Separation characteristics of tetrapropylammoniumbromide templating silica/alumina composite membrane in CO<Subscript>2</Subscript>/N<Subscript>2</Subscript>, CO<Subscript>2</Subscript>/H<Subscript>2</Subscript> and CH<Subscript>4</Subscript>/H<Subscript>2</Subscript> systems

Nanoporous silica membrane without any pinholes and cracks was synthesized by organic templating method. The tetrapropylammoniumbromide (TPABr)-templating silica sols were coated on tubular alumina composite support ( γ-Al₂O₃/ α-Al₂O₃ composite) by dip coating and then heat-treated at 550 °C. By using the prepared TPABr templating silica/alumina composite membrane, adsorption and membrane transport experiments were performed on the CO₂/N₂, CO₂/H₂ and CH₄/H₂ systems. Adsorption and permeation by using single gas and binary mixtures were measured in order to examine the transport mechanism in the membrane. In the single gas systems, adsorption characteristics on the α-Al₂O₃ support and nanoporous unsupport (TPABr templating SiO₂/ γ-Al₂O₃ composite layer without α-Al₂O₃ support) were investigated at 20–40 °C conditions and 0.0–1.0 atm pressure range. The experimental adsorption equilibrium was well fitted with Langmuir or/and Langmuir-Freundlich isotherm models. The α-Al₂O₃ support had a little adsorption capacity compared to the unsupport which had relatively larger adsorption capacity for CO₂ and CH₄. While the adsorption rates in the unsupport showed in the order of H₂> CO₂> N₂> CH₄ at low pressure range, the permeate flux in the membrane was in the order of H₂≫N₂> CH₄> CO₂. Separation properties of the unsupport could be confirmed by the separation experiments of adsorbable/non-adsorbable mixed gases, such as CO₂/H₂ and CH₄/H₂ systems. Although light and non-adsorbable molecules, such as H₂, showed the highest permeation in the single gas permeate experiments, heavier and strongly adsorbable molecules, such as CO₂ and CH₄, showed a higher separation factor (CO₂/H₂=5-7, CH₄/H₂=4-9). These results might be caused by the surface diffusion or/and blocking effects of adsorbed molecules in the unsupport. And these results could be explained by surface diffusion. This paper is dedicated to Professor Hyun-Ku Rhee on the occasion of his retirement from Seoul National University.     

Low-temperature anti-icing reagents in the Ca(NO<Subscript>3</Subscript>)<Subscript>2</Subscript>-Mg(NO<Subscript>3</Subscript>)<Subscript>2</Subscript>-CO(NH<Subscript>2</Subscript>)<Subscript>2</Subscript>-H<Subscript>2</Subscript>O system and their properties

The polytherms of ice melting in sections of the Ca(NO₃)₂-Mg(NO₃)₂-CO(NH₂)₂-H₂O system with different component ratios were studied in the temperature interval from 0 to −40°C. A series of nitrate and nitrate-carbonate reagents that are promising for the creation of anti-acing reagents were found, which form eutectics with ice at temperatures from −25 to −39°C. Their properties, viz., melting properties with respect to ice and corrosiveness on metals and alloys, were determined. An effective corrosion inhibitor was selected.     

Photoreduction of CO<Subscript>2</Subscript> into CH<Subscript>4</Subscript> using Bi<Subscript>2</Subscript>S<Subscript>3</Subscript>-TiO<Subscript>2</Subscript> double-layered dense films

Nano-sized bismuth sulfide (Bi₂S₃) and titanium dioxide (TiO₂) with the orthorhombic and anatase tetragonal structures, respectively, were synthesized for application as catalysts for the reduction of carbon dioxide (CO₂) to methane (CH₄). Four double-layered dense films were fabricated with different coating sequences—TiO₂ (bottom layer)/Bi₂S₃ (top layer), Bi₂S₃/TiO₂, TiO₂/Bi₂S₃: TiO₂ (1 : 1) mix, and Bi₂S₃: TiO₂ (1 : 1) mix/Bi₂S₃: TiO₂ (1 : 1) mix—and applied to the photoreduction of CO₂ to CH₄; the catalytic activity of the fabricated films was compared to that of the pure TiO₂/TiO₂ and Bi₂S₃/Bi₂S₃ doubled-layered films. The TiO₂/Bi₂S₃ double-layered film exhibited superior photocatalytic behavior, and higher CH₄ production was obtained with the TiO₂/Bi₂S₃ double-layered film than with the other films. A model of the mechanism underlying the enhanced photoactivity of the TiO₂/Bi₂S₃ double-layered film was proposed, and it was attributed in effective charge separation.     

