High-voltage normally off GaN MOSFETs on sapphire substrates

Gallium nitride self-aligned MOSFETs were fabricated using low-pressure chemical vapor-deposited silicon dioxide as the gate dielectric and polysilicon as the gate material. Silicon was implanted into an unintentionally doped GaN layer using the polysilicon gate to define the source and drain regions, with implant activation at 1100/spl deg/C for 5 min in nitrogen. The GaN MOSFETs have a low gate leakage current of less than 50 pA for circular devices with W/L=800/128 /spl mu/m. Devices are normally off with a threshold voltage of +2.7 V and a field-effect mobility of 45 cm/sup 2//Vs at room temperature. The minimum on-resistance measured is 1.9 m/spl Omega//spl middot/cm/sup 2/ with a gate voltage of 34 V (W/L=800/2 /spl mu/m). High-voltage lateral devices had a breakdown voltage of 700 V with gate-drain spacing of 9 /spl mu/m (80 V//spl mu/m), showing the feasibility of self-aligned GaN MOSFETs for high-voltage integrated circuits.     

$hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ Channel MOSFETs With Self-Aligned InAs Source/Drain Formed by MEE Regrowth

Abstract-We report Al₂O₃Zln_0.53Ga_0.47As MOSFETs having both self-aligned in situ Mo source/drain ohmic contacts and self-aligned InAs source/drain n⁺ regions formed by MBE regrowth. The device epitaxial dimensions are small, as is required for 22-nm gate length MOSFETs; a 5-nm In_0.53Ga_0.47As channel with an In_0.4sAl_0.52As back confinement layer and the n⁺⁺ source/drain junctions do not extend below the 5-nm channel. A device with 200-nm gate length showed I_D = 0.95 mA/mum current density at V_GS = 4.0 V and g_m = 0.45 mS/mum peak transconductance at V_DS = 2.0 V.     

Design and fabrication of RESURF MOSFETs on 4H-SiC(0001), (112~0), and 6H-SiC(0001)

Design and fabrication of lateral SiC reduced surface field (RESURF) MOSFETs have been investigated. The doping concentration (dose) of the RESURF and lightly doped drain regions has been optimized to reduce the electric field crowding at the drain edge or in the gate oxide by using device simulation. The optimum oxidation condition depends on the polytype: N/sub 2/O oxidation at 1300/spl deg/C seems to be suitable for 4H-SiC, and dry O/sub 2/ oxidation at 1250/spl deg/C for 6H-SiC. The average inversion-channel mobility is 22, 78, and 68 cm/sup 2//Vs for 4H-SiC(0001), (112~0), and 6H-SiC(0001) MOSFETs, respectively. RESURF MOSFETs have been fabricated on 10-/spl mu/m-thick p-type 4H-SiC(0001), (112~0), and 6H-SiC(0001) epilayers with an acceptor concentration of 1/spl times/10/sup 16/ cm/sup -3/. A 6H-SiC(0001) RESURF MOSFET with a 3-/spl mu/m channel length exhibits a high breakdown voltage of 1620 V and an on-resistance of 234 m/spl Omega//spl middot/cm/sup 2/. A 4H-SiC(112~0) RESURF MOSFET shows the characteristics of 1230 V-138 m/spl Omega//spl middot/cm/sup 2/.     

Improved high-voltage lateral RESURF MOSFETs in 4H-SiC

High-voltage lateral RESURF metal oxide semiconductor field effect transistors (MOSFETs) in 4H-SiC have been experimentally demonstrated, that block 900 V with a specific on-resistance of 0.5 Ω-cm² . The RESURF dose in 4H-SiC to maximize the avalanche breakdown voltage is almost an order of magnitude higher than that of silicon; however this high RESURF dose leads to oxide breakdown and reliability concerns in thin (100-200 nm) gate oxide devices due to high electric field (>3-4 MV/cm) in the oxide. Lighter RESURF doses and/or thicker gate oxides are required in SiC lateral MOSFETs to achieve highest breakdown voltage capability     

High-power-density 4H-SiC RF MOSFETs

The authors have made the first 4H-SiC RF power MOSFETs with cutoff frequency up to 12 GHz, delivering RF power of 1.9 W/mm at 3 GHz. The transistors withstand 200 V drain voltage, are normally off, and show no gate lag, which is often encountered in SiC MESFETs. The measured devices have a single drain finger and a double gate finger, and a total gate width of 0.8 mm. To their knowledge, this is the first time that power densities above 1 W/mm at 3 GHz are reported for SiC MOSFETs.     

