Trimetallic Mn‐Fe‐Ni Oxide Nanoparticles Supported on Multi‐Walled Carbon Nanotubes as High‐Performance Bifunctional ORR/OER Electrocatalyst in Alkaline Media

Discovering precious metal‐free electrocatalysts exhibiting high activity and stability toward both the oxygen reduction (ORR) and the oxygen evolution (OER) reactions remains one of the main challenges for the development of reversible oxygen electrodes in rechargeable metal–air batteries and reversible electrolyzer/fuel cell systems. Herein, a highly active OER catalyst, Fe_0.3Ni_0.7O_X supported on oxygen‐functionalized multi‐walled carbon nanotubes, is substantially activated into a bifunctional ORR/OER catalyst by means of additional incorporation of MnO_X. The carbon nanotube‐supported trimetallic (Mn‐Ni‐Fe) oxide catalyst achieves remarkably low ORR and OER overpotentials with a low reversible ORR/OER overvoltage of only 0.73 V, as well as selective reduction of O₂ predominantly to OH^?. It is shown by means of rotating disk electrode and rotating ring disk electrode voltammetry that the combination of earth‐abundant transition metal oxides leads to strong synergistic interactions modulating catalytic activity. The applicability of the prepared catalyst for reversible ORR/OER electrocatalysis is evaluated by means of a four‐electrode configuration cell assembly comprising an integrated two‐layer bifunctional ORR/OER electrode system with the individual layers dedicated for the ORR and the OER to prevent deactivation of the ORR activity as commonly observed in single‐layer bifunctional ORR/OER electrodes after OER polarization.     

Extreme‐Performance Rubber Nanocomposites for Probing and Excavating Deep Oil Resources Using Multi‐Walled Carbon Nanotubes

The scarcity of oil resources is going to become one of the main factors threatening the stability of the global economy. To avoid an energy crisis in the future, it is essential to increase oil extraction in much deeper wells, experiencing higher temperatures and pressures. Exploring these deeper areas will demand novel and robust materials. Rubber sealants, or O‐rings, are especially key components in enabling the probing and production of oil in deeper wells, so that higher temperature and pressure reservoirs are reached. In this account, it is demonstrated that carbon nanotubes homogeneously and randomly dispersed in rubber matrices, are able to generate durable sealants that operate satisfactorily at extremely high temperatures and pressures (e.g., 260 °C and 239 MPa). The key issues in these novel composites are: i) the nanotube surface‐control and reactivity, ii) the used of multi‐walled carbon nanotubes (MWNTs)‐embedded in fluorinated rubber, and iii) the formation of a cellulation structure. This rubber nanocomposite with a cellulation structure and having extreme performance leads to a balanced pressure resistance, sealing ability, thermal resistance, and durability, which can contribute to doubling the current average global oil recovery efficiency.     

Open‐Ended,N‐Doped Carbon Nanotube–Graphene Hybrid Nanostructures as High‐Performance Catalyst Support

A hierarchical N‐doped carbon nanotube‐graphene hybrid nanostructure (NCNT‐GHN), in which the graphene layers are distributed inside the CNT inner cavities, was designed to efficiently support noble metal (e.g., PtRu) nanoparticles. Well‐dispersed PtRu nanoparticles with diameters of 2–4 nm were immobilized onto these NCNT‐GHN supports by a low‐temperature chemical reduction method without any pretreatment. Compared to conventional CNTs and commercial catalysts. a much better catalytic performance was achieved by a synergistic effect of the hierarchical structure (graphene‐CNT hybrid) and electronic modulation (N‐doping) during the methanol electrooxidation reaction. Improved single‐cell performances with long‐term stability are also demonstrated using NCNT‐GHN as catalyst support.     

Electrochemical Properties of High‐Power Supercapacitors Using Single‐Walled Carbon Nanotube Electrodes

We have investigated the key factors determining the performance of supercapacitors constructed using single‐walled carbon nanotube (SWNT) electrodes. Several parameters, such as composition of the binder, annealing temperature, type of current collector, charging time, and discharging current density have been optimized for the best performance of the supercapacitor with respect to energy density and power density. We find a maximum specific capacitance of 180 F/g and a measured power density of 20 kW/kg at energy densities in the range from 7 to 6.5 Wh/kg at 0.9 V in a solution of 7.5 N KOH (the currently available supercapacitors have energy densities in the range 6–7 Wh/kg and power density in the range 0.2–5 kW/kg at 2.3 V in non‐aqueous solvents).     

