抗菌不锈钢及其在炊具领域中的应用

抗菌不锈钢是新开发的一种新型抗菌材料，兼具抗菌、装饰美化和结构材料的多重功能，其使用范围扩展到现有的有机抗菌剂和无机抗菌剂及其制品无法涵盖的许多领域，特别是要求高强度、耐高温、耐磨擦的场合，为制造新型炊具、食品加工设备以及医疗器械和公用设施提供了新材料。相关制品的自清洁抗菌作用能够有效地预防病菌传播、防止交叉感染和提高公共卫生水平。本文简要介绍了抗菌不锈钢的抗菌特性、在抗菌钢作用下细菌的演化过程和抗菌不锈钢在相关领域的可能应用。     

Semivolatile and volatile organic compound emissions from wood-fired hydronic heaters

Emissions including polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs), polyaromatic hydrocarbons (PAHs), and volatile organic compounds (VOCs), were sampled from different wood-fired hydronic heater (HH) technologies. Four commercially available HH technologies were studied: a single-stage conventional combustor with natural updraft, a three-stage downdraft combustion system, a bottom-fed pellet burner, and a two-stage heater with both a combustion and gasification chamber. The fuel consisted of three wood types (red oak, white pine, and white ash), one hardwood pellet brand, and one fuel mixture containing 95% red oak and 5% residential refuse by weight. The various HHs and fuel combinations were tested in a realistic homeowner fuel-charging scenario. Differences in emission levels were found between HH technologies and fuel types. PCDD/PCDF emissions ranged from 0.004 to 0.098 ng toxic equivalency/MJ(input) and PAHs from 0.49 to 54 mg/MJ(input). The former was increased by the presence of 5% by weight refuse. The white pine fuel had the highest PAH emission factor, while the bottom fed pellet burner had the lowest. The major VOCs emitted were benzene, acetylene, and propylene. The highest emissions of PAHs, VOCs, and PCDDs/PCDFs were observed with the conventional unit, likely due to the rapid changes in combustion conditions effected by the damper opening and closing.     

On quantitative determination of volatile organic compound concentrations using proton transfer reaction time-of-flight mass spectrometry

Proton transfer reaction - mass spectrometry (PTR-MS) has become a reference technique in environmental science allowing for VOC monitoring with low detection limits. The recent introduction of time-of-flight mass analyzer (PTR-ToF-MS) opens new horizons in terms of mass resolution, acquisition time, and mass range. A standard procedure to perform quantitative VOC measurements with PTR-ToF-MS is to calibrate the instrument using a standard gas. However, given the number of compounds that can be simultaneously monitored by PTR-ToF-MS, such a procedure could become impractical, especially when standards are not readily available. In the present work we show that, under particular conditions, VOC concentration determinations based only on theoretical predictions yield good accuracy. We investigate a range of humidity and operating conditions and show that theoretical VOC concentration estimations are accurate when the effect of water cluster ions is negligible. We also show that PTR-ToF-MS can successfully be used to estimate reaction rate coefficients between H(3)O(+) and VOC at PTR-MS working conditions and find good agreement with the corresponding nonthermal theoretical predictions. We provide a tabulation of theoretical rate coefficients for a number of relevant volatile organic compounds at various energetic conditions and test the approach in a laboratory study investigating the oxidation of alpha-pinene.     

Qualitative and quantitative characterization of volatile organic compound emissions from cut grass

Mechanical wounding of plants triggers the release of a blend of reactive biogenic volatile organic compounds (BVOCs). During and after mowing and harvesting of managed grasslands, significant BVOC emissions have the potential to alter the physical and chemical properties of the atmosphere and lead to ozone and aerosol formation with consequences for regional air quality. We show that the amount and composition of BVOCs emitted per unit dry weight of plant material is comparable between laboratory enclosure measurements of artificially severed grassland plant species and in situ ecosystem-scale flux measurements above a temperate mountain grassland during and after periodic mowing and harvesting. The investigated grassland ecosystem emitted annually up to 130 mg carbon m(-2) in response to cutting and drying, the largest part being consistently represented by methanol and a blend of green leaf volatiles (GLV). In addition, we report the plant species-specific emission of furfural, terpenoid-like compounds (e.g., camphor), and sesquiterpenes from cut plant material, which may be used as tracers for the presence of given plant species in the ecosystem.     

