Enhanced Device Performance of Perovskite Photovoltaics by Magnetic Field‐Aligned Perovskites‐Magnetic Nanoparticles Composite Thin Film

Perovskite photovoltaics have drawn great attention in both academic and industrial sectors in the past decade. To date, impressive device performance has been achieved in state‐of‐the‐art device architectures through morphological manipulation and generic interface engineering. In this study, enhanced device performance of perovskite photovoltaics by magnetic field‐aligned CH₃NH₃PbI₃‐mixed Fe₃O₄ magnetic nanoparticles (CH₃NH₃PbI₃:Fe₃O₄) composite thin films is reported. It is found that magnetic field‐aligned CH₃NH₃PbI₃:Fe₃O₄ composite thin films possess superior film morphology, boosted and balanced charge carrier mobility, and suppressed trap density. Moreover, perovskite photovoltaics by magnetic field‐aligned CH₃NH₃PbI₃:Fe₃O₄ composite thin films exhibit suppressed charge carrier recombination and shorter charge carrier extraction time. As a result, perovskite solar cells by magnetic field‐aligned CH₃NH₃PbI₃:Fe₃O₄ composite thin films exhibit 20.23% power conversion efficiency with significantly reduced photocurrent hysteresis. Moreover, perovskite photodetectors by magnetic field‐aligned CH₃NH₃PbI₃:Fe₃O₄ composite thin films exhibit a photoresponsivity of 858 mA W^?1, a photodetectivity over 10¹³ Jones (1 Jones = 1 cm Hz^1/2 W^?1) and a linear dynamic range over 160 dB at room temperature. All these device performance parameters are significantly better than those by pristine CH₃NH₃PbI₃ thin film. Thus, these studies provide a facile way to boost device performance of perovskite photovoltaics.     

Electron‐Transport‐Layer‐Assisted Crystallization of Perovskite Films for High‐Efficiency Planar Heterojunction Solar Cells

Crystal engineering of CH₃NH₃PbI₃ perovskite materials through template‐directed nucleation and growth on PbI₂ nuclei dispersed in a polar fullerene (C₆₀ pyrrolidine tris‐acid, CPTA) electron transport layer (ETL) (CPTA:PbI₂) is proposed as a route for controlling crystallization kinetics and grain sizes. Chemical analysis of the CPTA:PbI₂ template confirms that CPTA carboxylic acid groups can form a monodentate or bidentate chelate with Pb(II), resulting in a lower nucleation barrier that promotes rapid formation of the tetragonal perovskite phase. Moreover, it is demonstrated that a uniform CH₃NH₃PbI₃ film with highly crystalline and large domain sizes can be realized by increasing the spacing between nuclei to retard perovskite crystal growth via careful control of the preferred nucleation site distribution in the CPTA:PbI₂ layer. The improved perovskite morphology possesses a long photoluminescence lifetime and efficient photocarrier transport/separation properties to eliminate the hysteresis effect. The corresponding planar heterojunction photovoltaic yields a high power conversion efficiency (PCE) of 20.20%, with a high fill factor (FF) of 81.13%. The average PCE and FF values for 30 devices are 19.03% ± 0.57% and 78.67% ± 2.13%, respectively. The results indicate that this ETL template‐assisted crystallization strategy can be applied to other organometal halide perovskite‐based systems.     

Efficient Perovskite Hybrid Photovoltaics via Alcohol‐Vapor Annealing Treatment

In this work, alcohol‐vapor solvent annealing treatment on CH₃NH₃PbI₃ thin films is reported, aiming to improve the crystal growth and increase the grain size of the CH₃NH₃PbI₃ crystal, thus boosting the performance of perovskite photovoltaics. By selectively controlling the CH₃NH₃I precursor, larger‐grain size, higher crystallinity, and pinhole‐free CH₃NH₃PbI₃ thin films are realized, which result in enhanced charge carrier diffusion length, decreased charge carrier recombination, and suppressed dark currents. As a result, over 43% enhanced efficiency along with high reproducibility and eliminated photocurrent hysteresis behavior are observed from perovskite hybrid solar cells (pero‐HSCs) where the CH₃NH₃PbI₃ thin films are treated by methanol vapor as compared with that of pristine pero‐HSCs where the CH₃NH₃PbI₃ thin films are without any alcohol vapor treatment. In addition, the dramatically restrained dark currents and raised photocurrents give rise to over ten times enhanced detectivities for perovskite hybrid photodetectors, reaching over 10¹³ cm Hz^1/2 W^?1 (Jones) from 375 to 800 nm. These results demonstrate that the method provides a simple and facile way to boost the device performance of perovskite photovoltaics.     

