Experimental study on high temperature performances of silica-based ceramic core for single crystal turbine blades

Silica-based ceramic cores are widely utilized for shaping the internal cooling canals of single crystal superalloy turbine blades. The thermal expansion behavior, creep resistance, and high temperature flexural strength are critical for the quality of turbine blades. In this study, the influence of zircon, particle size distribution, and sintering temperature on the high-temperature performance of silica-based ceramic cores were investigated. The results show that zircon is beneficial for narrowing the contraction temperature range and reducing the shrinkage, improving the creep resistance and high-temperature flexural strength significantly. Mixing coarse, medium and fine fused silica powders in a ratio of 5:3:2, not only reduced high temperature contraction, but effectively improved the creep resistance. Properly increasing the sintering temperature can slightly reduce the thermal deformation and improve the high-temperature flexural strength of the silica-based core, but excessively high sintering temperature negatively impacts the creep resistance and high-temperature flexural strength.     

Scintillation,TSL and RPL properties of MgF2 transparent ceramic and single crystal

We have prepared MgF₂ transparent ceramics by spark plasma sintering (SPS) and investigated the scintillation and dosimeter properties compared with those of a single crystal. Under X-ray irradiation, a transparent ceramic showed scintillation with a broad feature over 300–600 nm with decay times of 310 and 1940 μs while the single crystal did not show such emission. It was found that MgF₂ show radio-photoluminescence (RPL), which is a generation of new luminescence center by ionizing radiation. The RPL was only observed in the transparent ceramic samples, which appeared as two emission bands peaking around 415 and 700 nm under 340±40 nm excitation. During the PL reading, the emission band at 415 nm effectively increased over 50 s. This result suggested that the RPL in MgF₂ shows a build-up phenomenon. From PL emission/excitation characteristics and decay time, it was suggested that the RPL peak around 415 nm was due to M(C_2h) center.     

Improved mechanical properties of SiB6 reinforced silica-based ceramic cores fabricated by 3D stereolithography printing

Silica-based ceramic core is an extremely critical component in the manufacture of hollow blades during investment casting. However, the traditional preparation methods rely more on the molds, and the manufacturing costs are relatively high. In this study, silica-based ceramics with silicon hexaboride (SiB₆) addition were prepared via 3D stereolithography printing. And the effects of the SiB₆ content on mechanical properties of the obtained ceramic samples were explored. As the SiB₆ content increased to 2.0 wt%, the linear shrinkage gradually decreased, while the room temperature and high temperature flexural strength were enhanced at the SiB₆ content from 0 to 1.0 wt% and reduced as the SiB₆ content further rose. As the SiB₆ content increased to 1.0 wt%, the linear shrinkage was reduced to 1.86% resulting from the oxidation reaction of SiB₆. Furthermore, with 1.0 wt% SiB₆ addition, the flexural strength of the samples at room temperature was enhanced from 6.75 MPa to 14.63 MPa due to the sintering promotion of oxidation product B₂O₃, and the flexural strength at 1550 °C was improved from 7.68 MPa to 13.08 MPa because of the enhanced β-cristobalite content, which is suitable for high temperature casting of ceramic cores. Therefore, it demonstrates the capability of fabricating SiB₆ reinforced silica-based ceramic cores with high performance via stereolithography.     

Effects of heat treatment on microstructure and mechanical properties of TiC/TiB composite bioinert ceramic coatings in-situ synthesized by laser cladding on Ti6Al4V

To improve the wear resistance of titanium alloy, in this work, TiC/TiB composite bioinert ceramic coatings were synthesized in-situ via laser cladding using Ti and B₄C mixed powders as precursor materials. And to decrease the impact of the excessive residual tensile stress generated by the uneven temperature distribution on the performance of coatings, the coatings were then subsequently heated for 3 h at different temperatures (400 °C, 600 °C, and 800 °C) and then air cooled. The effects of heat treatment on the microstructure, residual stress, micro-hardness, fracture toughness, and wear resistance of the coatings were investigated. The results showed that phase compositions and microstructure of the heat-treated coatings were virtually identical to that of the untreated coatings; however, the precipitation of acicular TiB enhanced mechanical properties of the heat-treated coatings. In addition, the average residual tensile stress values of the coatings decreased as the heat treatment temperature increased, which improved fracture toughness of the coatings from 3.95 to 4.68 MPa m^1/2. Moreover, wear resistance of the coatings was greatly enhanced by heat treatment; as the wear volume of the heat-treated coatings decreased by 50% at 800 °C compared with that of the untreated coatings. Lastly, the coatings showed good biocompatibility after being evaluated in vitro, and therefore had broad application prospects in the field of orthopedic implants.     