Online volatile organic compound measurements using a newly developed proton-transfer ion-trap mass spectrometry instrument during New England Air Quality Study--Intercontinental Transport and Chemical Transformation 2004: performance, intercomparison, and compound identification

We have used a newly developed proton-transfer ion-trap mass spectrometry (PIT-MS) instrument for online trace gas analysis of volatile organic compounds (VOCs) during the 2004 New England Air Quality Study-Intercontinental Transport and Chemical Transformation study. The PIT-MS instrument uses proton-transfer reactions with H3O+ ions to ionize VOCs, similarto a PTR-MS (proton-transfer reaction mass spectrometry) instrument but uses an ion trap mass spectrometer to analyze the product ions. The advantages of an ion trap are the improved identification of VOCs and a near 100% duty cycle. During the experiment, the PIT-MS instrument had a detection limit between 0.05 and 0.3 pbbv (S/N = 3 (signal-to-noise ratio)) for 2-min integration time for most tested VOCs. PIT-MS was used for ambient air measurements onboard a research ship and agreed well with a gas chromatography mass spectrometer). The comparison included oxygenated VOCs, aromatic compounds, and others such as isoprene, monoterpenes, acetonitrile, and dimethyl sulfide. Automated collision-induced dissociation measurements were used to determine the contributions of acetone and propanal to the measured signal at 59 amu; both species are detected at this mass and are thus indistinguishable in conventional PTR-MS.     

Concentration of volatile compounds in Chardonnay wine fermented in stainless steel tanks and oak barrels

The influence of the type of container used in alcoholic fermentation on the formation of volatile compounds in wine from Chardonnay variety was studied. To do so, must from Chardonnay variety was fermented in both stainless steel tanks and in new Nevers oak barrels. The results obtained showed that wine fermented in barrels had a greater concentration of higher alcohols and esters than wine fermented in tanks. Concentration of isoamyl acetate, ethyl hexanoate, ethyl octanoate and ethyl decanoate was four times higher in wine fermented in oak barrels than in wine fermented in stainless steel tanks. With regard to the concentration of acids, a greater concentration of medium-chain fatty acids (C6:0–C10:0) was noticeable in wine fermented in oak barrels. Given that these acids are toxic for the yeasts, they may be responsible for the slower fermentation rate of wine fermented in oak barrels.     

Characterization and comparison of three passive air samplers for persistent organic pollutants

The accumulation of persistent organic pollutants by three passive sampling media--semipermeable membrane devices (SPMDs), polyurethane foam (PUF) disks, and an organic-rich soil--was investigated. The media were exposed to contaminated indoor air over a period of 450 days, and concentrations in the air and in the media were monitored for individual polychlorinated biphenyl (PCB) congeners and polychlorinated naphthalene homologue groups. Uptake was initially linear and governed by the surface area of the sampler and the boundary layer airside mass transfer coefficient (MTC). Mean values of the MTC were 0.13, 0.11, and 0.26 cm s-1 for SPMD, PUF, and soil, respectively. As the study progressed, equilibrium was established between ambient air and the passive sampling media for the lower molecular weight PCB congeners. This information was used to calculate passive sampler-air partition coefficients, KPSM-A. These were correlated to the octanol-air partition coefficient, and the resulting regressions were used to predict KPSM-A for the full suite of PCBs. Information on MTC, KPSM-A, surface area, and effective thickness of each sampler was used to estimate times to equilibrium for each medium. These ranged from tens of days for the lower molecular weight congeners to tens of years for the higher molecular weight PCBs. Expressions were also developed to relate the amount of chemical accumulated by the passive sampling media to average ambient air concentrations over the integration period of the sample.     

大体积顶空联用固相微萃取法测定有机挥发物

采用大体积顶空和固相微萃取联用方法,通过气相色谱.质谱定性定量分析纺织品中有机挥发物(氯乙烯、1,3-丁二烯、甲苯、乙烯基环己烯、苯乙烯和4-苯基环己烯)的残留量.本方法对甲苯、乙烯基环己烯、苯乙烯和4-苯基环己烯的检出限低于0.001 mg/m2,对氯乙烯和1,3-丁二烯的检出限为0.08 mg/m2,加标回收率为95%~107%,相对标准偏差小于8%.     

地毯有机挥发物的ETC-ATD-GC/MS联用测试法

采用环境测试舱(ETC)、自动热脱附仪(ATD)和气相色谱/质谱(GC/MS)联用技术,建立了地毯中13种挥发性有机物(VOCs)的分析方法。该方法对VOCs单体的最小检出限(LODs)范围为0.008～0.4μg/m~3,方法的加标回收率为90%～106%,相对标准偏差(RSD)小于11%。将该方法用于多种市售地毯的VOCs测试,发现地毯释放VOCs的种类,与地毯底层材料有较大关联,沥青底胶层的方块地毯释放出较多的2-乙基-1-己醇,黄麻背衬地毯和聚酯背衬地毯释放出较多的苯乙烯和4-苯基环己烯,而薄层聚丙烯背衬地毯则释放出较多的直链或支链烷烃。     

Comparison of two field sampling procedures (En Core and field methanol extraction) for volatile organic compounds

