Filamentous carbon templated SiO2–NiO aerogel: structure and catalytic properties for direct oxidation of hydrogen sulfide into sulfur

Silica aerogels comprising nickel oxide nanoparticles were synthesized with no use of supercritical drying. A high specific surface area (more than 1000 m²/g), mesoporous structure and considerable stability to sintering up to 900 °C are characteristic of these aerogels. The aerogels were synthesized using the sol–gel method. Filamentous carbon was templated by silica, tetraethoxysilane being used for supplying silica. Carbon was burnt later. Analysis of the aerogel structure revealed the presence of silica nanotubes and nanofibers. Aerogel testing for direct oxidation of H₂S into S⁰ demonstrated as high as 60% conversion of hydrogen sulfide at almost 100% selectivity under stoichiometric conditions at the temperature range of 300–350 °C and 73% conversion at 100% selectivity at a considerable excess of oxygen at 160 °C. This revised version was published online in July 2006 with corrections to the Cover Date.     

Capacity of Cr(VI) reduction in an aqueous solution using different sources of zerovalent irons

Zerovalent iron (ZVI) has drawn intense interest as an effective and inexpensive tool to enhance degradation of various environmental contaminants. Reduction of Cr(VI) to Cr(III) by ZVI merits environmental concern as a hazardous species is transformed into a non-hazardous one. Objectives of this research were to assess kinetics and capacity of Cr(VI) reduction by different sources of ZVIs, of which chemical parameters can base in situ application of ZVI to treat Cr(VI) contaminated water. Reduction kinetics were first-order and rapid showing that 50% of the initial Cr(VI) was reduced within 7.0 to 347 min depending on Cr(VI) concentration, temperature and ZVI source. The reduction rates were increased with decreasing the initial Cr(VI) concentrations and increasing the reaction temperatures. The J ZVI (Shinyo Pure Chemical Co., Japan) was more effective in Cr(VI) reduction than PU (Peerless Metal Powders, USA). The maximum reduction capacities of J and PU ZVIs at 25°C were 0.045 and 0.042 mmol g⁻¹ Fe⁰, respectively. A relatively higher value of the net reaction energy (E _a ) indicated that Cr(VI) reduction by ZVI was temperature dependent and controlled by surface properties of ZVI. Chemical parameters involved in the Cr(VI) reduction by ZVI such as temperature quotient, kinetic rates, and stoichiometry indicated that the ZVI might be effective for in situ treatment of the Cr(VI) containing wastewater.     

Foreign element doping and thermal stability of alumina aerogels

The addition of foreign elements is considered as an effective method to improve the thermal stability of alumina aerogels at a higher temperature. However, the location and stabilizing mechanism of the foreign elements in the alumina aerogel have not been carefully studied. In this work, Si or La was introduced into the network of alumina aerogels through a sol-gel strategy. The Si-doped alumina aerogel maintained high surface area (92 m²/g) and pore volume (0.572 cm³/g) even at 1300°C. The dopants prevented α-Al₂O₃ transformation at elevated temperatures (1200°C–1300°C). The distribution of foreign ions and their stabilizing mechanism were discussed in detail. The doped alumina aerogels reinforced by mullite fiber felt, with quite low density and thermal conductivity, can be used as high-temperature thermal insulations.     

Enhancing electrochemical performance of Fe3O4/graphene hybrid aerogel with hydrophilic polymer

Graphene hybrid aerogels have attracted attention as electrode materials because of their unique porous architectures. However, their electrochemical performance is limited by the intrinsic hydrophobicity and the ease of aggregation of graphene nanosheets. We demonstrate a unique methodology to produce graphene hybrid aerogels through assembly of graphene nanosheets, nanometer‐scale ferroferric oxide (Fe₃O₄), and hydrophilic poly(vinyl alcohol) (PVA) into three‐dimensional hierarchical macrostructures. Electrochemical performance measurements exhibit a significant improvement in the specific capacitance of this ternary hybrid aerogel with remarkable cycling stability. Specifically, the specific capacitance is nearly 6.6 times higher than that of the neat graphene aerogel, and a cycling capacitance retention rate of 99% was achieved after 2000 cycles at a high current density of 0.5 A g^?1. Electrochemical impedance spectroscopy measurements demonstrate a lower resistance in the Fe₃O₄/graphene/PVA aerogel electrode compared with that of both neat graphene and Fe₃O₄/graphene aerogel electrodes. The obtained graphene hybrid aerogels with outstanding cycling performance and high energy density are very promising as electrode materials for supercapacitors. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45566.     

