沉淀法合成纳米CeO2的晶粒生长动力学

以Ce(NO3)3·6HzO为铈源,(NH4)2CO3·H2O为沉淀剂,并加入一定量表面活性剂PEG4000,采用液相沉淀法制备前驱体Ce2(CO3)3·H2O,前驱体经热处理合成纳米CeO2.根据XRD线宽法研究了纳米CeO2热处理过程的晶粒生长动力学,结果表明随焙烧温度升高,CeO2晶粒尺寸显著增大;300℃下焙烧时间对CeO2晶粒尺寸影响不明显,700℃下CeO2晶粒随焙烧时间延长而长大,且焙烧初期粒径增长较快,超过180 min后增长速率变慢;700℃时CeO2晶粒生长指数为5,即符合5次方动力学方程,晶粒生长速率常数为1.986 5×104 nm5/min;由于纳米尺寸效应,使得CeO2晶粒生长活化能在低温区和高温区不同,低于400℃时为25.64 kJ/mol,高于400℃时为87.64 kJ/mol;认为热处理过程CeO2的晶粒生长为扩散生长机制.     

声化学法制备Y2BaCuO5纳米晶及其机理研究

以Y2O3，CuCl2和BaCl2等为起始原料，采用声化学方法制备了Y2BaCuOs纳米晶。研究了超声波功率对合成纳米Y2BaCuO5的结晶性能及合成活化能的影响。结果表明：在湿化学过程中施加超声辐射能明显降低合成YzBaCuO5的晶粒尺寸和合成活化能；超声功率从100w增加到300W，合成的纳米Y2BaCu05晶粒尺寸从50nm～60nm减小到20nm～30nm，其合成活化能由87．1kJ／mol降低到53．1kJ／mol。     

表面机械研磨处理制备纳米晶Ni的晶粒生长动力学

利用表面机械研磨处理(SMAT)技术在纯Ni上制备一定厚度的纳米晶表层,利用X射线衍射(XRD)和透射电镜(TEM)研究了纳米晶Ni的晶粒生长动力学,计算了描述晶粒生长动力学的时间指数n和晶粒生长激活能Q.研究表明,纳米晶Ni在423～723 K退火时的时间指数n约为0.14.当纳米晶Ni在423 ～523 K退火时,其晶粒生长激活能Q为32.1 kJ/mol,表明在这一温度区间内晶粒生长由晶界和亚晶界的微结构重新排列所控制;当纳米晶Ni在523～723 K退火时,晶粒生长激活能Q为121.3 kJ/mol,表明在这一温度区间内晶粒生长由晶界扩散所控制.TEM观察表明纳米晶Ni在较高温度下退火时出现异常的晶粒长大现象.     

金属纳米晶粉体材料中的不连续晶粒长大

采用高能球磨法制备了Co纳米晶粉体,平均晶粒尺寸为(17±3)nm.设计了一系列宽温度范围的退火实验,考察纯Co纳米晶粉体的晶粒长大行为.实验发现,低温区和高温区的晶粒长大动力学有明显差异,而在中温区出现不连续晶粒长大特征.高分辨透射电镜观测表明:在低温区,纳米晶中存在较大比例的小角度纳米晶界,而在高温区则基本为典型的大角度晶界.结合纳米晶热力学计算和DSC分析,认为纳米晶粒在中温区的突发迅速长大是由残余储存能作为附加驱动力激发的动力学过程,其主导机制是通过相邻小角度位向差的纳米晶粒的转动而实现晶粒快速粗化.     

ZnO掺杂纳米CeO2的共沸蒸馏法合成

采用化学共沉淀法结合正丁醇共沸蒸馏处理前驱体合成了ZnO掺杂纳米CeO2颗粒,通过XRD,DSC/TG,IR,TEM,原子吸收光谱以及紫外透过率分析等方法对其结构和性能进行了表征;并根据XRD线宽法,由Scherrer公式计算其晶粒尺寸,研究了共沸蒸馏、ZnO掺杂、以及焙烧温度和时间对CeO2纳米晶粒尺寸的影响.结果表明:正丁醇共沸蒸馏法能有效脱除前驱体凝胶中的水分,防止干燥和焙烧过程中硬团聚的形成,从而得到粒径更小、分布更均匀、分散性更好的纳米CeO2颗粒;2 mol%～10 mol%掺杂ZnO能与纳米CeO2形成固溶体,且掺入量增加引起纳米CeO2晶粒有所增大;随焙烧温度提高,ZnO掺杂纳米CeO2晶粒显著长大,而高温下随焙烧时间延长,其晶格进一步趋于完整,晶粒尺寸增加;纳米CeO2具有良好的可见光透过和紫外光吸收能力,ZnO掺杂不会影响纳米CeO2的紫外遮蔽效果.     

