High-Temperature Strength of Liquid-Phase-Sintered SiC with AlN and Re2O3 (RE = Y, Yb)

Using AlN and RE₂O₃ (RE = Y, Yb) as sintering additives, two different SiC ceramics with high strength at 1500°C were fabricated by hot-pressing and subsequent annealing under pressure. The ceramics had a self-reinforced microstructure consisting of elongated α-SiC grains and a grain-boundary glassy phase. High-temperature strength up to 1600°C was measured and compared with that of the SiC ceramics fabricated with AlN and Er₂O₃. SiC ceramics with AlN and Y₂O₃ showed the best strength (∼630 MPa) at 1500°C, while SiC ceramics with AlN and Er₂O₃ the best strength (∼550 MPa) at 1600°C.     

Crack-Healing Behavior of Liquid-Phase-Sintered Silicon Carbide Ceramics

Crack-healing behavior of liquid-phase-sintered (LPS) SiC ceramics has been studied as functions of heat-treatment temperature and crack size. Results showed that heat treatment in air could significantly increase the indentation strength. The heat-treatment temperature has a profound influence on the extent of crack healing and the degree of strength recovery. The optimum heat-treatment temperature depends on the softening temperature of an intergranular phase in each material. After heat treatment at the optimum temperature in air, the crack morphology almost entirely disappeared and the indentation strength recovered to the value of the smooth specimens at room temperature for the investigated crack sizes up to ∼200 μm. In addition, a simple heat treatment of SiC ceramics sintered with Al₂O₃–Y₂O₃–CaO at 1100°C for 1 h in air resulted in even further improvement of the strength, to a value of 1054 MPa (∼150% of the value of the unindented strength). Crack closure and rebonding of the crack wake due to oxidation of cracked surfaces were suggested as a dominant healing mechanism operating in LPS-SiC ceramics.     

High-Strength Porous Silicon Carbide Ceramics by an Oxidation-Bonding Technique

Porous silicon carbide (SiC) ceramics were fabricated by an oxidation-bonding process in which the powder compacts are heated in air so that SiC particles are bonded to each other by oxidation-derived SiO₂ glass. Because of the crystallization of amorphous SiO₂ glass into cristobalite during sintering, the fracture strength of oxidation-bonded SiC ceramics can be retained to a relatively high level at elevated temperatures. It has been shown that the mechanical strength is strongly affected by particle size. When 0.6 μm SiC powders were used, a high strength of 185 MPa was achieved at a porosity of ∼31%. Moreover, oxidation-bonded SiC ceramics were observed to exhibit an excellent oxidation resistance.     

High-Temperature Strength of Sinter-Forged Silicon Nitride with Lutetia Additive

A sinter-forging technique was successfully applied to fabricate a silicon nitride with a lutetia (Lu₂O₃) additive. The sinter-forged specimen had a strongly anisotropic microstructure where rodlike silicon nitride grains preferentially aligned perpendicular to the forging direction. The specimen exhibited superior strength of ∼700 MPa at 1500°C. This strength was highest when compared with previous silicon nitrides at temperatures >1400°C. Such superior high-temperature strength was attributed to grain alignment as well as to the refractory grain-boundary glassy phase and the existence of glass-free grain boundaries.     

Microstructural Changes in Liquid-Phase-Sintered Silicon Carbide during Creep in an Oxidizing Environment

The knowledge of the microstructural evolution during exposure to high temperatures is important to understanding the mechanisms responsible for the creep resistance of silicon carbide (SiC) ceramics. This includes not only the phase transformation of the SiC grains, but also the phase transformations of the oxynitride grain-boundary phases. For this study, a series of SiC specimens were prepared with varying molar ratios of AlN-Y₂O₃ additives. Increased creep resistance was observed in specimens with an additive system containing a 2:3 molar ratio or 60 mol% Y₂O₃. A continuous oxide layer of Y₂Si₂O₇ formed at the surface during elevated temperature testing in air. No blistering or cracking was observed in this oxide coating. Further increase of the creep resistance was achieved by a post-sintering nitrogen anneal.     

Resistance of Alumina-Spodumene Ceramics to Thermal Shock

A processing strategy is presented for obtaining alumina-spodumene ceramics with controlled microstructures from a new, low-cost alumina powder and spodumene (Li₂OAl₂O₃·4SiO₂) mineral, both being produced in Western Australia. The addition of 15 wt%β-spodumene to alumina is used to produce ceramics with (i) high thermal expansion mismatch and (ii) a glassy phase to aid in liquid-phase sintering. Specifically, the effects of spodumene addition and grain size on tolerance to thermal shock are addressed. The thermal shock resistance of the alumina-spodumene ceramics is evaluated by water quenching and subsequent three-point bend testing of strength diminution. Comparisons are made with results from parallel experiments conducted using a pure monolithic alumina ceramic. The reference alumina shows the expected substantial strength losses when thermally quenched from ∼200°C above room temperature. By contrast, the alumina-spodumene ceramics, while displaying reduced strength relative to the reference aluminas, exhibit minimal strength degradation under severe thermal shock conditions.     