High channel mobility in normally-off 4H-SiC buried channel MOSFETs

We have fabricated buried channel (BC) MOSFETs with a thermally grown gate oxide in 4H-SiC. The gate oxide was prepared by dry oxidation with wet reoxidation. The BC region was formed by nitrogen ion implantation at room temperature followed by annealing at 1500°C. The optimum doping depth of the BC region has been investigated. For a nitrogen concentration of 1×10¹⁷ cm^-3, the optimum depth was found to be 0.2 μm. Under this condition, a channel mobility of 140 cm²/Vs was achieved with a threshold voltage of 0.3 V. This channel mobility is the highest reported so far for a normally-off 4H-SiC MOSFET with a thermally grown gate oxide     

Formation of TiSi2 and shallow junction byAs+ ion-beam mixing and infrared rapid heat treatment

A technique for forming shallow junctions with low-resistance silicide contacts developed for the use in VLSI with scaled MOSFETs is discussed. The salicide (self-aligned silicide) MOSFET gate and source-drain features self-aligned refractory metal silicide and are isolated from one another even without any insulating spacer on the gate sides. A critical step in such a MOSFET fabrication process is the ion implantation through metal silicidation technique, which includes As⁺ ion-beam-induced titanium-silicon interface mixing and infrared rapid heat treatment to form simultaneously the n⁺-p junction and a high-quality TiN covered TiSi₂ contact layer     

An all implanted self-aligned enhancement mode n-JFET with Zn gatesfor GaAs digital applications

An all implanted self-aligned n-channel JFET fabrication process is described where Zn implantation is used to form the p⁺ gate region. A refractory metal (W) gate contact is used to allow subsequent high temperature activation of the self-aligned Si source and drain implant. 0.7 μm JFET's have a maximum transconductance of 170 mS/mm with a saturation current of 100 mA/mm at a gate bias of 0.9 V. The p⁺/n homojunction gate has a turn on voltage of 0.95 V at a current of 1 mA/mm. The drain-source breakdown voltage is 6.5 V. Microwave measurements made at a gate bias of 1 V show an f_t of 19 GHz with an f_max of 36 GHz. These devices show promise for incorporation in both DCFL and complementary logic circuits     

Lateral n-channel inversion mode 4H-SiC MOSFETs

Advances in MOS devices on silicon carbide (SiC) have been greatly hampered by the low inversion layer mobilities. In this paper, the electrical characteristics of lateral n-channel MOSFETs fabricated on 4H-SiC are reported for the first time. Inversion layer electron mobilities of 165 cm²/V·s in 4H-SiC MOSFETs were measured at room temperature. These MOSFETs were fabricated using a low temperature deposited oxide, with subsequent oxidation anneal, as the gate dielectric     

Hysteresis in transfer characteristics in 4H-SiCdepletion/accumulation-mode MOSFETs

Hysteresis in room-temperature transfer characteristics between forward (pinch-off voltage, V_P=-15 V) and reverse gate voltage sweeps (V_P=7 V) in n-channel depletion/accumulation-mode 4H-SiC MOSFETs is reported. Transfer characteristics exhibit a parallel shift toward negative voltages depending,on the starting gate voltage and direction of the sweep. The hysteresis and shift in transfer characteristics are related to changes in effective fixed-oxide charge resulting from changes in interface trap occupancy. Interface trap occupancy changes depending on the magnitude of the starting gate voltage and the direction of gate-voltage sweep. At high temperatures, the hysteresis between forward and reverse gate voltage sweep decreases     

Nitrogen Plasma Processing of SiO2/4H-SiC Interfaces

A nitrogen plasma annealing process for gate dielectric applications in 4H-SiC metal oxide semiconductor (MOS) technology has been investigated. This process results in substantially greater interfacial N coverage at the SiO₂/4H-SiC interface and lower interface trap densities than the state-of-the-art nitric oxide (NO) annealing process. Despite these exciting results, the field-effect mobility of MOS field-effect transistors (MOSFETs) fabricated by use of this process is very similar to that of NO-annealed MOSFETs. These results emphasize the importance of understanding mobility-limiting mechanisms in addition to charge trapping in next-generation 4H-SiC MOSFETs.     