Hydrodechlorination of trichloroethene using stabilized Fe-Pd nanoparticles: Reaction mechanism and effects of stabilizers, catalysts and reaction conditions

This study investigated the effects of carboxymethyl cellulose (CMC) as a stabilizer on the reactivity of CMC-stabilized Fe-Pd bimetallic nanoparticles toward trichloroethene (TCE). Overall, the particle stabilization prevented particle agglomeration and resulted in greater particle reactivity. The pseudo-first order TCE degradation rate increased from 0.86 h⁻¹ to 6.8 h⁻¹ as the CMC-to-Fe molar ratio increased from 0 to 0.0124. However, a higher CMC-to-Fe ratio inhibited the TCE degradation. Within the same homologous series, CMC of greater molecular weight resulted in more reactive nanoparticles for TCE hydrodechlorination. Hydrogen (either residual hydrogen from zero-valent iron (ZVI) nanoparticle synthesis or hydrogen evolved from ZVI corrosion) can serve as effective electron donors for TCE dechlorination in the presence of Pd (either coated on ZVI or as separate nanoparticles). Decreasing reaction pH from 9.0 to 6.0 increased the TCE reduction rate by 11.5 times, but enhanced the Fe corrosion rate by 31.4 times based on the pseudo-first order rate constant. Decreasing pH also shifted the rate controlling step of TCE reduction from Fe corrosion to hydrodechlorination. Ionic strength (<0.51 M) did not significantly affect the TCE reduction.     

Structural and thermoelectric properties of hydrothermal-processed Ag-doped Fe2O3

Fe_2-xAg_xO₃ (0?≤?x?≤?0.04) nanopowders with various Ag contents were synthesized at different hydrothermal reaction temperatures (150?°C and 180?°C). Their structural properties were fully investigated through an X-ray diffraction, a Fourier transform infrared spectroscopy, and an X-ray photoelectron spectroscopy. The hydrothermal reaction temperature, time, and Ag content remarkably affected the morphological characteristics and crystal structure of the synthesized powders. The Fe_2-xAg_xO₃ (0?≤?x?≤?0.04) powders synthesized at 150?°C for 6?h and the Fe_2-xAg_xO₃ (0.02?≤?x?≤?0.04) powders synthesized at 180?°C for 12?h formed the orthorhombic α-FeOOH phase with a rod-like morphology, whereas the Fe_2-xAg_xO₃ (0?≤?x?≤?0.01) powders synthesized at 180?°C for 12?h formed the rhombohedral α-Fe₂O₃ phase with a spherical-like morphology. The Fe_1.98Ag_0.02O₃ fabricated by utilizing Fe_1.98Ag_0.02O₃ powders synthesized at 180?°C showed the largest power factor (0.64?×10^?5 Wm^?1 K^?2) and dimensionless figure-of-merit (0.0036) at 800?°C.     

Influence of mixed-surfactant on reductive dechlorination of trichloroethylene by zero-valent iron

Mixed nonionic and cationic surfactants were used to enhance the reductive dechlorination rate of trichloroethylene (TCE) with zero valent iron (ZVI). Among tested combinations of four cationic and three nonionic surfactants, a mixed surfactant system of hexadecyl-trimethyl ammonium (CTAB) and Brij30 at a mixing ratio of 1: 1 with 0.5 critical micelle concentration (CMC) exhibited the highest reaction rate constant, 0.0269 h⁻¹; the dechlorination rate constant of TCE with ZVI in the absence of surfactant was 0.0206 h⁻¹. The effect of this mixed surfactant on the reductive dechlorination of TCE was investigated using ZVI in a column to simulate field conditions. Unlike batch tests, column tests of the mixed surfactant system exhibited higher and lower TCE removal as compared to a nonionic and a cationic surfactant system, respectively. Consequently, if surfactants are applied for surfactant-enhanced aquifer remediation (SEAR), the performance of a permeable reactive barrier (PRB) system using ZVI to remove the residual TCE in groundwater might be affected by surfactant types; thus, the application should be carefully considered.     

