集成宽频Σ-Δ分数频率合成器的实现

提出了一种新型低噪声、宽跟踪范围的集成分数频率合成器.该合成器采用3位3阶Σ-Δ调制器和对数字信号进行粗调、对模拟信号进行微调的宽频开关电容阵列LC压控振荡器,其中,数字和模拟调谐控制信号由4位2级并行流水线A/D转换器产生.详细分析了该合成器的结构和实现电路,并采用0.25 μm CMOS工艺实现.测试结果显示,电路在偏离载波频率10 kHz处带内相位噪声为-86.2 dBc/Hz,在偏离载波频率2 MHz处的带外相位噪声为-130 dBc/Hz,且具有小于5 Hz的频谱分辨率.     

一种采用开关阶跃电容的压控振荡器(下): 电路设计和实现

为了验证阶跃可变电容压控振荡器调谐特性理论分析的正确性,提出了一种采用开关阶跃电容的新型压控振荡器电路,该压控振荡器电路采用0.25μm 1P5M CMOS工艺实现.一种新型开关阶跃电容实现了频率调谐功能,该电容的调谐电容是传统反型MOS管可变电容的146%.在1/f3区域,差分调谐振荡器的相位噪声比单端调谐振荡器低7dB.在载波频率偏差10kHz,100kHz和1MHz处测得差分调谐时的相位噪声分别是-83,-107和-130dBc/Hz,功耗为8.6mW.     

一种采用开关阶跃电容的压控振荡器(下): 电路设计和实现

为了验证阶跃可变电容压控振荡器调谐特性理论分析的正确性,提出了一种采用开关阶跃电容的新型压控振荡器电路,该压控振荡器电路采用0.25μm 1P5M CMOS工艺实现.一种新型开关阶跃电容实现了频率调谐功能,该电容的调谐电容是传统反型MOS管可变电容的146%.在1/f3区域,差分调谐振荡器的相位噪声比单端调谐振荡器低7dB.在载波频率偏差10kHz,100kHz和1MHz处测得差分调谐时的相位噪声分别是-83,-107和-130dBc/Hz,功耗为8.6mW.     

低功耗低噪声正交压控振荡器设计

设计了一种用于WLAN 802.11 n收发机频率合成器的新颖低功耗、低相位噪声正交输出LC电压控制振荡器(QVCO)。电路设计中使用了Cadence IC5.033和ADS2004软件以及TSMC0.18μm CMOS工艺模型库,电路依靠并联的耦合支路相互作用使两个独立压控振荡器输出相位成正交,采用PMOS并联耦合支路和开关控制偏置两种新技术降低了VCO的相位噪声,其仿真结果为1 MHz频偏处-128.6 dBc/Hz和10 kHz频偏处-84 dBc/Hz。采用数字电容阵列提高了QVCO的频率调谐范围,QVCO的频率范围仿真结果为3.1 GHz~4.1 GHz。QVCO的电源电压为1.8 V,功耗17 mW。实现了低功耗正交输出压控振荡器,同时通过新颖的电路设计技术改善了相位噪声,改变了正交输出LC压控振荡器高噪声的传统观念,为今后在正交输出LC压控振荡器的设计提供了一些参考。     

具有电容阵列和电感阵列的1.8~2.6GHz CMOS压控振荡器

设计了一个具有开关电容阵列和开关电感阵列的1.76~2.56GHz CMOS压控振荡器。电路采用0.18µm 1P6M CMOS工艺实现。经测试,压控振荡器的频率调谐范围为37%。在频率调谐范围内及1MHz频偏处,相位噪声变化范围为-118.5dBc/Hz至 -122.8dBc/Hz。在1.8V电源电压下,功耗约为14.4mW。基于具有电容阵列和电感阵列的可重构LC谐振回路,对压控振荡器的调谐范围参数进行了分析和推导,所得结果为电路设计提供了指导。     

1V 2.5GHz压控振荡器设计

设计了1V,2.5GHz的全集成压控振荡器.通过优化集成电感的设计,同时采用NMOS管和开关电容阵列作为可变电容,使该设计具有较低的相位噪声和较宽的调谐范围.采用0.18μm CMOS工艺进行仿真,结果显示,在1V电源电压下,在偏离中心频率600kHz处的相位噪声为-119dBc/Hz,调谐范围为28%,功耗为3.6mW.     

