Performance of Pt-Fe/mordenite monolithic catalysts for preferential oxidation of carbon monoxide in a reformate gas for PEFCs

Pt-Fe/mordenite catalysts coated on ceramic straight-channel monoliths were evaluated for the preferential oxidation of carbon monoxide (PROX) in hydrogen-rich gas streams. In a feed gas containing 1% CO, 1% O₂, with the balance H₂, CO conversion reached almost 100% at temperatures ranging from 100 to 130 °C, i.e., an outlet CO concentration of less than 10 ppm. Even in a synthetic reformate gas (1% CO, 1% O₂, 15% H₂O, 20% CO₂, balance H₂), the monolithic catalyst exhibited excellent activity, reducing the CO concentration to less than 100 ppm. In particular, under optimized conditions, an outlet CO concentration of less than 10 ppm was realized. This is the first report that has demonstrated that monolithic catalysts could achieve the 10-ppm target level at a low O₂/CO ratio and a high space velocity in a single-stage reactor. Excellent durability of the monolithic catalyst is expected, based on a lack of deterioration in performance during 500 h of operation.     

Preferential oxidation of carbon monoxide over Pt, Au monometallic catalyst, and Pt–Au bimetallic catalyst supported on ceria in hydrogen-rich reformate

The objective of this paper was to study a preferential oxidation (PROX) of carbon monoxide over monometallic catalysts including Pt, Au and Pt–Au bimetallic catalyst supported on ceria in hydrogen-rich reformate. Single step sol–gel method (SSG) and impregnation on sol–gel method (ISG) were chosen for the preparation of the catalysts. The characteristics of these catalysts were investigated by X-ray diffractometer (XRD), Brunauer–Emmet–Teller (BET) method, transmission electron microscope (TEM), scanning electron microscope (SEM) and temperature-programmed reduction (TPR). The XRD patterns of the catalysts showed only the peaks of ceria crystallite and no metal peak appeared. From TEM images, the active components were seen to be dispersed throughout the ceria support. The TPR patterns of PtAu/CeO₂ catalyst prepared by SSG showed the reduction peaks were within a low temperature range and therefore, the catalysts prepared by SSG exhibited excellent catalytic activity for preferential oxidation of CO. Bimetallic Pt–Au catalyst improved the activity (90% conversion and 50% selectivity at 90 °C) because of the formation of a new phase. When the metal content of (1:1) PtAu/CeO₂ catalyst prepared by SSG was increased, the CO conversion did not change much while the selectivity decreased in the low temperature range (50–90 °C). The CO conversion increased with increasing W/F ratio. The presence of CO₂ and H₂O had a negative effect on CO conversion and selectivity due to blocking of carbonate and water on active sites.     

Development of novel Ru catalyst of preferential CO oxidation for residential polymer electrolyte fuel cell systems

CO preferential oxidation on a novel Ru catalyst greatly improved in activity and selectivity over a wide temperature range by the pre-treatment of H₂ reduction was characterized. The high performance was obtained by increasing the population of surface Ru(0) which improved O₂ activation at low temperatures. Methanation of CO on the catalyst can also contribute to the final CO clean-up from ca. 100 to <1 ppm at low temperatures where the influence of CO₂ methanation can be ignored.     

Kinetics of CO and H2 oxidation over CuO-CeO2 catalyst in H2 mixtures with CO2 and H2O