Current‐Induced Restructuring and Chemical Modification of N‐Doped Multi‐walled Carbon Nanotubes

Multi‐walled carbon nanotubes (MWCNTs) have long been anticipated as candidates for electrical components in an increasingly miniaturized electronics industry due to their inherent electrical properties. It is possible to manipulate and control these properties by introducing dopants such as N, B, and P. Although some current‐induced structural changes in MWCNTs have been observed, no systematic study has been carried out to explore the correlation of changes in the internal structure with the electronic behavior of doped‐MWCNTs in terms of the current densities present. In situ transmission electron microscopy (TEM) investigations are presented here of individual, N‐doped MWNCT (N‐MWCNTs) using the in situ TEM/scanning tunneling microscopy (TEM/STM) Nanofactory© holder. It is observed for the first time that N‐MWCNTs not only undergo current‐induced structural transformation; i.e., from the typical bamboo structure of N‐MWCNTs to the stacked cones, but also—and most importantly—the complete removal of the dopant causes a significant change in the electronic behavior. This has serious implications for the use of doped CNTs as electronic components, especially since tremendous efforts are being made to synthesize CNTs with controlled dopant concentrations.     

Spray‐Layer‐by‐Layer Carbon Nanotube/Electrospun Fiber Electrodes for Flexible Chemiresistive Sensor Applications

Development of a versatile method for incorporating conductive materials into textiles could enable advances in wearable electronics and smart textiles. One area of critical importance is the detection of chemicals in the environment for security and industrial process monitoring. Here, the fabrication of a flexible, sensor material based on functionalized multi‐walled carbon nanotube (MWNT) films on a porous electrospun fiber mat for real‐time detection of a nerve agent simulant is reported. The material is constructed by layer‐by‐layer (LbL) assembly of MWNTs with opposite charges, creating multilayer films of MWNTs without binder. The vacuum‐assisted spray‐LbL process enables conformal coatings of nanostructured MWNT films on individual electrospun fibers throughout the bulk of the mat with controlled loading and electrical conductivity. A thiourea‐based receptor is covalently attached to the primary amine groups on the MWNT films to enhance the sensing response to dimethyl methylphosphonate (DMMP), a simulant for sarin nerve agent. Chemiresistive sensors based on the engineered textiles display reversible responses and detection limits for DMMP as low as 10 ppb in the aqueous phase and 5 ppm in the vapor phase. This fabrication technique provides a versatile and easily scalable strategy for incorporating conformal MWNT films into three‐dimensional substrates for numerous applications.     

Ultrathin MnO2/Graphene Oxide/Carbon Nanotube Interlayer as Efficient Polysulfide‐Trapping Shield for High‐Performance Li–S Batteries

Ultrathin MnO₂/graphene oxide/carbon nanotube (G/M@CNT) interlayers are developed as efficient polysulfide‐trapping shields for high‐performance Li–S batteries. A simple layer‐by‐layer procedure is used to construct a sandwiched vein–membrane interlayer of thickness 2 µm and areal density 0.104 mg cm^?2 by loading MnO₂ nanoparticles and graphene oxide (GO) sheets on superaligned carbon nanotube films. The G/M@CNT interlayer provides a physical shield against both polysulfide shuttling and chemical adsorption of polysulfides by MnO₂ nanoparticles and GO sheets. The synergetic effect of the G/M@CNT interlayer enables the production of Li–S cells with high sulfur loadings (60–80 wt%), a low capacity decay rate (?0.029% per cycle over 2500 cycles at 1 C), high rate performance (747 mA h g^?1 at a charge rate of 10 C), and a low self‐discharge rate with high capacity retention (93.0% after 20 d rest). Electrochemical impedance spectroscopy, cyclic voltammetry, and scanning electron microscopy observations of the Li anodes after cycling confirm the polysulfide‐trapping ability of the G/M@CNT interlayer and show its potential in developing high‐performance Li–S batteries.     

