Dielectric and Piezoelectric Properties of Na<Subscript>0.5</Subscript>Bi<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript>-K<Subscript>0.5</Subscript>Bi<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript>-NaNbO<Subscript>3</Subscript>Lead-Free Ceramics

The ternary lead-free piezoelectric ceramics system of (1 – x) [0.88Na_0.5Bi_0.5TiO₃-0.12K_0.5Bi_0.5TiO₃] – xNaNbO₃(x = 0, 0.02, 0.04, 0.06, 0.08, 0.10) were synthesized by conventional solid state reaction method. The crystal structure, dielectric, piezoelectric properties and P-E hysteresis loops were investigated. The crystalline structure of all compositions is mono-perovskite phase ascertained by XRD, and the lattice constant was calculated from the XRD data. Temperature dependence of dielectric constant _r and dissipation factor tan measurement revealed that all compositions experienced two phase transitions: from ferroelectric to anti-ferroelectric and from anti-ferroelectric to paraelectric, and these two phase transitions have relaxor characteristics. Both transition temperatures T_d and T_m are lowered due to introduction of NaNbO₃. P-E hysteresis loops show that 0.88Na_0.5Bi_0.5TiO₃-0.12K_0.5Bi_0.5TiO₃ ceramics has the maximum P_r and E_c corresponding to the maximum values of electromechanical coupling factor K_p and piezoelectric constant d_33. The piezoelectric constant d₃₃ and electromechanical coupling factor K_p decrease a little, while the dielectric constant ₃₃^T/₀ improves much more when the concentration of NaNbO₃ is 8 mol%.     

The Similar Defect Chemistry of Highly-Doped SrBi<Subscript>2</Subscript>Ta<Subscript>2</Subscript>O<Subscript>9</Subscript> and SrBi<Subscript>2</Subscript>Nb<Subscript>2</Subscript>O<Subscript>9</Subscript>

The equilibrium electrical conductivities of undoped SrBi₂Ta₂O₉ (SBT) and SrBi₂Nb₂O₉ (SBN) have been shown to behave quite differently. SBT has the behavior expected for a 1% acceptor-doped oxide, while SBN behaves like a 1% donor-doped oxide. This difference has been related to the substantial cation place exchange that occurs between the Bi^{+ 3} and Sr^{+ 2} ions in the alternating layers of the structure. It was proposed that this place exchange is not entirely self-compensating, as would be expected for a simple, isotropic oxide, but that there is some local compensation within each layer by lattice and/or electronic defects. It is now shown that the equilibrium conductivity of 3% donor-doped SBT is similar to that of undoped SBN, while the equilibrium conductivity of 3% acceptor-doped SBN resembles that of undoped SBT. Thus the defect chemistrys of the two compounds are quite similar, but the equilibrium conductivities are displaced along a doping axis.     

Mechanical and electrical properties of Bi<Subscript>1.5-x</Subscript>La<Subscript>x</Subscript>Zn<Subscript>0.92</Subscript>Nb<Subscript>1.5</Subscript>O<Subscript>6.92</Subscript> pyrochlore ceramics

BiFeO₃-Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃ (BF-PMN-PT) ternary ceramics with pure perovskite phase were prepared through a two-step solid reaction method. Based on structural analysis, the ternary phase diagram of BF-PMN-PT solid solution at room temperature has been established. The Curie temperature T_C, remnant polarization P_r and piezoelectric constant d₃₃ vary in the range of 138 to 225 °C, 15.12 to 23.65 μC/cm² and 129 to 276 pC/N, respectively. The coercive field Ec increases gradually from 5.77 to 29.56 kV/cm upon PT content increasing. The magnetic study suggests that the magnetism turns from diamagnetism for PMN-PT to paramagnetism for BF-PMN-PT by adding BiFeO₃ into PMN-PT and adding more content of BF does not change the paramagnetism further.     

Raman and infrared spectroscopy of Na<Subscript>0.5</Subscript>Bi<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript> - BaTiO<Subscript>3</Subscript> ceramics

Lead-free Na_0.5Bi_0.5TiO₃ -BaTiO₃ ceramics have been prepared in the whole range of concentrations and studied at room-temperature by means of X-ray, Raman scattering and infrared techniques. X-ray measurements revealed rhombohedral, rhombohedral-tetragonal boundaries and tetragonal modifacations depending on the contents of BaTiO₃. The distinct changes of the Raman and infrared spectra with increasing of BaTiO₃ content, which were correlated with X-ray results, were observed. The broad phonon spectra indicated the disorder in the A site of Na_0.5Bi_0.5TiO₃ -BaTiO₃ system.     