Influence of silicon carbide as a mineralizer on mechanical and thermal properties of silica-based ceramic cores

Ceramic cores have been designed with compounds based on fused silica due to its excellent thermal stability and chemical inertness against molten metals. To endure the high temperatures present during investment casting, mineralizers have been widely used to enhance the flexural strength and shrinkage of ceramic cores. In this study, we demonstrated a silica-based ceramic core with silicon carbide as a mineralizer for improving the mechanical and thermal properties. The SiC in the silica-based ceramic cores can enhance the mechanical properties (i.e., flexural strength and linear shrinkage) by playing a role as a seed for the crystallization of fused silica to cristobalite. The SiC also improves the thermal conductivity due to its higher value compared with fused silica. The results suggest that using the optimal amount of silicon carbide in silica-based ceramic cores can provide excellent mechanical properties of flexural strength and linear shrinkage and improved thermal conductivity.     

Reinforcement of silica-based ceramic cores based on amorphous and polycrystalline mullite fibers

In the investment casting of turbine blades, ceramic cores are key components to form complex hollow structures. Superior mechanical property and leaching rate are demanded for ceramic cores. Herein, ceramic cores were fabricated using fused silica powders as the matrix, and amorphous and polycrystalline mullite fibers as the reinforcement phases, respectively. The microstructure and property evolution of ceramic cores rely on the crystallization degree of mullite fibers are explored. Both of the mullite fibers lead to improved crystallization of cristobalite, reduced sintering shrinkage, increased apparent porosity, and benefited bending strength, creep resistance, and leaching rate of the cores. Compared to the polycrystalline mullite fibers, the amorphous fibers are metastable with large quantities of structural defects, promoting the diffusion mass transfer and forming strong interface between fibers and matrix. Therefore, the amorphous fibers have larger promotion on the bending strength and resistance to creep deformation of ceramic cores. Moreover, the structural defects of amorphous fibers ensures the high chemical activity in alkaline solutions and exhibits excellent leaching rate. The ceramic core with 4.5 wt% of amorphous mullite fibers exhibits excellent comprehensive performance with bending strengths of 28.9 MPa and 23.8 MPa at room temperature and 1550 °C, creep deformation of 0.3 mm, and leaching rate of 1.4 g/min, well meeting the casting requirements of hollow blades.     

Enhanced thermal properties of silica-based ceramic cores prepared by coating alumina/mullite on the surface of fused silica powders

In this study, an alumina/mullite coating was synthesized on the surface of fused silica powders to form an alumina/mullite-silica core-shell structure. The effects of the alumina/mullite coating on the cristobalite crystallization, thermal properties, and leachability of the silica-based ceramic cores were investigated using the simulated casting process. The X-ray diffraction results indicated that the crystallization of cristobalite was significant at the simulated casting temperature of approximately 1400 °C. An increase in the cristobalite content during this stage resulted in a large thermal expansion because of its higher coefficient of thermal expansion compared with that for fused silica. The addition of optimum amounts of the alumina/mullite powders resulted in an increase in the initial shrinkage temperature and a decrease in the shrinkage of the specimens. When the coating powders were added at 43 wt%, the initial shrinkage temperature increased from 1092 °C to 1200 °C and the shrinkage decreased sharply. Leaching tests showed that the silica-based ceramic cores were removed in the form of stripped layers. The washing and shaking process accelerated the disintegration of the ceramic core and improved its leachability.     

Properties of alumina coatings prepared on silica-based ceramic substrate by plasma spraying and sol-gel dipping methods

