油嘴喷射锥角对柴油可控预混压燃燃烧特性的影响

进行了在柴油可控预混压燃燃烧模式下,油嘴喷射锥角对燃烧与排放的影响研究.实验结果表明,采用155°和125°喷射锥角的油嘴,改变多脉冲喷射定时可控制预混燃烧放热幅度,影响NOx与HC和CO排放的折衷关系.在3次和6次多脉冲喷射条件下,采用125°油嘴能获得更低的NOx和HC排放.特别是采用6次脉冲喷射模式,即使在较早的喷射定时(130°CA BTDC)下,仍能保证较低的HC和CO排放.研究表明,通过减小油嘴喷射锥角、增加脉冲喷射次数和大幅度提前喷射定时,能够在获得低NOx排放的可控预混燃烧过程的同时,保证HC和CO排放只有小幅增加.     

喷射参数对二甲醚PPCCI发动机燃烧与排放特性的影响

在一台6缸增压电控共轨二甲醚发动机上进行试验,研究了预喷时刻、预喷燃料量、喷射压力、主喷时刻等喷射参数对二甲醚部分预混合充量压缩燃烧(PPCCI)发动机燃烧与排放特性的影响。试验结果表明:随预喷时刻提前,缸内压力峰值降低,二甲醚发动机缸内燃烧由两阶段放热转变为PPCCI三阶段放热,氮氧化物(NOx)排放显著降低,HC和CO排放升高;随预喷射燃料量增加,缸内压力峰值及预混合燃烧的冷焰反应和热焰反应速率明显增大,NOx排放逐渐降低,HC和CO排放显著升高;随喷射压力降低,预混合燃烧热焰反应速率增加,主喷扩散燃烧始点推迟,扩散燃烧放热率峰值和NOx排放明显降低,HC和CO排放升高;随主喷时刻推迟,预喷预混合燃烧几乎没有变化,主喷扩散燃烧延后,缸内压力峰值和放热率峰值降低,NOx排放显著降低,HC和CO排放升高。     

不同点火时刻下天然气掺氢缸内直喷发动机燃烧与排放特性

在缸内直喷火花点火发动机上开展了天然气掺混0％-18％氢气的混合燃料不同点火时刻下的试验研究。结果表明：对于给定的喷射时刻和喷射持续期,点火时刻对发动机性能、燃烧和排放有较大影响,喷射结束时刻与点火时刻的间隔对直喷天然气发动机极为重要,喷射结束时刻与点火时刻的间隔缩短时,混合气分层程度高,燃烧速率快,热效率高。最大放热率等燃烧特征参数随点火时刻的提前而增加。HC排放随点火时刻的提前而下降,CO2和NOx排放随点火时刻的提前而增加,NOx排放的增加在大点火提前角下更明显。掺氢可降低HC排放,对CO和CO2排放影响不大。掺氢量大于10％时可提高天然气发动机热效率。     

柴油机多脉冲喷射预混燃烧过程多维数值模拟

建立了三维CFD耦合化学反应动力学模型,对柴油机缸内多脉冲喷射形成的预混燃烧过程进行了模拟,结果表明:该模型能够较准确地预测缸压曲线、着火时刻、NOx和CO2排放,能够预测着火位置、燃烧中间产物和有害排放物的生成历程.多脉冲喷射预混燃烧产生的NOx、CO和未燃HC排放主要来源于靠近缸壁余隙内,要提高这种燃烧方式的效率和降低排放,关键是要减少燃油附壁.     

基于多脉冲喷射、可变增压以及推迟进气门关闭定时技术的混合燃烧控制策略

针对重载柴油机实现高效清洁燃烧进行了燃烧控制策略的研究.实验在一台拥有高压共轨系统、废气再循环系统、可变增压系统以及推迟进气门关闭定时系统的单缸实验发动机上进行.实验结果表明,当平均指示压力低于1.1 MPa时可以采用高EGR率的低温燃烧策略.其中,基于不同负荷工况高效清洁燃烧,需要配合进气增压、推迟进气门关闭定时技术以及不同的喷油模式.在低负荷工况下,单次早喷模式及高EGR率可以实现高的热效率以及低的NOx与碳烟排放.在中负荷工况下,采用多脉冲喷射模式及高EGR率协同作用,在降低化学反应速率的同时增强了混合,避免了因为局部不均匀而导致的碳烟排放过高.高的增压度提高了缸内充量密度,有效降低了NOx、碳烟、CO及HC排放,提高了热效率.研究结果还显示,在推迟进气门关闭定时系统的帮助下,采用多脉冲喷射以及高的增压压力,可以在保持高的热效率的同时进一步降低NOx以及碳烟排放.     

