Time-resolved studies of photoinduced birefringence in azobenzene dye-doped polymer films

We measured transient photoinduced birefringence (delta n) in various azobenzene dye films by pumping with a nanosecond pulse at 532 nm and probing at 633 nm. The switch-on times for the photoinduced birefringence range from nanoseconds to milliseconds and are systematically related with the lowest optical transition energies for those films. Moreover, our results suggest that the transient photoinduced birefringence measurement is a convenient way to determine the relative energies of pi-pi(*) and n-pi(*) states in azo-based materials.     

All-optical logic gates based on photoinduced anisotropy of bacteriorhodopsin film

All-optical logic gates based on photoinduced anisotropy of bacteriorhodopsin (BR) film are proposed. The photoinduced anisotropy in BR film, which arises from the selective absorption of BR molecules to polarized light, can be controlled by changing the amplitudes and polarizations of exiting beams. As a consequence, the polarization of the probe light passing through the BR film can be controlled by the polarization of the exiting beam. Based on this property, a novel scheme of all-optical logic gates, such as AND, OR, XOR and NOT, has been implemented via the pump-probe technique. A theoretical model for the all-optical logic gates is proposed, and the theoretical predictions are demonstrated with the experimental results.     

Analysis of photoinduced birefringence in azo-dye doped films by a fast imaging technique

In photo-birefringent films, the relationship ρ(I) between optical retardation ρ and pump irradiance I may be obtained with imaging techniques applied within a pump-probe setup. However, measurement of ρ(I) are reported only at long irradiation times and low time-resolution. In this paper we describe a polariscopic imaging technique with higher sensitivity (by a factor of ∼ 30), where the probe beam is focused on the entrance pupil of the camera (“Maxwellian view”). The technique is applied to an azo-dye doped polymeric film, obtaining the continuous ρ(I) curve after irradiation times from 10 ms to 240 ms. Exponential functions are fitted against the experimental data both as a function of time and irradiance.     

Spatial light modulation based on photoinduced change in the complex refractive index of bacteriorhodopsin

Bacteriorhodopsin exhibits photoinduced changes in both absorption and refractive index at 633 nm. To explore the possibility of exploiting this property in constructing a photoaddressed spatial light modulator, we investigated the transmission property of a Fabry-Perot interferometer containing a bacteriorhodopsin thin film. Film was formed that had a phase shift of π/4 and sufficient interference fringe contrast for spatial light modulation. This establishes the possibility of constructing a spatial light modulator that features nonlinear input-output characteristics and can operate at moderate light intensities of the order of tens of milliwatts per centimeter square.     

Dynamics of creation photoinduced birefringence on (PAH/PAZO)n layer-by-layer films: Analysis of consecutive cycles

Reproducibility and reliability of data is an important subject in the development of organic devices for photonics applications. This work reports the analysis of successive photoinduced birefringence creation curves in layer-by-layer films of poly(allylamine hydrochloride) (PAH) and poly{1-(4-(3-carboxy-4-hydroxyphenylazo) benzenesulfonamido)-1,2-ethanediyl, sodium salt} (PAZO) with different number of bilayers. The birefringence creation or writing curves are described by two processes: a faster one referring the contribution of trans–cis–trans photoisomerization cycles to the birefringence; and a slower one associated to the contribution of motion of the polymer chain to the birefringence. As the number of write–erase cycles increases, the characteristic times of these processes decreases, respectively, to values of 18 and 212 s independently of the number of bilayers of films while for the magnitudes the fast process prevailed relatively to the slow, by 70% against 30%. The observed behavior is explained by the thermal treatment given by the laser beam in the irradiated area with increase of free volume which contributes for the chromophore mobility. This conclusion was achieved by measuring the surface temperature during and after irradiation and analyzing by optical microscopy the film surface where an increase of holes and aggregation as a result of irradiation was observed. Infrared spectra of films after and before irradiation showed changes in the CC absorbance indicating aggregation of azobenzene groups while changes in the protonated and deprotonated carboxylic acid groups are consistent with ionization degree diminishing which is explained by the removal of water molecules by heating caused by laser. The results presented in this paper indicates that an increase in the number of write–erase cycles contributes to reliable and reproducible birefringence characteristics of PAH/PAZO films – a good new from point of view of possible applications.     