Synthetic spinels of the system MgO-Cr<Subscript>2</Subscript>O<Subscript>3</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>

Synthetic spinels of the system MgO-Cr₂O₃-Al₂O₃-Fe₂O₃ are considered and the desirability of organizing their production for the refractory industry is demonstrated. Translated from Novye Ogneupory, No. 6, pp. 32–35, June 2008.     

Electrical conductivity and structure of glasses in the Na<Subscript>2</Subscript>O-Na<Subscript>2</Subscript>S-P<Subscript>2</Subscript>O<Subscript>5</Subscript> and Na<Subscript>2</Subscript>S-P<Subscript>2</Subscript>S<Subscript>5</Subscript> systems

The glasses, in which oxygen was partially replaced with sulfur, have been synthesized in the Na₂O-P₂O₅-Na₂S system. The chemical and chromatographic analyses of the glasses synthesized have been performed. The temperature-concentration dependences of electrical conductivity of the glasses have been studied over a wide temperature range; the glass transition temperatures and the nature of charge carriers have been determined. The IR spectra and Raman spectra have been recorded at room temperature; the density and microhardness of the glasses and ultrasound velocity have been measured. A comparison of the electrical conductivities of the investigated glasses with those of the earlier studied glasses in the Na₂O-P₂O₅ system has shown their fair coincidence. The introduction of sodium sulfide into the Na₂O-P₂O₅ system is accompanied by an approximately threefold increase in electrical conductivity, although the concentrations of charge carriers (sodium ions) in the glasses amount to ∼17 and ∼26 mmol/cm³, respectively. The rise in electrical conductivity has been assumed to be caused by the increase in the degree of dissociation of polar structural chemical units including sulfide ions and by the higher mobility of sodium ions in the oxygen-free matrix.     

Li<Subscript>2</Subscript>Cu<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> + SiO<Subscript>2</Subscript>/Ti compositions for the catalytic afterburning of diesel soot

Two methods were used to obtain a catalytically active oxide coating on the surface of titanium for the catalytic afterburning of diesel soot: plasma electrochemical formation of an oxide film on the surface of titanium and extraction pyrolytic deposition of the Li₂Cu₂(MoO₄)₃ compound. The Li₂Cu₂(MoO₄)₃/TiO₂ + SiO₂/Ti compositions synthesized by the single-step extraction pyrolytic treatment of the oxidized surface of titanium ensured a high burning rate of soot of ∼300°C. The subsequent deposition of Li₂Cu₂(MoO₄)₃ lowers the activity of the catalyst, due probably to the growth of molybdate phase crystallites and the filling of open oxide film pores. Double lithium-copper molybdate is able to reduce appreciably the concentration of CO in the oxidation products of soot. The advantages of these methods are the possibility of forming high-cohesion durable coatings on surfaces of any complexity, the simplicity of their implementation, and high productivity and low cost. The obtained results can be recommended for use in developing methods for creating composite coatings on catalytic soot filters.     

CeO<Subscript>2</Subscript>-La<Subscript>2</Subscript>O<Subscript>3</Subscript>/ZSM-5 sorbents for high-temperature H<Subscript>2</Subscript>S removal

Performance of CeO₂-La₂O₃/ZSM-5 sorbents for sulfur removal was examined at temperature ranging from 500 oC to 700 oC. The sulfur capacity of 5Ce5La/ZSM-5 was much bigger than that of CeO₂/ZSM-5. H₂ had a negative impact on the sulfidation; however, CO had little influence on sulfur removal. The characterization results showed that CeO₂ and La₂O₃ were well dispersed on ZSM-5 because of the intimate admixing of La₂O₃ and CeO₂, the major sulfidation products were Ce₂O₂S and La₂O₂S, the XRD and SEM results revealed that ZSM-5 structure could remain intact during preparation and sulfidation process, the H₂-TPR showed that the reducibility of CeO₂ can be remarkably enhanced by addition of La.     