Improvement of Bi<Subscript>2</Subscript>Sr<Subscript>2</Subscript>Co<Subscript>2</Subscript>O<Subscript>y</Subscript> thermoelectric performances by Na doping

Bi₂Sr_2-xNa_xCo₂O_y thermoelectric materials with x = 0, 0.025, 0.05, 0.075, 0.10, 0.125, and 0.15 have been prepared by the classical solid state reaction. Microstructure has shown an important grain growth when Na is added, leading to very high bulk densities confirmed through density measurements. These modifications have produced a drastic decrease of electrical resistivity without significant modification of Seebeck coefficient. As a consequence, Power Factor has been increased in all Na-doped samples, reaching the maximum value (0.21 mW/K².m at 650 °C) for 0.075 Na samples, which is fairly close to the reported for single crystals.     

Microwave Dielectric Properties of CuO-V<Subscript>2</Subscript>O<Subscript>5</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-Doped ZnNb<Subscript>2</Subscript>O<Subscript>6</Subscript> Ceramics with Low Sintering Temperature

Microwave dielectric properties of low temperature sintering ZnNb₂O₆ ceramics doped with CuO-V₂O₅-Bi₂O₃ additions were investigated systematically. The co-doping of CuO, V₂O₅ and Bi₂O₃ can significantly lower the sintering temperature of ZnNb₂O₆ ceramics from 1150 to 870C. The secondary phase containing Cu, V, Bi and Zn was observed at grain boundary junctions, and the amount of secondary phase increased with increasing CuO-V₂O₅-Bi₂O₃ content. The dielectric properties at microwave frequencies (7–9 GHz) in this system exhibited a significant dependence on the relative density, content of additives and microstructure of the ceramics. The dielectric constant ( _r) of ZnNb₂O₆ ceramics increased from 21.95 to 24.18 with increasing CuO-V₂O₅-Bi₂O₃ additions from 1.5 to 4.0 wt%. The quality factors (Q× f) of this system decreased with increasing CuO-V₂O₅-Bi₂O₃ content and ranged from 36118 to 67100 GHz for sintered ceramics, furthermore, all Q× f values of samples with CuO-V₂O₅-Bi₂O₃ additions are lower than that of un-doped ZnNb₂O₆ ceramics sintered at 1150C for 2 h. The temperature coefficient of resonant frequency ( _f) changed from –33.16 to –25.96 ppm/C with increasing CuO-V₂O₅-Bi₂O₃ from 1.5 to 4.0 wt%     

Coke-tolerant La<Subscript>2</Subscript>Sn<Subscript>2</Subscript>O<Subscript>7</Subscript>-Ni-Gd<Subscript>0.1</Subscript>Ce<Subscript>0.9</Subscript>O<Subscript>1.95</Subscript> composite anode for direct methane-fueled solid oxide fuel cells

Direct CH₄-fueled solid oxide fuel cells (SOFCs) have been studied for a few decades, but carbon depositions on the Ni-based anodes are still remained as a major problem. In order to enhance coke tolerances and durability of SOFCs, La₂Sn₂O₇ nano-powders are prepared by co-precipitation. The SOFCs with the different amounts of the La₂Sn₂O₇ nano-powders in the Ni-GDC anodes are tested under dry CH₄, and the 0.3 wt.% La₂Sn₂O₇-Ni-GDC (0.3LNG) anodes show the highest cell performances of all anodes. The maximum power density of the cell is approximately 0.55 W cm^?2 at 650 °C. The durability of the 0.3LNG cell is significantly enhanced without any carbon formations, showing approximately 0.69 V over 600 h at 0.3 A cm^?2, whereas the conventional Ni-GDC cell is stopped only after 90 h. It suggests that the 0.3LNG is a promising anode material to enhance coke-tolerances and durability of direct-methane fuel cells.     