应用于IMT-A和UWB系统的0.13μm CMOS宽带压控振荡器设计

基于TSMC 0.13μm CMOS工艺设计并实现了应用于IMT-Advanced和UWB系统的双频段宽带频率合成器中的电感电容压控振荡器(LC-VCO)。此压控振荡器的设计采用了开关电流源、开关交叉耦合对和噪声滤波等技术,以优化电路的相位噪声,功耗,振荡幅度,调谐范围等性能。为达到宽的调谐范围,核心电路采用了4比特可重构的开关电容调谐阵列。整个芯片包括焊盘面积为1.11′0.98 mm₂。测试结果表明,在1.2V电源电压下,两个频段压控振荡器所消耗的电流分别为3mA和4.5mA,压控振荡器的调谐范围为3.86~5.28GHz和3.14~3.88GHz。在振荡频率3.5GHz和4.2GHz上,1MHz频偏处,压控振荡器的相位噪声分别为-123dBc/Hz与-119dBc/Hz。     

一个自调谐,自适应的1.9GHz分数/整数频率综合器

本文提出了一个具有自调谐,自适应功能的1.9GHz的分数/整数锁相环频率综合器.该频率综合器采用模拟调谐和数字调谐相结合的技术来提高相位噪声性能.自适应环路被用来实现带宽自动调整,可以缩短环路的建立时间.通过打开或者关断 ΣΔ 调制器的输出来实现分数和整数分频两种工作模式,仅用一个可编程计数器实现吞脉冲分频器的功能.采用偏置滤波技术以及差分电感,在片压控振荡器具有很低的相位噪声;通过采用开关电容阵列,该压控振荡器可以工作在1.7GHz~2.1GHz的调谐范围.该频率综合器采用0.18 μ m,1.8V SMIC CMOS工艺实现.SpectreVerilog仿真表明:该频率综合器的环路带宽约为100kHz,在600kHz处的相位噪声优于-123dBc/Hz,具有小于15 μ s的锁定时间.     

一种宽带低相噪CMOS LC压控振荡器设计

设计了一种频率可调范围约830MHz全集成CMOS LC压控振荡器.该压控振荡器利用了一种改进的四位二进制加权的开关电容阵列扩大了其调谐范围;采用了可变尾电流源设计,使得振荡信号在整个频率范围内幅度变化不大.结果表明,该压控振荡器总调节范围1.12～1.95GHz,功耗为6.5～19.1mW,采用0.35μm CMOS RF工艺设计版图面积为360μm×830μm,工作于1.1GHz和1.9GHz时,1MHz频偏处的单边带相位噪声分别为-122dBc/ Hz、-120dBc/ Hz.     

一种面向IEEE 802.11ac标准的5 GHz LC压控振荡器

基于TSMC RF 0.18 μm CMOS工艺,设计了一种可应用于IEEE 802.11ac标准的5 GHz宽带LC压控振荡器。该振荡器采用了NMOS交叉耦合结构,同时采用了5位开关电容阵列以扩展调谐范围。开关电容阵列使压控振荡器的增益KVCO保持在一个较小的值,有效地降低了压控振荡器的相位噪声。后仿真结果表明,该压控振荡器在1.8 V电源电压下,功耗为9 mW,频率调谐范围为4.52~5.56 GHz,在偏离中心频率1 MHz处仿真得到的相位噪声为-124 dBc/Hz。该LC 压控振荡器的版图尺寸为320 μm×466 μm。     

