宽角扫描偏置单反射面天线的面赋形设计

为实现宽角扫描,对偏置单反射面天线进行了面赋形设计,减少了天线在扫描过程中所需馈源阵单元的数目,或者说在馈源阵单元数目给定的情况下,赋形工作降低了波束扫描给天线带来的增益损失.赋形工作中,首先根据反射面的初始数据,以双三次B样条函数逼近其初始形状,然后从各预定的馈源位置向反射面发出若干条射线,并采用几何光学(GO)求得这些射线经反射面反射后的方向,最后以这些反射线的方向与各对应扫描方向之间的偏差最小为优化目标,通过Poweu方法对样条函数的插值数据点进行调节,最终确定了赋形反射面的形状.模拟结果表明了文中所述方法的可行性和有效性.     

双馈源双偏置结构星载通信多波束天线

为了使星载通信天线产生赋形波束的同时,又能辐射具有扫描特性的点波束满足特殊情形下的通信要求,提出了一种以单馈源赋形反射面天线为基础,利用另一个馈源进行副反射面赋形,补偿主反射面口径相位差的方法,从而形成高效率点波束,并通过副反射面及对应馈源横向偏焦实现点波束扫描的目的。为了检验方法的有效性,仿真实验了一副口径为2.2 m 的赋形反射面天线。实验结果表明:赋形波束在服务区内部的最小增益是30.0dBi,点波束在服务区内部及周边区域扫描时具有比赋形波束更高的增益,因此,所提方法是有效的。     

一种星载通信混合反射面天线的设计方法

为了使星载通信天线产生1个赋形波束覆盖服务区,同时产生1个固定点波束和1个有限扫描点波束,该文提出一种由2个赋形反射面和3个馈源组成的混合反射面天线。该天线是以赋形主反射面共用为基础,等效为2副单馈源单偏置反射面天线和1副双偏置格里高利型赋形反射面天线,分别产生赋形波束、固定点波束和有限扫描点波束。通过对一副口径为1.2 m的天线各个波束进行仿真实验,赋形波束在Ku收、发频段时波束覆盖区边缘(EoC)方向性系数为27.5 dBi,固定点波束在C收、发频段时天线口径效率高于70%,通过将赋形副反射面及对应馈源横向偏焦实现Ka收、发频段的点波束在服务区内外的扫描。仿真结果表明,该混合反射面天线可实现C/Ku/Ka频段的同时通信任务。     

反射面天线馈源喇叭边缘照射电平的分析

反射面天线设计的关键就是通过选择合适的喇叭馈源边缘照射电平以追求天线的高性能（增益,旁瓣电平, 效率等）。本文主要利用实例验证了标准反射面天线馈源喇叭的优选边缘照射电平,分析了赋形反射天线馈源喇叭的优选 边缘照射电平,给出了标准反射面和赋形反射面在设计中各自馈源喇叭的优选边缘照射电平。从而可以在设计工作中对 于不同形式的反射面天线有针对性的设计馈源喇叭的边缘照射电平。     

一种重新赋形副反射面的环焦天线设计

首先针对相同口径的环焦天线主反射面通用化需求,对双反射面天线的发展背景和环焦天线优点及赋形机理进行了简要介绍,然后提出了一种在不改变环焦天线的主反射面曲线的基础上,改变馈源照射角和重新赋形环焦天线副反射面曲线的设计方法,最后依据提出的设计方法给出了设计仿真计算,计算结果满足工程需求,避免了天线主反射面重新开模具,实现了环焦天线主反射面通用化,大大降低了天线的生产成本。     

基于实数编码遗传算法的多波束天线优化设计

为了在服务区内获得良好的多波束性能,提出了一种新的单口径单馈源多波束天线设计方法。通过采用对反射面进行赋形的方法来解决传统单口径单馈源多波束中交叠增益与旁瓣电平之间的矛盾。在对反射面优化的过程中将反射面的形变量作为优化变量,然后利用实数编码遗传算法对其进行优化从而实现更高的增益和载干比(C/ I)性能。最终利用该算法对一个服务区为某区域的多波束天线进行了优化设计和分析,仿真结果说明了该优化方法的有效性。     

宽角扫描侧馈偏置卡塞格伦天线的优化设计

为满足星载天线空间电扫描的要求,研究了宽角扫描侧馈偏置卡塞格伦天线(SFOC)的设计问题.给出了SFOC天线的结构形式,通过射线追踪的方法对SFOC的最佳馈源位置和最佳馈源指向进行了优化设计.二者的确定不仅改善了SFOC天线系统的扫描特性,而且提高了它的工程可实现性.分析结果表明,该SFOC天线在宽角扫描过程中,方向图畸变很小,增益损失和副瓣电平均达到了设计要求,从而为全球扫描星载天线的设计提供了有效的方案.     

Ku/Ka四波段共馈低剖面赋形天线设计

针对传统切换式多馈源的低剖面反射面天线结构复杂,不能多频段同时工作的问题,介绍了一款四波段单馈源低剖面环焦反射面天线及设计方法。该天线工作在四波段14~14.5 GHz, 11.45~12.75 GHz,19.6~21.2 GHz,29.4~31 GHz。整体天线采用双槽深波纹喇叭单馈源、通过口面场分布和多项式拟合过渡函数的方法构造的赋形副反射面和主反射面。用电磁仿真软件进行了建模仿真和验证。实测结果表明,整体天线较传统天线的效率提高12%以上,第一旁瓣<-14 dB,指标满足设计要求。     

遗传算法在星载数传天线优化设计中的应用

为使星载赋形反射面数传天线的增益满足指标要求,采用改进的实数编码遗传算法对其进行了优化设计。首先基于几何光学原理得到反射面中截线的初始形状,然后采用Newton插值函数对中截线进行拟合并把插值函数的系数作为优化变量,最终利用改进的遗传算法对优化变量进行调整来获得理想的赋形波束。为证明此方法的有效性,对一个X频段赋形反射面天线进行了优化设计,并与基于几何光学原理综合算法所得结果进行了对比。数值仿真结果表明:该方法不仅能够保证覆盖角域内任意一点的增益均高于设计指标要求,而且使天线在最大覆盖角度处的增益达到了7 dBi,提高了天线系统的性能。     

有限扫描反射面天线相控波束重构技术

该文研究一种采用聚焦馈源阵列馈电的反射面天线,相控阵馈源离开焦平面向反射面移动一定距离,位于焦散区,能够增强反射面天线的波束重构赋形能力和有限视角扫描能力。采用改进的投影矩阵法,利用仅相位控制技术,求解相控阵馈源的激励系数,有效综合了聚焦馈源偏置抛物面天线的方向图。对算例的设计达到了采用仅相位技术控制波束指向、波束赋形、旁瓣电平等性能要求,实现了相控阵馈电偏置抛物面天线的波束重构或扫描,并利用商用GRASP仿真软件验证了该文的设计结果,说明了该文方法的有效性。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

A rigorous proof of MIMO channel capacity’s increase with antenna number

It is well known that adding more antennas at the transmitter or at the receiver may offer larger channel capacity in the multiple-input multiple-output（MIMO） communication systems. In this letter, a simple proof is presented for the fact that the channel capacity increases with an increase in the number of receiving antennas. The proof is based on the famous capacity formula of Foschini and Gans with matrix theory.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks