多组元BaO–SrO–CaO–MgO–Al2O3–2SiO2环境障涂层的制备与抗CaO–MgO–Al2O3–SiO2腐蚀性能

采用固相法制备不同摩尔 Ba、Sr、Ca、Mg 配比的 Ba O–Sr O–Ca O–Mg O–Al₂O₃–SiO₂ （BSCMAS）陶瓷材料,研究多组元陶瓷的制备工艺、显微结构及其抗 CMAS 腐蚀性能。结果表明：通过调控 MgO 的含量,在 1 400 ℃条件下制备了Ba_0.3Sr_0.3Ca_0.35Mg_0.05Al₂Si₂O₈ (B_0.3S_0.3C_0.35M_0.05AS)单相多组元陶瓷材料。在 1 250、1 300 ℃和 1 350 ℃对 B_0.3S_0.3C_0.35M_0.05AS 进行 CMAS 腐蚀实验,相比于 Ba_0.5Sr_0.5Al     

钛合金熔炼用Y2O3–Al2O3–MgO–CaO系耐火材料的设计与制备

坩埚耐火材料对钛合金熔炼的质量非常重要,为开发高性能新型坩埚材料,以工业Y₂O₃和Al₂O₃–MgO–CaO系粉末(AMC)为原料,制备出Y₂O₃–Al₂O₃–MgO–CaO系复合耐火材料,研究了烧结温度(1 500℃、1 600℃)和AMC含量(0、25%、50%、75%和100%,质量分数)对所制备耐火材料的物相组成、烧结性能(线收缩率、体积收缩率、显气孔率、体积密度)、常温耐压强度、抗热震性能和显微结构的影响。结果表明：相对于Y₂O₃和AMC材料,复合材料的性能均有所提高;提高烧结温度,其性能更佳;且随着AMC含量的提高,复合材料的线收缩率、体积收缩率、体积密度和常温耐压强度随之增大,显气孔率降低;当AMC的质量含量为75%时,1 500℃烧结3 h制得复合材料的综合性能最优,其显气孔率为4.37%,常温耐压强度为274.99 MPa,3次水冷热震后残余强度为16...     

Influence of Al2O3 whisker concentration on flexural strength of Al2O3(w)–ZrO2 (TZ-3Y) composite

On investigating the possibility of using alumina whisker reinforced 3 mol% Yttria stabilized Tetragonal Zirconia (TZ-3Y) composite for bioceramic applications, presented here is the influence of varying whisker concentration (2, 5, 10, 15 and 20 wt%) on flexural strength of the composite. Whiskers of hydrothermally synthesized Ammonium Aluminum Carbonate Hydroxide (AACH) were used for composite synthesis. These whiskers transformed in situ into alumina during sintering. It was found that with addition of alumina whiskers, strength was increased and reached a maximum value of 1212±60 MPa and 1325±65 MPa, in pure and 1 wt% CTAB added samples respectively, at a concentration of 10 wt% Al₂O₃ whiskers. The strength values of the synthesized composite can compete well with commercially available materials for dental applications.     

Crystallographic characterization of silicon nitride ceramics sintered with Y2O3–Al2O3 or E2O3–Al2O3 additions

Silicon nitride ceramics were sintered using Y₂O₃–Al₂O₃ or E₂O₃–Al₂O₃ (E₂O₃ denotes a mixed oxide of Y₂O₃ and rare-earth oxides) as sintering additives. The intergranular phases formed after sintering was investigated using high-resolution X-ray diffraction (HRXRD). The use of synchrotron radiation enabled high angular resolution and a high signal to background ratio. Besides the appearance of β-Si₃N₄ phase the intergranular phases Y₃Al₅O₁₂ (YAG) and Y₂SiO₅ were identified in both samples. The refinement of the structural parameters by the Rietveld method indicated similar crystalline structure of β-Si₃N₄ for both systems used as sintering additive. On the other hand, the intergranular phases Y₃Al₅O₁₂ and Y₂SiO₅ shown a decrease of the lattice parameters, when E₂O₃ was used as additive, indicating the formation of solid solutions of E₃Al₅O₁₂ and E₂SiO₅, respectively.     