A 900-MHz 2.5-mA CMOS frequency synthesizer with an automatic SCtuning loop

A 900-MHz phase-locked loop frequency synthesizer implemented in a 0.6-μm CMOS technology is developed for the wireless integrated network sensors applications. It incorporates an automatic switched-capacitor (SC) discrete-tuning loop to extend the overall frequency tuning range to 20%, while the VCO gain (K_VCO) resulting from the CMOS varactor continuous-tuning is kept low at only 20 MHz/V in order to improve the reference spurs and noise performance. This frequency synthesizer achieves a phase noise of -102 dBc/Hz at 100 kHz offset frequency and reference spurs below -55 dBc. The synthesizer, including an on-chip VCO, dissipates only 2.5 mA from a 3-V supply     

用于434/868MHz FSK/OOK CMOS发射机的锁相环设计

一种可输出434/868MHz信号的Σ-Δ分数分频锁相环在0.35μmCMOS工艺中集成。该发射机系统采用直接调制锁相环分频比的方式实现FSK调制,OOK的调制则通过功率预放大器的开-关实现。为了降低芯片的成本和功耗,发射机采用了电流数字可控的压控振荡器(VCO),以及片上双端-单端转换电路,并对分频器的功耗设计进行研究。经测试表明,锁相环在868MHz载波频偏为10kHz、100kHz和3MHz处的相位噪声分别为-75dBc/Hz、-104dBc/Hz和-131dBc/Hz,其中的VCO在100kHz频偏处的相位噪声为-108dBc/Hz。在发送模式时,100kHz相邻信道上的功率与载波功率之比小于-50dB。在直流电压2.5V的工作条件下,锁相环的电流为12.5mA,包括功率预放大器和锁相环在内的发送机总面积为2mm2。     

一种用于双波段GPS接收机的低功耗宽带CMOS频率合成器

提出了一种用于双波段GPS接收机的宽带CMOS频率合成器.该GPS接收机芯片已经在标准O.18μm射频CMOS工艺线上流片成功,并通过整体功能测试.其中压控振荡器可调振荡频率的覆盖范围设计为2～3.6GHz,覆盖了L1,L2波段的两倍频的频率点.并留有足够的裕量以确保在工艺角和温度变化较大时能覆盖所需频率.芯片测试结果显示,该频率综合器在L1波段正常工作时的功耗仅为5.6mW,此时的带内相位噪声小于-82dBc/Hz,带外相位噪声在距离3.142G载波1M频偏处约为-112dBc/Hz,这些指标很好地满足了GPS接收芯片的性能要求.     

A 2 V 1.8 GHz fully integrated CMOS dual-loop frequency synthesizer

A 2 V 1.8 GHz fully integrated CMOS dual-loop frequency synthesizer is designed in a standard 0.5 /spl mu/m digital CMOS process for wireless communication. The voltage-controlled oscillator (VCO) required for the low-frequency loop is designed using a ring-type VCO and achieves a tuning range of 89% from 356 to 931 MHz and a phase noise of -109.2 dBc/Hz at 600 kHz offset from 856 MHz. With an active chip area of 2000/spl times/1000 /spl mu/m/sup 2/ and at a 2 V supply voltage, the whole synthesizer achieves a tuning range from 1.8492 to 1.8698 GHz in 200 kHz steps with a measured phase noise of -112 dBc/Hz at 600 kHz offset from 1.86 GHz. The measured settling time is 128 /spl mu/s and the total power consumption is 95 mW.     

An integrated 8-12 GHz fractional-N frequency synthesizer in SiGe BiCMOS for satellite communications

We present an integrated fractional-N low-noise frequency synthesizer for satellite applications. By using two integrated VCOs and combining digital and analog tuning techniques, a PLL lock range from 8 to 12 GHz is achieved. Due to a small VCO fine tuning gain and optimized charge pump output biasing, the phase noise is low and almost constant over the tuning range. All 16 sub-bands show a tuning range above 900 MHz each, allowing temperature compensation without sub-band switching. This makes the synthesizer robust against variations of the device parameters with process, supply voltage, temperature and aging. The measured phase noise is ?87 dBc/Hz and ?106 dBc/Hz at 10 kHz and 1 MHz offset, respectively. In integer-N mode, phase noise values down to ?98 dBc/Hz at 10 kHz and ?111 dBc/Hz at 1 MHz offset, respectively, were measured.     