The kinetics of CO and H₂ oxidation over a CuO-CeO₂ catalyst were simultaneously investigated under reaction conditions of preferential CO oxidation (PROX) in hydrogen-rich mixtures with CO₂ and H₂O. An integral packed-bed tubular reactor was used to produce kinetic data for power-law kinetics for both CO and H₂ oxidations. The experimental results showed that the CO oxidation rate was essentially independent of H₂ and O₂ concentrations, while the H₂ oxidation rate was practically independent of CO and O₂ concentrations. In the CO oxidation, the reaction orders were 0.91, −0.37 and −0.62 with respect to the partial pressure of CO, CO₂ and H₂O, respectively. In the H₂ oxidation, the orders were 1.0, −0.48 and −0.69 with respect to the partial pressure of H₂, CO₂ and H₂O, respectively. The activation energies of the CO oxidation and the H₂ oxidation were 94.4 and 142 kJ/mol, respectively. The rate expressions of both oxidations were able to predict the performance of the PROX reactor with accuracy. The independence between the CO and the H₂ oxidation suggested different sites for CO and H₂ adsorption on the CuO-CeO₂ catalyst. Based on the results, we proposed a new reaction model for the preferential CO oxidation. The model assumes that CO adsorbs selectively on the Cu⁺ sites; H₂ dissociates and adsorbs on the Cu⁰ sites; the adsorbed species migrates to the interface between the copper components and the ceria support, and reacts there with the oxygen supplied by the ceria support; and the oxygen deficiency on the support is replenished by the oxygen in the reaction mixture.     

Development of residential PEFC cogeneration systems: Ru catalyst for CO preferential oxidation in reformed gas

The performance of the novel Ru catalyst in a single-stage CO preferential oxidation removal reactor was investigated for residential polymer electrolyte fuel cell (PEFC) cogeneration systems. The outlet CO concentration of the CO removal reactor was reduced to less than 1 ppm even at [O₂]/[CO]=1.5. The natural gas fuel processor equipped with the CO removal reactor achieved the target thermal efficiency of 77% (LHV). Moreover, the durability of the Ru catalyst has been confirmed for more than 16,000 h at a micro-reactor and for more than 8000 h at an actual CO removal reactor. Because of the low O₂/CO molar ratio, the high CO removal conversion and the long-term durability, the Ru catalyst contributes to the development of residential PEFC cogeneration systems.     

Preferential oxidation of CO over CuO/CeO2 and Pt-Co/Al2O3 catalysts in micro-channel reactors

Micro-channel plates with dimension of 1 mm × 0.3 mm × 48 mm were prepared by chemical etching of stainless steel plates followed by wash coating of CeO₂ and Al₂O₃ on the channels. After coating the support on the plate, Pt, Co, and Cu were added to the plate by incipient wetness method. Reaction experiments of a single reactor showed that the micro-channel reactor coated with CuO/CeO₂ catalyst was highly selective for CO oxidation while the one coated with Pt-Co/Al₂O₃ catalyst was highly active for CO oxidation. The 7-layered reactors coated with two different catalysts were prepared by laser welding and the performances of each reactor were tested in large scale of PROX conditions. The multi-layered reactor coated with Pt-Co/Al₂O₃ catalyst was highly active for PROX and the outlet concentration of CO gradually increased with the O₂/CO ratio due to the oxidation of H₂ which maintained the reactor temperature. The multi-layered reactor coated with CuO/CeO₂ showed lower catalytic activity than that coated with Pt catalyst, but its selectivity was not changed with the increase of O₂/CO ratios due to the high selectivity. In order to combine advantages (high activity and high selectivity) of the two individual catalysts (Pt-Co/Al₂O₃, CuO/CeO₂), a serial reactor was prepared by connecting the two multi-layered micro-channel reactors with different catalysts. The prepared serial reactor exhibited excellent performance for PROX.     

Modification of catalytic performances due to the co-feeding of hydrogen or carbon dioxide in the partial oxidation of methane over a NiO/γ-Al2O3 catalyst

The influence of the addition of 1–10 vol.% of hydrogen or carbon dioxide to the feed during the partial oxidation of methane was studied over a NiO/γ-Al₂O₃ catalyst. The addition of H₂ decreases the conversion and syngas selectivity. This decrease of performance seems to be related to a higher reduction of the catalyst due to the H₂ co-feeding. The addition of CO₂ also appears unfavorable to the production of hydrogen but increases the CO yield. A combination of the dry reforming and the reverse water gas shift reactions is suggested to explain the observed modifications in the product yields.     

