Crossover of Ba(Ti,Y)O3 Solid Solutions to Ba3Ti2YO8.5–BaTiO3 Composites and their Dielectric Properties

Ceramic samples with the nominal composition (1− x ) BaTiO₃+ x Ba₃Ti₂YO_8.5 ( x =0−0.535) were prepared by the mixed oxide method. X-ray diffraction (XRD) analysis shows that the materials are of single phase with a cubic symmetry as x ≤0.16. The compositions of the solid solutions ( x ≤0.16) can be expressed equivalently as Ba(Ti_{1− y} Y _y )O_3−δ ( y ≤0.122, y = x /(1+2 x )). For x >0.16, the materials are diphasic composites consisting of Ba(Ti_{1− y} Y _y )O₃ ( y =0.122) and Ba₃Ti₂YO_8.5. The microstructure observation by scanning electron microscopy supports the XRD result. The dielectric behavior and phase transitions of the solid solutions ( x ≤0.16) vary with different Y concentrations. The dielectric constant of the composites ( x >0.16) follows approximately the Lichteneker relation in a wide temperature range.     

Microwave Dielectric Properties of CaTiO3-CaAl1/2Nb1/2O3 Ceramics Doped with Li3NbO4

The microwave dielectric properties of CaTi_{1− x} (Al_1/2Nb_1/2) _x O₃ solid solutions (0.3 ≤ x ≤ 0.7) have been investigated. The sintered samples had perovskite structures similar to CaTiO₃. The substitution of Ti⁴⁺ by Al³⁺/Nb⁵⁺ improved the quality factor Q of the sintered specimens. A small addition of Li₃NbO₄ (about 1 wt%) was found to be very effective for lowering sintering temperature of ceramics from 1450–1500° to 1300°C. The composition with x = 0.5 sintered at 1300°C for 5 h revealed excellent dielectric properties, namely, a dielectric constant (ɛ_r) of 48, a Q × f value of 32 100 GHz, and a temperature coefficient of the resonant frequency (τ_f) of −2 ppm/K. Li₃NbO₄ as a sintering additive had no harmful influence on τ_f of ceramics.     

Weakly Coupled Relaxor Behavior of BaTiO3–BiScO3 Ceramics

The structural and dielectric properties of (1− x )BaTiO₃– x BiScO₃ ( x =0–0.5) ceramics were investigated to acquire a better understanding of the binary system, including determination of the symmetry of the phases, the associated dielectric properties, and the differences in the roles of Bi₂O₃ and BiScO₃ substitutions in a BaTiO₃ solid solution. The solubility limit for BiScO₃ into the BaTiO₃ perovskite structure was determined to be about x =0.4. A systematic structural change from the ferroelectric tetragonal phase to a pseudo-cubic one was observed at about x =0.05–0.075 at room temperature. Dielectric measurements revealed a gradual change from proper ferroelectric behavior in pure BaTiO₃ to highly diffusive and dispersive relaxor-like characteristics from 10 to 40 mol% BiScO₃. Several of the compositions showed high relative permittivities with low-temperature coefficients of capacitance over a wide range of temperature. Quantification of the relaxation behavior was obtained through the Vogel–Fulcher model, which yielded an activation energy of 0.2–0.3 eV. The attempt characteristic frequency was 10¹³ Hz and the freezing temperature, T _f, ranged from −177° to −93°C as a function of composition. The high coercive fields, low remanent polarization, and high activation energies suggest that in the BiScO₃–BaTiO₃ solid solutions, the polarization in nanopolar regions is weakly coupled from region to region, limiting the ability to obtain long-range dipole ordering in these relaxors under field-cooled conditions.     

Internal Oxidation of Ce3+-BaTiO3 Solid Solutions

The reoxidation process in highly Ce³⁺-doped BaTiO₃ ceramics was studied using TEM. Samples of two different types of solid solutions, Ba_1−XCe³⁺ _X Ti_1−X/4( V _Ti) X/4 O₃ and Ba_1−XCe³⁺ _X Ti⁴⁺_{1− X} Ti³⁺ _X O₃, were prepared by sintering oxide mixtures in air and in a reducing atmosphere, respectively. The solid solutions were reoxidized by annealing in air at high temperatures (1000°—1100°C). As a result of internal oxidation of Ce³⁺ and Ti³⁺, fluorite CeO₂ and monoclinic Ba₆Ti₁₇O₄₀ phases were precipitated in the perovskite matrix. In Ba_1−XCe³⁺ _X Ti_1−X/4( V _Ti)X/4O3 solid solution precipitates nucleate heterogeneously at grain boundaries and at extended defects inside the grains, whereas in Ba_1−XCe³⁺_XTi⁴⁺_1−XTi³⁺_XO₃ solid solution precipitates are nucleated mainly homogeneously inside reoxidized perovskite grains. The form of the precipitates and their orientational relationship with the matrix, as well as the mechanism of internal oxidation, are discussed.     