A technique to improve the linearization of frequency–voltage characteristic of LC-VCO

This paper presents a very low-power linearization technique to improve the linearity of frequency-voltage characteristic of LC-VCO (voltage controlled oscillator) using MOS varactor. This reduces the VCO gain (K _VCO) variation and its required value over the tuning voltage range. Low K _VCO improves noise and reference spur performances at the output of phase lock loop/frequency synthesizer (FS). Low K _VCO variation reduces FS loop stability problem. Using this VCO circuit, a fully on-chip integer-N frequency synthesizer has been fabricated in 0.18 μm epi-digital CMOS technology for 2.45 GHz ZigBee application. The measured VCO phase noise is ?115.76 and ?125.23 dBc/Hz at 1 and 3 MHz offset frequencies, respectively from 2.445 GHz carrier and the reference spur of the frequency synthesizer is ?68.62 dBc. The used supply voltage is 1.5 V.     

A fully integrated low-noise 1-GHz frequency synthesizer design formobile communication application

This paper describes a fully monolithic phase-locked loop (PLL) frequency synthesizer circuit implemented in a standard 0.8-μm CMOS technology. To be immune to noise, all the circuits in the synthesizer use differential schemes with the digital parts designed by static logic. The experimental voltage controlled oscillator (VCO) has a center frequency of 800 MHz and a tuning range of ±25%. The measured frequency synthesizer performance has a frequency range from 700 MHz to 1 GHz with -80 dBc/Hz phase noise at a 100 kHz carrier offset. With an active area of 0.34 mm², the test chip consumes 125 mW at maximum frequency from a 5 V supply. The only external components are the supply decoupling capacitors and a passive filter     

A 0.13μm CMOS △∑ fractional-N frequency synthesizer for WLAN transceivers

A fractional-N frequency synthesizer fabricated in a 0.13 μm CMOS technology is presented for the application of IEEE 802.11 b/g wireless local area network (WLAN) transceivers.A monolithic LC voltage controlled oscillator (VCO) is implemented with an on-chip symmetric inductor.The fractional-N frequency divider consists of a pulse swallow frequency divider and a 3rd-order multistage noise shaping (MASH) △ ∑ modulator with noise-shaped dithering techniques.Measurement results show that in all channels,phase noise of the synthesizer achieves -93 dBc/Hz and -118 dBc/Hz in band and out of band respectively with a phase-frequency detector (PFD) frequency of 20 MHz and a loop bandwidth of 100 kHz.The integrated RMS phase error is no more than 0.8°.The proposed synthesizer consumes 8.4 mW from a 1.2 V supply and occupies an area of 0.86 mm2.     

A /spl Sigma/-/spl Delta/ fractional-N frequency synthesizer using a wide-band integrated VCO and a fast AFC technique for GSM/GPRS/WCDMA applications

A fractional-N frequency synthesizer (FNFS) in a 0.5-/spl mu/m SiGe BiCMOS technology is implemented. In order to operate in a wide-band frequency range, a switched-capacitors bank LC tank voltage-controlled oscillator (VCO) and an adaptive frequency calibration (AFC) technique are used. The measured VCO tuning range is as wide as 600 MHz (40%) from 1.15 to 1.75 GHz with a tuning sensitivity from 5.2 to 17.5 MHz/V. A 3-bit fourth-order /spl Sigma/-/spl Delta/ modulator is used to reduce out-of-band phase noise and to meet a frequency resolution of less than 3 Hz as well as agile switching time. The experimental results show -80 dBc/Hz in-band phase noise within the loop bandwidth of 25 kHz and -129 dBc/Hz out-of-band phase noise at 400-kHz offset frequency. The fractional spurious is less than -70 dBc/Hz at 300-kHz offset frequency and the reference spur is -75 dBc/Hz. The lock time is less than 150 /spl mu/s. The proposed synthesizer consumes 19.5 mA from a single 2.8-V supply voltage and meets the requirements of GSM/GPRS/WCDMA applications.