Ni3Al Matrix Composite with Lubricious Tungstate at High Temperatures

Ni₃Al–Ag–BaF₂/CaF₂–W composites were fabricated by the powder metallurgy route, and their tribological properties over a wide temperature range, starting from room temperature up to 800 °C, were investigated. The Ni₃Al matrix composite with 15 wt% BaF₂/CaF₂ exhibited a favorable friction coefficient (range 0.3–0.4) and wear rate (0.2–6.2 × 10⁻⁴mm³ N⁻¹ m⁻¹). The formation of BaWO₄ and CaWO₄ with lubricity on the worn surface due to a tribo-chemical reaction at high temperatures provided excellent lubricating properties. The low friction coefficient over a broad temperature range could be attributed to the synergistic effect of Ag, BaF₂/CaF₂, BaWO₄, and CaWO₄.     

Tribological Property of Ni<Subscript>3</Subscript>Al Matrix Composites with Addition of BaMoO<Subscript>4</Subscript>

The Ni₃Al matrix composites with addition of 10, 15, and 20 wt% BaMoO₄ were fabricated by powder metallurgy technique, and the tribological behaviors were studied from room temperature to 800 °C. It was found that BaAl₂O₄ formed during the fabrication process. The Ni₃Al composites showed poor tribological property below 400 °C, with high friction coefficients (above 0.6) and wear rates (above 10⁻⁴ mm³/Nm). However, the composites exhibited excellent self-lubricating and anti-wear properties at higher temperatures, and the composite with addition of 15 wt% BaMoO₄ had the lowest wear rate (1.10 × 10⁻⁵ mm³/Nm) and friction coefficient (0.26). In addition, the results also indicated that BaAl₂O₄ for the Ni₃Al composites did not exhibit lubricating property from room temperature to 800 °C.     

NiAl Matrix High-Temperature Self-Lubricating Composite

A high-temperature self-lubricating composite NiAl–Cr–Mo–CaF₂ was fabricated using the powder metallurgy technique, and the tribological behavior of the composite at a wide range of temperatures (room temperature to 1000 °C) was investigated. The results showed that the composite had a favorable friction coefficient of about 0.2 and an excellent wear resistance of about 1 × 10⁻⁵ mm³N⁻¹m⁻¹ at the high temperatures tested (800 and 1000 °C). The excellent self-lubricating performance was attributed to the formation of the glaze film on the worn surface consisting mainly of CaCrO₄ and CaMoO₄ as high-temperature solid lubricants.     

Effect of Applied Load and Surface Roughness on the Tribological Properties of Ni-Based Superalloys Versus Ta<Subscript>2</Subscript>AlC/Ag or Cr<Subscript>2</Subscript>AlC/Ag Composites

The novel Ta₂AlC–20 vol.% Ag (TaAg) and Cr₂AlC–20 vol.% Ag (CrAg) composites were tribologically tested versus a Ni-based superalloy Inc718 (SA) by dry sliding at a sliding speed of 1 m/s at room temperature in air at loads from 3 N to 18 N. The TaAg composites were also tested at 8 and 18 N at 550 °C, and at a 3 N load against the SA with different surface roughnesses at 26 °C and 550 °C. At room temperatures, the coefficients of friction, μ’s, decreased from ~0.8–0.9 to ~0.3–0.4 for both the TaAg and CrAg composites as the applied normal force increased from 3 N to 8 N. Further increases in load to 18 N did not change the μ’s. The specific wear rates, sWR, increased with increased loads for the TaAg composite; they remained almost unchanged for the CrAg composite. This behavior was attributed to the formation of glaze tribofilms—similar to ones observed previously in these tribocouples at elevated temperatures and 3 N—promoted by the increased loads. Preconditioning of the SA surface by sliding against the TaAg composite at 550 °C and 8 N resulted in μ’s of <0.2 and sWR < 10⁻⁶ mm³/N-m in subsequent room temperature sliding at 3 N. Somewhat higher, but stable room temperature μ’s of ~0.3 and sWR of ~3 × 10⁻⁵ mm³/N-m were observed when the TaAg composites were slid versus a sandblasted SA surface at 500 °C and 3 N. It follows that in situ preconditioning of the tribo-surfaces is a powerful tool for improving the properties of the MAX/Ag-SA tribocouples. The relationship between sliding conditions, chemistries of tribofilms, and their properties are discussed.     