Qualitative and Quantitative Evaluation of Silicon Nitride Grain-Boundary Phase by Cryogenic Specific Heat Measurements

Three types of Si₃N₄ have been hot isostatically pressed at 1700°C under 60 MPa for 1 h in a capsule. The quantity and quality (i.e., crystalline or glassy structure) of the grain-boundary phase of the three types of Si₃N₄ can be evaluated by measuring cryogenic specific heats. The specific heats of Si₃N₄ ceramics with Al₂O₃ and Y₂o₃, additives have been measured at different temperatures between 10 and 40 K. The temperature dependency of measured cryogenic specific heat provides quantitative and qualitative information of the grain-boundary phases. This method is very useful for evaluating small changes in the amount and crystalline structure of grain-boundary phases and can clarify different heat histories of the sintering processes in Si₃N₄ ceramics. This proposed method is nondestructive, and the sensitivity can be extremely high. This method eventually leads to a new quality control method of ceramics.     

Flexural Creep Deformation of ZrB2/SiC Ceramics in Oxidizing Atmosphere

Flexural creep of ZrB₂/0–50 vol% SiC ceramics was characterized in oxidizing atmosphere as a function of temperature (1200°–1500°C), stress (30–180 MPa), and SiC particle size (2 and 10 μm). Creep behavior showed strong dependence on SiC content and particle size, temperature and stress. The rate of creep increased with increasing SiC content, temperature, and stress and with decreasing SiC particle size, especially, at temperatures above 1300°C. The activation energy of creep showed linear dependence on the SiC content increasing from about 130 to 511 kJ/mol for ceramics containing 0 and 50 vol% 2-μm SiC, respectively. The stress exponent was about 2 for ZrB₂ containing 50 vol% SiC regardless of SiC particle size, which is an indication that the leading mechanism of creep for this composition is sliding of grain boundaries. Compared with that, the stress exponent is about 1 for ZrB₂ containing 0–25vol% SiC, which is an indication that diffusional creep has a significant contribution to the mechanism of creep for these compositions. Cracking and grain shifting were observed on the tensile side of the samples containing 25 and 50 vol% SiC. Cracks propagate through the SiC phase confirming the assumption that grain-boundary sliding of the SiC grains is the controlling creep mechanism in the ceramics containing 50 vol% SiC. The presence of stress, both compressive and tensile, in the samples enhanced oxidation.     

Impurity Phases in Hot-Pressed Si3N4

Impurity phases in commercial hot-pressed Si₃N₄ were investigated using transmission electron microscopy. In addition to the dominant, β-Si₃N₄ phase, small amounts of Si₂N₂O, SiC, and WC were found. Significantly, a continuous grain-boundary phase was observed in the ∼ 25 high-angle boundaries examined. This film is ∼ 10 Å thick between, β-Si₃N₄ grains and ∼ 30 Å thick between Si₂N₂O and β-Si₃N₄ grains.     

Fracture Strength and Microstructure of β-SiAlON with Hafnia Addition

The influence of HfO₂ addition on the fracture strength and microstructure of ß-SiAlON ceramics sintered from Si₃N₄ and Al₂O₃ powders was investigated. The strength was increased by the addition of HfO₂, from ∼500 MPa to 700 MPa, and was almost constant from ambient temperature to 1300°C. Monoclinic HfO₂ grains that were distributed in the SiAlON grain boundaries had a flat shape (∼20 nm thick) and were surrounded by an amorphous phase. The aluminum concentration in ß-SiAlON in the samples with an Al₂O₃ starting composition of 15 wt% was decreased by the addition of HfO₂. The amount of secondary phases was very small at grain boundaries between the SiAlON grains; amorphous phases were observed infrequently at the triple points but were very small (∼20 nm). The effects of HfO₂ addition on the mechanism of the microstructure development and fracture strength are discussed.     