Synergistic Effect of PbI2 Passivation and Chlorine Inclusion Yielding High Open‐Circuit Voltage Exceeding 1.15 V in Both Mesoscopic and Inverted Planar CH3NH3PbI3(Cl)‐Based Perovskite Solar Cells

Enhancing open‐circuit voltage in CH₃NH₃PbI₃(Cl) perovskite solar cells has become a major challenge for approaching the theoretical limit of the power conversion efficiency. Here, for the first time, it is demonstrated that the synergistic effect of PbI₂ passivation and chlorine incorporation via controlling the molar ratio of PbI₂, PbCl₂ (or MACl), and MAI in the precursor solutions, boosts the open‐circuit voltage of CH₃NH₃PbI₃(Cl) perovskite solar cells over 1.15 V in both mesoscopic and inverted planar perovskite solar cells. Such high open‐circuit voltage can be attributed to the enhanced photoluminescence emission and carrier lifetime associated with the reduced trap densities. The morphology and composition analysis using scanning electron microscopy, X‐ray diffraction measurements, and energy dispersive X‐ray spectroscopy confirm the high quality of the optimized CH₃NH₃PbI₃(Cl) perovskite film. On this basis, record‐high efficiencies of 16.6% for nonmetal‐electrode all‐solution‐processed perovskite solar cells and 18.4% for inverted planar perovskite solar cells are achieved.     

In situ recycle of PbI2 as a step towards sustainable perovskite solar cells

The development of organometal halide perovskite solar cells has grown rapidly and the highest efficiency of the devices has recently surpassed 22%. Because these solar cells contain toxic lead, a sustainable strategy is required to prevent environmental pollution and avoid healthy hazard caused by possible lead outflow. Here, in situ recycling PbI₂ from thermal decomposition CH₃NH₃PbI₃ perovskite films for efficient perovskite solar cells was developed. The thermal behavior of CH₃NH₃PbI₃ perovskite and its individual components were examined by thermogravimetric analysis. By optimizing the process of thermal decomposition CH₃NH₃PbI₃ film, the complete conversion from CH₃NH₃PbI₃ to pure PbI₂ layer with a mesoporous scaffold was achieved. The mesoporous structure readily promotes the conversion efficiency of perovskite and consequently results in high‐performance device. A perovskite crystal growth mechanism on the mesoporous PbI₂ structure was proposed. These results suggest that in situ recycled PbI₂ scaffolds can be a new route in manipulating the morphology of the perovskite active layer, providing new possibilities for high performance. Meanwhile, the risk of lead outflow can be released, and the saving‐energy fabrication of efficient solar cells can be realized.     

Improved morphology and enhanced stability via solvent engineering for planar heterojunction perovskite solar cells

Solvent engineering technique for planar heterojunction perovskite solar cells is an efficient way to achieve uniformly controlled grain morphology for perovskite films. In this report, diethyl ether solvent engineering technique was used for Methyl ammonium lead triiodide (CH₃NH₃PbI₃) perovskite thin films for planar heterojunction solar cells which exhibited a PCE of 9.20%. Morphological improvements and enhanced grain sizes leads to enhanced absorption of CH₃NH₃PbI₃. Moreover solar cells have showed an excellent environmental stability of more than 100 days. This increase in efficiency is due to improved film morphology of perovskite layer after solvent treatment which has been revealed under UV–Vis spectroscopy, SEM images, X-ray diffraction and impedance spectroscopy.     

