Indoor air pollution from particulate matter emissions in different households in rural areas of Bangladesh

Indoor air pollution from the combustion of traditional biomass fuels (wood, cow dung, and crop wastes) is a significant public health problem predominantly for poor populations in many developing countries. It is particularly problematic for the women who are normally responsible for food preparation and cooking, and for infants/young children who spend time around their mothers near the cooking area. Airborne particulate matter (PM) samples were collected from cooking and living areas in homes in a rural area of Bangladesh to investigate the impact of fuel use, kitchen configurations, and ventilation on indoor air quality and to apportion the source contributions of the measured trace metals and BC concentrations. Lower PM concentrations were observed when liquefied petroleum gas (LPG) was used for cooking. PM concentrations varied significantly depending on the position of kitchen, fuel use and ventilation rates. From reconstructed mass (RCM) calculations, it was found that the major constituent of the PM was carbonaceous matter. Soil and smoke were identified as components from elemental composition data. It was also found that some kitchen configurations have lower PM concentrations than others even with the use of low-grade biomass fuels. Adoption of these kitchen configurations would be a cost-effective approach in reducing exposures from cooking in these rural areas.     

Spatial heterogeneity of personal exposure to airborne metals in French urban areas

The spatial distribution of urban population exposures to ambient air particles was investigated as part of the Genotox'ER study conducted in four metropolitan areas (Grenoble, Paris, Rouen and Strasbourg) in France. In each city, 60 to 90 non-smoking adult and children volunteers were selected. Subjects lived in three different urban sectors: one highly exposed to traffic emissions, one influenced by local industrial sources, and a background urban environment. The Harvard Chempass multi-pollutant personal sampler was used to sample PM10 and PM2.5 particles during 48 h during two different seasons ('hot' and 'cold'). The elemental composition of the filters was analysed by Particle-Induced X-ray Emission (PIXE). Sixteen elements were found to be over the method detection limits: Al, Si, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn and Pb. The relative concentrations of elements of crustal origin (Si, Al, Ca) were higher in the coarse fraction of PM10 filters, while elements associated with combustion processes (traffic emissions or industrial combustion) presented higher relative concentrations in the PM2.5 fraction (S, Ni, V, Pb). Spatial heterogeneity of elemental exposures by urban sector is substantial for some metals of health concern, with 20% to 90% greater exposure values, on average, in the traffic proximity or industrial sectors, compared to the background sector, for Fe, Zn, Cu, V and Cr. This spatial heterogeneity should not be overlooked in epidemiological or risk assessment studies.     

Variations in vanadium, nickel and lanthanoid element concentrations in urban air

The emission of trace metal pollutants by industry and transport takes place on a scale large enough to alter atmospheric chemistry and results in measurable differences between the urban background of inhalable particulate matter (PM) in different towns. This is particularly well demonstrated by the technogenic release into the atmosphere of V, Ni, and lanthanoid elements. We compare PM concentrations of these metals in large datasets from five industrial towns in Spain variously influenced by emissions from refinery, power station, shipping, stainless steel, ceramic tiles and brick-making. Increased La/Ce values in urban background inhalable PM, due to La-contamination from refineries and their residual products (fuel oils and petcoke), contrast with Ce-rich emissions from the ceramic related industry, and clearly demonstrate the value of this ratio as a sensitive and reliable tracer for many point source emissions. Similarly, anomalously high V/Ni values (> 4) can detect the influence of nearby high-V petcoke and fuel oil combustion, although the use of this ratio in urban background PM is limited by overlapping values in natural and anthropogenic materials. Geochemical characterisation of urban background PM is a valuable compliment to the physical monitoring of aerosols widely employed in urban areas, especially given the relevance of trace metal inhalation to urban health issues.     

Aerosol advection and sea salt events in Genoa, Italy, during the second half of 2005

Atmospheric aerosols in the PM(10) fraction have been simultaneously sampled at three sites in the Genoa urban and suburban area during the second half of 2005, and information on the elemental composition has been gathered through energy dispersive X-ray fluorescence. Thanks to the simultaneous measurements and wind information, a few aerosol transport and transformation processes originated from the nearby sea and in the neighbouring Po Valley have been described. Sea salt concentrations at the three sites were well correlated and often related to Southern sector winds; moreover, by examining the Cl/Na ratio at two sites the time scale for Cl depletion in particulate matter has been estimated as 1-1.5 h for the Genoa atmosphere. During a Northerly gale, excess elemental Si concentrations (peaking more than 4 mug m(-3)) were found at two sites, and were ascribed to an unknown local source. Finally, during an 11-day long 'heat wave' large concentrations for total PM(10), dust and secondary compounds have been found; these large concentrations lead to a number of exceedances of air quality standards, and have been ascribed to advection from the Po Valley.     