Enhanced calcium–magnesium–aluminosilicate (CMAS) resistance of GdAlO3 (GAP) for composite thermal barrier coatings

The impact of calcium–magnesium–alumino-silicate (CMAS) degradation is a critical factor for development of new thermal and environmental barrier coatings. Several methods of preventing damage have been explored in the literature, with formation of an infiltration inhibiting reaction layer generally given the most attention. Gd₂Zr₂O₇ (GZO) exemplifies this reaction with the rapid precipitation of apatite when in contact with CMAS. The present study compares the CMAS behavior of GZO to an alternative thermal barrier coating (TBC) material, GdAlO₃ (GAP), which possesses high temperature phase stability through its melting point as well as a significantly higher toughness compared with GZO. The UCSB laboratory CMAS (35CaO–10MgO–7Al₂O₃–48SiO₂) was utilized to explore equilibrium behavior with 50:50 mol% TBC:CMAS ratios at 1200, 1300, and 1400°C for various times. In addition, 8 and 35 mg/cm² CMAS surface exposures were performed at 1425°C on dense pellets of each material to evaluate the infiltration and reaction in a more dynamic test. In the equilibrium tests, it was found that GAP appears to dissolve slower than GZO while producing an equivalent or higher amount of pore blocking apatite. In addition, GAP induces the intrinsic crystallization of the CMAS into a gehlenite phase, due in part to the participation of the Al₂O₃ from GAP. In surface exposures, GAP experienced a substantially thinner reaction zone compared with GZO after 10 h (87 ± 10 vs. 138 ± 4 μm) and a lack of strong sensitivity to CMAS loading when tested at 35 mg/cm² after 10 h (85 ± 13 versus 246 ± 10 μm). The smaller reaction zone, loading agnostic behavior, and intrinsic crystallization of the glass suggest this material warrants further evaluation as a potential CMAS barrier and inclusion into composite TBCs.     

含复合晶核剂CaO–MgO–Al2O3–SiO2微晶玻璃析晶与性能

采用高温熔制法制备了含复合晶核剂的CaO–MgO–Al2O3–SiO2(CMAS)微晶玻璃,并借助差热分析、X射线衍射、扫描电子显微镜分析了复合晶核剂组成对CMAS微晶玻璃的析晶和性能的影响规律。结果表明:复合晶核剂CaF2+TiO2能使CMAS玻璃的析晶活化能E降至329.2kJ/mol,且促进晶体快速生长;CaF2+P2O5可促进大量晶核生成,使晶体生长指数n增至2.87,从而实现CMAS玻璃整体析晶;CMAS微晶玻璃的主晶相为钙长石和透辉石,形状为长条状,TiO2和ZrO2的加入对主晶相种类和形状没有影响,但P2O5加入后玻璃不能析出透辉石晶相,而是辉石晶相,并产生许多细小晶粒;含复合晶核剂的微晶玻璃均具有较高Vicker硬度(7.0GPa以上),但引入CaF2+TiO2+P2O5时,微晶玻璃的Vicker硬度较低,这主要是晶粒排列不致密所致。     

Crystallization behavior and properties of K2O–CaO–Al2O3–SiO2 glass-ceramics

In order to obtain high-strength anorthite glass-ceramics, K₂O–CaO–Al₂O₃–SiO₂ quaternary glass and relevant glass-ceramics were prepared and investigated. The results show that anorthite along with kalsilite or leucite was precipitated from the parent glass. Kalsilite crystals were formed firstly and then converted into leucite through reacting with SiO₂ in the glass phase. The morphology of the crystals was dependent on the heat-treatment temperature. Column crystals were transformed into fine granular grains when the sintering temperature changed from 900 °C to 1100 °C. The activation energy (E_α) and avrami constant (n) were also calculated as 463.81 KJ/mol and 3.74 respectively, indicating that bulk nucleation and three-dimensional crystal growth were the dominating mechanisms in the temperature range 1000–1100 °C. The maximum value of the flexural strength for the glass-ceramics containing leucite was 248 MPa and the coefficient of thermal expansion (CTE) was in the range 5.69~11.94×10⁻⁶ K⁻¹. The leucite is the main reason for the high CTEs and high flexural strength of glass-ceramics.     