Microwave‐Induced Controlled Purification of Single‐Walled Carbon Nanotubes without Sidewall Functionalization

A microwave‐induced controlled method for the purification of single‐walled carbon nanotubes (SWCNTs) by removing residual metal catalysts and carbonaceous impurities is reported. Compared to conventional strong acid treatment, this one‐step method uses dilute acids and complexing agents and reduces the reaction times to the order of minutes. Furthermore, the SWCNTs retain their chemical and physical properties and are not functionalized. Electron microscopy, Raman spectroscopy, Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA) and atomic absorption (AA) spectrometry studies were used to characterize the purified SWCNTs.     

High‐Strength Laminated Copper Matrix Nanocomposites Developed from a Single‐Walled Carbon Nanotube Film with Continuous Reticulate Architecture

A critical challenge in nanocomposite fabrication by adding SWCNTs as reinforcement is to realize an effective transfer of the excellent mechanical properties of the SWCNTs to the macroscale mechanical properties of the matrix. Using directly grown SWCNT films with continuous reticulate structure as the template, Cu/SWCNTs/Cu laminated nanocomposites are fabricated by an electrodepositing process. The resulting Cu/SWCNTs/Cu laminated nanocomposites exhibit extremely high strength and Young's modulus. The estimated Young's modulus of the SWCNT bundles in the composite are between 860 and 960 GPa. Such a high strength and an effective load‐transfer capacity are ascribed to the unique continuous reticulate architecture of SWCNT films and the strong interfacial strength between the SWCNTs and Cu matrix. Raman spectroscopy is used to characterize the loading status of the SWCNTs in the strained composite. It provides a route to investigate the load transfer of SWCNTs in the metal matrix composites.     

A High‐Performance Graphene Oxide‐Doped Ion Gel as Gel Polymer Electrolyte for All‐Solid‐State Supercapacitor Applications

A high‐performance graphene oxide (GO)‐doped ion gel (P(VDF‐HFP)‐EMIMBF₄‐GO gel) is prepared by exploiting copolymer (poly(vinylidene fluoride‐hexafluoro propylene), P(VDF‐HFP)) as the polymer matrix, ionic liquid (1‐ethyl‐3‐methylimidazolium tetrafluoroborate, EMIMBF₄) as the supporting electrolyte, and GO as the ionic conducting promoter. This GO‐doped ion gel demonstrates significantly improved ionic conductivity compared with that of pure ion gel without the addition of GO, due to the homogeneously distributed GO as a 3D network throughout the GO‐doped ion gel by acting like a ion “highway” to facilitate the ion transport. With the incorporation of only a small amount of GO (1 wt%) in ion gel, there has been a dramatic improvement in ionic conductivity of about 260% compared with that of pure ion gel. In addition, the all‐solid‐state supercapacitor is fabricated and measured at room temperature using the GO‐doped ion gel as gel polymer electrolyte, which demonstrates more superior electrochemical performance than the all‐solid‐state supercapacitor with pure ion gel and the conventional supercapacitor with neat EMIMBF₄, in the aspect of smaller internal resistance, higher capacitance performance, and better cycle stability. These excellent performances are due to the high ionic conductivity, excellent compatibility with carbon electrodes, and long‐term stability of the GO‐doped ion gel.     

Interdispersed Amorphous MnOx–Carbon Nanocomposites with Superior Electrochemical Performance as Lithium‐Storage Material

The realization of manganese oxide anode materials for lithium‐ion batteries is hindered by inferior cycle stability, rate capability, and high overpotential induced by the agglomeration of manganese metal grains, low conductivity of manganese oxide, and the high stress/strain in the crystalline manganese oxide structure during the repeated lithiation/delithiation process. To overcome these challenges, unique amorphous MnO_x–C nanocomposite particles with interdispersed carbon are synthesized using aerosol spray pyrolysis. The carbon filled in the pores of amorphous MnO_x blocks the penetration of liquid electrolyte to the inside of MnO_x, thus reducing the formation of a solid electrolyte interphase and lowering the irreversible capacity. The high electronic and lithium‐ion conductivity of carbon also enhances the rate capability. Moreover, the interdispersed carbon functions as a barrier structure to prevent manganese grain agglomeration. The amorphous structure of MnO_x brings additional benefits by reducing the stress/strain of the conversion reaction, thus lowering lithiation/delithiation overpotential. As the result, the amorphous MnO_x‐C particles demonstrated the best performance as an anode material for lithium‐ion batteries to date.     