Crystal structure of new compound (Rb,K)<Subscript>2</Subscript>Cu<Subscript>3</Subscript>(P<Subscript>2</Subscript>O<Subscript>7</Subscript>)<Subscript>2</Subscript>

A new compound of (Rb,K)₂Cu₃(P₂O₇)₂ is obtained by high-temperature reactions from a mixture of RbNO₃, KNO₃, Cu(NO₃)₂, and (NH₄)₄P₂O₇. The crystal structure was solved by direct methods and refined to R ₁ = 0.056 for 5022 independent reflections. The compound belongs to a rhombic crystal system, P2₁2₁2₁, Z = 8, a = 9.9410(7) Å, b = 13.4754(6) Å, c = 18.6353 (3) Å, and R = 0.056. The basis of the structure is a complex copper-phosphate skeleton of the composition of [Cu₃(P₂O₇)₂]^2–, which can be regarded as consisting of two types of heteropolyhedral layers parallel to the (001) plane. The layers are alternated with each other, forming a frame, in the cavities of which the positions of alkali cations are located, statistically populated with K⁺ and Rb⁺ ions. Based on the refined populations of the positions of alkali cations, an exact chemical formula of the compound can be written as Rb_1.28K_0.72Cu₃(P₂O₇)₂. The compound is the most complex among those known to this day of the composition of A₂ ^IB₃ ^II(P₂O₇)₂ (A = Li, Na, K, Rb, or Cs; B = Ni, Cu, or Zn).     

Optical Properties of CeO<Subscript>2</Subscript> Doped SiO<Subscript>2</Subscript>-Na<Subscript>2</Subscript>O-CaO-P<Subscript>2</Subscript>O<Subscript>5</Subscript> Glasses

Cerium oxide is one of the most important rare earth elements that is introduced into glass compositions due to its great effects on the optical properties. CeO₂ was introduced in Hench’s patented SiO₂-Na₂O-CaO-P₂O₅ glasses with different concentrations in order to study its effect on the optical behavior of this glass including optical band gap, transmittance, reflectance and refractive index and to give a complete view for the optical properties on cerium oxide-doped silicate glasses.     

Phase Equilibria in the Gd<Subscript>2</Subscript>O<Subscript>3</Subscript>-SrAl<Subscript>2</Subscript>O<Subscript>4</Subscript> System

The phase equilibria are investigated and the phase diagram is constructed for the Gd₂O₃-SrAl₂O₄ pseudobinary join of the Gd₂O₃-SrO-Al₂O₃ ternary oxide system. One ternary compound, namely, Gd₂SrAl₂O₇, is revealed in the Gd₂O₃-SrAl₂O₄ join. It is found that this compound undergoes congruent melting.     

Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and CeO<Subscript>2</Subscript>-promoted MgO sorbents for CO<Subscript>2</Subscript> capture at moderate temperatures

A series of Al₂O₃ and CeO₂ modified MgO sorbents was prepared and studied for CO₂ sorption at moderate temperatures. The CO₂ sorption capacity of MgO was enhanced with the addition of either Al₂O₃ or CeO₂. Over Al₂O₃-MgO sorbents, the best capacity of 24.6 mg- CO₂/g-sorbent was attained at 100 °C, which was 61% higher than that of MgO (15.3 mg-CO₂/g-sorbent). The highest capacity of 35.3 mg-CO₂/g-sorbent was obtained over the CeO₂-MgO sorbents at the optimal temperature of 200 °C. Combining with the characterization results, we conclude that the promotion effect on CO₂ sorption with the addition of Al₂O₃ and CeO₂ can be attributed to the increased surface area with reduced MgO crystallite size. Moreover, the addition of CeO₂ increased the basicity of MgO phase, resulting in more increase in the CO₂ capacity than Al₂O₃ promoter. Both the Al₂O₃-MgO and CeO₂-MgO sorbents exhibited better cyclic stability than MgO over the course of fifteen CO₂ sorption-desorption cycles. Compared to Al₂O₃, CeO₂ is more effective for promoting the CO₂ capacity of MgO. To enhance the CO₂ capacity of MgO sorbent, increasing the basicity is more effective than the increase in the surface area.