Characterization of indoor air quality in primary schools in Antwerp, Belgium

The indoor air quality of 27 primary schools located in the city centre and suburbs of Antwerp, Belgium, was assessed. The primary aim was to obtain correlations between the various pollutant levels. Indoor:outdoor ratios and the building and classroom characteristics of each school were investigated. This paper presents results on indoor and local outdoor PM2.5 mass concentrations, its elemental composition in terms of K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Br, Pb, Al, Si, S, and Cl, and its black smoke content. In addition, indoor and local outdoor levels of the gases NO2, SO2, O3, and BTEX (benzene, toluene, ethyl benzene, and xylene isomers) were determined. Black smoke, NO2, SO2 and O3, occurred at indoor:outdoor ratios below unity, indicating their significant outdoor sources. No linear correlation was established between indoor and outdoor levels for PM2.5 mass concentrations and BTEX; their indoor:outdoor ratios exceeded unity except for benzene. Classroom PM2.5 occurred with a different elemental composition than local outdoor PM2.5. The re-suspension of dust because of room occupation is probably the main contributor for the I/O ratios higher than 1 reported for elements typically constituting dust particles. Finally, increased benzene concentrations were reported for classrooms located at the lower levels. PRACTICAL IMPLICATIONS: The elevated indoor PM2.5, and BTEX concentrations in primary school classrooms, exceeding the ambient concentrations, raise concerns about possible adverse health effects on susceptible children. This is aggravated by the presence of carpets and in the case of classrooms at lower levels. Analysis of PM2.5's elemental composition indicated a considerable contribution of soil dust to indoor PM2.5 mass. In order to set adequate threshold values and guidelines, detailed information on the health impact of specific PM2.5 composites is needed. The results suggest that local outdoor air concentrations measurements do not provide an accurate estimation of children's personal exposures to the identified air pollutants inside classrooms.     

Particulate exposure and size distribution from wood burning stoves in Costa Rica

Biomass fuel is the most common energy source for cooking and space heating in developing countries. Biomass fuel combustion causes high levels of indoor air pollutants including particulates and other combustion by-products. We measured indoor air quality in 23 houses with a wood burning stove in rural residential areas of Costa Rica. Daily PM2.5, PM10 and CO concentrations, and particle size distribution were simultaneously measured in the kitchen. When a wood burning stove was used during the monitoring period, average daily PM2.5 and PM10 concentrations were 44 and 132 microg/m3, respectively. Average CO concentrations were between 0.5 and 3.3 ppm. All houses had a particle size distribution of either one or two peaks at around 0.7 and 2.5 microm aerodynamic diameters. The particulate levels increased rapidly during cooking and decreased quickly after cooking. The maximum peak particulate levels ranged from 310 to 8170 microg/m3 for PM2.5 and from 500 to 18900 microg/m3 for PM10 in all houses. Although the 24-h particulate levels in this study are lower than the National Ambient Air Quality Standards of PM2.5 and PM10, it is important to note that people, especially women and children, are exposed to extremely high levels of particulates during cooking.     

Results of a residential indoor PM2.5 sampling program before and after a woodstove changeout

