Investigation of influence of gas atmosphere and pressure upon non-contact atomic force microscopy

Resonance measurements and atomic force microscopy (AFM) observations were carried out by the non-contact AFM operating in various gas atmospheres (hydrogen, helium, nitrogen and argon) over the range of pressures from 0.1 to 1.1 MPa. In each atmosphere, the resonance frequency of the AFM cantilever depended on the pressure of gases studied. The plots of the relative resonance frequency at a constant pressure vs. the gas density gave a straight line. It was found that the characteristic of the resonance frequency for the AFM cantilever were dependent on the density of the gas species. The resolution of the AFM was hardly influenced by the gas atmosphere under the present experimental conditions.     

Scanning probe microscopy studies of cereal seed storage protein structures

Scanning probe microscopes (SPMs) share a number of common features which give the techniques advantages over conventional light and electron microscopy. First, high resolution, up to the atomic level, is possible in certain cases, and second, they are nondestructive, requiring no staining or coating and the images can be obtained in the hydrated state or under water. Scanning probe microscopes, particularly scanning tunnelling microscopes (STM) and atomic force microscopes (AFM), have been used to study food-related systems, ranging from relatively large structures such as starch granules to the organisation of secondary structures in proteins and the interaction of proteins. The seed storage proteins (gluten) of wheat are responsible for the viscous and elastic properties of wheat doughs that allow them to be used for a wide range of different food products. Using AFM and STM, images of individual and groups of proteins have been obtained in both the dry and hydrated states. The ability to work in liquid environments allows the conformation of proteins to be determined under conditions approaching “native.” The AFM and STM have been used to image both gliadins and glutenins and to study their aggregative behaviour in relation to gluten and dough systems.     

High-pressure scanning tunneling microscopy: tip reactions

Scanning tunneling microscopy (STM) is an ideal tool to image conducting and semiconducting surfaces with atomic resolution. The technique provides high-resolution images in vacuum or even high-pressure environments. Since STM can be operated at elevated pressures and temperatures, images can be collected in situ under catalytic conditions. In this work, we demonstrate that artifacts can be observed when imaging in situ since reactions can occur on the tip, and care should be taken when analyzing the data obtained.     

Dynamic force microscopy imaging of native membranes

We employed magnetic ACmode atomic force microscopy (MACmode AFM) as a novel dynamic force microscopy method to image surfaces of biological membranes in their native environments. The lateral resolution achieved under optimized imaging conditions was in the nanometer range, even when the sample was only weakly attached to the support. Purple membranes (PM) from Halobacterium salinarum were used as a test standard for topographical imaging. The hexagonal arrangement of the bacteriorhodopsin trimers on the cytoplasmic side of PM was resolved with 1.5nm lateral accuracy, a resolution similar to images obtained in contact and tapping-mode AFM. Human rhinovirus 2 (HRV2) particles were attached to mica surfaces via nonspecific interactions. The capsid structure and 2nm sized protein loops of HRV2 were routinely obtained without any displacement of the virus. Globular and filamentous structures on living and fixed endothelial cells were observed with a resolution of 5-20nm. These examples show that MACmode AFM is a favorable method in studying the topography of soft and weakly attached biological samples with high resolution under physiological conditions.     

Imaging streptavidin 2D crystals on biotinylated lipid monolayers at high resolution with the atomic force microscope

Streptavidin crystals were grown on biotinylated lipid monolayers at an air/water interface and transferred onto highly oriented pyrolytic graphite (HOPG). These arrays could be imaged to a resolution below 1 nm using the atomic force microscope. The surface topographs obtained were compared with negative-stain electron microscopy images and the atomic model as determined by X-ray crystallography. The streptavidin tetramer (60 kDa) exposes two free biotin-binding sites to the buffer solution, while two are occupied by linkage to the lipid monolayer. Therefore, the streptavidin 2D crystals can be used as nanoscale matrices for binding biotinylated compounds. Furthermore, this HOPG-based preparation method provides a general novel approach to study the structure of protein arrays assembled on lipid monolayers with the AFM.     

