Facile modified synthesis and intermediate temperature electrical properties of Sn0.95Al0.05P2O7/KSn2(PO4)3 composite electrolyte

In this study, Sn_0.95Al_0.05P₂O₇ and a novel dense Sn_0.95Al_0.05P₂O₇/KSn₂(PO₄)₃ composite electrolytes were synthesized. The structural characterization of X–ray diffraction (XRD) and microstructual properties of scanning electron microscopy (SEM) were carried out. The XRD results indicated that an in-situ reaction between Sn_0.95Al_0.05P₂O₇ and inorganic melt salt take place to form the Sn_0.95Al_0.05P₂O₇/KSn₂(PO₄)₃ composite. The intermediate temperature electrical properties were determined by using impedance spectroscopy, oxygen concentration cell and hydrogen concentration discharge cell. Finally, the H₂/O₂ fuel cell using the Sn_0.95Al_0.05P₂O₇/KSn₂(PO₄)₃ as electrolyte membrane was constructed and the obtained maximum power output densities were 67.7 mW cm^?2 and 142.1 mW cm^?2 at 650 °C and 700 °C, respectively.     

Interfacial origin of enhanced energy density in SrTiO3-based nanocomposite films

SrTiO₃-based films doped with different Al-precursors were prepared by sol-gel methods and the dielectric strengths and leakage currents of the materials were investigated. The best performance was found in SrTiO₃ films doped with Al₂O₃ nanoparticles (nano-Al₂O₃). When 5 mol% of nano-Al₂O₃ was added to SrTiO₃ films with Al electrodes, the dielectric strength was enhanced to 506.9 MV/m compared with a value of 233.5 MV/m for SrTiO₃ films. The energy density of the 5 mol% nano-Al₂O₃ doped SrTiO₃ films was 19.3 J/cm³, which was also far higher than that of the SrTiO₃ films (3.2 J/cm³). These results were attributed to interfacial anodic oxidation reactions, which were experimentally confirmed by cross-sectional transmission electron microscope studies and theoretically modelled based on Faraday's laws. The films with added nano-Al₂O₃ featured many conducting paths at the interfaces between the host phase and the guest nano-Al₂O₃, which promoted ion transport and contributed to the strong anodic oxidation reaction capability of the 5 mol% nano-Al₂O₃ doped SrTiO₃ films.     

Fabrication and performance of dielectric tape based on CaO-B2O3-SiO2 glass/Al2O3 for LTCC applications

A non-aqueous tape-casting process for fabricating CaO-B₂O₃-SiO₂ glass/Al₂O₃ dielectric tape for LTCC applications was investigated. An isopropanol/ethanol/xylene ternary solvent-based slurry was developed by using castor oil, poly(vinyl butyral), and dibutyl phthalate as dispersant, binder, and plasticizer, respectively. The effects of dispersant concentration, binder content, plasticizer/binder ratio, and solid loading, on the properties of the casting slurry and resultant tape were systematically investigated. The results showed that the optimal values for the dispersant and binder contents, plasticizer/binder ratio, and solid loading were 2.0 wt%, 7.5 wt%, 0.6, and 62 wt%, respectively. The resultant flexible and uniform, 120-μm-thick CaO-B₂O₃-SiO₂ glass/Al₂O₃ tape had a density of 1.90 g/cm^?3, tensile strength of 1.66 MPa, and average surface roughness of 310 nm. Laminated tapes sintered at 875 °C for 15 min exhibited excellent properties: relative density of 97.3%, ε_r of 7.98, tan δ of 1.3 × 10^?3 (10 MHz), flexural strength of 205 MPa, and thermal expansion coefficient of 5.47 ppm/°C. The material demonstrated good chemical compatibility with Ag electrodes, indicating a significant potential in LTCC applications.     