Silica-based ceramic cores are widely used in the manufacturing of hollow, nickel-based, superalloy turbine blades. However, elemental Hf, Ti, Al, and other active metals in the superalloy can react with silica-based ceramic cores during casting, resulting in a reduction in the quality of the turbine blades. In this study, both plasma spraying and sol-gel dipping methods were used to prepare alumina coatings on silica-based ceramic substrates to prevent the interfacial reaction. The performance of the alumina coatings prepared by both methods was evaluated by comparative analysis of the surface roughness, bonding interface morphologies, and the adhesive characteristics of the coating. The plasma-sprayed alumina coating has a roughness greater than 5 μm and peeled away from the substrate due to the difference in thermal expansion between SiO₂ and Al₂O₃ at temperatures above 1500 °C, rendering the silica-based substrate with the plasma-sprayed alumina coating unfit for the application requirements of the casting process. The alumina coating prepared by the sol-gel dipping method improved the roughness of the substrate from Ra 2.39 μm to Ra 1.83 μm, and no peeling was observed when heated to 1550 °C for 30 min due to the pinning characteristics of the coating on the substrate. Furthermore, the interfacial reaction between the DZ125 superalloy melt and the silica-based substrate coated with alumina by sol-gel dipping method were investigated. The alumina coating effectively inhibited the interfacial reaction and no reaction products were detected during the directional solidification with pouring temperature of 1550 °C and withdraw rate of 5 mm/min. While a uniform, 4–5 μm thick HfO₂ reaction layer formed between the uncoated substrate and the DZ125 alloy melt. Two dipping-drying cycles were required to ensure the alumina sol completely covered the surface of the substrate.     

Microstructure evolution and mechanical properties of ceramic shell moulds for investment casting of turbine blades by selective laser sintering

Ceramic shell moulds fabricated by traditional shell-making technology have relatively low strength, and often crack during the casting process due to the low strength. In addition, the traditional shell-making process requires long period and high cost. In this work, qualified mullite ceramic shell moulds with enhanced strength were fabricated by selective laser sintering (SLS) combined with high-temperature sintering process. The effects of SLS process parameters on dimensions were investigated, and process optimization was proposed by orthogonal experiments. The effect of sintering temperature on strength at room temperature and 900?°C were studied. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) analysis suggested that mullitization behavior was influenced by sintering temperature. Furthermore, the content of mullite phase, mullite grain sizes, and mean length-diameter ratio of the mullite grains increased with the sintering temperature. Mechanical testing results showed that the samples sintered at 1610?°C had an excellent compressive strength of 99.01?MPa at room temperature and over 172.02?MPa at 900?°C. These values far exceed those of ceramic shell moulds fabricated by the traditional shell-making process (40.43?MPa).     

Influence of debinding holding time on mechanical properties of 3D-printed alumina ceramic cores

Herein, alumina green bodies are fabricated by three dimensional (3D) printing technology, then, the influence of debinding holding time under vacuum and argon on mechanical properties is systematically investigated by comparing the changes in microstructure, bulk density, open porosity, grain connection situation and flexural strength of ceramics. The flexural strength of alumina ceramics acquired the maximum values of 26.4 ± 0.7 MPa and 25.1 ± 0.5 MPa after debinding under vacuum and argon for 120 min and 180 min, respectively. However, the alumina ceramics rendered the flexural strength of 19.4 ± 0.6 MPa and 9.5 ± 0.4 MPa under vacuum and argon without extended holding time, respectively. The relatively low mechanical properties can be mainly attributed to the weak interlayer binding force, which is caused by layer-by-layer forming mode during 3D printing process and anisotropic shrinkage during the sintering process. Moreover, the alumina ceramics exhibited moderate bulk density and open porosity of 2.4 g/cm³ and 42% after the sintering process, respectively, which are mainly influenced by the microstructural evolution of alumina ceramics during thermal treatment. Also, the diffusion of gases is achieved by curing of photosensitive resin and influenced by different holding times during debinding, affecting the mechanical properties of sintered ceramics. The mechanical properties of as-sintered ceramics are suitable for the utilization of ceramic cores in the manufacturing of hollow blades.     

Investigation on cristobalite crystallization in silica-based ceramic cores for investment casting

In this work, cristobalite crystallization and its effects on mechanical and chemical behaviour of injection moulded silica-based ceramic cores were investigated. In order to simulate casting process condition, the sintered samples at 1220 °C were also heated up to 1430 °C. Flexural strength test was carried out on both sintered and heat treated samples. Chemical resistance of the cores was evaluated by leaching the samples inside 43 wt% KOH solution at its boiling point. Phase evolution and microstructure were investigated by thermal analyses (DTA and DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM) and optical microscopy (OM). Results showed that cristobalite was crystallized on the surface of fused silica grains at about 1380 °C. Flexural strength of the sintered cores was decreased after simulated casting heat treatment due to cristobalite phase transformation. The formed cristobalite on the surface of fused silica grains dramatically decreased the leachability of ceramic cores.     