Preparation, Electrical Conductivity, and Thermal Expansion Behavior of Dense Nd1−xCaxCrO3 Solid Solutions

Nd_{1− x} Ca _x CrO₃ (0≤ x ≤0.25) solid solutions are synthesized using a two-step calcination solid-state reaction method and can potentially be used as interconnect applications in solid oxide fuel cells (SOFCs). The lattice parameters and unit cell volume decrease with an increase of the Ca²⁺ dopant concentration at the A-site. On the other hand, the relative density, electrical conductivity, and thermal expansion coefficient (TEC) increase with an increase of Ca²⁺ contents. Calcium doping significantly depresses the chromium vaporization of NdCrO₃, thus accelerating the sintering and densification of the oxides. Nd_{1− x} Ca _x CrO₃ with x =0.25 shows the best electrical conductivity of 28.8 and 1.1 S/cm at 850°C in air and hydrogen, respectively, with a high relative density of 98.0% and a good TEC of 9.19 × 10⁻⁶ K⁻¹ in the temperature range from 30° to 1000°C in air. This indicates that Nd_0.75Ca_0.25CrO₃ is a promising candidate as an interconnect material for application in SOFCs.     

Polymorphism and Dielectric Properties of Nb-Doped BaTiO3

A working subsolidus phase diagram for the system BaTiO₃–Ba₅Nb₄O₁₅ has been determined by firing sol–gel-synthesized samples over a range of temperatures. The main difference from previous diagrams is the greater extent of the Nb-doped BaTiO₃ cubic solid solutions, BaTi_{1−5 x} Nb_{4 x} O₃, at lower temperatures with x extending to 0.09 at 900°C, but only 0.05 at 1400°C. Electrical property measurements show that compositions with large x ( x ≥0.0025) are highly insulating for pellets sintered at 1300°C in air, followed by a slow cool. Compositions with low x , however, exhibit a residual semiconducting grain core and are not fully reoxidized readily. Composition dependence of the dielectric properties shows a continuous and smooth transition from classic ferroelectric behavior with pure BaTiO₃ to normal dielectric response with a temperature-independent relative permittivity of approximately 22–24 for x >∼0.08. At intermediate compositions, ranges of both relaxor ferroelectric and quasi-ferroelectric behavior are observed. Possible reasons for an observed anomalous increase in value of the permittivity at the ferroelectric transition temperature at low x , which is superposed on an overall decrease in permittivity with increasing x , are discussed.     

Pyrochlore Phase Formation in the System Bi2O3–ZnO–Ta2O5

The subsolidus phase diagram of the system Bi₂O₃–ZnO–Ta₂O₅ in the region of the cubic pyrochlore phase has been determined at 1050°C. This phase forms a solid solution area that includes the ideal composition P, Bi₃Zn₂Ta₃O₁₄; possible solid solution mechanisms are proposed, supported by density measurements of Zn-deficient solid solutions. The general formula of the solid solutions is Bi_{3+ y} Zn_{2− x} Ta_{3− y} O_{14− x − y} , based on the creation of Zn²⁺, O²⁻ vacancies in Zn-deficient compositions and a variable Bi/Ta ratio.     

Effect of V2O5 Doping on the Sintering and Dielectric Properties of M-Phase Li1+x−yNb1−x−3yTix+4yO3 Ceramics

The effect of the addition of V₂O₅ on the structure, sintering and dielectric properties of M -phase (Li_{1+ x − y} Nb_{1− x −3 y} Ti _x +4 _y )O₃ ceramics has been investigated. Homogeneous substitution of V⁵⁺ for Nb⁵⁺ was obtained in LiNb_{0.6(1− x )}V_{0.6 x} Ti_0.5O₃ for x ≤ 0.02. The addition of V₂O₅ led to a large reduction in the sintering temperature and samples with x = 0.02 could be fully densified at 900°C. The substitution of vanadia had a relatively minor adverse effect on the microwave dielectric properties of the M -phase system and the x = 0.02 ceramics had [alt epsilon]_r= 66, Q × f = 3800 at 5.6 GHz, and τ_f= 11 ppm/°C. Preliminary investigations suggest that silver metallization does not diffuse into the V₂O₅-doped M -phase ceramics at 900°C, making these materials potential candidates for low-temperature cofired ceramic (LTCC) applications.     