In-situ Lasagna technology was recently evaluated at a contaminated site at Offutt Air Force Base. The site was contaminated with low levels (<30 mg/kg) of volatile organic compounds (VOCs). Originally, researchers planned to use field methanol extraction for both pre- and post-treatment sampling to evaluate the effectiveness of the technology on contaminant reduction. Precharacterization sampling, however, indicated that concentrations of some contaminants of concern were much lower than expected. Because use of methanol increases the detection limit, it was probable that post-treatment concentrations of these target contaminants would be nondetectable if methanol extraction was used. Project management, therefore, decided to use En Core samplers in addition to field methanol extraction during the pretreatment sampling event. The En Core sampling approach, while yielding a lower detection limit, uses discreet samples along the length of a core, whereas the methanol extraction approach samples the entire length of the core. The concern was that discreet samples may bias results if any "hot spots" were present. The two field sampling procedures, En Core and field methanol extraction, were performed side-by-side during the pretreatment phase of the technology evaluation in order to determine if the concern was valid for this site. Results were compared for four contaminants of concern: trichloroethylene, vinyl chloride, cis-1,2-dichloroethene, and trans-1,2-dichloroethene. The two procedures produced similar results with respect to both the concentration means and the variances, and no bias was evident. This finding supports project management's decision to use only En Core samplers post-treatment due to low concentrations of target contaminants.     

The diversity of microbial communities in Chinese milk fan and their effects on volatile organic compound profiles

Milk fan is a cheese-like fermented milk product produced in Yunnan Province, China. In this study, we characterized the microbial communities of milk fan from 6 distinct geographical origins and investigated their generation of volatile organic compounds (VOC). The microbial communities found in all milk fan samples were dominated by Lactococcus, Lactobacillus, and Raoultella bacteria and Rhodotorula, Torulaspora, and Candida fungi. Samples from the Kunming and Weishan regions had greater bacterial richness, and samples from Xizhou had greater fungal community richness. Sixty prominent VOC (i.e., those having odor activity values ≥1), including esters, acids, alcohols, aldehydes, ketones, and aromatic compounds, were identified by gas chromatography-mass spectrometry analysis of milk fan samples. Pearson correlation analysis revealed that Lactobacillus, Rhodotorula, Lodderomyces, and Debaryomyces had significant correlations with various VOC, revealing a total of 13 compounds that are characteristic of the odor of milk fan. These bacteria and fungi are therefore identified as functional microorganisms that collectively create the complex VOC profile of milk fan. This study provides a comprehensive overview of the microbial community of milk fan and demonstrates its contribution to the unique aroma profile of this fermented milk product     

Effectiveness of sanitation with quaternary ammonium compound or chlorine on stainless steel and other domestic food-preparation surfaces.

The relative ability of various materials used for domestic and/or food-service sinks and countertops to be sanitized was determined. Both smooth (unused) and abraded surfaces were tested by exposure to 200 mg of quaternary ammonium compound per liter or 200 mg of sodium hypochlorite per liter. Surface materials tested included mechanically polished (type 304, #4 finish) and electropolished stainless steel, polycarbonate, and mineral resin. Surfaces were prepared for testing by allowing attachment of a Staphylococcus aureus culture for 4 h to achieve an initial attached population of 10(4) to 10(5) CFU/cm2. The test procedure involved immersion of the surface in sanitizer solution followed by wiping with a sanitizer-saturated cloth. Residual staphylococci were detected by overlaying agar directly on the treated surface. Results indicated that the stainless steels and the smooth polycarbonate, which had 0.5 log CFU/cm2 or fewer of residual staphylococci, were more readily sanitized by quaternary ammonium compound than were either the mineral resin surfaces, which had nearly 2.0 log CFU/cm2 of residual staphylococci, or the abraded polycarbonate which had nearly 1.0 log CFU/cm2 of residual staphylococci. Chlorine was most effective on the mechanically polished stainless steel, the unabraded electropolished stainless steel, and the polycarbonate surfaces, reducing cell populations to less than 1.0 log CFU/cm2. Chlorine was less effective on abraded electropolished stainless steel and mineral resin surfaces, where populations remained greater than 1.0 log CFU/cm2. Sanitation with quaternary ammonium compound or chlorine reduced S. aureus populations more than 1,000-fold on all surfaces except unabraded mineral resin.     