Reaction and oxygen permeation studies in Sm0.4Ba0.6Fe0.8Co0.2O3 − δ membrane reactor for partial oxidation of methane to syngas

A disk-type Sm_0.4Ba_0.6Co_0.2Fe_0.8O_3 − δ perovskite-type mixed-conducting membrane was applied to a membrane reactor for the partial oxidation of methane to syngas (CO + H₂). The reaction was carried out using Rh (1 wt%)/MgO catalyst by feeding CH₄ diluted with Ar. While CH₄ conversion increased and CO selectivity slightly decreased with increasing temperature, a high level of CH₄ conversion (90%) and a high selectivity to CO (98%) were observed at 1173 K. The oxygen flux was increased under the conditions for the catalytic partial oxidation of CH₄ compared with that measured when Ar was fed to the permeation side. We investigated the reaction pathways in the membrane reactor using different membrane reactor configurations and different kinds of gas. In the membrane reactor without the catalyst, the oxygen flux was not improved even when CH₄ was fed to the permeation side, whereas the oxygen flux was enhanced when CO or H₂ was fed. It is implied that the oxidation of CO and H₂ with the surface oxygen on the permeation side improves the oxygen flux through the membrane, and that CO₂ and H₂O react with CH₄ by reforming reactions to form syngas.     

Production of middle distillate in a dual-bed reactor from synthesis gas through wax cracking: Effect of acid property of Pd-loaded solid acid catalysts on the wax conversion and middle distillate selectivity

Although alumina-supported gold nanoparticles are poor catalysts for the oxidation of carbon monoxide, they have turned out to be promising candidates for the preferential oxidation of CO in hydrogen-rich streams (PrOx), as hydrogen apparently enhances the CO oxidation rate. The mechanism of this promotion effect is unclear. In this study, we carry out kinetic measurements on the PrOx reaction catalyzed by a 0.9% Au/Al₂O₃ catalyst, which is prepared by direct anionic exchange. We show that the apparent activation energy of the oxidation of CO is lower than that of the oxidation of H₂, whatever the hydrogen content in the feed. On the other hand, the hydrogen partial reaction order is higher in the oxidation of H₂ than in the oxidation of CO. Thus, the CO oxidation rate is significantly increased at low temperature by the introduction of only a small amount of hydrogen in the reactant mixture. At higher temperatures, the selectivity to CO₂ decreases due to competition with the oxidation of H₂. Higher hydrogen concentrations cause the competition between CO and H₂ oxidations to start at lower temperatures. It is proposed that hydrogen reacts with oxygen to yield highly oxidizing intermediates that selectively react with CO as long as the energetic barrier to produce water from these intermediates is not crossed.     

MnOx/Pt/Al2O3 catalysts for CO oxidation in H2-rich streams

The catalytic activity of Pt on alumina catalysts, with and without MnO_x incorporated to the catalyst formulation, for CO oxidation in H₂-free as well as in H₂-rich stream (PROX) has been studied in the temperature range of 25–250 °C. The effect of catalyst preparation (by successive impregnation or by co-impregnation of Mn and Pt) and Mn content in the catalyst performance has been studied. A low Mn content (2 wt.%) has been found not to improve the catalyst activity compared to the base catalyst. However, catalysts prepared by successive impregnation with 8 and 15 wt.% Mn have shown a lower operation temperature for maximum CO conversion than the base catalyst with an enhanced catalyst activity at low temperatures with respect to Pt/Al₂O₃. A maximum CO conversion of 89.8%, with selectivity of 44.9% and CO yield of 40.3% could be reached over a catalyst with 15 wt.% Mn operating at 139 °C and λ = 2. The effect of the presence of 5 vol.% CO₂ and 5 vol.% H₂O in the feedstream on catalysts performance has also been studied and discussed. The presence of CO₂ in the feedstream enhances the catalytic performance of all the studied catalysts at high temperature, whereas the presence of steam inhibits catalysts with higher MnO_x content.     