电喷柴油机优化燃烧和排放的数值模拟

应用三维CFD模拟软件FIRE,对1台6106柴油机在不同预喷油量,主预喷定时和主预喷间隔的条件下的喷雾与燃烧过程进行了数值模拟。通过分析缸内压力和温度变化以及燃烧产物的质量分数,研究了预喷射参数对燃烧过程及NOx和碳烟的影响。结果表明:采用不同预喷射策略,可有效降低缸内燃烧压力,优化柴油机的排放。随着预喷油量的增加,NOx变化不大,烟度(Soot)逐渐增加;随着预喷定时的提前,Soot生成量变化不大,NOx排放逐渐增加。     

基于调制多脉冲喷油模式的柴油预混合燃烧和排放特性的研究

在MULINBUMP-HCCI燃烧系统基础上,通过柔性调制多脉冲喷射的脉冲脉宽和间隔,形成了不同的喷油模式,以研究调制的多脉冲喷油模式对早喷HCCI燃烧和排放的影响。试验结果表明,改变多脉冲喷油模式,可以提高HCCI热效率,获得更高的输出功率,同时保持低的NOx和碳烟排放。5次和6次多脉冲喷射,递增式喷油方式具有很大的优势;对比不同次数的多脉冲喷射发现,增加多脉冲喷射次数可以扩大HCCI的负荷范围、提高指示热效率和降低CO排放。在110°CABTDC喷油定时,6次多脉冲喷射递增喷油方式6PIM相对于5次多脉冲喷射5PIM喷油方式的pIMEP和指示热效率分别提高了27.6%和13%,而CO排放减少了230%。     

高速直喷柴油机的燃烧特性和排放试验研究

本文对一台四缸高速直喷柴油机的燃烧和排放特性进行了试验研究,分析研究了负荷及燃油喷射压力和供油提前角对该柴油机的着火延迟、瞬时放热率、NOx、CO及HC排放的影响。结果显示随着负荷及燃油喷射压力的提高着火延迟缩短、NOx排放增加;随着供油提前角的推迟NOx排放显著减少;而CO和HC的排放量与负荷及供油提前角的关系不大。     

CO_2进气道和缸内喷射对柴油准HCCI燃烧的影响

通过开发的气体喷射系统,研究并对比了进气道和缸内喷射CO2对准均质压燃燃烧排放的影响.准HCCI燃烧由两段喷油实现.结果表明:随着缸内和进气道CO2循环喷射量的增大,缸内最高平均温度降低,燃烧相位推迟,最大压力升高率变化不大;NOX排放减小,HC和CO排放增大.等CO2喷射量下,NOx随着缸内CO2喷射始点的提前而减小;缸内喷射的HC和CO排放较进气道喷射的大.随着CO2循环喷射量的增大,进气道喷射的烟度开始变化不大,然后急剧上升;而缸内喷射的烟度变化不大.     

MULINBUMP-HCCI复合燃烧放热特征及其对排放和热效率的影响

提出了基于多脉冲喷射和BUMP燃烧室的MULINBUMP HCCI复合燃烧技术。发动机试验和CFD数值模拟研究表明,多脉冲喷射参数,特别是多脉冲喷射定时可以控制预混合气的形成,从而控制燃烧放热率。具有分布式放热率的工作过程的热效率与直喷式柴油机相当,但同时改善了NOx和碳烟排放。在不采用废气再循环的条件下,NOx排放在较低负荷时只有11×10-6,高负荷时也不超过250×10-6。碳烟排放始终小于0 5BSU。     