Tribological behaviors and mechanisms of Ti<Subscript>3</Subscript>AlC<Subscript>2</Subscript>

Tribological behaviors and the relevant mechanism of a highly pure polycrystalline bulk Ti₃AlC₂ sliding dryly against a low carbon steel disk were investigated. The tribological tests were carried out using a block-on-disk type high-speed friction tester, at the sliding speeds of 20–60 m/s under a normal pressure of 0.8 MPa. The results showed that the friction coefficient is as low as 0.1∼0.14 and the wear rate of Ti₃AlC₂ is only (2.3–2.5) × 10⁻⁶ mm³/Nm in the sliding speed range of 20–60 m/s. Such unusual friction and wear properties were confirmed to be dependant dominantly upon the presence of a frictional oxide film consisting of amorphous Ti, Al, and Fe oxides on the friction surfaces. The oxide film is in a fused state during the sliding friction at a fused temperature of 238–324 °C, so it takes a significant self-lubricating effect.     

High Temperature Tribological Characteristics of Fe–Mo-based Self-Lubricating Composites

Fe–Mo-based self-lubricating composites were prepared by a powder metallurgical hot-pressing method. The tribological properties of Fe–Mo-based composites with varied CaF₂ contents at high temperature were evaluated, and the effect of glaze films on the friction and wear characteristics of composites were analyzed. The results show that the introduction of CaF₂ into Fe–Mo alloys improved the mechanical properties, and the best tribological properties of Fe–Mo–CaF₂ composites were achieved at the CaF₂ content of 8 wt% at both room temperature and 600 °C. The worn surface of Fe–Mo–CaF₂ composite at 600 °C is characterized to plastic deformation and slight scuffing, and the improved tribological properties are attributed to the formation of lubricious glaze film that composed of high-temperature lubricants CaMoO₄ and CaF₂ on the worn surface of the composites.     

The Tribological Behaviour of Fe–28Al–5Cr/TiC Under Liquid Paraffine Lubrication

The tribological behaviour of Fe–28Al–5Cr and its composites containing 15, 25 and 50 wt% TiC (corresponding to 19.3, 31.2 and 57.6 vol%), produced by hot-pressing process, was investigated under liquid paraffine lubrication against an AISI 52100 steel ball in ambient environment at varied applied loads and sliding speeds. It was found that the wear resistance increased and friction coefficient decreased with increasing of TiC content. The coefficients of friction are in the range of 0.09–0.14 at the given testing conditions. The wear rates of all the materials except the 50% composite are on the order of 10⁻⁶–10⁻⁵ mm³ m⁻¹, the wear rate for the 50% composite is too low to quantify under the two sliding conditions, (50 N, 0.04 m/s) and (100 N, 0.02 m/s). The wear rates of all the materials increase as applied load increases and the increasing extent diminishes with the increase of TiC content, but first increase slightly and then nearly remains steadiness with increasing sliding speed. The 50 wt% composite has wear resistance about 7–20 times better than pure Fe–28Al–5Cr at different sliding parameters. The enhanced wear resistance by TiC addition is attributed to the high hardness of the composites, as well as support of the oil lubrication film/layer by the hard TiC phase. The worn surfaces of all the materials are analyzed by a scanning electron microscope. The dominant wear mechanism of the Fe–28Al–5Cr and 15% composite is grooving and flaking-off, but those of the 25 and 50% composites are mainly shallow grooving.     

Reciprocating Sliding Friction and Wear Property of Fe<Subscript>3</Subscript>Si Based Alloys Containing Cu in Water Lubrication

Fe₃Si, Fe₃Si alloys containing Cu were fabricated by arc melting followed by hot-pressing. The friction and wear behaviors of Fe₃Si based alloys with and without Cu addition against Si₃N₄ ball in water-lubrication were investigated. The friction coefficient and the wear rates of Fe₃Si based alloys decreased as the load increased. The wear rate of Fe₃Si was higher than that of AISI 304. The addition of Cu can significantly improve the friction and wear properties of Fe₃Si based alloys and substantially reduce the wear rates of Si₃N₄ ball. The wear rate of Fe₃Si–10%Cu was 2.56 × 10⁻⁶ mm³ N⁻¹ m⁻¹ at load of 20 N and decreased to 1.64 × 10⁻⁶ mm³ N⁻¹ m⁻¹ at load of 90 N. The wear rate of Si₃N₄ ball against Fe₃Si–10%Cu was 1.41 × 10⁻⁶ mm³ N⁻¹ m⁻¹, while the wear rate of Si₃N₄ ball against AISI 304 was 5.20 × 10⁻⁶ mm³ N⁻¹ m⁻¹ at load of 90 N. The wear mechanism was dominated by micro-ploughing. The combination of mechanical action (i.e., shear, smear and transference of Cu) and tribochemical reaction of Si₃N₄ with water was responsible for the improved tribological behavior of Fe₃Si alloys containing Cu under high loads.     