The potential of volatile organic compound analysis in cervicovaginal mucus to predict estrus and ovulation in estrus-synchronized heifers

Cervicovaginal mucus is a mixture of mucins, ions, salts, and water, the proportions of which change during the reproductive cycle. It is suspected that this mucus emits an important volatile signal indicative of the reproductive state of the female. The objective of this study was to identify volatile organic compounds (VOC) in bovine cervicovaginal mucus that are modulated during the estrous cycle and could potentially be used as biomarkers of estrus and ovulation. Cervicovaginal mucus was collected from crossbred beef heifers (n = 8), which were synchronized using an 8-d controlled internal drug release (CIDR) protocol and in which onset of estrus and time of ovulation were determined by visual observation and ultrasonography, respectively. Mucus samples were collected between 0 and 96 h after CIDR removal (estrus onset occurred at 49.1 ± 3.3 h after CIDR removal). A validation study was performed on an independent group of 15 heifers from which cervicovaginal mucus samples were collected every 8 h from 40 to 80 h after CIDR removal. The VOC in mucus were identified using gas chromatography-mass spectrometry and selected compounds were quantified using selected-ion flow-tube mass spectrometry. The presence of 47 VOC was detected in mucus samples by gas chromatography-mass spectrometry with those exhibiting highest abundance including 2-butanone, acetone, 2-pentanone, 4-methyl-2-pentanone, 1-(1-methylethoxy)-2-propanone, ethanol, 2-methyl-2-propanol, and 2-butanol. All VOC peaked between 24 to 47 h after the onset of estrus (ovulation occurred 26.6 ± 5.6 h after estrus onset). Two VOC, 2-pentanone and 4-methyl-2-pentanone, exhibited a significant increase at the onset of estrus, whereas concentration of 2-butanone increased significantly just after estrus onset, indicating that these VOC may be used as putative biomarkers of estrus. The results of our study may contribute to the development of a sensor device based on VOC to aid the detection of estrus and ovulation in cattle, with particular relevance for the dairy industry where the majority of females are bred by artificial insemination.     

Modeling atmospheric vegetation uptake of PBDEs using field measurements

Polybrominated diphenyl ethers (PBDEs) are flame retardants used in a variety of consumables. Models indicate that air-vegetation exchange plays an important role in their global distribution. The present study surveyed PBDEs in spruce needles and air (gaseous and particulate-bound) over an annual cycle to model accumulation of PBDEs in vegetation. Air-particulate distributions revealed that penta and higher BDE congeners were mainly associated with particulates even in warmer temperatures, whereas for the tri- and tetra-BDE congeners, a significant temperature dependence was observed. Using measured vegetation and atmospheric concentrations from bud burst 2004 to June 2005, a modeling concept was developed to determine PBDE deposition velocities to vegetation. Particulate-bound deposition velocity was calculated to be 3.8 m/h. Net gaseous transfer velocities ranged from 2.4 to 62.2 m/h and correlated significantly with log K(OA). These derived values were used to model PBDE accumulation by vegetation through time, and these agreed well with measured values. This study provides the necessary background for modeling PBDE transport between air and coniferous vegetation globally.     

不锈录井钢丝的评估与试制

介绍国内外不锈录井钢丝分类、使用状况以及试制技术指标,对高品质不锈录井钢丝进行评估,并试制Sw960,Sw970两种牌号不锈录井钢丝。根据合金元素含量及其组合匹配,分析提高不锈录井钢丝综合性能,尤其是耐应力腐蚀破断能力水平的方法;从控制固溶处理工艺与拉拔工艺出发,找出钢丝在拉拔过程中防止脆断的途径;探讨碳含量对奥氏体铬镍钼不锈钢录井钢丝腐蚀性能的影响,结果表明,试制的不锈录井钢丝抗拉强度和显微硬度较低,韧性较好;显微组织与进口不锈录井钢丝相似;对腐蚀介质H2S耐应力腐蚀开裂能力与国外产品水平相当。     

皮革工业用有机硅化合物的研究进展(续)

皮革涂饰剂一般由成膜物质、着色物、溶剂(水或有机溶剂)以及各种添加组分(如防水剂、滑爽剂、光亮剂、防粘剂、增塑剂等)组成。由于有机硅的优良综合性能，其耐热耐寒性好，粘温系数小，耐候性优良，疏水，耐磨，可以用来改性通常使用的丙烯酸树脂涂饰剂，使之涂饰性能更加优良。再者，因其表面张力小，易于润     

Evaluating competitive sorption mechanisms of volatile organic compounds in soils and sediments using polymers and zeolites

The competitive sorption of trichloroethene (TCE) and tetrachloroethene (PCE) was investigated in three natural solids, two polymers, and four zeolites. Competition was observed in natural solids with high contents of recalcitrant organic carbon, in the glassy polymer, and in zeolites with strongly and moderately hydrophobic micropores of large (7.5 x 10 A) and small pore widths (approximately 5.4 A), respectively. Isotherm results and recalcitrant OC% values for natural solids indicate that the extent of competition between TCE and PCE is related to the amount of hard organic carbon. Gas adsorption results and the variability in C/H values suggest that natural organic matter contains micropores with varying width and polarity. Isotherm results for zeolites indicate that competition between TCE and PCE increases with increasing hydrophobicity and decreasing micropore width. We suggest that competition between volatile organic contaminants in the subsurface is controlled by competition for hydrophobic micropores in hard organic matter and that smaller more hydrophobic micropores result in stronger competition.