Analysis of domain structure in the Ce<Subscript>0.8</Subscript>Sm<Subscript>0.15</Subscript>Ca<Subscript>0.05</Subscript>O<Subscript>1.875</Subscript> sample

A Ce_0.8Sm_0.15Ca_0.05O_1.875 (S15C05DC) sample is synthesized by a solid-state reaction serving as a potential electrolyte material for intermediate-temperature solid oxide fuel cells. The sintered sample was found to be dense with a cubic fluorite structure. The addition of Ca²⁺ can act as a CeO₂ sintering aid for accelerating the process. The microstructures and properties of the sample were analyzed by X-ray diffractometry, Raman spectroscopy, scanning electron microscopy, thermomechanical analysis, and transmission electron microscopy. Existing oxygen vacancies in the sample are indicated by a Raman peak at 558 cm^?1. The thermal expansion coefficient of the S15C05DC sample at 200–800 °C is approximately 12–14 × 10^?6 °C^?1. The control of domain size is an important factor for improving the conductivity of S15C05DC. Local clustered nano-domains, with higher Sm₂O₃ concentrations, were found to regularly arrange to induce the formation of a nanoscale C-type superlattice structure. While Ca doping decreased the formation of the C-type Sm₂O₃ structure.     

Lead-free (K<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>)<Subscript>0.95</Subscript>(LiSb)<Subscript>0.05</Subscript>Nb<Subscript>0.95</Subscript>O<Subscript>3</Subscript>-BaTiO<Subscript>3</Subscript> piezoceramics

Lead-free (1-x)(K_0.5Na_0.5)_0.95(LiSb)_0.05Nb_0.95O₃-xBaTiO₃ (abbreviated as (1-x)KNNLS-xBT) piezoceramics were synthesized by conventional solid state sintering and the effect of BaTiO₃ on the microstructure, dielectric and piezoelectric properties was investigated. It was found that both orthorhombic-tetragonal (T _O-T) and tetragonal-cubic (T _C) phase transition temperatures decreased obviously with increasing BaTiO₃ content. Although proper amount of BaTiO₃ facilitated the sintering of (1-x)KNNLS-xBT ceramics, the addition of BaTiO₃ affected the relaxor behavior slightly and it was not beneficial to improve piezoelectric strain coefficient d ₃₃, remnant polarization P _r and piezoelectric coupling constant k _p.     

Properties and crystallization kinetics of low temperature co-fired Li<Subscript>2</Subscript>O-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> electroceramics

The glass-ceramic in the Li₂O-Al₂O₃-SiO₂ system has been prepared by melt quenching route. The crystallization kinetics was studied by differential scanning calorimetry. The effects of sintering temperature on the phase transformation, sintering behavior, bulk density, microstructure, thermal expansion, bending strength and dielectric properties were also investigated by X-ray diffractometry and scanning electron microscopy. (Li, Mg, Zn)_1.7Al₂O₄Si₆O₁₂ is the first crystalline phase forming in the glass-ceramic and transforms to LiAlSi₃O₈ phase at 800 °C. The other two crystalline phases of ZrO₂ and CaMgSi₂O₆ precipitate at 700 and 750 °C, respectively. The densification of this LAS glass-ceramic starts at around 730 °C and stops at about 805 °C. The coefficient of thermal expansion increases with the increasing sintering temperature. The sample sintered at 800 °C for 30 min exhibited excellent properties. The nonisothermal activation energy of crystallization is 149 kJ/mol and the values of Avrami constant (n) are in the range of 3.2 to 3.9. The LAS glass-ceramic sintered at 800 °C for 30 min showed excellent properties. This makes that this material suitable for a number of LTCC applications.     

Nano-sized Pr<Subscript>0.8</Subscript>Sr<Subscript>0.2</Subscript>Co<Subscript>1-x</Subscript>Fe<Subscript>x</Subscript>O<Subscript>3</Subscript> powders prepared by single-step combustion synthesis for solid oxide fuel cell cathodes