Tribological Properties of Spark-Plasma-Sintered ZrO2(Y2O3)–Al2O3–Ba x Sr1?x SO4 (x?=?0.25, 0.5, 0.75) Composites at Elevated Temperature

Self-lubricating ZrO₂(Y₂O₃)–Al₂O₃–Ba _x Sr_1−x SO₄ (x = 0.25, 0.5, 0.75) composites have been fabricated by spark plasma sintering (SPS) method. The tribological properties have been evaluated using a high-temperature friction and wear tester at room temperature and 760 °C in dry sliding against alumina ball. The composites exhibit distinct improvements in effectively reducing friction and wear, as compared to the unmodified ZrO₂(Y₂O₃)–Al₂O₃ ceramics. The ZrO₂(Y₂O₃)–Al₂O₃–Ba _x Sr_1−x SO₄ (x = 0.25, 0.5, 0.75) composites have great low and stable friction coefficients of less than 0.15 and wear rates in the order of 10^− 6mm³/Nm at 760 °C. Delamination is considered as the dominating wear mechanism of the composites at room temperature. At elevated temperature, the formation and effective spreading of Ba _x Sr_1−x SO₄ (x = 0.25, 0.5, 0.75) lubricating films during sliding play an important role in the reduction of the friction and wear.     

Sulfate based coatings for use as high temperature lubricants

Films of CaSO₄, BaSO₄, and SrSO₄ were grown with the pulsed laser deposition technique. The high temperature lubricious properties of these films were evaluated and it was found that all three sulfates exhibited a low coefficient of friction (μ ≈ 0.15) at 600°C. X-ray diffraction studies showed the presence of carbonate crystal structures along with the sulfate crystal structures after testing. The carbonate crystal structure is composed of alternating planes of alkali earth atoms and carbonate ions. The layered structure of the carbonates may be important to the lubricating mechanism as the layered structure of the dichalcogenides contributes to their tribological properties. Various observations of the wear region suggest that the starting surface finish of the metal coupon plays a significant role in the tribological mechanism of these materials. Additional composite films containing CaSO₄ were grown with the plasma spray technique. The high temperature friction properties of these films were measured and compared to those of similar films containing CaF₂/BaF₂. Although both types of films exhibited low coefficients of friction at 600°C, analysis of the wear regions did not show the presence of CaSO₄ and CaF₂/BaF₂, respectively. Ca and/or Ba were present, though, suggesting that a new compound is formed in the wear track and that the sulfate and fluoride phases may not be providing the low friction in these composites. This revised version was published online in July 2006 with corrections to the Cover Date.     

Tribological Behaviour of SiC Particle Reinforced Al–Si Alloy

The purpose of this study is to explore the effect of SiC reinforcement along with immiscible element addition in spray formed Al–Si base alloy. The investigation is done for four different compositions, i.e., Al–Si base alloy, Al–Si/SiC, Al–Si–5Sn/SiC and Al–Si–10Sn/SiC composite. The dry sliding wear properties of base alloy and composites were investigated against EN 31 steel at five different normal loads (14.7, 24.5, 34.3, 44.1 and 53.9 N). The tests were carried out in dry sliding conditions with a sliding speed of 1.6 ms⁻¹ over pin-on-disc tribometer. Each composition is tested at four different temperatures 50, 75, 100 and 150 °C. To determine the wear mechanism, the worn surfaces of the samples were examined using scanning electron microscope (SEM). The composites emerge to be better wear resistant material than base alloy especially at higher loads. The optimum wear reduction was obtained in Al–Si–10Sn/SiC composite at all the different normal loads and temperatures.     

Effects of sintering aids and solid lubricants on tribological behaviours of CMC/Al2O3 pair at 650°C

Ten kinds of self-lubricating composites with different amounts of sintering aids and solid lubricants in Al₂O₃ matrix were fabricated by hot-pressed sintering. Their friction and wear behaviours in unlubricated sliding against Al₂O₃ were tested by using a pin-on-disk wear tester at 650°C. It was shown that the amount of sintering aids strongly affected friction coefficient and wear rate of the Al₂O₃–20Ag20CaF₂ composite, the appropriate amount of sintering aids was 10 wt% for beneficial effect on the reduction of wear at 650°C. Also it was shown that the addition of equal quantities of Ag and CaF₂ in Al₂O₃ matrix can promote the formation of the well-covered lubricating film, and effectively reduce the friction and wear. The composite with 40 wt% of lubricants (20 wt% Ag, 20 wt% CaF₂) presented an optimum tribological behavior at 650°C (friction coefficient μ is about 0.3, wear rates are about 4 x 10^-6 mm³/N,m and 5 x 10^-7 mm³/N,m for the disk and pin, respectively). This revised version was published online in August 2006 with corrections to the Cover Date.     