Low-Temperature Fabrication of Cordierite Ceramics from Kaolinite and Magnesium Hydroxide Mixtures with Boron Oxide Additions

Thermal reactions of mixtures of ultrafine particles of magnesium hydroxide (Mg(OH)₂) and kaolinite in a composition of MgO:Al₂O₃:2SiO₂ were investigated to obtain dense cordierite ceramics at temperatures <1000°C. While heating the mixture of kaolinite and Mg(OH)₂ with the equivalent of 2 mass% of boron oxide (B₂O₃) (in the form of magnesium borate, 2MgOB₂O₃), an amorphous phase formed at a temperature of ∼850°C after thermal decomposition. Firing the mixture at a temperature of 900°C yielded dense ceramics with an apparent porosity of almost zero. The addition of B₂O₃ promoted the densification at 850°-900°C and accelerated the crystallization of alpha-cordierite. The specimen with 3 mass% of B₂O₃ that was fired at a temperature of 950°C showed a linear thermal expansion coefficient of ∼3 × 10⁻⁶ K⁻¹, a bending strength of >200 MPa, and a relative dielectric constant of 5.5 at 1 MHz. These cordierite ceramics may be used as substrate materials for semiconductor interconnection applications.     

Grain-Boundary Microstructure and Chemistry of a Hot Isostatically Pressed High-Purity Silicon Nitride

Two high-purity Si₃N₄ materials were fabricated by hot isostatic pressing without the presence of sintering additives, using an amorphous laser-derived Si₃N₄ powder with different oxygen contents. High-resolution transmission electron microscopy and electron energy-loss spectroscopy (EELS) analysis of the Si₃N₄ materials showed the presence of an amorphous SiO₂ grain-boundary phase in the three-grain junctions. Spatially resolved EELS analysis indicated the presence of a chemistry similar to silicon oxynitride at the two-grain junctions, which may be due to partial dissolution of nitrogen in the grain-boundary film. The chemical composition of the grain-boundary film was SiN_xO_y, (x ∼ 0.53 and y ∼ 1.23), and the triple pocket corresponded to the amorphous SiO₂ containing ∼2 wt% nitrogen. The equilibrium grain-boundary-film thickness was measured and found to be smaller for the material with the lower oxygen content. This difference in thickness has been explained by the presence of the relatively larger calcium concentration in the material with the lower amount of SiO₂ grain-boundary phase, because the concentration of foreign ions has been shown to affect the grain-boundary thickness.     

Microstructure and Property Characterization of Sintered Si3N4, SiC, and SiAlON

Commercially produced pressureless sintered Si₃N₄, SiC, and SiAlON were characterized with respect to density, phases present, bend strength, and oxidation resistance. The room-temperature bend strengths of sintered Si₃N₄, SiC, and SiAlON are comparable. However, the room-temperature strengths are much lower (=40 to 50%) than the room-temperature strength of hot–pressed Si₃N₄ (NC-132). The strength loss in Si₃N₄ and SiAlON materials at high temperature was attributed to a viscous grain-boundary phase retained during cooling from the sintering temperature. The oxidation resistance of sintered a-SiC was the best of any materials tested.     

Highly Transparent Lu-α-SiAlON

Novel Lu-α-SiAlON ceramics were produced by hot pressing mixtures of Si₃N₄, Lu₂O₃, AlN, and Al₂O₃ at 1950°C for 2 h in a nitrogen atmosphere. The resultant SiAlON was fully dense and possessed a uniform, equiaxed microstructure with a grain size of ∼1 μm, which resulted in a high hardness of >19 GPa. In addition to high hardness, the sample showed very high optical transparency in the visible light region, with >70% transmission at higher wavelengths. This high transparency was attributed to the uniform, dense microstructure and lack of residual grain-boundary phase.     

Local Viscosity of Si-O-C-N Nanoscale Amorphous Phases at Ceramic Grain Boundaries

Internal friction characterization has been used to quantitatively assess the viscosity characteristics of Si-O-C-N glasses segregated to nanometer-sized grain boundaries of polycrystalline Si₃N₄ and SiC ceramics. A relaxation peak of internal friction, which arises with rising temperature from the viscous sliding of glassy grain boundaries, was systematically collected and analyzed with respect to its shift upon changing the oscillation frequency. As a result of such an analysis, both activation energy for viscous grain-boundary flow and inherent viscosity of the intergranular glass film could be quantitatively evaluated. Two main features are shown: (i) the presence of N and/or C greatly affects the viscosity characteristics of SiO₂ phases at Si₃N₄ and SiC grain boundaries; and (ii) the internal friction method has potential as a unique experimental tool for understanding the local properties of nanoscale amorphous phases in new ceramic materials.     