Kinetics of photoinduced anisotropy in bacteriorhodopsin film under two pumping beams

Photoinduced anisotropy in bacteriorhodopsin (BR) film arises from the selective bleaching of BR molecules to linearly polarized light. The kinetics of photoinduced anisotropy excited by single and two pumping beams are investigated theoretically and experimentally. Compared with a single pumping beam (650 nm), which produces comparatively small photoinduced anisotropy, dual-wavelength linearly polarized pumping beams (650 and 405 nm) can obviously change the photoinduced anisotropy. When the polarization orientation of the 405 nm pumping beam is perpendicular to that of the 650 nm pumping beam, the peak and steady values of the photoinduced anisotropy kinetic curves are remarkably enhanced. But when the two pumping beams have parallel polarization orientation, the peak and steady values are restrained. At a fixed intensity of the 650 nm pumping beam, there exists an optimal intensity for the 405 nm pumping beam to maximize the value of the photoinduced anisotropy. The photoinduced transmittance of the polarizer-BR-analyzer system is modulated by the polarization angle of the 405 nm pumping beam in an approximate-cosine form.     

High-contrast, all-optical switching in bacteriorhodopsin films

We report experiments with nonlinear-absorption-based, high-contrast, all-optical switching in photochromic bacteriorhodopsin (BR) films. The switching action is accomplished by control of the transmission of a weak probe beam through a BR sample with the help of strong pump beam illumination at 532 nm wavelength. We found that the switching properties of BR films depend on several experimentally controllable parameters such as probe wavelength, pump beam intensity, and excitation rate. A comparative study of the switching behavior and other parameters of practical use was carried out at three probe wavelengths (543, 594, and 633 nm) and various beam powers and pump excitation rates. The results are presented for commercially available wild-type and D96N variant BR films.     

Photo-induced anisotropic photoelectric response in oriented bacteriorhodopsin films

The photo-induced anisotropic properties of the chromophore protein bacteriorhodopsin (bR) are of interest for possible applications in optical image processing and spatial filtering. Here we report experimental results on the photo-induced anisotropic photoelectric response of dried oriented bR films. A polarization dependent photovoltage is measured across an ITO/bR/ITO photodetector. The anisotropy is introduced by a 632.8 nm linearly polarized pump beam and is detected with a 594.1 nm polarized probe beam. The influence of the pump light intensity on the photovoltage anisotropy has also been investigated. A model, based on the polarization dependent photoselection of the bR molecules reasonably explains the behavior of the measured data. The observed effect can be used to construct a polarization sensitive bR-based bio-photoreceiver.     

Modeling the grating-formation process in thick bacteriorhodopsin films

We model the grating-formation process in bacteriorhodopsin films for the interference of two plane waves. We simulate the temporal dependence of grating recording and readout, and we examine the behavior of the diffraction efficiency with respect to exposure, write and read wavelengths, and film parameters such as initial optical density and lifetime of the upper state. Gratings written in thick bacteriorhodopsin films are generally nonuniform and nonsinusoidal owing to the absorption and saturation properties of the material. The simulations also show that one can often obtain optimization of hologram recording and readout by writing and reading at wavelengths far off the peak of the ground-state absorbance spectrum, especially for films with high values of the peak optical density.     

Enhanced birefringence in vacuum evaporated silicon thin films

We report an experimental study of enhanced optical birefringence in silicon thin films on glass substrates. Form anisotropy is introduced as an atomic-scale morphological structure through dynamic control of growth geometry. The resulting birefringence is large compared with naturally anisotropic crystals and is comparable to two-dimensional photonic crystals. The films are fabricated with serial bideposition onto a substrate held at a fixed tilt angle relative to the impinging vapor. Films were analyzed by spectroscopic ellipsometry and scanning electron microscopy, the latter clearly revealing form anisotropy in a morphology of bunched columns perpendicular to the deposition plane with dimensions of hundreds of nanometers and smaller. The observed linear birefringence varies with wavelength and tilt angle, with a maximum of 0.4 at a 630-nm wavelength and 0.25 at 1500 nm.     

Linear birefringence control and magnetization in sputter-deposited magnetic garnet films

Birefringence control is essential in the fabrication of on-chip magnetooptic Faraday isolators. We report on film thickness and stress studies of birefringence in sputter-deposited single-layer bismuth-substituted iron garnet films and double-layer iron garnet films with gadolinium gallium garnet (GGG) covers. We examine compressively and tensilely strained films and analyze the photoelastic response of the sputter-deposited garnet films. We show that the net birefringence can be ed out under planar compressive strain conditions. Bilayer GGG on iron garnet film yields a reduced birefringence. Temperature control during the sputter deposition of the GGG cover is critical and strongly influences the magnetic moment and birefringence level in the waveguide. High-temperature deposition lowers the magnetization in the underlying iron garnet film.     