Morphological Control for High Performance,Solution‐Processed Planar Heterojunction Perovskite Solar Cells

Organometal trihalide perovskite based solar cells have exhibited the highest efficiencies to‐date when incorporated into mesostructured composites. However, thin solid films of a perovskite absorber should be capable of operating at the highest efficiency in a simple planar heterojunction configuration. Here, it is shown that film morphology is a critical issue in planar heterojunction CH₃NH₃PbI_3‐xCl_x solar cells. The morphology is carefully controlled by varying processing conditions, and it is demonstrated that the highest photocurrents are attainable only with the highest perovskite surface coverages. With optimized solution based film formation, power conversion efficiencies of up to 11.4% are achieved, the first report of efficiencies above 10% in fully thin‐film solution processed perovskite solar cells with no mesoporous layer.     

Viscosity effect of ionic liquid-assisted controlled growth of CH3NH3PbI3 nanoparticle-based planar perovskite solar cells

A precise control of the morphology and crystallization of perovskite thin-films is well-correlated to higher perovskite solar cells performances. Ionic liquids (ILs) can retard perovskite crystallization to aid the formation of films with uniform morphology to realize highly efficient perovskite solar cells. Herein, we attempt to control the nanostructural growth of CH₃NH₃PbI₃ thin films by adding ILs to the perovskite spin-coating solution and investigate the effect of IL viscosity on the resulting CH₃NH₃PbI₃ nanoparticle (NP) thin films. NPs with desirable morphology were obtained using ILs with a low viscosity that completely dissolved in the CH₃NH₃PbI₃ solution. In particular, the IL tetrabutylammonium chloride yielded NPs with a diameter of 500 nm and controllable morphology, crystallinity, and absorption behavior, which led to improved photovoltaic performance compared with that of solar cells containing NPs produced using other ILs. Our findings revealed a pathway to obtain uniformly distributed CH₃NH₃PbI₃ NP thin films for use in perovskite solar cells. The developed method is well suited for large-scale production of perovskite thin films on flexible substrates.     

High‐Performance Planar Solar Cells Based On CH3NH3PbI3‐xClx Perovskites with Determined Chlorine Mole Fraction

Solution‐processable hybrid perovskite solar cells are a new member of next generation photovoltaics. In the present work, a low‐temperature two‐step dipping method is proposed for the fabrication of CH₃NH₃PbI_3‐xCl_x perovskite films on the indium tin oxide glass/poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) substrate. The bandgaps of the CH₃NH₃PbI_3‐xCl_x perovskite films are tuned in the range between 1.54 and 1.59 eV by adjusting the PbCl₂ mole fraction (n_Cl/(n_Cl + n_I)) in the initial mixed precursor solution from 0.10 to 0.40. The maximum chlorine mole fraction measured by a unique potentiometric titration method in the produced CH₃NH₃PbI_3‐xCl_x films can be up to 0.220 ± 0.020 (x = 0.660 ± 0.060), which is much higher than that produced by a one‐step spin‐coating method (0.056 ± 0.015, x = 0.17 ± 0.04). The corresponding solar cell with the CH₃NH₃PbI_2.34±0.06Cl_0.66±0.06 perovskite film sandwiched between PEDOT:PSS and C₆₀ layers exhibits a power conversion efficiency as high as 14.5%. Meanwhile, the open‐circuit potential (V_oc) of the device reaches 1.11 V, which is the highest V_oc reported in the perovskite solar cells fabricated on PEDOT:PSS so far.     

Probing Molecular and Crystalline Orientation in Solution‐Processed Perovskite Solar Cells