Preparation, electrochemical properties, and cycle mechanism of Li1? x Fe0.8Ni0.2O2-Li x MnO2 (Mn/(Fe+Ni+Mn)=0.8) material

A new type of Li_1−x Fe_0.8Ni_0.2O₂-Li _x MnO₂ (Mn/(Fe+Ni+Mn)=0.8) material was synthesized at 350 °C in an air atmosphere by a solid-state reaction. The material had an XRD pattern that closely resembled that of the original Li_1−x FeO₂-Li _x MnO₂ ((Fe+Ni+Mn)=0.8) with much reduced impurity peaks. It was composed of many large particles of about 500–600 nm and small particles of about 100–200 nm, which were distributed among the larger particles. The Li/Li_1−x Fe_0.8Ni_0.2O₂-Li _x MnO₂ cell showed a high initial discharge capacity above 192 mAh/g, which was higher than that of the parent Li/Li_1−x FeO₂-Li _x MnO₂ (186 mAh/g). This cell exhibited not only a typical voltage plateau in the 2.8 V region, but also an excellent cycle retention rate (96%) up to 45 cycles. We suggest a unique role of doped nickel ion in the Li/Li_1−x Fe_0.8Ni_0.2O₂-Li _x MnO₂ cell, which results in the increased initial discharge capacity from the redox reaction of Ni²⁺/Ni³⁺ between 2.0 and 1.5 V region.     

Formation of BaFe12−xNbxO19 and its high electromagnetic wave absorption properties in millimeter wave frequency range

BaFe_12?xNb_xO₁₉ (BFNO, x=0‐0.6) powders with Nb⁵⁺ substituting for Fe³⁺ were prepared by sol‐gel method. The formation process and electromagnetic (EM) wave absorption properties of the BFNO are investigated in detail. With Nb⁵⁺ content increasing from x=0 to x=0.6, the formation temperature of barium ferrite phase without heat time increases from ~700°C to ~900°C, while the appearance temperature of typical plate grains decreases from ~1300°C to ~1100°C, and the crystallization ability decreases at 600°C‐900°C, while the grain size increases gradually at 1100°C‐1300°C. Increasing sintering temperature and time promote the formation of barium ferrite phase and grain growth in all the samples. The ε′ and ε″ of the sample with x=0.6 sintered at 1300°C for 3 hours reach highest of ~7.9 and ~0.95 over 26.5‐40 GHz. Multiresonance peaks in permeability decrease from 40+ GHz to ~30 GHz with x rising from 0 to 0.6. Ultimately, small RL_min of ~?42 dB, thin d_m of ~0.76 mm, and broad bandwidth of >12 GHz can be exhibited simultaneously around millimeter wave atmospheric window of 35 GHz.     

Structural,Raman, and Dielectric Studies on Multiferroic Mn‐doped Bi1−xLaxFeO3 Ceramics

Multiferroic Bi_1?xLa_xFeO₃ [BLFO (x)] ceramics with x = 0.10–0.50 and Mn‐doped BLFO (x = 0.30) ceramics with different doping contents (0.1–1.0 mol%) were prepared by solid‐state reaction method. They were crystallized in a perovskite phase with rhombohedral symmetry. In the BLFO (x) system, a composition (x)‐driven structural transformation (R3c→C222) was observed at x = 0.30. The formation of Bi₂Fe₄O₉ impure phase was effectively suppressed with increasing the x value, and the rhombohedral distortion in the BLFO ceramics was decreased, leading to some Raman active modes disappeared. A significant red frequency shift (~13 cm^?1) of the Raman mode of 232 cm^?1 in the BLFO ceramics was observed, which strongly perceived a significant destabilization in the octahedral oxygen chains, and in turn affected the local FeO₆ octahedral environment. In the Mn‐doped BLFO (x = 0.30) ceramics, the intensity of the Raman mode near 628 cm^?1 was increased with increasing the Mn‐doping content, which was resulted from an enhanced local Jahn–Teller distortions of the (Mn,Fe)O₆ octahedra. Electron microscopy images revealed some changes in the ceramic grain sizes and their morphologies in the Mn‐doped samples at different contents. Wedge‐shaped 71° ferroelectric domains with domain walls lying on the {110} planes were observed in the BLFO (x = 0.30) ceramics, whereas in the 1.0 mol% Mn‐doped BLFO (x = 0.30) samples, 71° ferroelectric domains exhibited a parallel band‐shaped morphology with average domain width of 95 nm. Dielectric studies revealed that high dielectric loss of the BLFO (x = 0.30) ceramics was drastically reduced from 0.8 to 0.01 (measured @ 10⁴ Hz) via 1.0 mol% Mn‐doping. The underlying mechanisms can be understood by a charge disproportion between the Mn⁴⁺ and Fe²⁺ in the Mn‐doped samples, where a reaction of Mn⁴⁺ + Fe²⁺→Mn³⁺ + Fe³⁺ is taken place, resulting in the reduction in the oxygen vacancies and a suppression of the electron hopping from Fe³⁺ to Fe²⁺ ions effectively.     