ZnO掺杂纳米CeO2的共沸蒸馏法合成

采用化学共沉淀法结合正丁醇共沸蒸馏处理前驱体合成了ZnO掺杂纳米CeO2颗粒,通过XRD,DSC/TG,IR,TEM,原子吸收光谱以及紫外透过率分析等方法对其结构和性能进行了表征;并根据XRD线宽法,由Scherrer公式计算其晶粒尺寸,研究了共沸蒸馏、ZnO掺杂、以及焙烧温度和时间对CeO2纳米晶粒尺寸的影响.结果表明正丁醇共沸蒸馏法能有效脱除前驱体凝胶中的水分,防止干燥和焙烧过程中硬团聚的形成,从而得到粒径更小、分布更均匀、分散性更好的纳米CeO2颗粒;2 mol%～10 mol%掺杂ZnO能与纳米CeO2形成固溶体,且掺入量增加引起纳米CeO2晶粒有所增大;随焙烧温度提高,ZnO掺杂纳米CeO2晶粒显著长大,而高温下随焙烧时间延长,其晶格进一步趋于完整,晶粒尺寸增加;纳米CeO2具有良好的可见光透过和紫外光吸收能力,ZnO掺杂不会影响纳米CeO2的紫外遮蔽效果.     

水热沉淀法合成SnO_2纳米晶

用水热沉淀法合成了不同粒径的 Sn O2 纳米晶 ,属于四方晶系 ,空间群为 P4/ mnm。计算表明 :随焙烧温度的升高 ,Sn O2 晶粒度增大 ;而平均晶格畸变率则随晶粒度的增大而减小 ,表明粒子越小晶格畸变越大 ,晶粒发育越不完整。TEM分析结果表明 :所合成的 Sn O2 纳米粒子基本呈球形 ;随焙烧温度的升高 ,Sn O2 粒子的粒径增大。热失重分析表明 :水热沉淀法所合成的 Sn O2 纳米粉末中杂质含量很少 ,纯度高。     

电沉积纳米晶Ni-Co-Fe合金镀层的热稳定性

用脉冲电沉积方法制备表面平整光亮的纳米晶Ni-Co-Fe合金镀层.采用XRD、TEM、EDS、DSC和显微硬度计分别研究纳米晶Ni-Co-Fe合金镀层的微观结构、化学成分、热稳定性及其硬度.结果表明:纳米晶Ni-Co-Fe合金镀层的晶体结构为单相的面心立方结构,其晶粒尺寸随镀层Co含量的增加而减小;合金镀层的显微硬度随退火温度的升高而提高,在300～375℃时达最大值,存在明显的退火再强化,之后,随着退火温度的继续升高明显下降;当镀层在低于375℃退火时,晶粒长大速度较慢;而当镀层在高于450℃退火时,晶粒迅速长大,并呈现较强的(111)织构.升温速率为20℃/min时,纳米晶Ni-Co-Fe合金镀层的DSC结果显示,晶粒长大的峰值温度随镀层Co含量的增加而升高.由Kissinger方程求得纳米晶Ni-Co-Fe合金的晶粒长大激活能随镀层Co含量的增加而增大.     

溶胶-喷雾干燥超细/纳米晶W-20Cu复合粉末的烧结行为

采用喷雾干燥-氢气还原法制备超细/纳米晶W-20Cu(质量分数,%)复合粉末,粉末压坯直接从室温推入高温区烧结不同时间后直接取出水淬,研究其烧结致密化和显微组织的变化。结果表明,超细/纳米晶W-20Cu粉末在1000～1200℃烧结时发生迅速致密化。粉末压坯在1200℃烧结60min,其材料致密度已达到96.4%。1420℃烧结90min时致密度达到99%以上。1100～1420℃烧结时其烧结致密化活化能不断减小,从1100℃时的276.3kJ/mol减小到1420℃时的29.1kJ/mol。当温度低于1200℃时,W晶粒长大不明显,当温度超过1300℃时,W晶粒开始有明显长大。随温度的升高W晶粒发生显著球形化,1420℃烧结时发现其晶粒长大符合G3=kt的Ostwald机制,此时晶粒长大动力学系数K仅为0.024μm3/min。     