Solid Solubility of Holmium, Yttrium, and Dysprosium in BaTiO3

The solid solubility of R ions (R = Ho³⁺, Dy³⁺, and Y³⁺) in the BaTiO₃ perovskite structure was studied by quantitative electron-probe microanalysis (EPMA) using wavelength-dispersive spectroscopy (WDS), scanning electron microscopy (SEM), and X-ray diffractometry (XRD). Highly doped BaTiO₃ samples were prepared using mixed-oxide technology including equilibration at 1400° and 1500°C in ambient air. The solubility was found to depend mainly on the starting composition. In the TiO₂-rich samples a relatively low concentration of R incorporated preferentially at the Ba²⁺ lattice sites (solubility limit ∼Ba_0.986R_0.014Ti_0.9965(V^"_Ti^")_0.0035O₃at 1400°C). In BaO-rich samples a high concentration of R entered the BaTiO₃ structure at the Ti⁴⁺ lattice sites (solubility limit ∼BaTi_0.85R_0.15O_2.925(V_O^••)_0.075at 1500°C). Ho³⁺, Dy³⁺, and Y³⁺incorporated preferentially at the Ti⁴⁺ lattice sites stabilize the hexagonal polymorph of BaTiO₃. The phase equilibria of the Ho³⁺–BaTiO₃ solid solutions were presented in a BaO–Ho₂O₃–TiO₂phase diagram.     

Ordered Structure and Dielectric Properties of Lanthanum-Substituted Ba(Mg1/3Ta2/3)O3

Both 1:2 and 1:1 ordered structures form in the perovskite solid solutions of La-substituted BMT Ba_{1− x} La _x (Mg_{(1+ x )/3}Ta_{(2− x )/3})O₃, sintered at 1600°C. The 1:2 ordered structure exists in the composition range 0.0 ≤ x ≤ 0.12, while that of 1:1 ordered structure exists in a wider composition range 0.04 ≤ x ≤ 1.0. Two ordered phases coexist in 0.04 ≤ x ≤ 0.12. High-resolution micrographs indicate that 1:2 and 1:1 ordered domains coexist in one grain. The ordering parameter of 1:2 phase decreases with x , yet that of 1:1 phase increases with x . Both increase with soak time. Variations in ordering are discussed in terms of cation occupancy and crystal chemistry. The quality factor increases with x , reaches a maximum, then decreases with x . The dielectric constant increases with x first, and levels off.     

Stabilization of Ordered Zirconium Titanates through the Chemical Substitution of Ti4+by Al3+/Ta5+

We have investigated the ZrO₂–AITaO₄ system to understand how selected chemical substitutions can be used to control cation-ordering transformations in zirconium titanate based dielectric ceramics. The complete replacement of the Ti content of Zr _x Ti_2–xO₄ by a coupled Al³⁺/Ta⁵⁺ substitution permits the synthesis of a wide range of isostructural Zr _x (Al_0.5Ta_0.5)_2–xO₄ solid solutions. At high temperatures a disordered α-PbO₂ type of structure is formed for 0.375 ≤ x ≤ 1.03. Samples with 0.67 ≤ x ≤ 1.03 undergo a cation-ordering reaction to a structure in which the a and b axes of the parent disordered Cell are doubled. The stabilities of these cation-ordered derivative structures are significantly greater than those of the ordered zirconium titanates. The ordering temperatures are composition dependent with a maximum of 1393°C occurring for Zr_0.86(Al_0.5TaO_0.5)_1.14O₄. The higher transition temperatures also enhance the kinetics of the ordering transition; whereas the pure zirconium titanates require extended annealing to produce complete cation order, fully ordered Zr_χ(Al_0.5Ta_0.5)_2–χO₄ solid solutions are produced during a normal furnace cool.     