Covalently Bonded Graphene–Carbon Nanotube Hybrid for High‐Performance Thermal Interfaces

The remarkable thermal properties of graphene and carbon nanotubes (CNTs) have been the subject of intensive investigations for the thermal management of integrated circuits. However, the small contact area of CNTs and the large anisotropic heat conduction of graphene have hindered their applications as effective thermal interface materials (TIMs). Here, a covalently bonded graphene–CNT (G‐CNT) hybrid is presented that multiplies the axial heat transfer capability of individual CNTs through their parallel arrangement, while at the same time it provides a large contact area for efficient heat extraction. Through computer simulations, it is demonstrated that the G‐CNT outperforms few‐layer graphene by more than 2 orders of magnitude for the c‐axis heat transfer, while its thermal resistance is 3 orders of magnitude lower than the state‐of‐the‐art TIMs. We show that heat can be removed from the G‐CNT by immersing it in a liquid. The heat transfer characteristics of G‐CNT suggest that it has the potential to revolutionize the design of high‐performance TIMs.     

Systematic Study of Widely Applicable N‐Doping Strategy for High‐Performance Solution‐Processed Field‐Effect Transistors

A specific design for solution‐processed doping of active semiconducting materials would be a powerful strategy in order to improve device performance in flexible and/or printed electronics. Tetrabutylammonium fluoride and tetrabutylammonium hydroxide contain Lewis base anions, F^? and OH^?, respectively, which are considered as organic dopants for efficient and cost‐effective n‐doping processes both in n‐type organic and nanocarbon‐based semiconductors, such as poly[[N,N′‐bis(2‐octyldodecyl)‐naphthalene‐1,4,5,8‐bis(dicarboximide)‐2,6‐diyl]‐alt‐5,5′‐(2,2′‐bithiophene)] (P(NDI2OD‐T2)) and selectively dispersed semiconducting single‐walled carbon nanotubes by π‐conjugated polymers. The dramatic enhancement of electron transport properties in field‐effect transistors is confirmed by the effective electron transfer from the dopants to the semiconductors as well as controllable onset and threshold voltages, convertible charge‐transport polarity, and simultaneously showing excellent device stabilities under ambient air and bias stress conditions. This simple solution‐processed chemical doping approach could facilitate the understanding of both intrinsic and extrinsic charge transport characteristics in organic semiconductors and nanocarbon‐based materials, and is thus widely applicable for developing high‐performance organic and printed electronics and optoelectronics devices.     

Selective Electrochemical Etching of Single‐Walled Carbon Nanotubes

Single‐walled carbon nanotubes (SWNTs) are a promising material for future nanotechnology. However, their applications are still limited in success because of the co‐existence of metallic SWNTs and semiconducting SWNTs produced samples. Here, electrochemical etching, which shows both diameter and electrical selectivity, is demonstrated to remove SWNTs. With the aid of a back‐gate electric field, selective removal of metallic SWNTs is realized, resulting in high‐performance SWNT field‐effect transistors with pure semiconducting SWNT channels. Moreover, electrochemical etching is realized on a selective area. These findings would be valuable for research and the application of SWNTs in electrochemistry and in electronic devices.     

High Electroactive Material Loading on a Carbon Nanotube@3D Graphene Aerogel for High‐Performance Flexible All‐Solid‐State Asymmetric Supercapacitors