Effects of micro-sized mullite on cristobalite crystallization and properties of silica-based ceramic cores

Silica-based ceramic cores are extensively used in investment casting process, during which they must exhibit sufficient flexural strength and deformation resistance. In this study, micro-sized mullite was used as an additive to silica-based ceramic cores to optimize their high temperature properties. To investigate the effects of micro-sized mullite on cristobalite crystallization, mechanical and thermal properties of silica-based ceramic cores, ceramic cores with different amounts of micro-sized mullite were fabricated. The XRD results showed that additional micro-sized mullite diminished the crystallization of cristobalite at high temperatures, primarily caused by the mullite related compressive stresses on the surface regions of fused silica particles. Three-point bending tests and SEM results showed that micro-sized mullite had a more significant effect on the flexural strength of ceramic cores compared with conventional additives. Particularly, the fracture mechanism of silica-based ceramic cores had been changed from intergranular fracture into a mixed fracture consisting of both intergranular and transgranular fracture. The mechanical and thermal properties of ceramic cores were all reduced slightly as the mullite content exceed 4.6 wt%. Hence, to optimize the properties of silica-based ceramic cores, the micro-sized mullite content should not exceed 4.6 wt%.     

Fabrication processing and mechanical properties of Si3N4 ceramic turbocharger wheel

A composite technique was chosen to fabricate Si₃N₄ ceramic turbine wheel based on modified investment casting (MIC), slip casting (SP) and mold constraint hot isostatic pressing (MCHIP) aided by a near-net dimension using the gypsum mold and multi-piece Y₂O₃ ceramic mold. The detailed fabrication processing of Si₃N₄ ceramic turbine wheel was described. And the flexural strength and fracture toughness after different work temperature and speed were discussed. The results showed that owing to occurrence of phase transformation and chemical reaction, excess temperature resulted in interface cracking and interface debonding, flexural strength and fracture toughness decrease. Thermal expansion and centrifugal force under excessive high speed brought many pores in the microstructure and resulted in crack initiation and crack propagation. The critical work temperature was 700?°C and critical work speed was 100,000 r/min, which were obtained from the test and simulation results.     

Fabrication and mechanical properties of Al2O3-SiCw-TiCnp ceramic tool material

Whiskers and nanoparticles are usually used as reinforcing additives of ceramic composite materials due to the synergistically toughening and strengthening mechanisms. In this paper, the effects of TiC nanoparticle content, particle size and preparation process on the mechanical properties of hot pressed Al₂O₃-SiC_w ceramic tool materials were investigated. The results showed that the Vickers hardness and fracture toughness of the materials increased with the increasing of TiC content. The optimized flexural strength was obtained with TiC content of 4 vol% and particle size of 40 nm. The particle size has been found to have a great influence on flexural strength and small influence on hardness and fracture toughness. It was concluded that the flexural strength increased remarkably with the decreasing of the TiC particle size, which was resulted from the improved density and refined grain size of the composite material due to the dispersion of the smaller TiC particle size. SEM micrographs of fracture surface showed the whiskers to be mainly distributed along the direction perpendicular to the hot-pressing direction. The fracture toughness was improved by whisker crack bridging, crack deflection and whisker pullout; the TiC nanoparticles in Al₂O₃ grains caused transgranular fracture and crack deflection, which improved the flexural strength and fracture toughness with whiskers synergistically. Uniaxial hot-pressing of SiC whisker reinforced Al₂O₃ ceramic composites resulted in the anisotropy of whiskers’ distribution, which led to crack propagation differences between lateral crack and radical crack.     

Gelcasting of alumina based ceramic cores containing yttria for single crystal and directional solidification blades

Abstract

Ceramic cores play an essential role in investment casting. In this paper, gelcasting process has been successfully employed to fabricate alumina based ceramic cores containing yttria for single crystal and directional solidification blades. Based on an investigation of the formability of different ceramic slurries, material compositions of ceramic cores are determined by experiments. A proper sintering process is developed to get low sintered shrinkage, high apparent porosity and high room temperature flexural strength. The high temperature properties of ceramic cores are improved by dipping in water based yttria sol and resintering. The test results show that comprehensive properties of alumina based ceramic cores containing yttria fabricated by gelcasting are better than those of AC-1 ceramic cores made by the Beijing Institute of Aeronautical Materials, China, and that the ceramic cores can be applied to single crystal and directional solidification blade casting.     