Fractal characterization by frequency analysis: III. Effect of noise

The effect of noise in the fractal characterization by frequency analysis of surface images obtained by scanning tunnelling microscopy (STM), atomic force microscopy (AFM) or profilometry has been studied. The origin of noise and its relationship to the signal is discussed. A procedure to simulate noisy images is presented. From the study it is concluded that the method usually used to characterize noise in STM is not valid and it is shown that fractal characterization of surfaces when noise is present by traditional frequency analysis methods is not possible. A new method to perform both the noise characterization and the fractal characterization of surfaces when noise is present is proposed.     

High speed nano-metrology

For manufacturing at the nanometre scale a method for rapid and accurate measurement of the resultant functional devices is required. Although atomic force microscopy (AFM) has the requisite spatial resolution, it is severely limited in scan speed, the resolution and repeatability of vertical and lateral measurements being degraded when speed is increased. Here we present a new approach to AFM that makes a direct and feedback-independent measurement of surface height using a laser interferometer focused onto the back of the AFM tip. Combining this direct height measurement with a passive, feedback-free method for maintaining tip-sample contact removes the constraint on scan speed that comes from the bandwidth of the z-feedback loop. Conventional laser reflection detection is used for feedback control, which now plays the role of minimising tip-sample forces, rather than producing the sample topography. Using the system in conjunction with a rapid scanner, true height images are obtained with areas up to (36 × 36) μm(2) at 1 image/second, suitable for in-line applications.     

Scanning tunnelling and atomic force microscopy performed with the same probe in one unit

The technique demonstrated here provides features of both scanning tunnelling microscopy (STM) and atomic force microscopy (AFM). The metallic probe acts to record current variations and sense forces from the same sample area simultaneously. Thus, separate images may be recorded, in registry. The collected data allows real space correlations between some electrical properties and the geometric structure of a sample surface. The same tip is used since the geometry and condition of the tip can effect the data recordings. Platinum alloys, tungsten and graphite tips have been employed successfully. An AFM lever can respond to surface contact forces, within the elastic limits of the sample, while electric current is sensed by the tip of the lever. The usefulness of this experimental procedure is tested here by an application to semiconducting samples of Ag-doped CdTe in air and in paraffin oil media.     

Aspect-ratio and lateral-resolution enhancement in force microscopy by attaching nanoclusters generated by an ion cluster source at the end of a silicon tip

One of the factors that limit the spatial resolution in atomic force microscopy (AFM) is the physical size of the probe. This limitation is particularly severe when the imaged structures are comparable in size to the tip's apex. The resolution in the AFM is usually enhanced by using sharp tips with high aspect ratios. In the present paper we propose an approach to modify AFM tips that consists of depositing nanoclusters on standard silicon tips. We show that the use of those tips leads to atomic force microscopy images of higher aspect ratios and spatial resolution. The present approach has two major properties. It provides higher aspect-ratio images of nanoscale objects and, at the same time, enables to functionalize the AFM tips by depositing nanoparticles with well-controlled chemical composition.     

Anomalous voltage dependence of tunnelling microscopy in WSe2

We present scanning tunnelling microscopy (STM) investigations of the layered semiconductor WSe₂. The tunnelling experiments were performed in air and under silicone oil with markedly different results. In air, atomic resolution images of the hexagonally structured surface could be obtained for sample-to-tip voltages of both negative and positive polarities, from ?1·5 to ?0·3 V for negative sample and from +0·6 to +1·6 V for positive sample, respectively. Under silicone oil, however, good atomic images could be seen for negative sample biases down to at least ?14 V, while for positive sample biases no difference with respect to the tunnelling in air was found.     