The microstructure of solution‐processed organometallic lead halide perovskite thin films prepared by the “gas‐assisted” method is investigated with synchrotron‐based techniques. Using a combination of GIWAXS and NEXAFS spectroscopy the orientational alignment of CH₃NH₃PbI₃ crystallites and CH₃NH₃⁺ cations are separately probed. The GIWAXS results reveal a lack of preferential orientation of CH₃NH₃PbI₃ crystallites in 200–250 nm thick films prepared on both planar TiO₂ and mesoporous TiO₂. Relatively high efficiencies are observed for device based on such films, with 14.3% achieved for planar devices and 12% for mesoporous devices suggesting that highly oriented crystallites are not crucial for good cell performance. Oriented crystallites however are observed in thinner films (≈60 nm) deposited on planar TiO₂ (but not on mesoporous TiO₂) indicating that the formation of oriented crystallites is sensitive to the kinetics of solvent evaporation and the underlying TiO₂ morphology. NEXAFS measurements on all samples found that CH₃NH₃⁺ cations exhibit a random molecular orientation with respect to the substrate. The lack of any NEXAFS dichroism for the thin CH₃NH₃PbI₃ layer deposited on planar TiO₂ in particular indicates the absence of any preferential orientation of CH₃NH₃⁺ cations within the CH₃NH₃PbI₃ unit cell for as‐prepared layers, that is, without any electrical poling.     

Efficient and non-hysteresis CH3NH3PbI3/PCBM planar heterojunction solar cells

Highly efficient and non-hysteresis organic/perovskite planar heterojunction solar cells was fabricated by low-temperature, solution-processed method with a structure of ITO/PEDOT:PSS/CH₃NH₃PbI₃/PCBM/Al. The high-quality perovskite thin film was obtained using a solvent-induced-fast-crystallization deposition involving spin-coating the CH₃NH₃PbI₃ solution followed by top-dropping chlorobenzene with an accurate control to induce the crystallization, which results in highly crystalline, pinhole-free, and smooth perovskite thin film. Furthermore, it was found that the molar ratio of CH₃NH₃I to PbI₂ greatly influence the properties of CH₃NH₃PbI₃ film and the device performance. The equimolar or excess PbI₂ was facile to form a flat CH₃NH₃PbI₃ film and produced relatively uniform perovskite crystals. Perovskite solar cells (PSCs) with high-quality CH₃NH₃PbI₃ thin film showed good performance and excellent repeatability. The power conversion efficiency (PCE) up to 13.49% was achieved, which is one of the highest PCEs obtained for low-temperature, solution-processed planar perovskite solar cells based on the structure ITO/PEDOT:PSS/CH₃NH₃PbI₃/PC₆₁BM/Al. More importantly, PSCs fabricated using this method didn’t show obvious hysteresis under different scan direction and speed.     

利用偏钨酸铵的DMF/水溶液旋涂热解制备WO3薄膜及其在钙钛矿太阳电池致密层中的应用

本文首次通过旋涂热解偏钨酸铵((NH₄)₆H₂W₁₂O₄₀)的DMF/水溶液成功制备了致密的三氧化钨(WO₃)薄膜, 系统研究了WO₃薄膜厚度及用异丙醇冲洗处理气相辅助溶液法制备的CH₃NH₃PbI₃薄膜对相应钙钛矿太阳电池光伏性能的影响. 结果表明, 使用厚度为62nmWO₃致密层的平板钙钛矿太阳电池获得了短路电流密度17.39 mA.cm_-2, 开路电压0.58 V, 填充因子0.57, 相应光电转化效率5.72%. 使用异丙醇冲洗CH₃NH₃PbI₃薄膜后, 相应太阳电池的光电转化效率由5.72 % 升高到7.04 %.     

Efficient lead acetate sourced planar heterojunction perovskite solar cells with enhanced substrate coverage via one-step spin-coating

In planar heterojunction (PHJ) perovskite solar cells (PerSCs) without mesoporous metal oxide skeleton, there is challenge of formation perovskite film with full coverage to the conductive substrate through solution-process the lead halide precursors. Selecting a lead source with more volatile byproducts is an effective approach to obtain much smoother films with smaller and fewer pinholes. Herein, we demonstrate efficient CH₃NH₃PbI₃/PCBM PHJ PerSCs by using lead acetate (Pb(Ac)₂) as lead precursor. The morphology of the perovskite thin films were investigated by scanning electron microscopy (SEM) and atomic force microscopy (AFM), respectively, and the crystalline quality of the perovskite films were investigated by X-ray diffraction (XRD) spectroscopy. Time-resolved photoluminescence (TRPL) was used to investigate the PL lifetime of the perovskite film. The perovskite film derived from Pb(Ac)₂ shows enhanced surface coverage and improved photoluminescence lifetime in comparison with PbI₂ sourced perovskite film. Averaged over 20 individual devices, the power conversion efficiency (PCE) of devices derived from Pb(Ac)₂ reaches 14.81%, much higher than PbI₂ sourced devices by one-step (8.23%) or two-step (10.58%) spin-coating.     