Effects of heat treatment on the mechanical properties at elevated temperatures of plain-woven SiC/SiC composites

The effects of heat treatment on the mechanical properties of plain-woven SiC/SiC composites at 927 °C and 1200 °C in argon were evaluated through tensile tests at room temperature and at elevated temperature on the as-received and heat-treated plain-woven SiC/SiC composites, respectively. Heat treatment can improve the mechanical properties of composites at room temperature due to the release of thermal residual stress. Although heat treatment can damage the fiber, the effect of this damage on the mechanical properties of composites is generally less than the effect of thermal residual stress. Heat treatment will graphitize the pyrolytic carbon interface and reduce its shear strength. Testing temperature will affect the expansion or contraction of the components in the composites, thereby changing the stress state of the components. This study can provide guidance for the optimization of processing of ceramic matrix composites and the structural design in high-temperature environments.     

Polymer-derived SiHfN ceramics: From amorphous bulk ceramics with excellent mechanical properties to high temperature resistant ceramic nanocomposites

Within the present work, additive-free amorphous bulk SiHfN ceramics with excellent mechanical properties were prepared by a resource-efficient low-temperature molding method, namely warm-pressing. As densification mechanism viscous flow has been identified based on cross-linking reaction. The critical problems concerning gas evolution and crystallization inducing bloating and cracking are addressed through controlled thermolysis and pressure. The microstructural evolution of the SiHfN ceramics indicates that the incorporation of Hf in perhydropolysilazane not only increases the ceramic yield (97.4 wt%) and crystallization resistance (1300 °C), but also suppresses the transformation from α-Si₃N₄ to β-Si₃N₄ at high temperatures (1700 °C). Especially, HfN/α-Si₃N₄ nanocomposites converted by the SiHfN ceramics at 1500 °C show a slight weight loss of 3.13 wt%, indicating the high temperature resistance of the ceramic nanocomposites. The method proposed in this work opens a new strategy to fabricate additive-free polycrystalline Si₃N₄- and amorphous Si₃N₄-based (nano)composites.     

Effect of particle size on mechanical properties of alumina ceramic processed by photosensitive binder jetting with powder spattering technique

As an Additive Manufacturing technique, Binder Jetting enables the fabrication of customized and complex ceramic parts. However, the insufficiency of powder packing in green parts restricts the final products’ densifications and strengths. To form a layer of ceramic green parts, Photosensitive Binder Jetting with powder spattering technique provides entrapment of ceramic powder by printing of photo-curable resin and recoating by releasing the powder through a vibrating mesh. This recoating technique enables the processing of fine alumina powders, the average particle sizes of which are 3 μm, 1.65 μm, and their mixtures. Apparent densities, porosities, mechanical properties, and microstructures of the sintered parts were investigated. The alumina sample with the apparent density of 3.70 g/cm³, the compressive strength of 94.87 MPa, the biaxial strength of 50.06 MPa, and the porosity of 41.01 % was attained by the mixture with 70:30 wt.% of the 3 μm and 1.65 μm powders respectively.     

Influences of mullite fibers on mechanical and thermal properties of silica-based ceramic cores

Mullite fibers composite silica-based ceramic cores were successfully prepared by injection molding. The effects of mullite fibers on the mechanical and thermal properties of ceramic cores were investigated. The results indicated that the linear shrinkage was significantly decreased and the porosity was gradually increased with the increase of mullite fibers. In addition, the flexural strength for the room temperature and the simulated casting temperature of 1500°C was increased to a maximum value when the content of mullite fibers was about 1 wt.%, and then decreased with the increase of mullite fibers. The mullite fibers of 1 wt.% presented excellent mechanical properties with a linear shrinkage of .65%, a porosity of 6.96%, and a flexural strength of 17 MPa at room temperature and 34.83 MPa at the simulated casting temperature of 1500°C. Besides, the change in microstructure and properties in various contents of mullite fibers were analyzed.     

Influence of heat treatment on alternant-layer structure and mechanical properties of Al2O3-TiO2-MgO coatings

Al₂O₃-TiO₂-MgO ceramic alternant layer coatings were prepared by atmospheric plasma spraying and heat treated at 600, 700, 800, 900, and 1000?°C. The influence of heat treatment on microhardness, fracture toughness, and the structural evolution of the coatings on steel were investigated. Heat treatment promoted alternant layer interdiffusion within ceramic coatings, which could result a transformation from a lamellar morphology to mutual pinning. The interfacial diffusion between the bond coating and substrate was clearly demonstrated after heat treatment at different temperatures. Heat treatment also significantly affected the evolution of the hardness and fracture toughness. Temperature strongly affected the microhardness of the specimens, and the hardness arrived to the highest value at 1000?°C. The formation of a new Mg₂Al₆Ti₇O₂₅ phase and alternant layer mutual pinning were beneficial to hardness improvement, and heat treatment also significantly improved fracture toughness.