Enhanced negative thermal expansion of (KMg)3+-substituted Fe2Mo3O12 ceramics

Herein, we report the solid-state synthesis of (KMg)_xFe_2-xMo₃O₁₂ (0 = x ≤ 1.5) ceramics. Phase composition, crystal structure, morphology, phase transition and thermal expansion behavior of the (KMg)_xFe_2-xMo₃O₁₂ ceramics were investigated by XRD, Raman, XPS, HRTEM, EDX, SEM, TMA and high-temperature XRD. Results indicate that (KMg)³⁺ dual-cations have successfully replaced Fe³⁺ in Fe₂Mo₃O₁₂ ceramics and single-phase monoclinic (KMg)_xFe_2-xMo₃O₁₂ ceramics were prepared for 0.25 = x ≤ 1. (KMg)³⁺ introduction can increase the density of (KMg)_xFe_2-xMo₃O₁₂ ceramics and effectively improve their negative thermal expansion (NTE) performance. In addition, the phase transition temperature (Tc) of Fe₂Mo₃O₁₂ was reduced from 508.1 °C to room temperature with the increase of (KMg)³⁺-substitution. Monoclinic KMgFeMo₃O₁₂ ceramics was observed to show stronger NTE in a wider temperature range of 30–700 °C for the first time. Its corresponding coefficient of thermal expansion (CTE) is as high as ?17.21 × 10^?6 °C^?1. The distortion of [FeO₆/MgO₆] polyhedra in (KMg)_xFe_2-xMo₃O₁₂ caused by (KMg)³⁺-substitution contributed to the stronger NTE.     

Effect of the thermal treatment on microstructure and physical properties of low-density and high transparency silica aerogels via acetonitrile supercritical drying

In this paper, we reported the experimental results about the effect of the thermal treatment on microstructure and physical properties of low-density and high transparent silica aerogels. From our results, with tetramethyl orthosilicate as precursor and via acetonitrile supercritical drying process, silica aerogel monolith was obtained possessing the properties as low-density (0.018 g/cm³), high surface area (923 m²/g), high optical transparency (87.9 %, 800 nm). It should be noted that high transparency of silica aerogel can be maintained up to 600 °C (91.5 %, 800 nm). The mechanical properties of silica aerogel decreased with increasing heat treated temperature to 600 °C, and silica aerogels still maintained crack-free monoliths completely and possessed high homogeneous density even after 600 °C thermal treatment. Furthermore, thermal conductivity of the monoliths at desired temperatures was analyzed by the transient plane heat source method. When the temperature flowed from 25 to 600 °C, thermal conductivity coefficients of silica aerogels changed from 0.021 to 0.065 W (m K)^?1, revealed an excellent heat insulation effect in high-temperature area. Currently, the specific process developed for low-density aerogels affected by thermal treatment has not been reported in previous literature.     

Optimization of Alumina and Aluminosilicate Aerogel Structure for High-Temperature Performance

Alumina and aluminosilicate aerogels offer potential for use at temperatures above 700°C, where silica aerogels begin to sinter. Stability of alumina and aluminosilicate pore structures at high temperatures is governed by the starting aerogel structure, which, in turn is controlled by the synthesis route. Structure, morphology, and crystallization behavior are compared for aerogels synthesized from AlCl₃ and propylene oxide with those synthesized from a variety of boehmite precursors. The aerogels possessing a crystalline boehmite structure in the as-synthesized condition retained mesoporous structures to temperatures of 1200°C, while the AlCl₃-derived aerogels, although exhibiting higher as-synthesized surface areas, crystallized and densified at 980–1005°C.     

Novel silica-modified boehmite aerogels and fiber-reinforced insulation composites with ultra-high thermal stability and low thermal conductivity

Alumina–silica composite aerogels have drawn vast attention due to their enhanced thermal stability compared to pristine alumina aerogels. However, they are generally weakly-crystallized and tend to experience inevitable sintering and significant surface area loss especially above 1200 °C. In this study, we developed a hydrothermal treatment and supercritical drying strategy for synthesizing novel, well-crystallized, silica-modified boehmite aerogels and fiber-reinforced composites. For the prepared aerogel, network coarsening was significantly hindered and the α-Al₂O₃ transition was completely prevented even at 1400 °C. As a result, the aerogel exhibits extremely high surface area maintenance (87 % and 53 % after 1300 °C and 1400 °C calcination, respectively) and low linear shrinkage (14 % after 1300 °C calcination) at elevated temperatures. The composite with good toughness shows excellent heat resistance and thermal insulating performance up to 1500 °C. These findings provide a general, direct new idea to improve the thermal tolerance of alumina-based aerogels and extend their applications to higher temperatures.     