Investigation on the anti-reduction mechanism of Ti4+ in high dielectric constant system Ca0.9La0.067TiO3 by doping with Al2O3

Ca_0.9La_0.067TiO₃ (abbreviated as CLT) ceramics doped with different amount of Al₂O₃ were prepared via the solid state reaction method. The anti-reduction mechanism of Ti⁴⁺ in CLT ceramics was carefully investigated. X-ray diffraction (XRD) was used to analyze the phase composition and lattice structure. Meanwhile, the Rietveld method was taken to calculate the lattice parameters. X-ray photoelectron spectroscopy (XPS) was employed to study the valence variation of Ti ions in CLT ceramics without and with Al₂O₃. The results showed that Al³⁺ substituted for Ti⁴⁺ to form solid solution and the solid solubility limit of Al³⁺ is near 1.11 mol%. Furthermore, the reduction of Ti⁴⁺ in CLT ceramics was restrained by acceptor doping process and the Q × f values of CLT ceramics were improved significantly. The CLT ceramic doped with 1.11 mol% Al₂O₃ exhibited good microwave dielectric properties: ε_r = 141, Q × f = 6848 GHz, τ_f = 576 ppm/°C.     

Fabrication of dense Ce0.9Mg0.1P2O7-PmOn composites by microwave heating for application as electrolyte in intermediate-temperature fuel cells

In the present work, we report a method of fabrication of dense 10 mol% Mg²⁺-doped cerium pyrophosphate-phosphate (Ce_0.9Mg_0.1P₂O₇-P_mO_n; CMP-P) composites by microwave heat-treatment of the preformed Ce_0.9Mg_0.1P₂O₇ substrates in the presence of phosphoric acid. The composite was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS). The microwave heating at 375 °C for 5 min resulted in the formation of dense CMP-P composites which retained most of the pyrophosphate phase. The electrical conductivity was extracted from the EIS data and for the CMP-P composite prepared by H₃PO₄ loading for 10 h and microwave heat-treatment for 5 min it was found to be >10^?2 S m^?1 in 100–250 °C range with a maximum of 0.062 S cm^?1 at 190 °C, which was significant for its application as electrolyte in intermediate temperature fuel cells.     

Study of structure and conductivity of Li3/8Sr7/16-3x/2LaxZr1/4Nb3/4O3 solid electrolytes

Li_3/8Sr_7/16-3x/2La_xZr_1/4Nb_3/4O₃ (x = 0, 0.05, 0.10, 0.15, 0.20) were synthesized using the conventional solid-state reaction method. In order to increase the vacancy concentration, La³⁺ was doped on the Sr²⁺ site. Crystal structures of doped samples were characterized by X-ray diffraction. Except, perovskite-type Li_3/8Sr_7/16-3x/2La_xZr_1/4Nb_3/4O₃ (x = 0, 0.05, 0.10, 0.15) samples were fabricated by heat treatment at 1250 °C, 1275 °C, 1275 °C and 1275 °C, respectively, for 15 h. Lattice sizes decreased with the increase of doping amounts because of the smaller ion radius of La³⁺ compared to that of Sr²⁺. Ionic conductivities of the samples were measured by AC impedance spectroscopy. The results showed that the ionic conductivity increases at first and then decreases with raising doping amounts and sintering temperatures. So the optimized composition Li_3/8Sr_7/16-3x/2La_xZr_1/4Nb_3/4O₃ (x = 0.05) sintered at 1275 °C was selected with the highest total conductivity of 3.33 × 10^?5 S cm^?1at 30 °C and an activation energy of 0.27 eV. Additionally, potentiostatic polarization test was used to evaluate the electronic conductivity. The optimal composition Li_3/8Sr_7/16-3x/2La_xZr_1/4Nb_3/4O₃ (x = 0.05) as a possible Li-ion conducting solid electrolyte has an electronic conductivity of only 8.39 × 10^?9 S cm^?1.     

Liquid-phase synthesis of SrCo0.9Nb0.1O3-δ cathode material for proton-conducting solid oxide fuel cells

A novel liquid-phase synthesis strategy is demonstrated for the preparation of the Nb-containing ceramic oxide SrCo_0.9Nb_0.1O_3-δ (SCN). In comparison with the traditional solid-state reaction (SSR) method, the liquid-phase synthesis route offers a couple of advantages, including a lower phase formation temperature and a smaller particle size of the SCN materials that are beneficial for applications as proton-conducting fuel cell cathode. With BaCe_0.4Zr_0.4Y_0.2O_3-δ (BCZY442) as the electrolyte and the SCN synthesized in this work as the cathode, a proton-conducting solid oxide fuel cell (SOFC) shows a peak power density of 348 mW cm^?2 at 700 °C, significantly higher than that of a SOFC fabricated with SCN cathode prepared using the SSR method, which can only deliver 204 mW cm^?2 at the same temperature. Additionally, this new synthesis strategy allows impregnation of Sr²⁺, Co³⁺and Nb⁵⁺ on the solid backbone in aqueous solution, further improving cell performance to reach a peak power density of 488 mW cm^?2 at 700 °C.     