Effects of MgO micropowder on microstructure and resistance coefficient of Al2O3–MgO castable matrix

Development of lightweight refractories has been in high demand and the matrix of these materials is crucial for its slag resistance. This paper focuses on the relationship between the microstructure and the resistance coefficient of the Al₂O₃–MgO castables matrix. The permeability experiments were carried out, and the porous media model was adopted to describe both the viscous and inertial resistance. In addition, the effect of the MgO micropowder content is also discussed. Results indicate an improvement in the properties influenced by sintering such as bulk density and apparent porosity. Further, the pore size distribution range becomes narrower and the average pore size decreases when MgO micropowder content is fixed in the range 3–4.5 wt%. Moreover, the pore size is more crucial than the apparent porosity for the penetration resistance of the matrix. The relationship between the viscous resistance coefficient of the matrix and the microstructure parameters, fluid properties, and flow has been established to gain a better understanding of the slag penetration process.     

电熔镁砂在CaO–Al2O3–SiO2熔渣中的溶解行为

作为镁质耐火材料的重要原料,电熔镁砂在低密度高强钢精炼用CaO–Al₂O₃–SiO₂系熔渣中的溶解是影响炉衬使用寿命及钢质量的重要因素。本工作采用高温激光共聚焦显微观测系统研究了1 600℃下镁砂在该熔渣中的溶解行为,探究了镁砂颗粒的形状、质量及熔渣CaO和SiO₂质量分数比(即C/S)对其溶解行为的影响。结果表明：镁砂主要形状对其溶解速率影响较小;溶解速率随质量增大呈近线性下降,随C/S的增加而先降低后增加;镁砂颗粒的溶解曲线受质量影响更大,其溶解模型n值分别对应1/2、2/3、3/5,这为深入理解镁质耐火材料的渣蚀行为和提质优化提供指导。     

Spinelisation and properties of Al2O3–MgAl2O4–C refractory: Effect of MgO and Al2O3 reactants

The effect of particle size of MgO and Al₂O₃ on the spinel formation associated with permanent linear change on reheating (PLCR) and microstructure of Al₂O₃–MgAl₂O₄–C refractory is investigated as a function of heating cycle at 1600 °C with 2 h holding at each cycle. It was found that rate of spinel formation and associated volume expansion is very much dependent on the reactivity and particle size of the reactant. When the reactants are very fine and reactive there is considerable amount of spinel formation, whereas coarser reactants with lower reactivity show negligible formation of spinel phase and associated expansion. Magnesia and alumina with moderate reactivity develops optimum PLCR of the refractory. It continuously increases with the number of heating cycles. The SEM photomicrographs show that in Al₂O₃–MgAl₂O₄–C refractory the spinel phase is formed in between the calcined bauxite grain and the EDX analysis indicates that the spinel phase formed is stoichiometric in nature.     

Densification and characterization of SiO2B2O3CaOMgO glass/Al2O3 composites for LTCC application

A glass/ceramic composite using lead-free low melting glass (SiO₂B₂O₃CaOMgO glass) with Al₂O₃ fillers was investigated. X-ray diffraction analysis revealed that the anorthite and cordierite phase appeared in the sintered composites. The dilatometric analysis showed that the onset of shrinkage took place at ∼624 °C for all the samples and the onset temperature was independent on the content of glass. The low melting glass significantly promoted densification of the composites and lowered the sintering temperature to ∼875 °C. The addition of 50 wt% glass sintered at 875 °C showed ε_r of 7.3, tan δ of 1.15×10⁻³, TEC of 5.41 ppm/°C, thermal conductivity of 3.56 W/m °C, and flexural strength of 184 MPa. The results showed that the SiO₂B₂O₃CaOMgO glass/Al₂O₃ composites were strong potential candidates for low temperature cofired ceramic substrate applications.     