During 2005-2007, a woodstove changeout program was conducted in a Rocky Mountain valley community in an effort to reduce ambient levels of PM(2.5). In addition to changes in ambient PM(2.5), an opportunity was provided to evaluate the changes in indoor air quality when old stoves were replaced with US Environmental Protection Agency (EPA)-certified woodstoves. PM(2.5) samples were measured in 16 homes prior to and following the changeout. For each sampling event, PM(2.5) mass was continuously measured throughout the 24-h sampling periods, and organic/elemental carbon (OC/EC) and associated chemical markers of woodsmoke were measured from quartz filters. Results showed that average PM(2.5) concentrations and maximum PM(2.5) concentrations were reduced by 71% and 76%, respectively (as measured by TSI DustTraks). Levoglucosan was reduced by 45% following the introduction of the new woodstove. However, the concentrations of resin acids, natural chemicals found in the bark of wood, were increased following the introduction of the new woodstove. There were no discernible trends in methoxphenol levels, likely due to the semi-volatile nature of the species that were measured. Although there is some uncertainty in this study regarding the amount of ambient PM infiltration to the indoor environment, these findings demonstrated a large impact on indoor air quality following this intervention. PRACTICAL IMPLICATIONS: Emissions from residential woodstoves are an important air quality issue (both indoors and ambient) in many regions throughout the US and the world. More specifically, woodstoves have been identified as a major source of PM(2.5) in valley locations throughout the Northern Rocky Mountains, where biomass combustion is the predominant source of home heating. In this study, we present results that demonstrate the dramatic reduction in PM(2.5) concentrations (as measured by TSI, Inc. DustTrak PM(2.5) air samplers) inside homes following the replacement of old, polluting woodstove with new EPA-certified woodstoves.     

Elemental composition and sources of fine and ultrafine ambient particles in Erfurt,Germany

We present the first results of a source apportionment for the urban aerosol in Erfurt, Germany, for the period 1995-1998. The analysis is based on data of particle number concentrations (0.01-2.5 microm; mean 1.8 x 10(4) cm(-3), continuous), the concentration of the ambient gases SO(2), NO, NO(2) and CO (continuous), particle mass less than 2.5 microm (PM(2.5)) and less than 10 microm (PM(10)) (Harvard Impactor sampling, mean PM(2.5) 26.3 micro/m(3), mean PM(10) 38.2 microg/m(3)) and the size fractionated concentrations of 19 elements (impactor sampling 0.05-1.62 microm, PIXE analysis). We determined: (a) the correlations between (i) the 1- and 24-h average concentrations of the gaseous pollutants and the particle number as well as the particle mass concentration and (ii) between the 24-h elemental concentrations; (b) Crustal Enrichment Factors for the PIXE elements using Si as reference element; and (c) the diurnal pattern of the measured pollutants on weekdays and on weekends. The highly correlated PIXE elements Si, Al, Ti and Ca having low enrichment factors were identified as soil elements. The strong correlation of particle number concentrations with NO, which is considered to be typically emitted by traffic, and the striking similarity of their diurnal variation suggest that a sizable fraction of the particle number concentration is associated with emission from vehicles. Besides NO and particle number concentrations other pollutants such as NO(2), CO as well as the elements Zn and Cu were strongly correlated and appear to reflect motor vehicle traffic. Sulfur could be a tracer for coal combustion, however, it was not correlated with any of the quoted elements. Highly correlated elements V and Ni have similar enrichment factors and are considered as tracers for oil combustion.     

Influence of residential wood combustion on local air quality

The importance of wood combustion to local air quality was estimated by measuring different air pollutants and conducting chemical mass balance modelling. PM10, PM2.5, PAHs and VOC concentrations in ambient air were measured in a typical Finnish residential area. Measurements were conducted in January-March 2006. For some compounds, wood combustion was clearly the main local source at this site. The effect of wood combustion was more clearly seen for organic compounds than for fine particle mass. For fine particles, background concentrations dominated. However, very high, short-lived concentration peaks were detected, when the wind direction and other weather conditions were favourable. For organic compounds, the effect of wood combustion was seen in diurnal and in two-week average concentrations. PAH-concentrations were often several times higher at the residential area than in the background. Benzene concentrations showed similar diurnal pattern as the use of wood and benzene/toluene ratios indicated that wood combustion is the most important source. A chemical mass balance model was used for studying the effect of wood combustion on the measured concentrations of VOCs. Model results showed that the main local sources for VOCs at Kurkim?ki are wood combustion and traffic. Wood combustion was clearly the most important source for many compounds (e.g., benzene).     

Elemental composition of tropospheric aerosols in Hanoi, Vietnam and Nairobi, Kenya