Open image in new window

     

Formation of La<Subscript>2</Subscript>Ti<Subscript>2</Subscript>O<Subscript>7</Subscript> crystals from amorphous La<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript> powders synthesized by the polymerized complex method

Amorphous La₂O-TiO₂ powders were synthesized by the polymerized complex (PC) method. The activation energies for crystallization and grain growth of La₂Ti₂O₇ from these precursors were determined from results of XRD and DTA and compared with those for La₂Ti₂O₇ precursors by the conventional solid-state reaction (SSR). Activation energy of grain growth of La₂Ti₂O₇ in PC-sample was determined to be 7.1 kJ/mol while that of SSR sample was 14.8 kJ/mol. The energy required for the phase transformation from amorphous PC sample to layered perovskite was 432 kJ/mol, while the SSR sample did not show this transition below 900‡C. It was clearly demonstrated that the La₂Ti₂O₇ crystals were formed at a lower temperature and they grew in size faster in the sample prepared by the PC method relative to the sample prepared by the SSR method. Mixing of elements in molecular level in PC preparation appeared responsible for these differences.     

Structure and crystallization of ZnO-B<Subscript>2</Subscript>O<Subscript>3</Subscript>-P<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

Structure and crystalline behavior of the ternary system ZnO-B₂O₃-P₂O₅ glasses were investigated by means of X-ray diffraction (XRD) and infrared Raman spectra. The research showed that number of the planar [BO₃] units increases with the increase of B₂O₃ content. When the B₂O₃ content is above ≥10 mol %, the relative content of planar [BO₃] units increases rapidly and causes weakening of the glass structure and decrease in the chemical stability. In the crystallized glasses the predominant crystal phase Zn₂P₂O₇ decreases with the increase of B₂O₃ content, while the crystal phase BPO₄ increases with it, which cause the declining of chemical stability and the decrease of thermal coefficients of expansion.     

Structure of an atmospheric-pressure H<Subscript>2</Subscript>/O<Subscript>2</Subscript>/N<Subscript>2</Subscript> flame doped with iron pentacarbonyl

This paper presents the measurement and simulation data on the thermal and chemical structure of an atmospheric-pressure premixed H₂/O₂/N₂ flame doped with iron pentacarbonyl Fe(CO)₅. Soft ionization molecular beam mass spectrometry was used to measure concentration profiles of the combustion products of iron pentacarbonyl: Fe, FeO₂, FeOH, and Fe(OH)₂. A comparison of experimental and simulated concentration profiles showed that they are in satisfactory agreement for FeO₂ and Fe(OH)₂ and differ significantly for Fe and FeOH. Thus, the previously proposed kinetic model for the oxidation of iron pentacarbonyl was tested and it was shown that the mechanism needs further elaboration.     

Phase cooperation of V<Subscript>2</Subscript>O<Subscript>5</Subscript> and Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> in the selective oxidation of H<Subscript>2</Subscript>S containing ammonia and water

The selective oxidation of hydrogen sulfide containing excess water and ammonia was studied over vanadium oxide-based catalysts. The investigation was focused on the role of V₂O₅, and phase cooperation between V₂O₅ and Bi₂O₃ in this reaction. The conversion of H₂S continued to decrease since V₂O₅ was gradually reduced by treatment with H₂S. The activity of V₂O₅ was recovered by contact with oxygen. A strong synergistic phenomenon in catalytic activity was observed for the mechanically mixed catalysts of V₂O₅ and Bi₂O₃. Temperature-programmed reduction (TPR) and oxidation (TPO) and two bed reaction tests were performed to explain this synergistic effect by the reoxidation ability of Bi₂O₃. This paper is dedicated to Professor Wha Young Lee on the occasion of his retirement from Seoul National University.     

Electronic and magnetic properties of SnO<Subscript>2</Subscript>/CrO<Subscript>2</Subscript> thin superlattices

In this article, using first-principles electronic structure calculations within the spin density functional theory, alternated magnetic and non-magnetic layers of rutile-CrO₂ and rutile-SnO₂ respectively, in a (CrO₂) _n (SnO₂) _n superlattice (SL) configuration, with n being the number of monolayers which are considered equal to 1, 2, ..., 10 are studied. A half-metallic behavior is observed for the (CrO₂) _n (SnO₂) _n SLs for all values of n. The ground state is found to be FM with a magnetic moment of 2 μ_B per chromium atom, and this result does not depend on the number of monolayers n. As the FM rutile-CrO₂ is unstable at ambient temperature, and known to be stabilized when on top of SnO₂, the authors suggest that (CrO₂) _n (SnO₂) _n SLs may be applied to spintronic technologies since they provide efficient spin-polarized carriers.     