Different sets of perovskite-type oxides of general formula Pr_0.8Sr_0.2Co_1-xFe_xO_3-δ (x = 0.0, 0.2, 0.5, 0.8 and 1.0) were successfully prepared by low-cost single-step combustion synthesis at low temperatures based on the auto-ignition reaction of a nitrate solution in the presence of citric acid. Thermogravimetric and differential thermal analysis was carried out on nitrate-citrate precursors to determine the perovskite-phase formation process. The results revealed that the nitrate-citrate precursor exhibited self-propagating combustion behavior. Pr_0.8Sr_0.2Co_1-xFe_xO_3-δ powders showed an orthorhombic single-phase, with their unit cell volume increasing as a function of the Fe content (x). Scanning electron microscopy observations showed that the prepared powders were nanocrystalline. The Pr_0.8Sr_0.2Co_1-xFe_xO_3-δ powders were characterized as fuel cell electrodes on Ce_0.8Sm_0.2O_2-δ pellets in symmetrical cells, and the electrochemical properties of the electrode/electrolyte interfaces were investigated using electrochemical impedance spectroscopy (EIS) as a function of the temperature, Fe content (x) and oxygen partial pressure.     

Effects of MnO<Subscript>2</Subscript> addition on microstructure and electrical properties of (Bi<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>) <Subscript>0.94</Subscript>Ba<Subscript>0.06</Subscript>TiO<Subscript>3</Subscript> ceramics

In this letter, MnO₂-doped (Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ (BNBT-6) lead-free piezoelectric ceramics were synthesized by solid state reaction, and the microstructure and electrical properties of the ceramics were investigated. X-ray diffraction (XRD) reveals that all specimens take on single perovskite type structure, and the diffraction peaks shift to a large angle as the MnO₂ addition increases. Scanning electron microscopy shows that the grain sizes increases, and then decreases with increasing the MnO₂ content. The experiment results indicate that the electrical properties of ceramics are significantly influenced by the MnO₂ content, and the ceramics with homogeneous microstructure and excellent electrical properties are obtained with addition of 0.3 wt% MnO₂ and sintered at 1160°C. The piezoelectric constant (d₃₃), the electromechanical coupling factor (k _p ), the dissipation factor (tan δ) and the dielectric constant (ɛ _r ) reach 160 pC/N, 0.29, 0.026 and 879, respectively. These excellent properties indicate that the MnO₂-doped BNBT-6 ceramics can be used for actuators.     

Structure and properties of Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> doped Bi(Mg<Subscript>1/2</Subscript>Ti<Subscript>1/2</Subscript>)O<Subscript>3</Subscript>-0.38PbTiO<Subscript>3</Subscript> ceramics with MPB composition

0.62Bi(Mg_1/2Ti_1/2)O₃-0.38PbTiO₃-xwt%Bi₂O₃ (BMT-0.38PT-xBi₂O₃) ceramics were prepared by conventional powder-processing method. It indicated that the morphotropic phase boundary (MPB) region located in 0.0?≤?x?≤?0.3. For x?=?0.3, it exhibited good piezoelectric properties, d₃₃ ~245pC/N and k_p ~40 %. With the increase of Bi₂O₃ content, the Curie temperature (T_c) was found to increase, and the dielectric loss was found to decrease above 200 °C compared with BMT-0.38PT sample. Finally, it can be found that depolarization temperature was around 350 °C by thermal depoling method.     

Microelectrodes for local conductivity and degradation measurements on Al stabilized Li<Subscript>7</Subscript>La<Subscript>3</Subscript>Zr<Subscript>2</Subscript>O<Subscript>12</Subscript> garnets

The attractiveness of Li₇La₃Zr₂O₁₂ (LLZO) cubic based garnets lies in their high ionic conductivity and the combination of thermal and electrochemical stability. However, relations between composition and conductivity as well as degradation effects are still not completely understood. In this contribution we demonstrate the applicability of microelectrodes (Ø = 20–300 μm) for electrochemical impedance spectroscopy (EIS) studies on LLZO garnets. Microelectrodes allow to obtain local information on the ionic conductivity. A comparison between the overall performance of the sample (3.3 × 10^?4 S cm^?1) and local measurements revealed differences in conductivity with a maximum of the locally measured values of 6.3 × 10^?4 S cm^?1 and a minimum of 2.6 × 10^?4 S cm^?1. One reason behind these conductivity variations is most probably a compositional gradient in the sample. In addition, microelectrodes are very sensitive to conductivity changes near to the surface. This was used to investigate the effect of moisture in ambient air on the conductivity variations of LLZO. Substantial changes of the measured Li-ion transport resistance were found, particularly for smaller microelectrodes which probe sample volumes close to the surface.     