Structure and Dielectric Properties of Pb(Sc2/3W1/3)O3–Pb(Zr/Ti)O3 Relaxors

The structure and dielectric properties of (1− x )Pb(Sc_2/3W_1/3)O₃–( x )Pb(Zr/Ti)O₃ ceramics have been investigated over a full substitution range. All compositions with x < 0.5 adopt a cubic perovskite structure; however, for x ≤ 0.25 a doubled cell results from a 1:1 ordered distribution of the B-site cations. The structural order in Pb(Sc_2/3W_1/3)O₃ (PSW) can be described by a random-site model with one cation site occupied by Sc³⁺ and the other by a random distribution of (Sc_1/3³⁺W_2/3⁶⁺). The ordering is destabilized in solid solutions of PSW with PbZrO₃ (PSW–PZ), but stabilized by PbTiO₃ in the (1− x )PSW–( x )PT system. The changes in order are accompanied by alterations in the dielectric response of the two systems. For PSW–PZ the temperature of the permittivity maximum ( T _ɛ,max) increases linearly with x ; however, for PSW–PT T _ɛ,max decreases in the ordered region (up to x = 0.25) and then increases rapidly as the order is lost. Similar effects were produced by modifying the degree of order of (0.75)PSW–(0.25)PT; when the order parameter was reduced from ∼1.0 to ∼0.65, T _ɛ,max increased by more than 60°C.     

X-ray Diffraction and 151Eu Mössbauer Spectroscopic Study of the Hf1−xEuxO2−x/2(0 ≤x≤ 1.0) System

Powder X-ray diffractometry (XRD) and ¹⁵¹Eu Mössbauer spectroscopy were performed for samples prepared in the temperature range 1500–1500°C for the hafnia–europia (HfO₂–Eu₂O₃) system Eu _x Hf_{1− x} O_{2− x /2}(0 ≤ x ≤ 1.0). The XRD results showed that two types of solid solution phases formed in the composition range 0.25 ≤ x ≤ 0.725: an ordered pyrochlore-type phase in the middle-composition range (0.45 < x < 0.575) and a disordered fluorite-type phase, enveloping the pyrochlore-type phase on both sides, in the composition ranges 0.25 ≤ x ≤ 0.40 and 0.60 ≤ x ≤ 0.725. ¹⁵¹Eu Mössbauer spectroscopy sensitively probes local environmental changes around trivalent europium (Eu³⁺) caused by the formation of these solid solution phases. In addition to the broad, single Mössbauer spectra observed in this study for the Eu³⁺, the values of isomer shift (IS) exhibited a pronounced minimum in the neighborhood of the stoichiometric pyrochlore phase ( x ≈ 0.5). Such IS behavior of Eu³⁺ was interpreted based on the XRD crystallographic information that the ordered pyrochlore phase has a longer (in fact, the longest) average Eu–O bond length than those of the disordered fluorite phases on both sides or the monoclinic (and C-type) Eu₂O₃at x = 1.0.     

Microstructure and Photoluminescence Properties of Mg-Doped BaTiO3:Pr3+ Phosphor

The photoluminescence of Mg-doped BaTiO₃:Pr³⁺ (Pr³⁺: 0.1 mol%) ceramics was investigated by changing the doping concentration of Mg and the sintering temperature. The results indicated that the intensity of red emission due to the ¹ D ₂→³ H ₄ transition of Pr³⁺ exhibited significant dependence on both the Mg doping content and the sintering temperature; the strongest red emission intensity was observed for 2.0 mol% Mg-doped ceramics sintered at 1050°C. An interpretation of the results obtained was made in terms of the changes in the crystal structure and microstructure of the ceramics.     

Phase Transitions in the System BaTiO3—KnbO3

Solid solution formation in the system BaTiO₃—KnbO₃ was established by X-ray diffraction and dielectric measurements. Solid solutions with cubic symmetry were observed in the composition range from 4 to 90 mole % KnbO₃ at room temperature. The lattice parameter for the BaTiO₃ solid solutions increased with increasing KNbO₃; that for the KnbO₃ solid solutions decreased with the addition of BaTiO₃. A distinct discontinuity in lattice parameter was observed at the composition containing about 65 mole % BaTiO₃. Dielectric measurements were made from-195° to 400°C. The cubic-tetragonal transition temperature of BaTiO₃ was rapidly lowered with increasing addition of KNbO₃, whereas the two lower phase transition temperatures were raised. All three phase transitions of KnbO₃ were rapidly lowered with increasing addition of BaTiO₃. The observed phase transitions, lattice parameters, and electron probe data suggest a complex region in the subsolidus which extends from 35 to about 75 mole % KNbO₃.     