High-quality CH3NH3PbI3 thin film fabricated via intramolecular exchange for efficient planar heterojunction perovskite solar cells

The high-quality CH₃NH₃PbI₃ perovskite thin film with excellent coverage and uniformity was prepared using an intramolecular exchange technology via a low-temperature, two-step sequential deposition process. The PbI₂(DMSO) complex was synthesized at room temperature without any additives and was deposited, then the CH₃NH₃I solution was deposited subsequently. The further controllable thermal annealing process resulted in the complete formation of flat and uniform CH₃NH₃PbI₃ thin film with large-size grains and (110) preferred crystallographic orientation. The perovskite solar cells (PSCs) with a very simple inverted planar heterojunction structure of ITO/PEDOT:PSS/CH₃NH₃PbI₃/PCBM/Al and without other buffer layers, e.g., C₆₀, LiF, BCP, etc., were fabricated, resulting in a power conversion efficiency (PCE) as high as 14.26%. The results suggest that the low-temperature, two-step sequential deposition process with intramolecular exchange technology provides a good route to fabricate high-quality perovskite thin film and efficient PSCs, which would match with large-scale, high-output roll-to-roll (R2R) printing/coating techniques.     

Enhancing the Optoelectronic Performance of Perovskite Solar Cells via a Textured CH3NH3PbI3 Morphology

Perovskite‐based solar cells are generally assembled as planar structures comprising a flat organoammonium metal halide perovskite layer, or mesoscopic structures employing a mesoporous metal‐oxide scaffold into which the perovskite material is infiltrated. To present, little attention has been directed toward the texturing of the perovskite material itself. Herein, a textured CH₃NH₃PbI₃ morphology formed through a thin mesoporous TiO₂ seeding layer and a gas‐assisted crystallization method is reported. The textured morphology comprises a multitiered nanostructure, which allows for significant improvements in the light harvesting and charge extraction performance of the solar cells. Due to these improvements, average short‐circuit current densities for a batch of 28 devices are in excess of 22 mA cm^?2, and the maximum recorded power conversion efficiency is 16.3%. The performance gains concomitant with this textured CH₃NH₃PbI₃ morphology provide further insights into how control of the perovskite microstructure can be used to enhance the cell performance.     

A promising unisource thermal evaporation for in situ fabrication of organolead halide perovskite CH3NH3PbI3 thin film

In this work, a new method of fabricating organolead halide perovskite CH₃NH₃PbI₃ thin film by unisource thermal evaporation was proposed, which ensured high‐quality film with composition, crystal‐structure homogeneity, full surface coverage, well‐defined grain structure, high crystalline, and reproducibility, suggesting its promising applicability for significant optimization in efficient. Copyright © 2015 John Wiley & Sons, Ltd.     

Reduced Defects of MAPbI3 Thin Films Treated by FAI for High‐Performance Planar Perovskite Solar Cells

Organolead trihalide perovskite films with a large grain size and excellent surface morphology are favored to good‐performance solar cells. However, interstitial and antisite defects related trap‐states are originated unavoidably on the surfaces of the perovskite films prepared by the solution deposition procedures. The development of post‐growth treatment of defective films is an attractive method to reduce the defects to form good‐quality perovskite layers. Herein, a post‐treatment tactic is developed to optimize the perovskite crystallization by treating the surface of the one‐step deposited CH₃NH₃PbI₃ (MAPbI₃) using formamidinium iodide (FAI). Charge carrier kinetics investigated via time‐resolved photoluminescent, open‐circuit photovoltage decay, and time‐resolved charge extraction indicate that FAI post‐treatment will boost the perovskite crystalline quality, and further result in the reduction of the defects or trap‐states in the perovskite films. The photovoltaic devices by FAI treatment show much improved performance in comparison to the controlled solar cell. As a result, a champion solar cell with the best power conversion efficiency of 20.25% is obtained due to a noticeable improvement in fill factor. This finding exhibits a simple procedure to passivate the perovskite layer via regulating the crystallization and decreasing defect density.     

