·9 (In₂O₃)_0·1 thin films of different thicknesses, prepared by thermal evaporation in vacuum. The current–voltage characteristics for the as-deposited and exposed thin films were analysed to obtain current versus dose plots at different applied voltages. These plots clearly show that the current increases quite linearly with the radiation dose over a wide range and that the range of doses is higher for the thicker films. Beyond certain dose (a quantity dependent on the film thickness), however, the current has been observed to decrease. In order to understand the dose dependence of the current, we analysed the optical absorption spectra for the as-deposited and exposed thin films to obtain the dose dependences of the optical bandgap and energy width of band tails of the localized states. The increase of the current with the gamma radiation dose may be attributed partly to the healing effect and partly to the lowering of the optical bandgap. Attempts are on to understand the decrease in the current at higher doses. Employing dose dependence of the current, some real-time gamma radiation dosimeters have been prepared, which have been found to possess sensitivity in the range 5–55 μGy/μA/cm². These values are far superior to any presently available real-time gamma radiation dosimeter.     

Crystal structure of a Np(V) sesquioxalate,Na<Subscript>4</Subscript>(NpO<Subscript>2</Subscript>)<Subscript>2</Subscript>(C<Subscript>2</Subscript>O<Subscript>4</Subscript>)<Subscript>3</Subscript>·2H<Subscript>2</Subscript>O

The crystal structure of a previously unknown Np(V) sesquioxalate, Na₄(NpO₂)₂(C₂O₄)₃·2H₂O was studied. The crystal structure consists of neptunyl(V) cations, sodium cations, oxalate anions, and water molecules of crystallization. Neptunyl(V) cations and oxalate ions form anionic chains [(NpO₂)₂(C₂O₄)₃] _n ^4n? . The coordination polyhedron (CP) of Np (pentagonal bipyramid) contains two apical “yl” oxygen atoms and five equatorial O atoms of three oxalate ions. The CP of Na(1) and Na(2) cations are combined through the common edges into zigzag chains in the [010] direction. Two independent oxalate ions are tridentate and tetradentate ligands.     

Variable—Range hopping in Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-K<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript> glasses

The dc conductivity of the glasses in the Fe₂O₃-Bi₂O₃-K₂B₄O₇ system was studied at temperatures between 223 and 393 K. At temperatures from 300 to 223 K, T^–1/4 (T is temperature) dependence of the conductivity was found, however, both Mott variable-range hopping and Greaves intermediate range hopping models are found to be applicable. Mott and Greaves parameters analysis gave the density of states at Fermi level N (E_F) = 3.13 × 10²⁰–21.01 × 10²⁰ and 1.93 × 10²¹–16.39 × 10²¹ cm^–3eV^–1 at 240 K, respectively. The variable-range hopping conduction occurred in the temperature range T = 300–223 K, since W_D was found to be large (W_D = 0.08–0.14 eV for these glasses) and dominated the conduction at T < 300 K.     

A physicochemical study of the Sb<Subscript>2</Subscript>Se<Subscript>3</Subscript>–Nd<Subscript>2</Subscript>Se<Subscript>3</Subscript> system

We have studied phase relations in the Sb₂Se₃–Nd₂Se₃ system and mapped out its T–x phase diagram using differential thermal analysis, X-ray diffraction, microstructural analysis, microhardness tests, and density measurements. The system contains one compound, with the composition NdSbSe₃, which melts incongruently at 865 K and crystallizes in orthorhombic symmetry with the following lattice parameters: а = 12.77(1) Å, b = 14.08(1) Å, and c = 5.82(5) Å (Z = 8, ρ_meas = 6.20 g/cm³, ρ_x = 6.38 g/cm³). At room temperature, the Nd₂Se₃ solubility in Sb₂Se₃ is 5 mol % and the Sb₂Se₃ solubility in Nd₂Se₃ is 2.5 mol %. The Sb₂Se₃–Nd₂Se₃ system has a eutectic located at 15 mol % Nd₂Se₃, with a melting point at 755 K. The electrical conductivity and thermoelectric power of the (Sb₂Se₃)_1–x (Nd₂Se₃) _x solid solutions have been measured as functions of temperature.     