Oxidation of H2S on activated carbon KAU and influence of the surface state

Properties of the oxidized activated carbon KAU treated at different temperatures in inert atmosphere were studied by means of DTA, Boehm titration, XPS and AFM methods and their catalytic activity in H₂S oxidation by air was determined. XPS analysis has shown the existence of three types of oxygen species on carbon catalysts surface. The content of oxygen containing groups determined by Boehm titration is correlated with their amount obtained by XPS. Catalytic activity of the KAU catalysts in selective oxidation of hydrogen sulfide is connected with chemisorbed charged oxygen species (O_3.1 oxygen type with BE 536.8–537.7 eV) present on the carbons surface.

Formation of dense sulfur layer (islands of sulfur) on the carbons surface and removal of active oxygen species are the reason of the catalysts deactivation in H₂S selective oxidation. The treatment of deactivated catalyst in inert atmosphere at 300 °C gives full regeneration of the catalyst activity at low temperature reaction but only its partial reducing at high reaction temperature. The last case is connected with transformation of chemisorbed charged oxygen species into CO groups.

The KAU samples treated in flow of inert gas at 900–1000 °C were very active in H₂S oxidation to elemental sulfur transforming up to 51–57 mmol H₂S/g catalyst at 180 °C with formation of 1.7–1.9 g S_x/g catalyst.     

Oxidative conversion of methane to syngas over NiO/MgO solid solution supported on low surface area catalyst carrier

Influence of time-on-stream (0.5–15 h), CH₄/O₂ ratio in feed (1.8–8.0), space velocity (6000–510,000 cm³ g⁻¹ h⁻¹), catalyst particle size (22–70 mesh), and catalyst dilution by inert solid particles (diluent/catalyst weight ratio=4) on the performance at different temperatures (600–900°C) of the NiO/MgO solid solution deposited on SA-5205 [which is a low surface area macroporous silica-alumina catalyst carrier] in the oxidative conversion of methane to syngas (a mixture of CO and H₂) has been investigated. The dependence of conversion and selectivity on the space velocity is strongly influenced by the temperature. Both the conversion and selectivity for H₂ and CO are decreased markedly by increasing the CH₄/O₂ ratio in the feed. The catalyst dilution resulted in a small but significant decrease in both the conversion and selectivity for H₂ and CO. The increase in the catalyst particle size had also a small but significant effect on both the conversion and selectivity in the oxidative conversion process. Both the heat and mass transfer processes seem to play significant roles in the oxidative conversion of methane to syngas at a very low contact time or very high space velocity (5.1×10⁵ cm³ g⁻¹ h⁻¹).     

CO, H2 or C3H8 assisted catalytic combustion of methane over supported LaMnO3 monoliths

The effect of the addition of a second fuel such as CO, C₃H₈ or H₂ on the catalytic combustion of methane was investigated over ceramic monoliths coated with LaMnO₃/La-γAl₂O₃ catalyst. Results of autothermal ignition of different binary fuel mixtures characterised by the same overall heating value show that the presence of a more reactive compound reduces the minimum pre-heating temperature necessary to burn methane. The effect is more pronounced for the addition of CO and very similar for C₃H₈ and H₂. Order of reactivity of the different fuels established in isothermal activity measurements was: CO>H₂≥C₃H₈>CH₄. Under autothermal conditions, nearly complete methane conversion is obtained with catalyst temperatures around 800 °C mainly through heterogeneous reactions, with about 60–70 ppm of unburned CH₄ when pure methane or CO/CH₄ mixtures are used. For H₂/CH₄ and C₃H₈/CH₄ mixtures, emissions of unburned methane are lower, probably due to the proceeding of CH₄ homogeneous oxidation promoted by H and OH radicals generated by propane and hydrogen pyrolysis at such relatively high temperatures.

Finally, a steady state multiplicity is found by decreasing the pre-heating temperature from the ignited state. This occurrence can be successfully employed to pilot the catalytic ignition of methane at temperatures close to compressor discharge or easily achieved in regenerative burners.     