Ferroelectric and Piezoelectric Properties of Na1−xBaxNb1−xTixO3 Ceramics

Piezoelectric ceramics Na_{1− x} Ba _x Nb_{1− x} Ti _x O₃ with low BaTiO₃ concentrations x have been prepared by the solid-state reaction method, and their ferroelectric and piezoelectric properties have been studied. The ceramics are classic ferroelectrics when x ≤0.10, and the ferroelectric–paraelectric phase transition becomes diffusive when x ≥0.15. A low doping level of BaTiO₃ changes the NaNbO₃ ceramics from antiferroelectric to ferroelectric. With the increase in BaTiO₃ doping level, the Curie temperature of ceramics decreases linearly and the remnant polarization and coercive field also decrease, while their dielectric constant increases. Na_0.9Ba_0.1Nb_0.9Ti_0.1O₃ ceramics show the largest piezoelectric constant d ₃₃ (147 pC/N) and good sinterability, suggesting that it is a good candidate for lead-free piezoelectric ceramics.     

Microstructural Changes during the Reduction/Reoxidation Process in Donor-Doped BaTiO3 Ceramics

Microstructural changes occurring during oxidation of the reduced form of donor-doped BaTiO₃ (Ba_{1− X} D _X ^.Ti_{1− X} ⁴⁺Ti _X ³⁺O₃) and during reduction of the oxidized form of donor-doped BaTiO₃ (Ba_{1− X} D _X ^.Ti_{1− X /4}⁴⁺( V _Ti^) _{X /4}O₃) were studied using TEM. Samples of both types of solid solutions, containing different La concentrations (from 2 to 20 mol% La), were prepared by sintering under reducing conditions and in air, respectively. The reduced form of donor-doped BaTiO₃ was oxidized by annealing at high temperatures (1150° and 1350°C) in air, while the oxidized form was reduced by annealing under reducing conditions. Because of oxidation of the reduced phase of donor-doped BaTiO₃, the Ti-rich phases Ba₆Ti₁₇O₄₀ and BaLa₂Ti₄O₁₂ were precipitated. Reduction of the oxidized form caused precipitation of the Ba-rich phase Ba₂TiO₄ preferentially inside the matrix grains. All precipitates had well-defined orientational relationships with the perovskite matrix.     

Subsolidus Phase Relations in the Ga2O3-In2O3-SnO2 System

Subsolidus phase relationships in the Ga₂O₃–In₂O₃–SnO₂ system were studied by X-ray diffraction over the temperature range 1250–1400°C. At 1250°C, several phases are stable in the ternary system, including Ga₂O₃( ss ), In₂O₃( ss ), SnO₂, Ga_{3− x} In_{5+ x} Sn₂O₁₆, and several intergrowth phases that can be expressed as Ga_{4−4 x} In_{4 x} Sn _{n −4}O_{2 n −2} where n is an integer. An In₂O₃–SnO₂ phase and Ga₄SnO₈ form at 1375°C but are not stable at 1250°C. GaInO₃ did not form over the temperature range 1000–1400°C.     

Chemical Diffusivity of BaTiO3−δ: IV, Acceptor-Doped Case

The chemical diffusivity of 1.8 mol% aluminum-doped BaTiO_3−δ was measured on single-crystal specimens, as a function of ambient oxygen partial pressure, in the range 10⁻¹⁸ atm ≤ P _O2≤ 1 atm and at temperatures of 800°≤ T ≤ 1100°C, via a conductivity-relaxation technique. As in the polycrystalline, undoped BaTiO_3−δ described in Part II of this work, the chemical diffusivity exhibited a maximum, of thermodynamic origin, approximately at the stoichiometric composition (δ= 0). The measured diffusivity was analyzed, based on the defect structure proposed and Wagner's classic theory of chemical diffusion, and the mobilities of the electrons and holes, as well as all of the relevant defect-equilibrium constants, then were evaluated with no prior assumptions. The evaluated parameters were compared with those for the undoped BaTiO_3−δ.     

High-Temperature Dielectrics in the BiScO3–BaTiO3–(K1/2Bi1/2)TiO3 Ternary System

Perovskite solid solution in the (1− x )[0.4BiScO₃–0.6BaTiO₃]+ x (K_1/2Bi_1/2)TiO₃ [BSBT–KBT x ] system was synthesized using conventional sintering and hot-isostatic pressing. Dielectric properties of BSBT ceramics with different dopant levels of KBT were characterized as a function of temperature and frequency for potential use of high-temperature capacitors. The BSBT ceramics with KBT exhibited high dielectric permittivities (ɛ_r) (>1700 at RT) and low dielectric loss over the temperature range from 100° to 300°C, with flat temperature coefficients of permittivity (TCɛs). In addition, BSBT ceramics with increasing KBT were observed to possess dielectric relaxation characteristics at temperatures (>RT) as observed in lead-based relaxors. Furthermore, high energy densities, being on the order of 4.0 J/cm³ at 220 kV/cm was observed for the BSBT–KBT20 ceramics from the electric-field polarization behavior.