Ash-forming elements in four Scandinavian wood species. Part 1: Summer harvest

Woody biomass in Finland and Sweden comprises mainly four wood species: spruce, pine, birch and aspen. To study the ash, which may cause problems for the combustion device, one tree of each species were cut down and prepared for comparisons with fuel samples. Well-defined samples of wood, bark and foliage were analyzed on 11 ash-forming elements: Si, Al, Fe, Ca, Mg, Mn, Na, K, P, S and Cl. The ash content in the wood tissues (0.2–0.7%) was low compared to the ash content in the bark tissues (1.9–6.4%) and the foliage (2.4–7.7%). The woods’ content of ash-forming elements was consequently low; the highest contents were of Ca (410–1340 ppm) and K (200–1310), followed by Mg (70–290), Mn (15–240) and P (0–350). Present in the wood was also Si (50–190), S (50–200) and Cl (30–110). The bark tissues showed much higher element contents; Ca (4800–19,100 ppm) and K (1600–6400) were the dominating elements, followed by Mg (210–2400), P (210–1200), Mn (110–1100) and S (310–750), but the Cl contents (40–330) were only moderately higher in the bark than in the wood. The young foliage (shoots and deciduous leaves) had the highest K (7100–25,000 ppm), P (1600–5300) and S (1100–2600) contents of all tissues, while the shoots of spruce had the highest Cl contents (820–1360) and its needles the highest Si content (5000–11,300). This paper presented a new approach in fuel characterization: the method excludes the presence of impurities, and focus on different categories of plant tissues. This made it possible to discuss the contents of ash element in a wide spectrum of fuel-types, which are of large importance for the energy production in Finland and Sweden.     

NEXT GENERATION ENGINEERED MATERIALS FOR ULTRA SUPERCRITICAL STEAM TURBINES

正1 ABSTRACT To reduce the effect of global warming on our climate,the levels of CO2emissions should be reduced.One way to do this is to increase the efficiency of electricity production from fossil fuels.This will in turn reduce the amount of CO2emissions for a given power output.Using US practice for efficiency calculations,then a move from a typical US plant running at 37%efficiency to a 760℃/38.5 MPa(1 400/5 580 psi)plant running at 48%efficiency would reduce CO2emissions by 170kg/MW.hr or 25%.     

Contents in Volume 23,2014

<正>~~     

Aerodynamic performance effects of leading-edge geometry in gas-turbine blades

The purpose of this paper is to illustrate the advantages of the direct surface-curvature distribution blade-design method, originally proposed by Korakianitis, for the leading-edge design of turbine blades, and by extension for other types of airfoil shapes. The leading edge shape is critical in the blade design process, and it is quite difficult to completely control with inverse, semi-inverse or other direct-design methods. The blade-design method is briefly reviewed, and then the effort is concentrated on smoothly blending the leading edge shape (circle or ellipse, etc.) with the main part of the blade surface, in a manner that avoids leading-edge flow-disturbance and flow-separation regions. Specifically in the leading edge region we return to the second-order (parabolic) construction line coupled with a revised smoothing equation between the leading-edge shape and the main part of the blade. The Hodson–Dominy blade has been used as an example to show the ability of this blade-design method to remove leading-edge separation bubbles in gas turbine blades and other airfoil shapes that have very sharp changes in curvature near the leading edge. An additional gas turbine blade example has been used to illustrate the ability of this method to design leading edge shapes that avoid leading-edge separation bubbles at off-design conditions. This gas turbine blade example has inlet flow angle 0°, outlet flow angle −64.3°, and tangential lift coefficient 1.045, in a region of parameters where the leading edge shape is critical for the overall blade performance. Computed results at incidences of −10°,   −5°,   +5°,   +10° are used to illustrate the complete removal of leading edge flow-disturbance regions, thus minimizing the possibility of leading-edge separation bubbles, while concurrently minimizing the stagnation pressure drop from inlet to outlet. These results using two difficult example cases of leading edge geometries illustrate the superiority and utility of this blade-design method when compared with other direct or inverse blade-design methods.     

Hydrogen production by steam-gasification of carbonaceous materials using concentrated solar energy – V. Reactor modeling,optimization, and scale-up

A chemical reactor for the steam-gasification of carbonaceous particles (e.g. coal, coke) is considered for using concentrated solar radiation as the energy source of high-temperature process heat. A two-phase reactor model that couples radiative, convective, and conductive heat transfer to the chemical kinetics is applied to optimize the reactor geometrical configuration and operational parameters (feedstock's initial particle size, feeding rates, and solar power input) for maximum reaction extent and solar-to-chemical energy conversion efficiency of a 5 kW prototype reactor and its scale-up to 300 kW. For the 300 kW reactor, complete reaction extent is predicted for an initial feedstock particle size up to 35 μm at residence times of less than 10 s and peak temperatures of 1818 K, yielding high-quality syngas with a calorific content that has been solar-upgraded by 19% over that of the petcoke gasified.     