Effect of different nucleation catalysts on the crystallization of Li2O–ZnO–MgO–Al2O3–SiO2 glasses

Based on local raw materials, a range of LiZnMg aluminosilicate glasses were prepared to investigate the influence of TiO₂, Cr₂O_3, and ZrO₂ on the crystallization behaviour and thermal expansion characteristics. Differential thermal analysis showed that the crystallization propensity increases in the order TiO₂ > Cr₂O₃ > ZrO₂. Virgilite, β-spodumene ss, gahnite, enstatite and cristobalite were formed in the prepared glass-ceramics. The microstructure of glass-ceramic samples showed growths of rounded and subrounded grains in the base sample, whereas, somewhat rod-like and accumulated growths appeared in samples containing ZrO₂. However, a rather homogeneous texture of accumulated growths was developed in glass-ceramics containing TiO₂ and Cr₂O₃. The coefficient of thermal expansion of parent glasses was sensitive to the type of nucleating agent added (Cr₂O₃ > TiO₂ > ZrO₂) varying from 24.8 × 10⁻⁷ to 65.1 × 10⁻⁷ °C⁻¹ being almost unchanged with the heat-treatment. The microhardness values of glass-ceramic samples were in the 763–779 kg/mm² range.     

CaO–MgO–Al2O3–SiO2 (CMAS) corrosion behaviour of LaMgAl11O19/GdPO4 thermal barrier coating materials

CaO–MgO–Al₂O₃–SiO₂ (CMAS) corrosion poses serious hidden dangers for the application of thermal barrier coatings (TBCs). In this study, LaMgAl₁₁O₁₉ (LMA) and GdPO₄ were mixed at molar ratios of 2:1, 1:1 and 1:2 to prepare LMA/GdPO₄ materials, and the CMAS corrosion behaviours of these materials were investigated at 1300°C–1500 °C for 20 h and 40 h. It was demonstrated that temperature was the main factor influencing the corrosion behaviours and products. The materials were damaged at 1300 °C by the crystallization of CMAS melts to form CaAl₂Si₂O₈. In contrast, the materials were corroded by CMAS melts via the reaction between CMAS and GdPO₄ at 1500 °C. These results indicate that the addition of GdPO₄ to LMA can improve the resistance of the LMA material to CMAS corrosion.     

Influence of the synthesis process on the features of Y2O3-stabilized ZrO2 powders obtained by the sol–gel method

Y₂O₃-stabilized ZrO₂ (YSZ) powders have been prepared by the sol–gel method using different synthesis parameters. Specifically, zirconium n-propoxide was dissolved in propanol at pH 0.5 or 5 (provided by HNO₃), with or without acetic acid in the hydrolysis medium. Subsequently, the YSZ powders obtained by gelation and drying of these solutions was characterized using scanning and transmission electron microscopies, X-ray diffractometry, and N₂-adsorption. Compacts made from these YSZ powders which were then sintered were also analyzed. It was found that the pH of the hydrolysis medium has a notable influence on the microstructure, morphology, color, crystallinity, and sintering behavior process of these YSZ sol–gel powders. It was also found that the use of acetic acid also affects the YSZ powder features, and results in compacts with higher residual porosity after sintering. Finally, the compacts prepared from the YSZ powders obtained at pH 5 and without acetic acid exhibit the greatest sinterability.     

Composite wasteform based on SiO2–PbO–CaO–ZrO2–TiO2–(B2O3–K2O) parent glass with zircon as the second component

Many different types of glass and ceramic wasteforms have been investigated for nuclear waste immobilization. This study deals with synthesizing composite wasteforms based on a parent glass belonging to the SiO₂–PbO–CaO–ZrO₂–TiO₂–(B₂O₃–K₂O) system with the use of zircon as a second component. The fabrication involves powder mixing, pressing and pressureless sintering. The processing conditions were investigated so as to achieve the highest density and the best sintering temperature for different amounts of zircon, i.e. 5, 10 and 15 wt%. The sintered products were studied by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM); as well as ICP-MAS for leaching experiments. The most promising composite containing zirkelite and titanite crystals in a lead-rich glassy matrix was obtained at 700 °C for 10 wt% zircon.     