Application of bacteriorhodopsin films in an adaptive-focusing schlieren system

The photochromic property of bacteriorhodopsin films is exploited in the application of a focusing schlieren optical system for the visualization of optical phase information. By encoding an image on the film with light of one wavelength and reading out with a different wavelength, the readout beam can effectively see the photographic negative of the original image. The potential advantage of this system over previous focusing schlieren systems is that the updatable nature of the bacteriorhodopsin film allows system adaptation. I discuss two image encoding and readout techniques for the bacteriorhodopsin and use film transmission characteristics to choose the more appropriate method. I demonstrate the system principle with experimental results using argon-ion and He-Cd lasers as the two light sources of different wavelengths, and I discuss current limitations to implementation with a white-light source.     

Biosensor arrays based on the degradation of thin polymer films interrogated by scanning photoinduced impedance microscopy

Disposable sensors based on the degradation of thin films as a result of an enzymatic reaction have been developed into efficient enzyme detectors. Film degradation has traditionally been monitored using surface plasmon resonance (SPR), quartz crystal microbalance (QCM), or classical ac impedance measurements. The enzyme detection principle has now been integrated with an array technology derived from a recently developed impedance imaging technique, scanning photoinduced impedance microscopy (SPIM). SPIM is based on photocurrent measurements at field-effect structures. The material under investigation is commonly deposited onto a semiconductor-insulator substrate. In this work, field-effect capacitors were replaced by hydrogenated amorphous silicon (a-Si:H) n-i-p photodiode structures, which have recently been shown to be suitable for SPIM measurements with good lateral resolution. To demonstrate the feasibility of SPIM for the characterization of biosensor arrays, polymer dots of the inert polymer cellulose acetate and an alpha-chymotrypsin-sensitive poly(ester amide) were deposited onto a-Si:H n-i-p/SiO2 structures and their enzymatic degradation was monitored using a laser scanning setup.     

Optical properties and photoinduced changes in amorphous AsS films

The dependence on composition of optical properties and photoinduced changes in thin films of As_xS_100?x with x between 15 and 45 were investigated. The optical band gap and the single oscillator fitting constants show extreme at the stoichiometric composition x = 40 and they vary almost linearly with sulphur content in specimens containing an excess of chalcogen. In contrast, irreversible and reversible photoinduced changes of the optical properties accompany a characteristic transition at x ≈ 30. This suggests that the origin of these effects is attributable to transformations of AsS and SS bonds in films containing an excess of chalcogen. This speculation is supported by thermal analyses.     

Low-frequency and high-frequency all-fiber modulators based on birefringence modulation

In-line optical modulators with low insertion losses and high maximum optical powers are required for Q switching and cavity dumping of fiber lasers as well as for nonlinear optical-fiber experiments. We report the design of polarimetric all-fiber modulators based on optical-fiber birefringence modulation combined with an all-fiber polarizer. Birefringence modulation involves a piezoelectric ceramic tube. This simple technique permits efficient low-frequency and high-frequency harmonic modulation, up to the megahertz range, as well as modulation of pulses shorter than 1 mus.     

Femtosecond laser-induced permanent anisotropy in bacteriorhodopsin films and applications in optical data storage

In polymeric films of bacteriorhodopsin (BR) a photoconversion product named F₅₄₀-state, which is excited by 790 nm femtosecond laser pulses, is stable either for photochemical reaction or thermal pathway. The optical properties of the F₅₄₀-state were studied, and Jones-matrix theory was adopted to analyze the photoinduced anisotropy of the F₅₄₀-state. Based on the permanently photoinduced anisotropy, write-once-read-many (WORM) optical data storage was demonstrated by using two polarization states of femtosecond pulsed laser. Since the polarization information is also written on the storage media, it is impossible to copy it in a common way. This storage technique has a potential application in advanced optical security.     

Spectral relationship of photoinduced refractive index and absorption changes in fulgide films

Fulgides are one kind of organic photochromic compound, which are famous for their thermal irreversibility. In this report, from the difference spectra of the absorption ΔA(λ) of one kind of pyrrylfulgide, the spectral refractive index change Δn(λ) was calculated by the Kramers–Kronig relation (KKR), and a good correlation of theoretically derived values and the experimental values of the Δn measured by a modified Michelson interferometer was found. Further, it is demonstrated that it was possible to calculate the spectral dependence of diffraction efficiency from the easily accessible absorption changes. This method will be a useful tool for the characterization and optimization of fulgide films. The results show that the diffraction efficiency is high at 488 and 750 nm, where the absorption is very small, so we can realize non-destructive reconstruction.