Scanning tunnelling microscopy of oxidized graphite

Scanning tunnelling microscopy (STM) and transmission electron microscopy (TEM) have been used to investigate the surface of a pyrolitic graphite oxidized in liquid phase by NaClO. Two main features of the oxidized HOPG are revealed by STM. First, a large number of steps of different heights have developed on the graphite surface. These steps can be observed by TEM on another kind of graphite, HSAG 12, but this technique cannot give any information on their heights. Another kind of defect on the previously flat surface of HOPG consists in patches where the surface is rough and perturbed. These domains are very difficult to observe by TEM due to a poor contrast. Thus for the study of surface heterogeneities intentionally created on graphite, STM, providing information along three directions, appears to be complementary of TEM which gives only images of project area.     

A high-pressure atomic force microscope for imaging in supercritical carbon dioxide

A high-pressure atomic force microscope (AFM) that enables in situ, atomic scale measurements of topography of solid surfaces in contact with supercritical CO(2) (scCO(2)) fluids has been developed. This apparatus overcomes the pressure limitations of the hydrothermal AFM and is designed to handle pressures up to 100 atm at temperatures up to ～350 K. A standard optically-based cantilever deflection detection system was chosen. When imaging in compressible supercritical fluids such as scCO(2), precise control of pressure and temperature in the fluid cell is the primary technical challenge. Noise levels and imaging resolution depend on minimization of fluid density fluctuations that change the fluid refractive index and hence the laser path. We demonstrate with our apparatus in situ atomic scale imaging of a calcite (CaCO(3)) mineral surface in scCO(2); both single, monatomic steps and dynamic processes occurring on the (1014) surface are presented. This new AFM provides unprecedented in situ access to interfacial phenomena at solid-fluid interfaces under pressure.     

High-resolution constant-height imaging with apertured silicon cantilever probes

We present high-resolution aperture probes based on non-contact silicon atomic force microscopy (AFM) cantilevers for simultaneous AFM and near-infrared scanning near-field optical microscopy (SNOM). For use in near-field optical microscopy, conventional AFM cantilevers are modified by covering their tip side with an opaque aluminium layer. To fabricate an aperture, this metal layer is opened at the end of the polyhedral probe using focused ion beams (FIB). Here we show that apertures of less than 50 nm can be obtained using this technique, which actually yield a resolution of about 50 nm, corresponding to λ/20 at the wavelength used. To exclude artefacts induced by distance control, we work in constant-height mode. Our attention is particularly focused on the distance dependence of resolution and to the influence of slight cantilever bending on the optical images when scanning at such low scan heights, where first small attractive forces exerted on the cantilever become detectable.     

Atomic force microscopy of a hydrated bacterial surface protein

The protein surface layer of the bacterium Deinococcus radiodurans (HPI layer) was examined with an atomic force microscope (AFM). The measurements on the air-dried, but still hydrated layer were performed in the attractive imaging mode in which the forces between tip and sample are much smaller than in AFM in the repulsive mode or in scanning tunnelling microscopy (STM). The results are compared with STM and transmission electron microscopy (TEM) data.     

The effects of hypobaric atmospheres on living cells in layers of thin media and implications for electron microscopy.

At present, the only possibility for improved resolution of intracellular movement appears to be electron microscopy using a hydration chamber (EMC) at reduced gas pressures with thinned medium around the cells. The environmental constraints of examining cells under such conditions were examined in the absence of ionizing radiation by using an EMC-analogue fitted to a light microscope. White blood cells and baby hamster kidney cells were examined. A 50% survival pressure value, for hypobaric atmospheres, was determined for these cells. Morphological changes of the hypobarically-exposed cells are described.     

Combined atomic force microscopy and scanning tunneling microscopy imaging of cross-sectioned GaN light-emitting diodes

Cross-sectional scanning tunneling microscopy (STM) was combined with atomic force microscopy (AFM) over the same area to characterize a cross-sectioned GaN light emitting diode. Because GaN is typically grown on a non-native substrate and also forms a wurtzite crystal structure, a cryogenic cleaving technique was developed to generate smooth surfaces. The depletion region surrounding the p-n junction was clearly identified using STM. Furthermore, by imaging under multiple sample biases, distinctions between the n-doped and p-doped GaN could be made.     