CaO/Y2O3共稳ZrO2复相陶瓷显微结构和力学性能研究

采用传统固相法制备了不同CaO和不同Y₂O₃掺杂量的ZrO₂复相陶瓷。借助XRD、SEM、EDS、维氏硬度计等测试手段研究了复相陶瓷的显微结构及力学性能。结果表明CaO/Y₂O₃共稳ZrO₂复相陶瓷的显微结构中共有大、中、小三种不同尺寸的ZrO₂晶粒。CaO的掺入在细化晶粒的同时可以降低中型t-ZrO₂晶粒内Y稳定剂含量,提高t-ZrO₂相变量;Y₂O₃能降低基体中m-ZrO₂的体积分数。当Y₂O₃掺入量为1.8 mol%,CaO掺入量为2 mol%时,获得了最高的断裂韧性(5.4±0.2 MPa·m^1/2);当Y₂O₃掺入量为2.5 mol%,CaO掺入量为1 mol%和2 mol%时,分别获得了最高的抗弯强度(78...     

Properties of sol–gel derived Al2O3–15 wt.% ZrO2 (3 mol% Y2O3) nanopowders using two different precursors

An alumina–15 wt.% zirconia (3 mol% yttria) nanopowder was synthesized by sol–gel method using salt and alkoxide as precursors. Al(NO₃)₃·9H₂O, ZrOCl₂·8H₂O and Y(NO₃)₃·6H₂O were used as salt precursors and Al(OC₄H₉)₃ and Zr(OC₄H₉)₄ were used as alkoxide precursors. The dried gels of two precursors were heat treated in the range of 450–1350 °C. The powders produced by alkoxide precursors calcined at 750 °C were in the range of 15–75 nm, while those prepared by salt precursors had the size in the range of 30–90 nm. The former powders had a higher surface area and smaller mean pore diameter compared with the later powder, i.e. 152 m²/g and 5.63 nm comparing with 121 m²/g and 9.79 nm, respectively. Therefore phase transformation in the former occurred in lower temperatures.     

添加Fe2O3、Al2O3和SiO2纳米粉对MgO烧结性能的影响

以烧结镁砂为主原料,分别以粒度20～60 nm的SiO2纳米粉、粒度20～40 nm的Fe2O3纳米粉和粒度50 nm的Al2O3纳米粉(纯度(w)均为99.9%)为添加剂,设计了添加剂加入量(w)分别为1%、3%、5%(其余为烧结镁砂)的9种试样。配料后,外加10%(w)的分散剂和5%(w)的丙酮,研磨10min后,以100 MPa压力制成2.54 mm×2.54 mm的试样,在电炉中以5℃.min-1的升温速度分别升温至1 300、1 500和1 620℃保温4 h,冷却后分析试样的体积密度、显气孔率、相     

The reaction between the magnesia–chrome brick and the molten slag of MgO–Al2O3–SiO2–CaO–FetO and the resulting microstructure

The reaction and microstructure at the interface of MgO–Cr₂O₃ brick and the molten slag of MgO–Al₂O₃–SiO₂–CaO–Fe_tO after static slag corrosion at 1823–1923 K for various times and the resulting microstructure were investigated and characterized. After the static slag corrosion at 1923 K for 4 h, the XRD results show the major phases of periclase MgO, MgCr₂O₄ spinel, and CaMgSiO₄ as the minor phase. MgCr₂O₄ phase causes MgO to form a discontinuous phase in MgO–Cr₂O₄ brick. After static slag corrosion at 1923 K for 4 h, SEM micrographs show that brick interior cracks, MgO and dissolved MgO. MgO dissolved due to the molten plag penetrated into the brick interior and reaction with it, leading to a localized dissolution of brick slag. TEM micrographs and ED patterns demonstrate that the minor phase of (Mg, Fe)(Al, Cr)₂O₄ precipitates in the MgCr₂O₄ matrix.