Freestanding carbon‐based hybrids, specifically carbon nanotube@3D graphene (CNTs@3DG) hybrid, are of great interest in electrochemical energy storage. However, the large holes (about 400 µm) in the commonly used 3D graphene foams (3DGF) constitute as high as 90% of the electrode volume, resulting in a very low loading of electroactive materials that is electrically connected to the carbon, which makes it difficult for flexible supercapacitors to achieve high gravimetric and volumetric energy density. Here, a hierarchically porous carbon hybrid is fabricated by growing 1D CNTs on 3D graphene aerogel (CNTs@3DGA) using a facile one‐step chemical vapor deposition process. In this architecture, the 3DGA with ample interconnected micrometer‐sized pores (about 5 µm) dramatically enhances mass loading of electroactive materials comparing with 3DGF. An optimized all‐solid‐state asymmetric supercapacitor (AASC) based on MnO₂@CNTs@3DGA and Ppy@CNTs@3DGA electrodes exhibits high volumetric energy density of 3.85 mW h cm^?3 and superior long‐term cycle stability with 84.6% retention after 20 000 cycles, which are among the best reported for AASCs with both electrodes made of pseudocapacitive electroactive materials.     

Capacitive Enhancement Mechanisms and Design Principles of High‐Performance Graphene Oxide‐Based All‐Solid‐State Supercapacitors

Graphene oxide (GO)‐based all‐solid‐state supercapacitors (GO‐A3Ss) are superior over liquid electrolyte‐based supercapacitors and capable of being integrated on a single chip in various geometry shapes for the use of future smart wearable electronics field as a fast energy storage device, but their capacitance need to be improved. Here, a new approach has been developed for enhancing the capacitive capability of the supercapacitors through molecular dynamics simulations with the first‐principle input. A theoretical model of charge storage is developed to understand the unique capacitive enhancement mechanism and to predict the capacitance of the GO‐A3Ss, which agrees well with the experimental observations. A novel supercapacitor with GO and reduced graphene oxide (rGO) alternatively layered structures is designed based on the model, and its energy density is the highest among conventional supercapacitors using liquid electrolytes and all‐solid‐state supercapacitors using aerogels or hydrogels as the solid‐state electrolyte. Based on the predictions, two new types of high‐performance GO/rGO multilayered capacitors are proposed to meet different practical applications. The results of this work provide an approach for the design of high‐performance all‐solid‐state supercapacitors based on GO and rGO materials.     

Chemical Coupling of Carbon Nanotubes and Silicon Nanoparticles for Improved Negative Electrode Performance in Lithium‐Ion Batteries

Multi‐walled carbon nanotube (MWCNT)/silicon nanocomposites obtained by a grafting technique using the diazonium chemistry are used to prepare silicon negative electrodes for lithium‐ion batteries. The covalent bonding of the two compounds is obtained via mono‐ and multi‐layers of phenyl bridges, leading to an ideal dispersion of MWCNTs and silicon nanoparticles that are bound together. The presence of MWCNTs close to silicon nanoparticles enhances the electronic pathway to the active material particles and probably helps to prevent silicon decrepitation upon repeated lithium insertion/extraction by improving the mechanical stability of the electrode at a nanoscale level. This effect results in the enhancement of cycling ability and capacity, which are demonstrated by comparing the nanocomposite electrode to a simple mixture of the two compounds. This technique can be applied to other carbon conductive additives together with silicon or other nanosized active compounds.     

Carbon Fiber–Bismaleimide Composites Filled with Nickel‐Coated Single‐Walled Carbon Nanotubes for Lightning‐Strike Protection

Multifunctional carbon fiber composites are imperative for next‐generation lightweight aircraft structures. However, lightning‐strike protection is a feature that is lacking in many modern carbon fiber high‐temperature polymer systems, due to their high electrical resistivity. This work presents a study on processing, materials optimization, and property development of high‐temperature bismaleimide (BMI)–carbon fiber composites filled with nickel‐coated single‐walled carbon nanotubes (Ni‐SWNTs) based on three key factors: i) dispersion of Ni‐SWNTs, ii) their surface coverage on the carbon plies and, iii) the composite surface resistivity. Atomic force microscopy analysis revealed that coating purified SWNTs with nickel enabled improved dispersion which resulted in uniform surface coverage on the carbon plies. The electrical resistivity of the baseline composite system was reduced by ten orders of magnitude by the addition of 4 wt% Ni‐SWNTs (calculated with respect to the weight of a single carbon ply). Ni‐SWNT–filled composites showed a reduced amount of damage to simulated lightning strike compared to their unfilled counterparts, as indicated by the minimal carbon fiber pull‐out.