Contact mechanics and tip shape in AFM-based nanomechanical measurements

Stiffness-load curves obtained in quantitative atomic force acoustic microscopy (AFAM) measurements depend on both the elastic properties of the sample and the geometry of the atomic force microscope (AFM) tip. The geometry of silicon AFM tips changes when used in contact mode, affecting measurement accuracy. To study the influence of tip geometry, we subjected ten AFM tips to the same series of AFAM measurements. Changes in tip shape were observed in the scanning electron microscope (SEM) between individual AFAM tests. Because all of the AFAM measurements were performed on the same sample, variations in AFAM stiffness-load curves were attributed to differences in tip geometry. Contact-mechanics models that assumed simple tip geometries were used to analyze the AFAM data, but the calculated values for tip dimensions did not agree with those provided by SEM images. Therefore, we used a power-law approach that allows for a nonspherical tip geometry. We found that after several AFAM measurements, the geometry of the tips at the very end is intermediate between those of a flat punch and a hemisphere. These results indicate that the nanoscale tip-sample contact cannot easily be described in terms of simple, ideal geometries.     

Topographic characterization of unworn contact lenses assessed by atomic force microscopy and wavelet transform

This paper analyses the three‐dimensional (3‐D) surface morphology of optic surface of unworn contact lenses (CLs) using atomic force microscopy (AFM) and wavelet transform. Refractive powers of all lens samples were 2.50 diopters. Topographic images were acquired in contact mode in air‐conditioned medium (35% RH, 23°C). Topographic measurements were taken over a 5 µm × 5 µm area with 512 pixel resolution. Resonance frequency of the tip was 65 kHz. The 3‐D surface morphology of CL unworn samples revealed (3‐D) micro‐textured surfaces that can be analyzed using (AFM) and wavelet transform. AFM and wavelet transform are accurate and sensitive tools that may assist CL manufacturers in developing CLs with optimal surface characteristics. Microsc. Res. Tech. 78:1026–1031, 2015. © 2015 Wiley Periodicals, Inc.     

Comparative study of the conditions required to image live human epithelial and fibroblast cells using atomic force microscopy

Successful imaging of living human cells using atomic force microscopy (AFM) is influenced by many variables including cell culture conditions, cell morphology, surface topography, scan parameters, and cantilever choice. In this study, these variables were investigated while imaging two morphologically distinct human cell lines, namely LL24 (fibroblasts) and NCI H727 (epithelial) cells. The cell types used in this study were found to require different parameter settings to produce images showing the greatest detail. In contact mode, optimal loading forces ranged between 2-2.8 x 10(-9) and 0.1-0.7 x 10(-9) (N) for LL24 and NCI H727 cells respectively. In tapping (AC) mode, images of LL24 cells were obtained using cantilevers with a spring constant of at least 0.32 N/m, while NCI H727 cells required a greater spring constant of at least 0.58 N/m. To obtain tapping mode images, cantilevers needed to be tuned to resonate at higher frequencies than their resonance frequencies to obtain images. For NCI H727 cells, contact mode imaging produced the clearest images. For LL24 cells, contact and tapping mode AFM produced images of comparable quality. Overall, this study shows that cells with different morphologies and surface topography require different scanning approaches and optimal conditions must be determined empirically to achieve images of high quality.     

In-situ STM studies of electrochemical underpotential deposition of Pb on Au(111)

A modified scanning tunnelling microscope (STM) has been used to observe in-situ deposition and stripping of an electrochemical film. With STM tip and sample immersed in an acid electrolyte, single atomic steps on Au(111) have been imaged during the deposition and stripping of a monolayer-thick, underpotential deposit (UPD) of Pb. Integration of the electrochemical current passed during the film deposition and evidence from the STM images themselves confirm monolayer coverage. Our images show enhanced film growth at step edges and defect sites. Observations of single plating and stripping cycles indicate that the Au substrate returns unaltered. Except for atomic resolution images of Au(111), which we have not yet achieved in an electrolyte, all types of Au surface features seen in air are reproduced under the electrolytic solution. The modifications made to our STM in order to perform in-situ electrochemical experiments are described.