Air pollution problems in major cities within the developing countries need to be studied. There are scanty measurements from the developing countries on airborne particles despite their adverse implications to human health, visibility and climate. One of the major sources of anthropogenic air pollution is energy production. Energy demand is bound to increase as population increases, especially in major cities of the world. Fine particles, particles with aerodynamic diameter < or = 2.5 microm, are mainly anthropogenic and these particles were collected in the capital cities of Vietnam and Kenya. A cyclone airborne particle collector was used to sample in Hanoi during the months of May to October 2000 and a dichotomous virtual impactor in Nairobi in February 2000. The samples were analysed for elemental content by an energy dispersive X-ray fluorescence (EDXRF) spectrometer. S, Cl, K and Fe exceeded atmospheric concentrations of 100 ng m(-3) at both cities. Atmospheric elemental concentrations in both Hanoi and Nairobi were orders of magnitude higher than their respective rural towns. Traffic, biomass and waste burning emissions were implicated as the main sources of air pollution in Nairobi, while coal combustion and road transport were the major sources in Hanoi. Regional air pollution had a major impact over Hanoi, whereas an influence of that kind was not identified in Nairobi. Pb and other toxic elements had concentration levels below WHO guideline, however, the two cities are threatened by future high levels of air pollution due to the high rate of population growth. Long-term measurements are required in both areas to evaluate if the alarming situation is deteriorating.     

Particulate matter concentrations in residences: an intervention study evaluating stand-alone filters and air conditioners

This study, a randomized controlled trial, evaluated the effectiveness of free-standing air filters and window air conditioners (ACs) in 126 low-income households of children with asthma. Households were randomized into a control group, a group receiving a free-standing HEPA filter placed in the child's sleeping area, and a group receiving the filter and a window-mounted AC. Indoor air quality (IAQ) was monitored for week-long periods over three to four seasons. High concentrations of particulate matter (PM) and carbon dioxide were frequently seen. When IAQ was monitored, filters reduced PM levels in the child's bedroom by an average of 50%. Filter use varied greatly among households and declined over time, for example, during weeks when pollutants were monitored, filter use was initially high, averaging 84±27%, but dropped to 63±33% in subsequent seasons. In months when households were not visited, use averaged only 34±30%. Filter effectiveness did not vary in homes with central or room ACs. The study shows that measurements over multiple seasons are needed to characterize air quality and filter performance. The effectiveness of interventions using free-standing air filters depends on occupant behavior, and strategies to ensure filter use should be an integral part of interventions. PRACTICAL IMPLICATIONS: Environmental tobacco smoke (ETS) increased particulate matter (PM) levels by about 14 μg/m3 and was often detected using ETS-specific tracers despite restrictions on smoking in the house as reported on questionnaires administered to caregivers. PM concentrations depended on season, filter usage, relative humidity, air exchange ratios, number of children, outdoor PM levels, sweeping/dusting, and presence of a central air conditioner (AC). Free-standing air filters can be an effective intervention that provides substantial reductions in PM concentrations if the filters are used. However, filter use was variable across the study population and declined over the study duration, and thus strategies are needed to encourage and maintain use of filters. The variability in filter use suggests that exposure misclassification is a potential problem in intervention studies using filters. The installation of a room AC in the bedroom, intended to limit air exchange ratios, along with an air filter, did not lower PM levels more than the filter alone.     

Indoor/outdoor relationships for PM2.5 and associated carbonaceous pollutants at residential homes in Hong Kong - case study

Six residences were selected (two roadside, two urban, and two rural) to evaluate the indoor-outdoor characteristics of PM(2.5) (aerodynamic diameter <2.5 microm) carbonaceous species in Hong Kong during March and April 2004. Twenty-minute-averaged indoor and outdoor PM(2.5) concentrations were recorded by DustTrak samplers simultaneously at each site for 3 days to examine diurnal variability of PM(2.5) mass concentrations and their indoor-to-outdoor (I/O) ratios. Daily (24-h average) indoor/outdoor PM(2.5) samples were collected on pre-fired quartz-fiber filters with battery-powered portable mini-volume samplers and analyzed for organic and elemental carbon (OC, EC) by thermal/optical reflectance (TOR) following the Interagency Monitoring of Protected Visual Environments (IMPROVE) protocol. The average indoor and outdoor concentrations of 24 h PM(2.5) were 56.7 and 43.8 microg/m(3), respectively. The short-term PM(2.5) profiles indicated that the penetration of outdoor particles was an important contributor to indoor PM(2.5), and a household survey indicated that daily activities were also sources of episodic peaks in indoor PM(2.5). The average indoor OC and EC concentrations of 17.1 and 2.8 microg/m(3), respectively, accounted for an average of 29.5 and 5.2%, respectively, of indoor PM(2.5) mass. The average indoor OC/EC ratios were 5.8, 9.1, and 5.0 in roadside, urban, and rural areas, respectively; while average outdoor OC/EC ratios were 4.0, 4.3, and 4.0, respectively. The average I/O ratios of 24 h PM(2.5), OC, and EC were 1.4, 1.8, and 1.2, respectively. High indoor-outdoor correlations (r(2)) were found for PM(2.5) EC (0.96) and mass (0.81), and low correlations were found for OC (0.55), indicative of different organic carbon sources indoors. A simple model implied that about two-thirds of carbonaceous particles in indoor air are originated from outdoor sources. PRACTICAL IMPLICATIONS: Indoor particulate pollution has received more attentions in Asia. This study presents a case study regarding the fine particulate matter and its carbonaceous compositions at six residential homes in Hong Kong. The characteristics and relationship of atmospheric organic and elemental carbon were discussed indoors and outdoors. The distribution of eight carbon fractions was first reported in indoor samples to interpret potential sources of indoor carbonaceous particles. The data set can provide significant scientific basis for indoor air quality and epidemiology study in Hong Kong and China.     