Structure and electrical conductivity of glasses in the Na<Subscript>2</Subscript>O-Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>-P<Subscript>2</Subscript>O<Subscript>5</Subscript> system

The temperature-concentration dependence of the electrical conductivity of glasses in the Na₂SO₄-NaPO₃ and Na₂O-P₂O₅ systems has been investigated. Based on the obtained experimental data (IR spectra, density, microhardness, sound velocity, and paper chromatography), it has been demonstrated that SO₄²⁻ ions form terminal groups through the incorporation into polyphosphate fragments of the structure of glasses in the Na₂SO₄-NaPO₃ system. An increase in the electrical conductivity of glasses in this system by a factor of ∼1000 (as compared to NaPO₃) at 25°C and a decrease in the activation energy for electrical conduction from 1.40 to 1.10 eV have been interpreted from the viewpoint of the decrease in the dissociation energy E _d of polar sulfate phosphate structural chemical fragments formed in the glass bulk upon introduction into sodium metaphosphate Na₂SO₄. This leads to an increase in the number of dissociated sodium ions, which are charge carriers, and to a decrease in the energy (E _a) of their activation shift in the sublattice formed by sulfate phosphate fragments of the structure.     

Ni<Superscript>2+</Superscript> reduction under solar irradiation over CuFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/TiO<Subscript>2</Subscript> catalysts

The photo-electrochemical characterization of the hetero-system CoFe₂O₄/TiO₂ was undertaken for the Ni²⁺ reduction under solar light. The spinel CoFe₂O₄ was prepared by nitrate route at 940 °C and the optical gap (1.66 eV) was well matched to the sun spectrum. The flat band potential (-0.21 V_SCE) is more cathodic than the potential of Ni²⁺/Ni couple (-0.6 V_SCE), thus leading to a feasible nickel photoreduction. TiO₂ with a gap of 3.2 eV is used to mediate the electrons transfer. The reaction is achieved in batch configuration and is optimized with respect to Ni²⁺ concentration (30 ppm); a reduction percentage of 72% is obtained under sunlight, the Ni²⁺ reduction is strongly enhanced and follows a first order kinetic with a rate constant of 4.6×10^-2 min^-1 according to the Langmuir-Hinshelwood model.     

Phase equilibria in the Ho<Subscript>2</Subscript>O<Subscript>3</Subscript>-SrAl<Subscript>2</Subscript>O<Subscript>4</Subscript> system

The phase formation is investigated and the phase diagram of the Ho₂O₃-SrAl₂O₄ system is constructed. A ternary compound, namely, Ho₂SrAl₂O₇, is revealed. It is established that this compound undergoes incongruent melting.     

Comparative study of the preparation and electrochemical performance of LiNi<Subscript>1</Subscript><Subscript>/2</Subscript>Mn<Subscript>1/2</Subscript>O<Subscript>2</Subscript> electrode material for rechargeable lithium batteries

Positive electrode material LiNi_1/2Mn_1/2O₂ was synthesized via the carbonate co-precipitation method and the hydroxide precipitation route to study the effects of the precursor on its structural and electrochemical properties. The results of X-ray diffraction and Rietveld refinement show that the carbonate precursor of Ni²⁺ and Mn²⁺ exhibits one phase at a pH of 8.5, while the hydroxide deposit separates into Ni(OH)₂ and Mn(OH)₂ phases under the same experimental conditions. LiNi_1/2Mn_1/2O₂ material prepared from the hydroxide precursor shows 8.9% Li/Ni exchange and a large capacity loss of 11.3% in the first 10 cycles. By contrast, more uniform distribution of transition metal ions and stable Mn²⁺ in the carbonate precursor contribute to only 7.8% Li/Ni disorder in the obtained LiNi_1/2Mn_1/2O₂, which delivers a reversible capacity of about 182 mAh g⁻¹ at a current rate of 14 mA g⁻¹ between 2.5 and 4.8 V.