Solubility of potassium ferrate in 12 M alkaline solutions between 20°C and 60°C

The solubility of potassium ferrate (K₂FeO₄) was measured in aqueous solutions of NaOH and KOH of total concentration 12 M containing various molar ratios of KOH:NaOH in the range 12:0 to 3:9. Several analytical methods were tested for the determination of ferrate concentration. The final method chosen consisted of potentiometric titration of the ferrate sample with an alkaline solution of As₂O₃. The assumption was made that ferrate dissociates in concentrated KOH solutions predominantly to KFeO₄⁻. The solubility constant, S, defined as the product of the molar concentration of the potassium ion, K⁺, and the ferrate anion, KFeO₄⁻, was found to be 0·044 ± 0·006 mol² dm⁻⁶ for 20°C, 0·093 ± 0·004 mol² dm⁻⁶ for 40°C and 0·15 ± 0·09 mol² dm⁻⁶ for 60°C. From these results the heat of dissolution of K₂FeO₄ was calculated as −14·3 kJ mol⁻¹. At 60°C the enhanced decomposition of the ferrate at the higher temperature led to a greater deviation in solubility values compared with data for either 20°C or 40°C.     

Enhanced insulation and piezoelectric properties of 0.57(Bi0.8La0.2)FeO3-0.43PbTiO3 solid solutions with Fe addition

0.57(Bi_0.8La_0.2)FeO₃-0.43PbTiO₃-x mol%Fe₂O₃ ceramics (BLF-PT-xFe, x = 0, 0.025, 0.05, 0.125, and 0.25) were prepared by the conventional solid-state reaction method. X-ray diffraction (XRD) reveals that all samples display the perovskite structure with a coexistence of tetragonal (T) phase and rhombohedral (R) phase, while the incorporation of Fe promotes the phase transition from T to R. Scanning electron microscopy (SEM) images show that all samples are well crystallized and their grain size increases noticeably with the increase of Fe content. X-ray photoelectron spectroscopy (XPS) results indicate that Fe doping significantly inhibits the formation of oxygen vacancies, thereby improving insulation of BLF-PT-xFe ceramics. Interestingly, the Curie temperature of BLF-PT-xFe is around 330°C, little changing with the variation of Fe content. However, the depolarization temperatures of BLF-PT ceramics with Fe are 50°C higher than that of the sample without Fe doping. The hopping of second ionized oxygen vacancies are the major carriers in the temperature range of 200°C–500°C. The optimal component of BLF-PT-xFe ceramics appear at x = 0.05, where the dielectric loss tanδ, AC resistivity (200°C), and piezoelectric coefficient d₃₃ could be 0.015, 7 × 10⁶ Ω cm, and 245 pC/N, respectively. All these results indicate that the Fe addition is an effective method to enhance dielectric and piezoelectric properties.     

Structural and ferroelectric properties of hafnium substituted BiFeO3 multiferroics synthesized via auto combustion technique

A series of BiFe_1-xHf_(3/4)xO₃ ( 0%, 5%, 10%, 15% and 20%) nanoparticles were synthesized by simple auto combustion technique using citric acid as a fuel. Thermogravimetric (TGA), differential thermogravimetric (DTA), structural, magnetic, dielectric and ferroelectric analyses were investigated. Thermogravimetric analysis provides information of temperature at which phase develops (600?°C). DTA predicts ferroelectric to paraelectric transformation temperature which is found to be 822?°C. X-ray diffraction (XRD) results confirm formation of distorted rhombohedral structure for all compositions along with few traces of Bi₂₅FeO₄₀. The tolerance factor is increased from 0.845 to 0.853 due to larger ionic radius of Hf⁴⁺ substitution on Fe site. Crystallite size (D) is found in the range of 24.2–30.48?nm. Saturation magnetization (Ms) is increased to 16 times and remanent magnetization (Mr) is increased to 8 times than that of pure BiFeO₃. This increment in magnetic parameters is due to reduction of oxygen vacancies, small crystalline size (less than 62?nm), structural distortion and unbalancing condition for antiferromagnetic magnetic moments of Fe³⁺ ions. Dielectric parameters depict decrement behavior with increasing of applied field up to 3?GHz. For Fe_1-xHf_(3/4)xO₃, lower value of dielectric permittivity for all compositions is due to reduction of polarization and less growth of grains but more growth of grain boundaries because of mismatching of Hf and Fe³⁺ ions. P-E hysteresis loop changes from round shape to elliptical shape and it confirms less lossy nature of ferroelectric loops. Higher values of Ms as well as Mr but lower values of dielectric constant as well as remanent polarization for these nanoparticles make them useful for MeRAM (magnetoelectric random access memory) and high resonant applications.     