The investigation of key processing parameters in fabrication of Pb(Zr<Subscript><Emphasis Type="Bold">x</Emphasis></Subscript>Ti<Subscript>1−<Emphasis Type="Bold">x</Emphasis></Subscript>)O<Subscript>3</Subscript> thick films for MEMS applications

It has always been a big challenge to deposit dense and crack-free Pb(Zr _x Ti_1−x )O₃ (PZT) thick films through Chemical Solution Deposition (CSD). In this study, a sol with higher concentration (≥0.6 M) was spun onto a platinised silicon substrate. The single layer thickness of a dense, crack-free film with several tenths of nanometres up to 350 nm could be obtained. It was found that the key factor in obtaining thick crack-free films was to choose an appropriate heating profile. In this study, the deflection of a single layer at various stages of heating was analysed through the measurement of the wafer curvature using the Dektak profilometer. As a result three characteristic changes of deflection were found, happening at 300, 450 and 500 °C. These obvious changes in wafer deflection closely relate to the transformations of sol-to-gel, gel-to-amorphous solid and amorphous solid-to-solid crystals. Furthermore, using these temperatures to thermally treat each single layer, it was possible to obtain thick crack-free films by repeatedly spin coating. The dielectric and piezoelectric properties, such as d_33,f and e_31,f, of the films with different thicknesses and orientations were measured and compared.     

Phase transition,microstructure and properties of (Na<Subscript>0.5</Subscript>Bi<Subscript>0.5</Subscript>)<Subscript>1-x</Subscript>Ba<Subscript>x</Subscript>TiO<Subscript>3</Subscript> lead-free piezoelectric ceramics

In this article, (Na_0.5Bi_0.5)_1-xBa_xTiO₃ lead-free piezoelectric ceramics were prepared by solid-state reaction. The influence of Ba contents on phase structures, compositional distribution and electrical properties of (Na_0.5Bi_0.5)_1-xBa_xTiO₃ ceramics were systematically investigated to further understand the nature of phase transition. It was found that the phase structure of (Na_0.5Bi_0.5)_1-xBa_xTiO₃ transforms from rhombohedral to tetragonal symmetry at x = 0.06 ~ 0.07 and Ba²⁺ segregation forms the coexistence of Ba-rich tetragonal and Ba-deficient rhombohedral phases close to MPB. The electrical properties of prepared samples regularly changed with Ba content, which is closely related to the distribution of rhombohedral and tetragonal phases. The prepared sample near MPB exhibited the largest dielectric constant and the excellent piezoelectric properties (the maximal measuring field reached 78 kV/cm and the piezoelectric constant d ₃₃ = 151pC/N).     

Microwave dielectric properties of Na<Superscript>+</Superscript> and M<Superscript>3+</Superscript>-doped Ba(Mg<Subscript>0.5</Subscript>W<Subscript>0.5</Subscript>)O<Subscript>3</Subscript> ceramics

In this study, phase evolution, microstructure, and microwave dielectric properties of (Ba_0.98Na_0.02)(Mg_0.48M³⁺_0.02W_0.5)O₃ (M³⁺?=?Al, Ga, Sc, In, Yb, Y, Dy, Gd, and Sm) ceramics sintered at 1700 °C for 1 h were investigated. All the compounds exhibited an ordered cubic perovskite structure. Regardless of the ionic radius of the doped M³⁺ ions, BaWO₄ was detected as the secondary phase in all the compounds. The field emission scanning electron microscopy (FE-SEM) images revealed a dense microstructure in all the compounds, except in the Al-doped compound, which exhibited an insufficient grain growth. The large and irregularly shaped grains indicated that the liquid phase sintering occurred. Splitting of the A_1g(O) mode was observed in the Raman spectra of large M³⁺ ion-doped compounds. Splitting of the F_2g modes did not occur and the bands were sharp, indicating that the cubic symmetry was retained. As the ionic radius of the doped M³⁺ ions increased, the dielectric constant (ε_r) increased slightly. The compounds doped with M³⁺?=?Sc, In, Yb, and Y exhibited a very high quality factor (Q?×?f₀) in the range of 250,000 ~ 280,000 GHz. In the case of the compounds doped with M³⁺?=?Al, Ga, Sc, In, Yb, Y, and Dy, the value of the temperature coefficient of resonant frequency (τ_f) was in the range of ?24 ~ ?19 ppm/°C, while the Gd and Sm-doped compounds exhibited positive values of 2.8 and 31.2 ppm/°C, respectively. The dielectric constant, quality factor, and temperature coefficient of resonant frequency of the In-doped compound, i.e., (Ba_0.98Na_0.02)(Mg_0.48In_0.02W_0.5)O₃, were 18.7, 286,557 GHz, and???24.4 ppm/°C, respectively.     