An ITLDD CMOS process with self-aligned reverse-sequenceLDD/channel implantation

An advanced inverse-T LDD (ITLDD) CMOS process has been developed. This process features self-aligned lightly-doped-drain/channel implantation for improved hot-carrier protection. Selective polysilicon deposition is used to define the thick polysilicon gate regions with a thin polysilicon gate regions overlying the lightly doped n^- and p⁺ regions. Since the thick poly gate regions are defined by nitride sidewall spacers, optical lithography can be used to define sub-half-micrometer gate length MOSFETs. The LDD implants are performed after the n⁺ and p⁺ implants are annealed, resulting in MOSFET's with improved short-channel behavior due to the smaller lateral source/drain diffusion     

High field-effect mobility in n-channel Si face 4H-SiC MOSFETs with gate oxide grown on aluminum ion-implanted material

We report investigations of Si face 4H-SiC MOSFETs with aluminum (Al) ion-implanted gate channels. High-quality SiO/sub 2/-SiC interfaces are obtained both when the gate oxide is grown on p-type epitaxial material and when grown on ion-implanted regions. A peak field-effect mobility of 170 cm/sup 2//V/spl middot/s is extracted from transistors with epitaxially grown channel region of doping 5/spl times/10/sup 15/ cm/sup -3/. Transistors with implanted gate channels with an Al concentration of 1/spl times/10/sup 17/ cm/sup -3/ exhibit peak field-effect mobility of 100 cm/sup 2//V/spl middot/s, while the mobility is 51 cm/sup 2//V/spl middot/s for an Al concentration of 5/spl times/10/sup 17/ cm/sup -3/. The mobility reduction with increasing acceptor density follows the same functional relationship as in n-channel Si MOSFETs.     

SiC devices: physics and numerical simulation

The important material parameters for 6H silicon carbide (6H-SiC) are extracted from the literature and implemented into the 2-D device simulation programs PISCES and BREAKDOWN and into the 1-D program OSSI Simulations of 6H-SiC p-n junctions show the possibility to operate corresponding devices at temperatures up to 1000 K thanks to their low reverse current densities. Comparison of a 6H-SiC 1200 V p-n^--n⁺ diode with a corresponding silicon (Si) diode shows the higher switching performance of the 6H-SiC diode, while the forward power loss is somewhat higher than in Si due to the higher built-in voltage of the 6H-SiC p-n junction. This disadvantage can be avoided by a 6H-SiC Schottky diode. The on-resistances of Si, 3C-SiC, and 6H-SiC vertical power MOSFET's are compared by analytical calculations. At room temperature, such SiC MOSFET's can operate up to blocking capabilities of 5000 V with an on-resistance below 0.1 Ωcm², while Si MOSFET's are limited to below 500 V. This is checked by calculating the characteristics of a 6H-SiC 1200 V MOSFET with PISCES. In the voltage region below 200 V, Si is superior due to its higher mobility and lower threshold voltage. Electric fields in the order of 4×10⁶ V/cm occur in the gate oxide of the mentioned 6H-SiC MOSFET as well as in a field plate oxide used to passivate its planar junction. To investigate the high frequency performance of SiC devices, a heterobipolartransistor with a 6H-SiC emitter is considered. Base and collector are assumed to be out of 3C-SiC. Frequencies up to 10 GHz with a very high output power are obtained on the basis of analytical considerations     

Self-aligned GaAs MISFET's with a low-temperature-grown GaAs gateinsulator

GaAs MISFET's with a low-temperature-grown (LTG) GaAs gate insulator and ion-implanted self-aligned source and drain n⁺ regions are demonstrated. The resistivity and breakdown field of the LTG GaAs insulator were not changed appreciably by implantation and 800°C activation annealing. The gate leakage current remained very low at a value of approximately 1 μA per μm² of gate area at 3 V forward gate bias. Because of the reduced source and drain resistance, the drain saturation current and the transconductance of self-aligned MISFET's increased more than twofold after ion implantation     

Process integration and device performance of a submicrometerBiCMOS with 16-GHz ft double poly-bipolar devices