Oxidation Behavior of Liquid-Phase Sintered Silicon Carbide with Aluminum Nitride and Rare-Earth Oxides (Re2O3, where Re = Y, Er, Yb)

Silicon carbide (SiC) ceramics have been fabricated by hot-pressing and subsequent annealing under pressure with aluminum nitride (AlN) and rare-earth oxides (Y₂O₃, Er₂O₃, and Yb₂O₃) as sintering additives. The oxidation behavior of the SiC ceramics in air was characterized and compared with that of the SiC ceramics with yttrium–aluminum–garnet (YAG) and Al₂O₃–Y₂O₃–CaO (AYC). All SiC ceramics investigated herein showed a parabolic weight gain with oxidation time at 1400°C. The SiC ceramics sintered with AlN and rare-earth oxides showed superior oxidation resistance to those with YAG and Al₂O₃–Y₂O₃–CaO. SiC ceramics with AlN and Yb₂O₃ showed the best oxidation resistance of 0.4748 mg/cm² after oxidation at 1400°C for 192 h. The minimization of aluminum in the sintering additives was postulated as the prime factor contributing to the superior oxidation resistance of the resulting ceramics. A small cationic radius of rare-earth oxides, dissolution of nitrogen to the intergranular glassy film, and formation of disilicate crystalline phase as an oxidation product could also contribute to the superior oxidation resistance.     

Microstructure of 96% Alumina Ceramics: I, Characterization of the As-Sintered Materials

Characterization of the microstructure and microchemistry of a group of commercial 96% Al₂O₃ ceramics, using analytical and conventional electron microscopy techniques, was conducted. A continuous glassy grain-boundary phase was found in all samples, in addition to a number of intragranular and intergranular crystalline second phases; the phases present depended on the original boundary-glass composition. The faceted nature of many of the Al₂O₃-glass interfaces was studied and is thought to be an equilibrium structure.     

In Situ Synthesis of Ultrafine ZrB2–SiC Composite Powders and the Pressureless Sintering Behaviors

Ultrafine ZrB₂–SiC composite powders have been synthesized in situ using carbothermal reduction reactions via the sol–gel method at 1500°C for 1 h. The powders synthesized had a relatively smaller average crystallite size (<200 nm), a larger specific surface area (∼20 m²/g), and a lower oxygen content (∼1.0 wt %). Composites of ZrB₂+20 wt% SiC were pressureless sintered to ∼96.6% theoretical density at 2250°C for 2 h under an argon atmosphere using B₄C and Mo as sintering aids. Vickers hardness and flexural strength of the sintered ceramic composites were 13.9±0.3 GPa and 294±14 MPa, respectively. The microstructure of the composites revealed that elongated SiC grain dispersed uniformly in the ZrB₂ matrix. Oxidation from 1100° to 1600°C for 30 min showed no decrease in strength below 1400°C but considerable decrease in strength with a rapid weight increment was observed above 1500°C. The formation of a protective borosilicate glassy coating appeared at 1400°C and was gradually destroyed in the form of bubble at higher temperatures.     

Microstructure, Microchemistry, and Flexural Strength of Mullite Ceramics

The microstructure of mullite ceramics hot-pressed and sintered at different temperatures was studied using transmission electron microscopy (TEM) with energy dispersive spectroscopy (EDS), scanning electron microscopy (SEM) with EDS, and electron probe microanalysis (EPMA). The specimens, consisting of stoichiometric mullite grains without glassy phase, are obtained by hot-pressing stoichiometric mullite powder at 1575°C for 1 h. Silica-rich glassy phases are observed using TEM at three-grain junctions of mullite grains in specimens heated at and above 1600°C. However, high-resolution transmission electron micrographs show no glassy phase at two-grain boundaries in all specimens. SEM with EDS analyses show that the average value of Al₂O₃ contents of mullite grains increases slightly with increasing temperature. These results are consistent with a published Al₂O₃–SiO₂ phase diagram. The flexural strength of mullite specimens at room temperature depends on their microstructure, such as the grain size and grain size distribution of mullite grains. The strength is high at room temperature and up to 1200°C, and it decreases at and above 1350°C, irrespective of the presence of the glassy phase.     

Mechanical Properties of Infiltrated Alumina-Y-TZP Composites

Small Al₂O₃ additions (∼ 4 vol%) made to Y-TZP using an infiltration technique increased the fracture toughness and strength by ∼15% and the amount of transgranular fracture. Ionic conductivity measurements showed decreased grain-boundary conductivity, confirming a change in the grain-boundary composition. The predominant failure origins for both the unmodified Y-TZP and the Al₂O₃—Y-TZP were surface flaws related to agglomerates in the original powder. Finishing reduced the severity of these flaws and substantially increased the strength of both materials (>50%). The infiltration approach introduced a new flaw population in some specimens; however, this problem was overcome by a simple processing modification.