Dual relaxation behaviors and large electrostrictive properties of Bi<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript>–Sr<Subscript>0.85</Subscript>Bi<Subscript>0.1</Subscript>TiO<Subscript>3</Subscript> ceramics

Lead-free ceramics (1???x)Bi_0.5Na_0.5TiO₃–xSr_0.85Bi_0.1TiO₃ (BNT–xSBT, x?=?0.4, 0.5, 0.6 and 0.7) were prepared by a solid-state reaction process. Coexistence of ferroelectric relaxation at low temperature and Maxwell–Wagner dielectric relaxation at high temperature was revealed for the first time in this system. Meanwhile, hysteresis-free P–E loops combined with a very high piezoelectric strain coefficient (d₃₃) of 1658 pC/N concurrently with large electrostrictive coefficient Q?=?0.287 m⁴C^?2 were achieved. The ferroelectric relaxor behavior and large electrostrictive strain might be linked to easy reorientation and reversal of ergodic PNRs and the combined effect of Bi off-center position and lone pair electrons.     

Spectroscopic characterisation of local structure in Y<Subscript>2</Subscript>O<Subscript>3</Subscript>–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses doped with gadolinium

Gadolinium doped bismuth borate glasses containing up to 30 mol% Y₂O₃ were prepared by fast melt quenching method. The effect of yttrium on the local order in 3B₂O₃ · Bi₂O₃ and B₂O₃ · Bi₂O₃ glass matrices, particularly on the bismuth sites, was investigated by infrared (IR) spectroscopy and electron paramagnetic resonance (EPR) of Gd³⁺ ions. The IR results show that the local structure is more ordered in the glass system with higher bismuth content and the progressive addition of yttrium increases the local disorder in both bismuth–borate glass matrices. The EPR results indicate that Gd³⁺ ions occupy both bismuth and yttrium sites and reflect the same structural disorder like that suggested by IR results.     

Microstructure and properties of the Ba<Subscript>0.75−x</Subscript>Ca<Subscript>x</Subscript>La<Subscript>0.25</Subscript>Fe<Subscript>11.6</Subscript>Co<Subscript>0.25</Subscript>Ti<Subscript>0.15</Subscript>O<Subscript>19</Subscript> hexaferrites

In the case of Ti⁴⁺ remain unchanged, the Ca²⁺ substituted Ba_0.75?xCa_xLa_0.25Fe_11.6Co_0.25Ti_0.15O₁₉ (0?≤?x?≤?0.05) were prepared by conventional solid-state reaction method at temperature of 1280 °C. A ball-to-power weight ratio of 10:1. Their crystal structure and magnetic properties were mainly investigated. The results show that the single magnetoplumbite phase structure transformed into the multiphase structure. Meanwhile, the small amount of α-Fe₂O₃ phase existed in M-type phase. The micrographs were observed by a field emission scanning electron microscopy (SEM). Vibrating sample magnetometer (VSM) was used to analyze the magnetic properties. The saturation magnetization (M _s ) first increases then decreases when x from 0 to 0.03. But, when x from 0.03 to 0.05, the saturation magnetization (M _s ) first increases then decreases too. The maximum value is at x?=?0.04 (M _s ?=?70.73 emu/g). The value of coercivity (H _c ) first increases then decreases when x from 0 to 0.04. But, the value increased when x from 0.04 to 0.05. The maximum value is at x?=?0.02 (H _c ?=?1691 Oe).     