Honeycomb-like NiCo2O4@Ni(OH)2 supported on 3D N−doped graphene/carbon nanotubes sponge as an high performance electrode for Supercapacitor

In order to increase the energy density of supercapacitor, a new kind electrode material with excellent structure and outstanding electrochemical performance is highly desired. In this article, a new type of three-dimensional (3D) nitrogen-doped single-wall carbon nanotubes (SWNTs)/graphene elastic sponge (TRGN?CNTs?S) with low density of 0.8 mg cm^?3 has been successfully prepared by pyrolyzing SWNTs and GO coated commercial polyurethane (PU) sponge. In addition, high performance electrode of the honeycomb-like NiCo₂O₄@Ni(OH)₂/TRGN-CNTs-S with core-shell structure has been successfully fabricated through hydrothermal method and then by annealing treatment and electrochemical deposition method, respectively. Benefited from 3D structural feature, the compressed NiCo₂O₄@Ni(OH)₂/TRGN-CNTs-S electrode exhibits high gravimetric and volumetric capacitance of 1810 F g^?1, 847.7 F cm^?3 at 1 A g^?1. The high rate performance and long-term stability was also obtained. Furthermore, an asymmetric supercapacitor using NiCo₂O₄@Ni(OH)₂/TRGN-CNTs-S cathode and NGN/CNTs anode delivered high gravimetric and volumetric energy density of 54 W h kg^?1 at 799.9 W kg^?1 and 37 W h L^?1 at 561.5 W L^?1. In summary, an excellent electrochemical electrode with new elastic 3D SWNTs/graphene supports and binder free pseudocapacitive materials was introduced.     

Manufacturing a high performance film of CaO-B2O3-SiO2 glass-ceramic powder with surface modification for LTCC application

The present work was oriented to develop a high-performance film for LTCC application through using a kind of silane coupling agent (SCA) to modify the CBS (CaO-B₂O₃-SiO₂) glass-ceramic powders in tape casting process. The coupling mechanism of the silane coupling agent interacting with the powders was illustrated in detail, and the optimum amount of additions was determined by the infrared transmittance and contact angle experiment. The rheological properties of suspensions, the compactness and tensile breaking strength of the green tape were texted by using a number of quantitative and qualitative instruments. Furthermore, when the green tapes sintered at 820 °C, the sintering characteristics and microwave properties of sintered body with different SCA additions was also analyzed. Based on the experimental results, it revealed that the powders modified by SCA with 1.5 wt% additions could induce the most excellent performance of film, with the density at 1.57 g/cm³ and the tensile strength at 2.57 MPa, possessing the highest density and best microwave properties of sintered body: the density of sintered body was 2.48 g/cm³, the dielectric constant and dielectric loss was ε_r = 5.93, tanδ=8 × 10^?4 at 12 Hz.     

Strontium doping effects on the characteristics of solution-processed aluminum oxide dielectric layer and its application to low-voltage-operated indium-gallium-zinc-oxide thin-film transistors

In this paper, we investigated the strontium doping effects on the electrical and physical characteristics of solution-processed aluminum oxide dielectric layer and its application to low-voltage-operated indium-gallium-zinc-oxide (IGZO) thin-film transistors (TFTs). With an optimized doping concentration of strontium (5 at%) in aluminum oxide (Al₂O₃), an oxide gate dielectric layer having a dielectric constant of ~7 and low leakage current characteristics (~4 × 10⁻⁷ A/cm² at 3 MV/cm) could be achieved by a solution process, which are comparably better than those of pristine Al₂O₃ film. The enhanced dielectric properties from strontium doping can be attributed to the change in the physical properties of Al₂O₃ film incorporated with strontium, providing charge relaxation of defect states in Al₂O₃ film. Also, since the strontium is highly reactive with oxygen, the strontium substitution through a doping leads to more strongly bound structure in an Al₂O₃ film without considerable lattice distortion. Using the strontium-doped aluminum oxide film as a gate dielectric layer, having a thickness less than 10 nm, solution-processed IGZO TFTs operating at ≤ 1 V were demonstrated showing a field-effect mobility of 1.74 ± 1.10 cm²/V s and an on-current level of ~10⁻⁵ A.     