Improving the Extraction of Photogenerated Electrons with SnO2 Nanocolloids for Efficient Planar Perovskite Solar Cells

Great attention to cost‐effective high‐efficiency solar power conversion of trihalide perovskite solar cells (PSCs) has been hovering at high levels in the recent 5 years. Among PSC devices, admittedly, TiO₂ is the most widely used electron transport layer (ETL); however, its low mobility which is even less than that of CH₃NH₃PbI₃ makes it not an ideal material. In principle, SnO₂ with higher electron mobility can be regarded as a positive alternative. Herein, a SnO₂ nanocolloid sol with ≈3 nm in size synthesized at 60 °C was spin‐coated onto the fuorine‐doped tin oxide (FTO) glass as the ETL of planar CH₃NH₃PbI₃ perovskite solar cells. TiCl₄ treatment of SnO₂‐coated FTO is found to improve crystallization and increase the surface coverage of perovskites, which plays a pivotal role in improving the power conversion efficiency (PCE). In this report, a champion efficiency of 14.69% (J_sc = 21.19 mA cm^?2, V_oc = 1023 mV, and FF = 0.678) is obtained with a metal mask at one sun illumination (AM 1.5G, 100 mW cm^?2). Compared to the typical TiO₂, the SnO₂ ETL efficiently facilitates the separation and transportation of photogenerated electrons/holes from the perovskite absorber, which results in a significant enhancement of photocurrent and PCE.     

Precursor Solution Annealing Forms Cubic‐Phase Perovskite and Improves Humidity Resistance of Solar Cells

Solar cells with light‐absorbing layers comprising organometal halide perovskites have recently exceeded 22% efficiency. Despite high power‐conversion efficiencies, the stability of these devices, particularly when exposed to humidity and oxygen, remains poor. In the current study, a pathway to increase the stability of methylammonium lead iodide (CH₃NH₃PbI₃) based solar cells towards humidity is demonstrated, while maintaining the simplicity and solution‐processability of the active layers. Thermal annealing of the precursor solution prior to deposition induces the formation of cubic‐phase perovskite films in the solid state at room temperature. The experiments demonstrate that this improved ambient stability is correlated with the presence of the cubic phase at device operating temperatures, with the cubic phase resisting the formation of perovskite monohydrate—a pathway of degradation in conventionally processed perovskite thin films—on exposure to humidity.     

High‐Performance Photodetectors Based on Organometal Halide Perovskite Nanonets

The booming development of organometal halide perovskites has prompted the exploration of morphology‐engineering strategies to improve their performance in optoelectronic applications. However, the preparation of optoelectronic devices of perovskites with complex architectures and desirable properties is still highly challenging. Herein, novel CH₃NH₃PbI₃ nanonets and nanobowl arrays are fabricated facilely by using monolayer colloidal crystal (MCC) templates on different substrates. Specifically, highly ordered CH₃NH₃PbI₃ nanonets with high crystallinity are fabricated on a variety of flat substrates, whereas regular CH₃NH₃PbI₃ nanobowl arrays are produced on a coarse substrate. The photodetection performance of the CH₃NH₃PbI₃ nanonet‐based photodetectors is significantly enhanced compared to the photodetectors based on conventional CH₃NH₃PbI₃ compact films. Particularly, the nanonet photodetectors exhibit a high responsivity (10.33 A W^?1 under 700 nm monochromatic light), which is six times higher than that for the compact CH₃NH₃PbI₃ film devices, fast response speed, and good stability. Owing to the two‐dimensional arrayed structure, the CH₃NH₃PbI₃ nanonets exhibit an enhanced light harvesting ability and offer direct carrier transport pathways. Meanwhile, the MCC template brings about larger grain sizes with enhanced crystallinity. Furthermore, the perovskite nanonets can be formed on a flexible polyethylene terephthalate substrate for the fabrication of promising flexible nanonet photodetectors.