Influence of Bi substitution on microwave dielectric properties of BaO–La<Subscript>2</Subscript>O<Subscript>3</Subscript>–Sm<Subscript>2</Subscript>O<Subscript>3</Subscript>–TiO<Subscript>2</Subscript> ceramics

The influences of Bi substitution on microwave dielectric properties of Ba₄(La_0.5Sm_0.5)_9.33Ti₁₈O₅₄ solid solutions were investigated. Dielectric ceramics with general formula Ba₄(La_(0.5−z)Sm_0.5Bi _z )_9.33Ti₁₈O₅₄, z = 0.0–0.2 were prepared by conventional solid state route. The structural analysis of all the samples was carried out by X-ray diffraction and scanning electron microscopy. The dielectric properties were investigated as a function of Bi contents using open-ended coaxial probe method in the frequency range 0.3–3.0 GHz at room temperature. Dielectric constant varies from 83 to 88 and loss tangent from 2.1 × 10⁻³ to 5.5 × 10⁻³ at 3 GHz with temperature coefficient of resonant frequency changing from 106.7 to −8.4 ppm/oC as Bi contents increases from z = 0.00–0.20. It has been found that dielectric constant and temperature coefficient of resonant frequency improve whereas loss tangent is adversely affected with increase in Bi substitution.     

Effect of excess Pb in PbTiO<Subscript>3</Subscript> precursors on ferroelectric and fatigue property of sol–gel derived PbTiO<Subscript>3</Subscript>/PbZr<Subscript>0.3</Subscript>Ti<Subscript>0.7</Subscript>O<Subscript>3</Subscript>/PbTiO<Subscript>3</Subscript> thin films

A series of Pb_(1+x)TiO₃/PbZr_0.3Ti_0.7O₃/Pb_(1+x)TiO₃ (PTO/PZT/PTO) and PbZr_0.3Ti_0.7O₃ (PZT) thin films were prepared by a sol–gel method. Different excess Pb content (x) (x = 0, 0.05, 0.10, 0.15, 0.20) were added to the PbTiO₃ (PTO) precursors to investigate their effect on ferroelectric and fatigue properties of the PTO/PZT/PTO thin films. X-ray diffraction results show that the crystallization behavior of the PTO/PZT/PTO thin films is greatly affected by the excess Pb content (x) in PTO precursors. Topographic images show that the PTO/PZT/PTO thin films with excess Pb content x = 0.10 appears the densest and the most uniform grain size surface morphology. The ferroelectric and fatigue properties of the films correlate straightforwardly to the crystallization behaviors and excess Pb content (x) in the PTO precursors. The excess Pb content (x) in the PTO layers which acts as a nucleation site or seeding layer for PZT films affects the crystallization of the PTO layer and ultimately affects the perovskite phase formation of the PZT films. With the proper excess Pb content (x = 0.10–0.15) in the PTO precursors, the pure perovskite structure PTO/PZT/PTO thin films, with dense, void-free, and uniform fine grain size are obtained, and a well-saturated hysteresis loop with higher remnant polarization is achieved. Using an appropriate Pb content, the fatigue has been avoided by controlling the inter-diffusion and surface volatilization.     

Probe Mössbauer Spectroscopy of BiNi<Subscript>0.96</Subscript><Superscript>57</Superscript>Fe<Subscript>0.04</Subscript>O<Subscript>3</Subscript>

This paper presents results of a ⁵⁷Fe probe Mössbauer spectroscopy study of the BiNi_0.96⁵⁷Fe_0.04O₃ nickelate. The spectra measured above its TN demonstrate that Fe³⁺ cations heterovalently substitute for Ni²⁺ nickel (←Fe³⁺), being stabilized on four sites of the nickel sublattice in the structure of BiNiO₃. Calculations in an ionic model with allowance for monopole and dipole contributions to the electric field gradient indicate that the parameters of electric hyperfine interactions between ⁵⁷Fe probe atom nuclei reflect the specifics of the local environment of the nickel in the structure of the unsubstituted BiNiO₃ nickelate. Below T^N, Mössbauer spectra transform into a complex Zeeman structure, which is analyzed in terms of first-order perturbation theory with allowance for electric quadrupole interactions as a small perturbation of the Zeeman levels of the ⁵⁷Fe hyperfine structure, as well as for specific features of the magnetic ordering of the Ni²⁺ cations in the nickelate studied.