Fabrication of porous Al2O3-based ceramics using ball-shaped powders by preceramic polymer process in N2 atmosphere

Porous Al₂O₃-based ceramics were successfully fabricated using ball-shaped powders by preceramic polymer process in N₂ atmosphere. These results showed that the amorphous Si-O-C ceramics were formed on the surface of ball-shaped Al₂O₃ particles by the pyrolysis of the silicone resin during sintering in N₂ atmosphere, which played a role in connecting the Al₂O₃ particles by forming the sintering necks. When the sintering temperatures increased from 1100 °C to 1600 °C, the formed Si-O-C ceramics still existed in the amorphous state and had no crystallization. Interestingly, the amorphous β-SiC formed at 1300 °C and its amount gradually increased with further increasing temperatures. The linear shrinkage rate of the samples varied from 0.49% to 0.73% and the weight loss rate increased from 2.01% to 10.77%. The apparent porosity remarkably varied with the range of 24.9% and 34.5%, as the bulk-density varied from 2.66 to 2.47 g/cm³. The bending strength gradually increased from 9.36 to 22.51 MPa with increasing temperatures from 1100 °C to 1500 °C, however, the bending strength remarkably decreased at 1600 °C, which was attributed to the comprehensive function of the high porosity, broken Al₂O₃ particles and weak connection between Al₂O₃ particles in the samples.     

Highly efficient La0.8Sr0.2MnO3-δ - Ce0.9Gd0.1O1.95 nanocomposite cathodes for solid oxide fuel cells

La_0.8Sr_0.2MnO_3-δ-Ce_0.9Gd_0.1O_1.95 (LSM-CGO) nanostructured cathodes are successfully prepared in a single process by a chemical spray-pyrolysis deposition method. The cathode is composed of nanometric particles of approximately 15 nm of diameter, providing high triple-phase boundary sites for the oxygen reduction reactions. A low polarization resistance of 0.046 Ω cm² is obtained at 700 °C, which is comparable to the most efficient cobaltite-based perovskite cathodes. A NiO-YSZ anode supported fuel cell with the nanostructured cathode generates a power output of 1.4 W cm^?2 at 800 °C, significantly higher than 0.75 W cm^?2 for a cell with conventional LSM-CGO cathode. The results suggest that this is a promising strategy to achieve high efficiency electrodes for Solid Oxide Fuel Cells in a single preparation step, simplifying notably the fabrication process compared to traditional methods.     

Effects of Tb doping on structural and electrical properties of 47(Ba0.7Ca0.3)TiO3–0.53Ba(Zr0.2Ti0.8)O3 thin films at various annealing temperature by pulsed laser deposition

The ceramic thin films of 47(Ba_0.7Ca_0.3)TiO₃–0.53Ba(Zr_0.2Ti_0.8)O₃ (BCZT) + x (x = 0.2, 0.3, 0.4 and 0.5) mol% Tb were grown on Pt(111)/Si substrates with various annealing temperature by pulsed laser deposition. The XRD spectra confirm that Tb element can enhance the (l10) and (111) orientations in ceramic films. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) images show that Tb-doping can increase particle size effectively. The surface of Tb-doped film annealed at 800 ℃ is uniform and crack-free, and the average particle size and mean square roughness (RMS) are about 280 nm and 4.4 nm, respectively. Comparing with pure BCZT, the residual polarization (P_r) of 0.4 mol% Tb-doped film annealed at 800 ℃ increase from 3.6 to 9.8 μC/cm². Moreover, the leakage current density value of Tb doped films are one order of magnitude (5.33 × 10^?9?1.97 × 10^?8 A/cm² under 100 kV/cm) smaller than those of pure BCZT films (1.02 × 10^?7 A/cm²).     