Tribological characteristics of polycrystalline Magnéli-type titanium dioxides

The results presented in this paper have clarified experimentally, that titania-based Magnéli-phases (Ti₄O₇/Ti₅O₉ and Ti₆O₁₁) with (121)-shear planes exhibit more anti-wear properties than lubricious (low-frictional) properties. The results for dry sliding indicate that the coefficients of friction lie in the range of 0.1–0.6 depending on sliding speed and ambient temperature. The COF decreased with increasing temperature (T= 22–800°C) and increasing sliding speed (υ= 1−6 m/s). The dry sliding wear rate was lowest for the Al₂O₃ at 1 m/s at 800°C with values of 1.7 × 10−8 and 6.4 × 10−8 mm³/N m, comparable to boundary/mixed lubrication, associated with a high dry frictional power loss of 30 W/mm². The running-in wear length and, more important, the wear rate decreased under oscillating sliding tests with increasing relative humidity. The contact pressure for high-/low-wear transition increased under oscillating sliding tests with increasing relative humidity. At room temperature and a relative humidity of 100% the steady-state wear rate under dry oscillating sliding for the couple Al₂O₃/Ti₄O₇–Ti₅O₉ was lower than 2 × 10−7 mm³/N m and therefore inferior to the resolution of the continuous wear measurement sensor. TEM of wear tracks from oscillating sliding revealed at room temperature a work-hardening as mechanism to explain the running-in behavior and the high wear resistance. The hydroxylation of titania surfaces favours the high-/low-wear transition. This revised version was published online in August 2006 with corrections to the Cover Date.     

Improving the Tribological Behavior of Graphite/Cu Matrix Self-Lubricating Composite Contact Strip by Electroplating Zn on Graphite

Studies to explore the nature of friction, and in particular thermally activated friction in macroscopic tribology, have lead to a series of experiments on thin coatings of molybdenum disulfide. Coatings of predominately molybdenum disulfide were selected for these experiments; five different coatings were used: MoS₂/Ni, MoS₂/Ti, MoS₂/Sb₂O₃, MoS₂/C/Sb₂O₃, and MoS₂/Au/Sb₂O₃. The temperatures were varied over a range from −80 °C to 180 °C. The friction coefficients tended to increase with decreasing temperature. Activation energies were estimated to be between 2 and 10 kJ/mol from data fitting with an Arrhenius function. Subsequent room temperature wear rate measurements of these films under dry nitrogen conditions at ambient temperature demonstrated that the steady-state wear behavior of these coatings varied dramatically over a range of K = 7 × 10⁻⁶ to 2 × 10⁻⁸ mm³/(Nm). It was further shown that an inverse relationship between wear rate and the sensitivity of friction coefficient with temperature exists. The highest wear-rate coatings showed nearly athermal friction behavior, while the most wear resistant coatings showed thermally activated behavior. Finally, it is hypothesized that thermally activated behavior in macroscopic tribology is reserved for systems with stable interfaces and ultra-low wear, and athermal behavior is characteristic to systems experiencing gross wear.     

Surface Energies of Magnetic Recording Head Components

The rate of material removal during fixed abrasive lapping is a function of friction coefficient, the surface tension of the lubricant and of the substrate, and the contact angles between the interfaces. In this study, the authors measured the surface energies of materials typically found in thin film magnetic recording heads using contact angle measurements and the Lifshitz–van der Waals acid/base approach. The different materials tested were Ni_xFe_y, Al₂O₃, and Al₂O₃-TiC. Sample preparation procedures were also considered. The chemical used to wash the surface was observed to affect the measured substrate surface energies. Surface energy values for samples washed with either acetone or hexane showed comparable results. The Ni_xFe_y gave the highest measured surface energy (46.3–48.8 mJ m⁻²) followed by Al₂O₃ (44.1–45.3 mJ m⁻²) and Al₂O₃-TiC (43.3–45.3 mJ m⁻²). In contrast, the oil-washed samples measured generally lower surface energy values. The study characterized the interaction of two lubricant types against the three materials. The oil-based lubricant spreads completely on oil-washed samples mainly because of the low surface tension of the oil (22.0 mJ m⁻²) and did not show measurable contact angles. In comparison, the water-soluble lubricant ethylene glycol, due to its higher surface tension (48.0 mJ m⁻²), formed higher contact angles ranging from 47.2 to 59.6° on the different substrates.     