Submicrometer-channel CMOS devices have been integrated with self-aligned double-polysilicon bipolar devices showing a cutoff frequency of 16 GHz. n-p-n bipolar transistors and p-channel MOSFETs were built in an n-type epitaxial layer on an n⁺ buried layer, and n-channel MOSFETs were built in a p-well on a p⁺ buried layer. Deep trenches with depths of 4 μm and widths of 1 μm isolated the n-p-n bipolar transistors and the n- and p-channel MOSFETs from each other. CMOS, BiCMOS, and bipolar ECL circuits were characterized and compared with each other in terms of circuit speed as a function of loading capacitance, power dissipation, and power supply voltage. The BiCMOS circuit showed a significant speed degradation and became slower than the CMOS circuit when the power supply voltage was reduced below 3.3 V. The bipolar ECL circuit maintained the highest speed, with a propagation delay time of 65 ps for C_L=0 pF and 300 ps for C_L=1.0 pF with a power dissipation of 8 mW per gate. The circuit speed improvements in the CMOS circuits as the effective channel lengths of the MOS devices were scaled from 0.8 to 0.4 μm were maintained at almost the same ratio     

Excellent effects of hydrogen postoxidation annealing on inversionchannel mobility of 4H-SiC MOSFET fabricated on (112¯0) face

Effects of hydrogen postoxidation annealing (H₂ POA) on 4H-silicon carbide (SiC) MOSFETs with wet gate oxide on the (112¯0) face have been investigated. As a result, an inversion channel mobility of 110 cm²/Vs was successfully achieved using H₂ POA at 800°C for 30 min. H₂ POA reduces the interface trap density by about one order of magnitude compared with that without H₂ POA, resulting in considerable improvement of the inversion channel mobility to 3.5 times higher than that without H₂ POA. In addition, 4H-SiC MOSFET with H₂ POA has a lower threshold voltage of 3.1 V and a wide gate voltage operation range in which the inversion channel mobility is more than 100 cm²/Vs     

Fabrication of 4H-SiC n-channel IGBTs with ultra high blocking voltage

Owing to the conductivity modulation of silicon carbide (SiC) bipolar devices,n-channel insulated gate bipolar transistors (n-IGBTs) have a significant advantage over metal oxide semiconductor field effect transistors (MOSFETs) in ultra high voltage (UHV) applications.In this paper,backside grinding and laser annealing process were carried out to fabricate 4H-SiC n-IGBTs.The thickness of a drift layer was 120 μm,which was designed for a blocking voltage of 13 kV.The n-IGBTs carried a collector current density of 24 A/cm2 at a power dissipation of 300 W/cm2 when the gate voltage was 20 V,with a differential specific on-resistance of 140 mΩ·cm2.     

Self-aligned gate and source drain contacts in inverted-staggereda-Si:H thin-film transistors fabricated using selective area siliconPECVD

This article demonstrates full self-aligned inverted-staggered amorphous silicon thin-film transistors (TFT's) fabricated using selective plasma deposition of doped microcrystalline silicon source/drain contacts. Back-side exposure, using the bottom metal gate as the mask, produced the self-aligned contact openings. Selective deposition of the n+ silicon contact layer assures self-aligned ion resistance contacts and eliminates the need for reactive ion etching of the n+ silicon. Complete TFT fabrication requires no critical alignment steps. Transistors have linear mobility between 0.6 and 1.1 cm² /Vs, threshold voltage of 3.0 V, and sub-threshold slope of 0.35 V/decade. The OFF current is <10^-11 A with -10 V gate voltage and 10 V between the source and drain, and ON/OFF ratios exceed 10     

Schottky-barrier source/drain MOSFETs on ultrathin SOI body with a tungsten metallic midgap gate

This letter presents a simple low-temperature process to fabricate Schottky-barrier (SB) MOSFETs that integrates a midgap metallic gate (tungsten). The device architecture is based on a thin (10 nm) and lowly doped silicon-on-insulator film that provides a threshold voltage of -0.3 V independent on the depletion charge and therefore not sensitive to variations in film thickness and doping. A gate encapsulation technique using an SiO/sub 2/-like hydrogen silsesquioxane capping layer features 15-nm-wide spacers and ensures the compatibility with the PtSi self-aligned silicide process. Long-channel devices present an ideal subthreshold swing of 60 mV/dec, over six decades of I/sub on//I/sub off/ without any sign of sublinear upward bending of the I/sub DS/--V/sub DS/ curves at low drain voltage.