Processing,microstructure and performance of Al2O3/Er3Al5O12/ZrO2 ternary eutectic ceramics prepared by laser floating zone melting with ultra-high temperature gradient

Directionally solidified Al₂O₃/Er₃Al₅O₁₂(EAG)/ZrO₂ ternary eutectic/off-eutectic composite ceramics with high density, homogeneous microstructures, well-oriented growth have been prepared by laser floating zone melting at different solidification rates from 4 to 400 µm/s. Uniform and stable melting zone is obtained by optimizing temperature field distribution to keep continuous and stable eutectic growth and prevent from cracks and defects. The as-solidified composite ceramic exhibits complexly irregular eutectic structure, in which the eutectic spacing is rapidly refined but dotted ZrO₂ number inside Al₂O₃ phase is decreased as increasing the solidification rate. The formation mechanism of ZrO₂ distributed inside Al₂O₃ matrix is revealed by examining the depression of solid/liquid interface. Furthermore, after heat exposure 1500 °C for 200 h, the eutectic microstructure only shows tiny coarsening, which indicates it has excellent microstructural stability. As increasing the ZrO₂ content, the fracture toughness can be improved up to 3.5 MPa m^1/2 at 20.6 mol% ZrO₂.     

Effects of TiO2 addition on dielectric and energy storage properties of BaO-K2O-Nb2O5-SiO2 glass ceramics

In this work, 25.6BaO-6.4K₂O-32Nb₂O₅-36SiO₂-xTiO₂ (0 ≤ x ≤10 mol%) (BKNST) glass ceramics were synthesized by conventional melts and controllable crystallization method. The effects of different TiO₂ addition on the phase composition, dielectric and energy storage properties of BKNS glass ceramics were systematically evaluated. With the TiO₂ concentration increasing, a growing content of Ba₂TiO₄ phase was observed in the glass ceramics. The microstructures appeared to be homogenous and uniform with very low porosity through the addition of TiO₂, for which the maximal breakdown strength of 2112 kV/cm and the corresponding energy storage density of 9.48 J/cm³ were obtained with x = 7.5. The extremely low dielectric loss of less than 1‰ (25 °C, 100 kHz) and the obviously improved microstructure contributed to the increased breakdown strength. In addition, the discharge power density of the glass-ceramic capacitor (x = 7.5) was investigated using the RLC charge-discharge circuit and a relatively high value of 16 MW/cm³ at 300 kV/cm was obtained.     

Separation and characterisation of fused alumina obtained from aluminium-chromium slag

Aluminium-chromium slag is a by-product of the thermal reduction of aluminium during chromium smelting, which is generally considered solid waste with a low utilisation rate. In this work, a fused carbonisation reduction method has been proposed to separate the Al₂O₃ and Cr₂O₃ from the slag and produce fused alumina and chromium carbide materials for refractory applications. The thermodynamic parameters of this process were determined using a standard thermal analysis method. In the molten slag, Cr₂O₃ reacts with C to produce high-density chromium carbide, which effectively precipitates at the bottom of the reaction vessel, while Al₂O₃ is converted into the corundum phase during cooling. The results of chemical analysis showed that the Al₂O₃ content in fused alumina was greater than 95 wt%, while its main crystalline phase was the corundum with a bulk density of 3.57 g cm^?3, thermal conductivity of 6.4–7.4 W m^?1 K^?1 (at temperatures above 600 °C), and average thermal expansion coefficient of about 7.5–8.2 × 10^?6/°C (in the temperature range of 800–1300 °C).     

Thickness dependent growth and ferroelectric/dielectric properties of phase-pure 0.65Pb(Mg1/3Nb2/3)O3-0.35PbTiO3 thin film derived from a modified sol-gel process

Annealing parameter and thickness are two significant factors affecting microstructure and electrical performance of sol-gel derived 0.65Pb(Mg_1/3Nb_2/3)O₃?0.35PbTiO₃ (0.65PMN-0.35PT) thin film. In this paper, various durations are firstly selected for the investigations on annealing parameter of 0.65PMN-0.35PT thin film. Enhanced insulating and ferroelectric properties can be obtained for the film annealed for 1 min due to its phase-pure and homogeneous perovskite structure. Based on this, a series of 0.65PMN-0.35PT thin films with various thicknesses by modifying deposition layer are synthesized annealed for 1 min and the effects of thickness on crystalline, insulating, ferroelectric and dielectric properties are characterized. It reveals that thickness-dependent behavior can be noticed for 0.65PMN-0.35PT thin film with the results that the 8-layered film possesses a relative large remanent polarization (P_r) of 23.34 μC/cm², and reduced leakage current density of 10^?9 A/cm² with low dissipation factor (tanδ) of 0.03 can be achieved for the 14-layered film.     