Tribological behavior of NiAl matrix composites with addition of oxides at high temperatures

NiAl, NiAl–Cr–Mo alloy and NiAl matrix composites with addition of oxides (ZnO/CuO) were fabricated by powder metallurgy route. It was found that some new phases (such as NiZn₃, Cu_0.81Ni_0.19 and Al₂O₃) are formed during the fabrication process due to a high-temperature solid state reaction. Tribological behavior was studied from room temperature to 1000 °C on an HT-1000 ball-on-disk high temperature tribometer. The results indicated that NiAl had high friction coefficient and wear rate at elevated temperatures, while incorporation of Cr(Mo) not only enhanced mechanical properties evidently but also improved high temperature tribological properties. Among the sintered materials, NiAl matrix composite with addition of ZnO showed the lowest wear rate at 1000 °C, while CuO addition into NiAl matrix composite exhibited the self-lubricating performance and the best tribological properties at 800 °C.     

Tribological properties of self-lubricating CMC/Al2O3 pairs at high temperature in air

Three different self-lubricating ceramic matrix composites (CMCs) were fabricated by hot-pressed sintering. They are: Al₂O₃-50CaF₂, Al₂O₃-20Ag20CaF₂, and Al₂O₃-10Ag20CaF₂. Tribological tests were performed at temperatures ranging from 20°C to 800°C in air using a pin-on-disk tester. The experimental results show that the addition of the solid lubricants CaF₂ and Ag can evidently reduce the friction coefficients of alumina between 200°C and 650°C but not at room temperature and the wear rate of disks and pins at elevated temperature. The improvements in the friction and wear properties of CMC were due to the formation of a well-covered solid lubricating film. However, breakdown of the lubricating films at 800°C resulted in high friction and wear. This revised version was published online in August 2006 with corrections to the Cover Date.     

Synergistic Effect of Nano-MoS<Subscript>2</Subscript> and Anatase Nano-TiO<Subscript>2</Subscript> on the Lubrication Properties of MoS<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> Nano-Clusters

A MoS₃ precursor deposited on anatase nano-TiO₂ is heated at 450 °C in an H₂ atmosphere to synthesize MoS₂/TiO₂ nano-clusters. The nano-clusters are then characterized, and their tribological properties are evaluated. MoS₂ is found to be composed of layered structures with 1–10 nm thicknesses, 10–30 nm lengths, and 0.63–0.66 nm layer distances. The MoS₂ sizes in the MoS₂/TiO₂ nano-clusters are smaller and their layer distances are larger than those of pure nano-MoS₂. The MoS₂/TiO₂ nano-clusters also present a lower average friction coefficient than pure nano-MoS₂, but the anti-wear properties of both the nano-clusters and pure nano-MoS₂ are similar. X-ray photoelectron spectroscopy indicates that nano-TiO₂ and the element Mo are transferred to the friction surface from the MoS₂/TiO₂ nano-clusters through a tribochemical reaction. This produces a lubrication film containing TiO₂, MoO₃, and other chemicals. The nano-MoS₂ changes in size and layer distance when combined with nano-TiO₂, producing a synergistic effect. This may further be explained using a micro-cooperation model between MoS₂ nano-platelets and TiO₂ solid nanoparticles.     

Speed and Atmosphere Influences on Nanotribological Properties of NbSe<Subscript>2</Subscript>

Nanotribological properties of NbSe₂ are studied using an atomic friction force microscope. The friction force is measured as a function of normal load and scan speeds ranging from 10 nm s⁻¹ to 40 μm s⁻¹ under two atmospheres (air and argon). At low speed, no effect of atmosphere is noticed and a linear relationship between the friction and normal forces is observed leading to a friction coefficient close to 0.02 for both atmospheres. At high speed, the tip/surface contact obeys the JKR theory and the tribological properties are atmosphere dependent: the shear stress measured in air environment is three times lower than the one measured under argon atmosphere. A special attention is paid to interpret these results through numerical data obtained from a simple athermal model based on Tomlinson approach.     

Molecular beam epitaxy of BaF<Subscript>2</Subscript>/CaF<Subscript>2</Subscript> buffer layers on the Si(100) substrate for monolithic photoreceivers

This paper describes the study of the surface morphology of BaF2 epitaxial films grown by means of molecular beam epitaxy in various growth regimes on a CaF₂/Si(100) surface, which is performed by means of atomic force microscopy. The CaF₂ layers were obtained on a Si(100) substrate in a low-temperature growth regime (T _s = 500 °C). The technological regimes of growth of BaF₂ continuous films with a smooth surface on CaF₂/Si(100), suitable as buffer layers for the subsequent growth of PbSnTe layers or other semiconductors, such as A₄B₆, and solid solutions based on them.