Catalytic combustion over platinum group catalysts: fuel-lean versus fuel-rich operation

Performance data are presented for methane oxidation on alumina-supported Pd, Pt, and Rh catalysts under both fuel-rich and fuel-lean conditions. Catalyst activity was measured in a micro-scale isothermal reactor at temperatures between 300 and 800 °C. Non-isothermal (near adiabatic) temperature and reaction data were obtained in a full-length (non-differential) sub-scale reactor operating at high pressure (0.9 MPa) and constant inlet temperature, simulating actual reactor operation in catalytic combustion applications.

Under fuel-lean conditions, Pd catalyst was the most active, although deactivation occurred above 650 °C, with reactivation upon cooling. Rh catalyst also deactivated above 750 °C, but did not reactivate. Pt catalyst was active above 600 °C. Fuel-lean reaction products were CO₂ and H₂O for all three catalysts.

The same catalysts tested under fuel-rich conditions demonstrated much higher activity. In addition, a ‘lightoff’ temperature was found (between 450 and 600 °C), where a stepwise increase in reaction rate was observed. Following ‘lightoff’ partial oxidation products (CO, H₂) appeared in the mixture, and their concentration increased with increasing temperature. All three catalysts exhibited this behavior.

High-pressure (0.9 MPa) sub-scale reactor and combustor data are shown, demonstrating the benefits of fuel-rich operation over the catalyst for ultra-low emissions combustion.     

Partial oxidation of alkanes to oxygenates in supercritical carbon dioxide

The catalytic partial oxidation of propane in supercritical carbon dioxide has been investigated in a stirred batch reactor. Various metals (oxides) have been used as supported catalysts with respect to their activity and selectivity for the formation of oxygenates. The reactions run with a 1:2.3–2.9:68–108 molar ratio of propane:synthetic air:CO₂ at 453–573 K and 80–100 bar. Using a precipitated 2.4 wt.% Co₃O₄–SiO₂ catalyst at 573 K, a total oxygenate (i.e. acetic acid, acetone, acetaldehyde, methanol) selectivity of 59% and a propene selectivity of 21% were obtained at a propane conversion of 12 mol%. The same catalyst has been used to investigate the influence of the supercritical conditions and initial feed composition on the reaction, varying the density of CO₂ and the concentration of synthetic air, respectively.     

Influence of cycle parameters on periodically operated fluidised bed reactor for CH4 autoreforming

Autothermal reforming of CH₄ has been studied under both periodic and steady state conditions. The investigation was conducted over Co–NiO in a fluidised bed reactor at 873 K and 101.32 kPa. Cycle periods of 1–40 min were used whilst the cycle split, S_ox (with respect to the O₂-rich cycle) was varied from 0.1 to 0.9. Generally, CH₄ oxidation stimulated CO formation, however, steam reforming yielded predominantly CO₂ and H₂. Although O₂-rich cycling (S_ox≥0.5) was detrimental to H₂ formation, H₂O-rich cycling resulted in a 15% improvement in steady state H₂ formation. Theoretical as well as experimental investigations pointed to a resonant frequency of about 6.7 mHz for CH₄ oxidation to produce super steady state H₂ yields. By periodic operation, it is possible to tune H₂/CO ratios over the range 2.5–7 for the same feed composition. Interestingly, S_ox=0.1 yielded the highest ratios, whereas the lowest ratios were attained at S_ox=0.9. Periodic composition cycling introduces a more flexible approach to reactor operation — H₂/CO can be easily modulated by varying the cycle parameters — compared to steady state operation.     