High tunability in (1 1 0)-oriented BaZr0.2Ti0.8O3 (BTZ) lead-free thin films fabricated by pulsed laser deposition

Using a pulsed laser deposition method the BaZr_0.2Ti_0.8 O₃ (BTZ) lead–free thin films with a thickness of ~250 nm were grown on FTO, ITO and Pt–Si substrates, respectively. The analysis results of microstructural, dielectric properties and leakage current reveal that the thin films deposited on Pt–Si substrates are oriented growth along the (1 1 0) direction and exhibit the optimal performance characteristics. Calculations of figure of merit (FoM) and dielectric tunability display a maximum value of ~42.8 and ~68.5% at E = 400 kV/cm at room temperature, respectively. The excellent tunable properties, high dielectric constant (~635@ 100 kHz) and low leakage current density of (9.3 × 10^–8 A/cm² at 400 kV/cm) make the (1 1 0)–oriented BaZr_0.2Ti_0.8 O₃ thin film to be an attractive material for applications of tunable devices.     

Enhancing copper infiltration into alumina using spark plasma sintering to achieve high performance Al2O3/Cu composites

Al₂O₃/Cu (with 30 wt% of Cu) composites were prepared using a combined liquid infiltration and spark plasma sintering (SPS) method using pre-processed composite powders. Crystalline structures, morphology and physical/mechanical properties of the sintered composites were studied and compared with those obtained from similar composites prepared using a standard liquid infiltration process without any external pressure. Results showed that densities of the Al₂O₃/Cu composites prepared without applying pressure were quite low. Whereas the composites sintered using the SPS (with a high pressure during sintering in 10 min) showed dense structures, and Cu phases were homogenously infiltrated and dispersed with a network from inside the Al₂O₃ skeleton structures. Fracture toughness of Al₂O₃/Cu composites prepared without using external pressure (with a sintering time of 1.5 h) was 4.2 MPa m^1/2, whereas that using the SPS process was 6.5 MPa m^1/2. These toughness readings were increased by 18% and 82%, respectively, compared with that of pure alumina. Hardness, density and electrical resistivity of the samples prepared without pressure were 693 HV, 82.5% and 0.01 Ω m, whereas those using the SPS process were 842 HV, 99.1%, 0.002 Ω m, respectively. The enhancement in these properties using the SPS process are mainly due to the efficient pressurized infiltration of Cu phases into the network of Al₂O₃ skeleton structures, and also due to high intensity discharge plasma which produces fully densified composites in a short time.     

Li ion conduction of perovskite Li0.375Sr0.4375Ti0.25Ta0.75O3 and related compounds

In this work, perovskite-structured Li_0.375Sr_0.4375M_0.25N_0.75O₃ (M=Ti, Sn, N=Nb, Ta) solid electrolytes were synthesized by conventional solid state reaction method. Phase compositions, fractured morphologies and conductivities of these compounds were investigated by X-ray diffraction, scanning electron microscope and AC-impedance spectroscopy, respectively. X-ray diffraction analysis confirms that all of Li_0.375Sr_0.4375M_0.25N_0.75O₃ (M=Ti, Sn, N=Nb, Ta) ceramics present perovskite structure. Pure Li_0.375Sr_0.4375Ti_0.25Ta_0.75O₃ and Li_0.375Sr_0.4375Sn_0.25Ta_0.75O₃ perovskite ceramics were obtained. But impurities were detected in Li_0.375Sr_0.4375Ti_0.25Nb_0.75O₃ and Li_0.375Sr_0.4375Sn_0.25Nb_0.75O₃. Among all investigated compounds, Li_0.375Sr_0.4375Ti_0.25Ta_0.75O₃ shows the highest total ionic conductivity of 2.60 × 10^?4 S cm^?1 at room temperature and the lowest activation energy of 0.347 eV. Conductivities of Li_0.375Sr_0.4375Sn_0.25Ta_0.75O₃ and Li_0.375Sr_0.4375Sn_0.25Nb_0.75O₃ were 4.4 × 10^?5 S cm^?1 and 1.82 × 10^?6 S cm^?1, respectively. Their conductivities were much lower than Li_0.375Sr_0.4375Ti_0.25Ta_0.75O₃ and Li_0.375Sr_0.4375Ti_0.25Nb_0.75O₃.