Porosity of Mixed Iron Oxide-Chromia Alumina Aerogels

Mixed iron oxide-chromia-alumina aerogels were prepared by mixing a solution of iron and chromium acetylacetonates in methyl alcohol with a solution of aluminum tri-sec-butoxide in 2-butanol followed by hydrolysis and supercritical drying. The resultant aerogels were highly porous, weak monoliths that easily broke into fine porous particles. Addition of 8% Fe or 2% Cr to the aluminum precursor solution increased the surface area of the resultant alumina aerogel from 400 m²/g to 500 and 600 m²/g respectively. These materials have significant pore volume as judged by the amount of N₂ adsorbed at liquid nitrogen temperatures (range of 400 to 1,100 cm³ N₂/g at P/P₀ = 0.9). Post treatments of oxidation or reduction also increased the porosity of the aerogels to values as high as 2,500 cm³ N₂/g. It then appears that small percentages of foreign cations (Fe, Cr) can increase significantly the porosity of a material like an alumina aerogel.     

Structures and electrical conductivities of Gd3+ and Fe3+ co-doped cerium oxide electrolytes sintered at low temperature for ILT-SOFCs

Gd³⁺ and Fe³⁺ co-doped cerium oxide electrolytes, Ce_0.9Gd_0.1‐xFe_xO_2-δ (x?=?0.00, 0.01, 0.03, 0.05, 0.07, 0.10), were prepared by co-precipitation for ultrafine precursor powders and sintering for densified ceramic pellets. The crystal and microscopic structures were characterized by XRD, FESEM and Raman spectroscopy and their electrical properties were studied by AC impedance spectroscopy and the measurement of single cell's outputs. In comparison with Ce_0.9Gd_0.1O_1.95, the ceramic pellets of Ce_0.9Gd_0.1‐xFe_xO_2-δ with a relative density of 95% can be obtained after sintered at 1000?°C for 5?h, showing a remarkably enhanced sintering performance with a sintering temperature reduction of 500?°C, which might be ascribed to the highly activated migration of constituent species in the cerium oxide lattice doped with Gd³⁺ and Fe³⁺ions. Moreover, the electrical conductivity of Ce_0.9Gd_0.1‐xFe_xO_2-δ can be significantly enhanced depending on the mole fraction x, with Ce_0.9Gd_0.07Fe_0.03O_1.95 exhibiting the highest electrical conductivity of 38 mS/cm at 800?°C, about 36% higher than that of Ce_0.9Gd_0.1O_1.95 electrolyte sintered at 1500?°C for 5?h. So, The Gd³⁺ and Fe³⁺ co-doped cerium oxide would be an excellent candidate electrolyte for ILT SOFCs due to its prominent sintering performance and enhanced electrical conductivity.     

Phase characterization of iron/manganese fischer-tropsch catalysts: effect of compositon and reduction conditions

The bulk phases of Fe-Mn catalysts after calcination, reduction and synthesis were investigated by Mo˝ssbauer spectroscopy. After calcination at 500°, the iron rich material exists as a single phase solid solution —(Fe_l-_xMn_x)₂0₃ whereas the Mn-rich material is a mixture of —(Fe₁-_xMn_x)₂0₃ and —(Mn₁-_yFe_y)₂0₃. Consequently,the Mn-rich catalyst ends up as an inhomogeneous conglomerate oT five phases after synthesis. The oxides at all stages of reduction and synthesis have Mn and Fe interdissolved, but the metal carbides have no detectable Mn-alloying. The phase composition after 200 h of Fischer-Tropsch synthesis depends on the reduction temperature. Reduction temperature of 400° leads to complete reduction and to large amounts of carbide and small amounts of spinel after synthesis. Further, the carbide is mainly χ-Fe₅C₂ and small amounts of O(œ')-Fe₂C. These trends reverse when the reduction is carried out at 300°.