Chemical composition, mass size distribution and source analysis of long-range transported wildfire smokes in Helsinki

Special episodes of long-range transported particulate (PM) air pollution were investigated in a one-month field campaign at an urban background site in Helsinki, Finland. A total of nine size-segregated PM samplings of 3- or 4-day duration were made between August 23 and September 23, 2002. During this warm and unusually dry period there were two (labelled P2 and P5) sampling periods when the PM2.5 mass concentration increased remarkably. According to the hourly-measured PM data and backward air mass trajectories, P2 (Aug 23-26) represented a single, 64-h episode of long-range transported aerosol, whereas P5 (Sept 5-9) was a mixture of two 16- and 14-h episodes and usual seasonal air quality. The large chemical data set, based on analyses made by ion chromatography, inductively coupled plasma mass spectrometry, X-ray fluorescence analysis and smoke stain reflectometry, demonstrated that the PM2.5 mass concentrations of biomass signatures (i.e. levoglucosan, oxalate and potassium) and of some other compounds associated with biomass combustion (succinate and malonate) increased remarkably in P2. Crustal elements (Fe, Al, Ca and Si) and unidentified matter, presumably consisting to a large extent of organic material, were also increased in P2. The PM2.5 composition in P5 was different from that in P2, as the inorganic secondary aerosols (NO3-, SO4(2-), NH4+) and many metals reached their highest concentration in this period. The water-soluble fraction of potassium, lead and manganese increased in both P2 and P5. Mass size distributions (0.035-10 microm) showed that a large accumulation mode mainly caused the episodically increased PM2.5 concentrations. An interesting observation was that the episodes had no obvious impact on the Aitken mode. Finally, the strongly increased concentrations of biomass signatures in accumulation mode proved that the episode in P2 was due to long-range transported biomass combustion aerosol.     

Intense winter atmospheric pollution episodes affecting the Western Mediterranean

The geographic location of the Western Mediterranean Basin and its peculiar topography, the climatic conditions and the intense anthropogenic and natural emissions of atmospheric pollutants are key factors necessary to interpret the atmospheric aerosol phenomenology over this area. During the cold season it is common to have severe atmospheric particulate matter (PM) pollution episodes (of an anthropogenic origin) affecting this region, not only in the urban and industrial areas but also in the regional and rural sites. During these episodes, the midday hourly PM₁ levels at regional background sites are in many cases higher than those at urban areas. Around 10% of the days under winter anticyclonic conditions registered similar PM₁ levels at the regional background than at the urban area and, sporadically the daily PM₁ levels at the regional background sites may exceed those at urban sites. Furthermore, the very high hourly PM₁ levels measured at regional background sites during these episodes are not regularly attained in the closest urban areas, which leads to the hypothesis that an important formation of secondary aerosols occurs during the transport of the polluted air masses towards the elevated rural sites.The interpretation of the variability of PM levels and composition (2002-2008) at one urban site (Barcelona) and at one regional background site (Montseny) allows us to illustrate the phenomenology of these scenarios, to quantify the mean annual contributions to the PM levels and to identify their main tracers. Ammonium nitrate appears to be the most abundant compound during these scenarios, although organic species and trace metals also increase markedly. Owing to the intensity, composition and recurrence of these atmospheric pollution episodes, important health, climatic and ecological implications may be derived.     