汽轮机数字电液调节系统挂闸异常的技术完善

分析了200MW汽轮机数字电液调节系统在运行中存在的挂闸异常问题,采取了相应的技术处理措施,且运行实践效果良好。     

新型高压共轨ECU升压模块的数字化开发与优化

为了提高喷油器电磁阀的响应速率,提出了一种基于CPLD(复杂可编程逻辑器件)应用于高压共轨ECU的数字升压模块。鉴于该升压电路结构参数多,其升压电压的恢复响应要求高等特征,基于Pspice建立了升压电路的仿真模型,研究了不同电路参数下升压模块的输出特性,全面优化了该升压模块的性能。结果显示,该升压模块的最大转换效率可以达90%以上。在柴油发动机上对ECU的试验表明,升压电压最大波动不超过10%,其恢复时间仅为1.3ms,功率管最大温升仅为41℃,满足整机运行范围内ECU的需求。     

Trace metal chemistry and silicification of microorganisms in geothermal sinter, Taupo Volcanic Zone, New Zealand

As part of a pilot study investigating the role of microorganisms in the immobilisation of As, Sb, B, Tl and Hg, the inorganic geochemistry of seven different active sinter deposits and their contact fluids were characterised. A comprehensive series of sequential extractions for a suite of trace elements was carried out on siliceous sinter and a mixed silica-carbonate sinter. The extractions showed whether metals were loosely exchangeable or bound to carbonate, oxide, organic or crystalline fractions. Hyperthermophilic microbial communities associated with sinters deposited from high temperature (92–94°C) fluids at a variety of geothermal sources were investigated using SEM. The rapidity and style of silicification of the hyperthermophiles can be correlated with the dissolved silica content of the fluid. Although high concentrations of Hg and Tl were found associated with the organic fraction of the sinters, there was no evidence to suggest that any of the heavy metals were associated preferentially with the hyperthermophiles at the high temperature (92–94°C) ends of the terrestrial thermal spring ecosystems studied.     

Assessment methods of material ageing using Sdobyrev''s creep rupture model

The physical aspects of the activation energy, in higher and high temperatures, of the metal creep process were examined. The research results of creep-rupture in a uniaxial stress state and the criterion of creep-rupture in biaxial stress states, at two temperatures, are then presented. For these studies creep-rupture, taking case iron as an example the energy and pseudoenergy activation was determined. For complex stress states the criterion of creep-rupture was taken to be Sdobyrev's, i.e. σ_red = σ₁ β + (1 − β)σ_i, where: σ₁-maximal principal stress, σ_i-stress intensity, β-material constant (at variable temperature β = β(T)). The methods of assessment of the material ageing grade are given in percentages of ageing of new material in the following mechanical properties: 1) creep strength in uniaxial stress state, 2) activation energy in uniaxial stress state, 3) criterion creep strength in complex stress states, 4) activation pseudoenergy in complex stress states. The methods 1) and 3) are the relatively simplest because they result from experimental investigations only at nominal temperature of the structure work, however, for methods 2) and 4) it is necessary to perform the experimental investigations at least at two temperatures.     

Production of hydrogen from sewage biosolids in a continuously fed bioreactor: Effect of hydraulic retention time and sparging

Hydrogen was produced from primary sewage biosolids via mesophilic anaerobic fermentation in a continuously fed bioreactor. Prior to fermentation the sewage biosolids were heated to 70 °C for 1 h to inactivate methanogens and during fermentation a cellulose degrading enzyme was added to improve substrate availability. Hydraulic retention times (HRT) of 18, 24, 36 and 48 h were evaluated for the duration of hydrogen production. Without sparging a hydraulic retention time of 24 h resulted in the longest period of hydrogen production (3 days), during which a hydrogen yield of 21.9 L H₂ kg⁻¹ VS added to the bioreactor was achieved. Methods of preventing the decline of hydrogen production during continuous fermentation were evaluated. Of the techniques evaluated using nitrogen gas to sparge the bioreactor contents proved to be more effective than flushing just the headspace of the bioreactor. Sparging at 0.06 L L min⁻¹ successfully prevented a decline in hydrogen production and resulted in a yield of 27.0  L H₂ kg⁻¹ VS added, over a period of greater than 12 days or 12 HRT. The use of sparging also delayed the build up of acetic acid in the bioreactor, suggesting that it serves to inhibit homoacetogenesis and thus maintain hydrogen production.