Dynamics of oxygen storage and release on commercial aged Pd-Rh three-way catalysts and their characterization by transient experiments

The present work has provided new fundamental information on the effects of aging (mileage, km) of a commercial Pd-Rh (9:1, w/w) three-way catalyst (TWC) on (a) the H₂ chemisorption, (b) the redox properties of washcoat material, and (c) the dynamic oxygen storage and release properties of TWC. Hydrogen chemisorption in the 25–400 °C range was found to decrease with increasing aging of TWC. On the other hand, H₂ chemisorption performed at 200 and 400 °C resulted in a significantly larger amount of chemisorbed hydrogen (exceeding the monolayer value based on the noble metals) compared to that obtained after chemisorption at 25 °C. This is due to the onset of a hydrogen spill over process in the 200–400 °C range. The features of H₂-TPD spectra were found to strongly depend on the aging of TWC. Hydrogen chemisorption at 25 °C followed by TPD after a given pre-treatment of the catalyst surface might be considered as a procedure for a good estimate of the metal dispersion of a commercial Pd-Rh TWC. The redox properties of the oxygen storage components of the washcoat of a commercial Pd-Rh TWC were found to drastically change with increasing aging of TWC. It was found that the oxygen storage capacity (OSC) of the TWC investigated decreases significantly with catalyst aging in the 0–56,000 km range and in the temperature range of 500–750 °C. In the case of fresh TWC, the presence of 20 ppm SO₂ or 10% CO₂ in a 1.5% O₂/He gas mixture used for oxygen storage (oxidizing gas) was found to result in a large decrease in the amount of dynamic OSC measured by alternating switches between oxidizing and reducing feed gas compositions. The shift in time of the peak maximum of the transient response of CO₂ obtained during the switch O₂/He → He → CO/He (t) can be ascribed to the alteration of the kinetics of the oxygen back-spillover process and not to the kinetics of CO oxidation on the metal surface.     

Catalytic reduction of NOx with H2/CO/CH4 over PdMOR catalysts

Conversion of NO_x with reducing agents H₂, CO and CH₄, with and without O₂, H₂O, and CO₂ were studied with catalysts based on MOR zeolite loaded with palladium and cerium. The catalysts reached high NO_x to N₂ conversion with H₂ and CO (>90% conversion and N₂ selectivity) range under lean conditions. The formation of N₂O is absent in the presence of both H₂ and CO together with oxygen in the feed, which will be the case in lean engine exhaust. PdMOR shows synergic co-operation between H₂ and CO at 450–500 K. The positive effect of cerium is significant in the case of H₂ and CH₄ reducing agent but is less obvious with H₂/CO mixture and under lean conditions. Cerium lowers the reducibility of Pd species in the zeolite micropores. The catalysts showed excellent stability at temperatures up to 673 K in a feed with 2500 ppm CH₄, 500 ppm NO, 5% O₂, 10% H₂O (0–1% H₂), N₂ balance but deactivation is noticed at higher temperatures. Combining results of the present study with those of previous studies it shows that the PdMOR-based catalysts are good catalysts for NO_x reduction with H₂, CO, hydrocarbons, alcohols and aldehydes under lean conditions at temperatures up to 673 K.     

Catalytic wet oxidation of phenol over PtxAg1−xMnO2/CeO2 catalysts

Catalytic wet oxidation reactions of aqueous phenol over unpromoted, base- and noble-metal promoted MnO₂/CeO₂ catalysts were carried out under mild conditions (80–130°C, 0.5 MPa O₂) in a batch slurry reactor. Even though the catalyst-mediated oxidation was very effective in destroying phenol, only a moderate selectivity toward complete mineralization into CO₂ and H₂O was attained due to parallel formation of deactivating carbonaceous deposits. Promotion of the mixed-oxide catalysts with platinum and/or silver enhanced the mineralization selectivity and reduced appreciably the amount of deposits.     

Combined CO2 reforming and partial oxidation of n-heptane on noble metal zirconia catalysts

The combined CO₂ reforming and partial oxidation (POX) of n-heptane was studied on various noble metal zirconia catalysts between 700 and 900 °C. The activity order of the metals was Rh > Pd > Ir > Pt. Selectivity to syngas increased with the activity of the catalysts but the H₂ to CO molar ratio decreased. The activity and selectivity of the 0.25 wt% Rh/ZrO₂ catalyst were close to the performance of a commercial 15 wt% NiO/Al₂O₃ catalyst. The conversions and product compositions were compared to the calculated thermodynamic equilibria.