纳米晶SmCo7合金的相稳定性、相变行为及其对磁性能的影响

以纳米晶单相SmCo7合金块体为初始原料,通过系列退火系统研究了随着晶粒长大其物相组成和显微组织的演变特征。研究发现纳米晶SmCo7相从室温至600℃都能保持很好的相稳定性(晶粒长大十分缓慢)。而且研究发现纳米晶SmCo7相的失稳分解和晶粒的突发长大会同时发生。值得注意的是分解形成的Sm2Co17相大部分是以显微孪晶的形式存在,而SmCo5相则是呈圆形均匀分布于合金中。另外通过对具有不同晶粒尺寸和物相组成的纳米晶SmCo7合金的室温磁性能细致表征,发现单相SmCo7合金都具有非常优异的磁性能。而其中平均晶粒尺寸为33nm的单相SmCo7合金具有最高矫顽力,达到1164.54kA/m;平均晶粒尺寸为29nm的单相SmCo7合金具有最高的磁能积,达到95.65kJ/m3。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

The Mirror with Patterns of Auspicious Animals and Grapes——Exquisite cast mirror and the technology of surface tin-enrichment by rubbing-in and infiltration of tin-rich powder

<正>Bronze mirrors were used by the Chinese people before the introduction of the glass mirror.Only after it was replaced by the glass mirror did the bronze mirror gradually retreat from people's lives.Different styles of bronze mirrors were made in different historical periods,particularly in the Warring States Period,the Han and Tang Dynasties,which were the three peaks of the development of bronze mirror arts in ancient China.The casting techniques were exquisite.The surface of the bronze mirror was smooth and bright enough to reflect one's image,and there were scarcely any casting defects on the mirror surface.On the back of the bronze mirror,there were rich depictions of Arts and Humanities,and the ornamentations were also     

The 9th China International Diecasting Congress & Exhibition

The 9th China International Diecasting Congress ＆ Exhibition was held on July 22-24, 2014 at Shanghai New International Expc Centre. This exhibition was the most successful over the years, with over 6890 visitors and 155 exhibitors, and the exhibition area increased by 30% from 9,500 square meters in 2012 to 12340 square meters. Die casting enterprises from a total of 24 countries and regions, including China mainland, Chinese Taiwan and Hong Kong, South Korea, Japan, Germany, India, Thailand, Malaysia, the United States, Russia, Australia, Iran, Ukraine, Brazil, Colombia, Singapore, Austria, Canada, Croatia, France, Turkey, United Kingdom, Vietnam, attended the congress and exhibition.     

Introduction of the Fluid Control Engineering Institute of Kunming University of Science and Technology

正The Fluid Control Engineering Institute of Kunming University of Science and Technology was set up in 1996.The researches of institute concentrate on electro-hydraulic(pneumatic)servo/proportional control and hydromechatronics.The Institute is committed to research and development of electro-hydraulic control of high-end technical equipment in ferrous metallurgy refining produc-     

RARE METALS Volume Contents

正~~     

Antimony Induced Crystallization of Amorphous Silicon

Antimony induced crystallization of PVD (physics vapor deposition) amorphous silicon can be observed on sapphire substrates. Very large crystalline regions up to several tens of micrometers can be formed. The Si diffraction patterns of the area of crystallization can be observed with TEM (transmission electron microscopy). Only a few and much smaller crystals of the order of 1μm were formed when the antimony layer was deposited by MBE (molecular beam epitaxy) compared with a layer formed by thermal evaporation. The use of high vacuum is essential in order to observe any Sb induced crystallization at all. In addition it is necessary to take measures to limit the evaporation of the antimony.     

A CUMULATIVE FATIGUE DAMAGE RULE UNDER THE ALTERNATIVE OF CORROSION OR CYCLIC LOADING

Fatigue damage increases with the applied loading cycles in a cumulative manner and the material deteriorates with the corrosion time. A cumulative fatigue damage rule under the alternative of corrosion or cyclic loading was proposed. The specimens of aluminum alloy LY12-CZ soaked in corrosive liquid for different times were tested under the constant amplitude cyclic loading to obtain S-N curves. The test was carried out to verify the proposed cumulative fatigue damage rule under the different combinations among corrosion time, loading level, and the cycle numbers. It was shown that the predicted residual fatigue lives showed a good agreement with the experimental results and the proposed rule was simple and can be easily adopted.