Characteristics of emissions of air pollutants from burning of incense in temples, Hong Kong

Field investigations of target air pollutants at two of the most famous temples in Hong Kong were conducted. The air pollution problems in these two temples during peak and non-peak periods were characterized. The target air pollutants included particulate matters (PM(10), PM(2.5)), volatile organic compounds (VOCs), carbonyl compounds, carbon monoxide (CO), nitrogen oxides (NO(x)), methane (CH(4)), non-methane hydrocarbons (NMHC), organic carbon (OC), elemental carbon (EC), and inorganic ions (Cl(-), NO(3)(-), SO(4)(2-), Na(+), NH(4)(+), and K(+)). The pollutant levels of the two temples during peak period were shown to be significantly higher than those during non-peak period. The highest average CO level was obtained at Temple 1 during peak period, which exceeded IAQO 8-h Good Class criteria. In general, the average PM(2.5)/PM(10) ratios were approximately 82%. The results revealed that the fine particulates (PM(2.5)) constituted the majority of suspended particulates at both temples. It was noted that formaldehyde was the most abundant carbonyl compounds, followed by acetaldehyde. At Temple 1 during peak period, the average benzene concentration exceeded almost 8 times more than Indoor Air Quality Objectives for Office Buildings and Public Places (IAQO) [HKEPD, 2003. Guidance notes for the management of indoor air quality in offices and public places. Indoor air quality management group, The Government of the Hong Kong Special Administrative Region.] Good Class criteria. The average OC/EC ratios ranged from 2.6 to 17 in PM(10) and from 4.2 to 18 in PM(2.5) at two temples, which suggested that OC measured in these two temple areas may be due to both direct emission from incense burning and secondary formation by chemical reactions. The total mass of inorganic ions, organic carbon, and elemental carbon accounted for about 71% in PM(2.5) and 72% in PM(10).     

Elemental and organic carbon in aerosols over urbanized coastal region (southern Baltic Sea, Gdynia)

Studies on PM 10, total particulate matter (TSP), elemental carbon (EC) and organic carbon (OC) concentrations were carried out in the Polish coastal zone of the Baltic Sea, in urbanized Gdynia. The interaction between the land, the air and the sea was clearly observed. The highest concentrations of PM 10, TSP and both carbon fractions were noted in the air masses moving from southern and western Poland and Europe. The EC was generally of primary origin and its contribution to TSP and PM 10 mass was on average 2.3% and 3.7% respectively. Under low wind speed conditions local sources (traffic and industry) influenced increases in elemental carbon and PM 10 concentrations in Gdynia. Elemental carbon demonstrated a pronounced weekly cycle, yielding minimum values at the weekend and maximum values on Thursdays. The role of harbors and ship yards in creating high EC concentrations was clearly observed. Concentration of organic carbon was ten times higher than that of elemental carbon, and the average OC contribution to PM 10 mass was very high (31.6%). An inverse situation was observed when air masses were transported from over the Atlantic Ocean, the North Sea and the Baltic Sea. These clean air masses were characterized by the lowest concentrations of all analysed compounds.Obtained results for organic and elemental carbon fluxes showed that atmospheric aerosols can be treated, along with water run-off, as a carbon source for the coastal waters of the Baltic Sea. The enrichment of surface water was more effective in the case of organic carbon (0.27 ± 0.19 mmol m⁻² d⁻¹). Elemental carbon fluxes were one order of magnitude smaller, on average 0.03 ± 0.04 mmol m⁻² d⁻¹. We suggest that in some situations atmospheric carbon input can explain up to 18% of total carbon fluxes into the Baltic coastal waters.     

Aerosol chemical composition over Istanbul

This study examines the chemical composition of aerosols over the Greater Istanbul Area. To achieve this 325 (PM₁₀) aerosol samples were collected over Bosphorus from November 2007 to June 2009 and were analysed for the main ions, trace metals, water-soluble organic carbon (WSOC), organic (OC) and elemental carbon (EC).PM₁₀ levels were found to be in good agreement with those measured by the Istanbul Municipality air quality network, indicating that the sampling site is representative of the Greater Istanbul Area. The main ions measured in the PM₁₀ samples were Na⁺, Ca²⁺ and non-sea-salt sulphates (nss-SO₄²⁻). On average, 31% of Ca²⁺ was found to be associated with carbonates. Trace elements related to human activities (as Pb, V, Cd and Ni) obtained peak values during winter due to domestic heating, whereas natural origin elements like Al, Fe and Mn peaked during the spring period due to dust transport from Northern Africa. Organic carbon was found to be mostly primary and elemental carbon was strongly linked to fuel oil combustion and traffic. Both OC and EC concentrations increased during winter due to domestic heating, while the higher WSOC to OC ratio during summer can be mostly attributed to the presence of secondary, oxidised and more soluble organics. Factor analysis identified six components/sources for aerosol species in PM₁₀, namely traffic/industrial, crustal, sea-salt, fuel-oil combustion, secondary and ammonium sulfate.     