Defects and Transport in Langasite II: Donor-doped (La<Subscript>3</Subscript>Ga<Subscript>4.75</Subscript>Nb<Subscript>0.25</Subscript>SiO<Subscript>14</Subscript>)

The electrical conductivity of Nb doped langasite (La₃Ga_4.75Nb_0.25SiO₁₄) was examined as a function of temperature and oxygen partial pressure by complex impedance spectroscopy. A pO₂-independent regime was found at high pO₂ followed by a pO₂^{− 1/6} dependent regime at low pO₂. A defect model consistent with these results was derived in which the electron density n is fixed by the density of ionized Nb donors at high pO₂ and by the generation of oxygen vacancies at low pO₂. The temperature and oxygen partial pressure dependence of the electron density was obtained independently by thermoelectric power measurements. The Nb donor ionization energy was determined to be 1.52 ± 0.06 eV, confirming Nb to be a deep donor in langasite. By combining conductivity and thermoelectric power data, an expression for the electron mobility given by μ_e = 1.1× 10^{− 2}exp( ) was obtained. After evaluating the temperature dependent conductivity data under reducing conditions, in light of the defect model, a value for the reduction enthalpy (E_r = 6.57 ± 0.24 eV) was derived.     

Effects of Processing Conditions on the Dielectric Properties of CaCu<Subscript>3</Subscript>Ti<Subscript>4</Subscript>O<Subscript>12</Subscript>

There have been a number of recent reports of anomalously large permittivities (ε _r ≈ 10⁴) in the material CaCu₃Ti₄O₁₂. The dielectric spectra is characterized by a large, relatively temperature independent permittivity near room temperature which exhibits a dielectric relaxation above 100 K. The crystal structure of CaCu₃Ti₄O₁₂ can be described as pseudo-perovskite with a cubic unit cell with a lattice constant of 7.391 Å. The ubiquitous occurrence of this dielectric behavior in ceramics, single crystals, and thin films suggests that the polarization is not related to a simple conducting grain/insulating grain boundary-type system. While the precise origin of the dielectric response is not entirely clear, in this work it is shown that processing conditions have a significant influence on the room temperature dielectric properties. Specifically, the permittivity and loss exhibit a strong dependence on the oxygen partial pressure and sintering time. In fact, studies of the effects of sintering time and supporting evidence from capacitance-voltage measurements conclusively show that there is no direct relationship between the permittivity and grain size, as is the case in classical boundary layer systems. Lastly, with aliovalent doping the room temperature dielectric properties can be optimized to provide a high permittivity (ε _r ～ 8,000) dielectric with relatively low loss (tan δ < 0.05 at 1 kHz).     

Enhancement of thermoelectric performance in rare earth-doped Sr<Subscript>3</Subscript>Ti<Subscript>2</Subscript>O<Subscript>7</Subscript> by symmetry restoration of TiO<Subscript>6</Subscript> octahedra

Aiming at the realization of the enhancement of thermoelectric performance through structural modification, the present work has clarified the significant effects of rare earth (RE=Gd, Sm, Nd, and La) doping at Sr-sites in Sr₃Ti₂O₇, both on the structural restoration of distorted TiO₆ octahedra and on the Seebeck coefficient, especially at high temperatures. The preferential substitution of RE ³⁺ at the nine-coordinate Sr-sites can facilitate the degeneration of the conduction band (Ti 3d-t _2g ) orbital, owing to its special capability in restoring TiO₆ octahedra to a higher state of symmetry and thus enhance the density of states (DOS) effective mass of the carriers, which gives rise to a rather large increase in the Seebeck coefficient. The present findings have affirmed the effectiveness of structural restoration in enhancing the Seebeck coefficient by Sr-site-doping, which will help establish a useful solution for Ti-based thermoelectric oxides with inherently distorted TiO₆ octahedra to achieve high thermoelectric performance.