Roadside PM10 and associated metals in Constantine,Algeria

Samples of particulate matter less than or equal to 10 μm (PM10) were collected every other day using an Airmetrics MiniVol portable air sampler in Constantine, the third largest and most densely populated city of Algeria with a population of 600,000. The main objective of this study was to assess the concentrations of particulate matter (PM) with an aerodynamic diameter ≤10 μm (PM10), and dust-laden trace metals in a residential area with heavy traffic during two months, from 25 March 2010 to 24 May 2010. Furthermore, the present work examines the daily levels of metallic elements Fe, Zn and Cu. The PM10 concentrations ranged from 7.6 to 159.4 μg/m³ during the study period. WHO’s daily PM10 average guide value of 50 μg/m³ was exceeded 10 times over 31 samples. HYSPLIT back trajectories were used to identify the source locations of the pollutants. Rain scavenging of atmospheric particulate matter led to a substantial decrease in PM10 concentrations. During the study period, Zn was detected in one sample at a concentration of 0.78 μg/m³. It is believed that air masses originating from Iceland’s Eyjafjöll volcano may have transported clouds of ashes rich in Zn to the sampling site on that occasion. A maximum of 2.92 μg/m³ of Cu was observed when the volcanic cloud reached the sampling site four times during the corresponding 24-h sampling period.     

The analysis of PM2.5 and associated elements and their indoor/outdoor pollution status in an urban area

In this study, elemental composition of PM2.5 and the status of indoor/outdoor pollution were investigated in a commercial building near a roadside area in Daejeon, Korea. A total of 60 parallel PM2.5 samples were collected both on the roof (outdoor) and in an indoor office of a building near a highly congested road during the spring and fall of 2008. The concentrations of 23 elements were analysed from these PM2.5 samples using instrumental neutron activation analysis. PM2.5 levels in indoor environment (47.6 ± 16.5 μg/m(3)) were noticeably higher than the outdoor levels (37.7 ± 17.2 μg/m(3)) with the I/O concentration ratio of 1.37 ± 0.33 [correlation coefficient (r) = 0.89, P < 0.001]. Principal component analysis results coincidently showed the predominance of sources such as soil dust, traffic, oil/coal combustion and road dust for both indoor and outdoor microenvironments. An isolated source in the indoor environment was assigned to environmental tobacco smoke (ETS) with high factor loading of Ce, Cl, I, K, La and Zn. The overall results of our study indicate that the sources of indoor constituents were strongly dependent on outdoor processes except for the ones affected by independent sources such as ETS. PRACTICAL IMPLICATIONS: An improved understanding of the factors affecting the indoor PM2.5 concentration levels can lead to the development of an efficient management strategy to control health risks from exposure to indoor PM2.5 and related toxic components. A comparison of our comprehensive data sets indicated that most indoor PM2.5 and associated elemental species were strongly enriched by indoor source activities along with infiltration of ambient outdoor air for a naturally ventilated building.     

Optical and chemical characteristics of the atmospheric aerosol in four towns in southern Poland

The absorption coefficient a(p) [m(-1)] as well as the mass absorption coefficient sigma(p) [m(2)/g] has been estimated for PM10 and PM2.5 in four towns located in southern Poland, based on the assumption that the reflectance of aerosol-laden filters is a good proxy for the absorptivity of aerosols. The optical properties of the airborne particles were also compared with their surface composition obtained by photoelectron spectroscopy (XPS). It was found that coarse particles, which constituted 20-30% of PM10, exhibited insignificant contribution to the absorption. The most absorptive aerosols were found in the towns located in Upper Silesia, a highly industrialized area. This reflects both the relative content of carbon in PM2.5 and the mass concentration of the fine mode. It was found that oxides and sulfates play an important role in promoting the reflectance of light from aerosols in the winter. These results support the suggestion that the revision of existing air quality standards for particulate pollution is needed.