The preparation,characterization, and cure reactions of new bisbenzocyclobutene‐terminated aromatic imides

Several new bisbenzocyclobutene‐terminated aromatic imides, 2,2′‐bis(N‐4‐benzocyclobutenyl) phthalimide, 2,2′‐bis[4‐(N‐4‐benzocyclobutenylphthalimide)]‐ether, 2,2′‐bis[4‐(N‐4‐benzocyclobutenylphthalimide)]‐ketone, and 2,2′‐bis[4‐(N‐4‐benzo cyclobutenylphthalimid‐4‐oxy) phenyl]‐propane, have been synthesized in high yields and characterized by FTIR, MS, EA, and ¹H NMR spectroscopy. The polymers cured from benzocyclobutene‐terminated imides have high glass transition temperature and good thermal stabilities. The cure reaction of an imide was studied by FTIR‐ATR (attenuated total reflection) and DSC techniques. Apparent kinetic parameters of the cure reaction are obtained. The apparent cure reaction order, activation energy, and pre‐exponential factor determined by isothermal DSC method are 1, 143.4 kJ/mol, and 3.88× 10¹³ min^?1, and by nonisothermal DSC methods 1, 139.4 kJ/mol, and 2.27× 10¹³ min^?1, respectively. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1705–1719, 2006     

Effect of type of substitution in 4,4′‐bis‐(diaminodiphenyl) methane hardener on cure kinetics,mechanical, and flame retardant properties of tetrafunctional epoxy resins

The nature of the substituent in 4,4′‐bis‐(diaminodiphenyl) methane (DDM) hardener on the cure kinetics, mechanical, and flame retardant properties of N,N,N′,N′‐tetraglycidyl diaminodiphenyl methane (TGDDM) resin is investigated in comparison with unsubstituted DDM and widely used 4,4′‐bis‐(diaminodiphenyl) sulfone hardeners. Dynamic differential scanning calorimetry (DSC) and cure rheology studies showed that the substitution decreased the reactivity of the amine. An electron‐withdrawing chlorine substituent was found to be more effective than an electron‐releasing methyl group in reducing the amine reactivity. Substituted and unsubstituted DDM hardeners showed two peaks in their DSC thermograms that were due to steric hindrance in the former and deficiency of amine in the latter. Substitution showed its effect on the mechanical properties and glass‐transition temperature. The flexural modulus was increased; however, the Izod impact and glass‐transition temperature were decreased in substituted amine systems. The limiting oxygen index results showed higher flame retardancy in the chlorine substituted hardener system compared to other hardener systems that were studied. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 480–491, 2006     

Synthesis and properties of a novel bismaleimide resin containing 1,3,4‐oxadiazole moiety and the blend systems thereof with epoxy resin

A new bismaleimide monomer, 2‐((4‐maleimidophenoxy)methyl)‐5‐(4‐maleimidophenyl)‐1,3,4‐oxadiazole (Mioxd), was designed and synthesized. The chemical structure of the monomer was confirmed by means of Fourier transform infrared (FTIR) spectroscopy, proton nuclear magnetic resonance (¹H NMR) spectroscopy and elemental analysis, and its thermal properties were characterized using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Mioxd as a reactive modifier was blended with epoxy resin based on bisphenol A diglycidyl ether (DGEBA) in weight ratio of 5, 10, and 15%, using 4,4′‐diaminodiphenyl sulfone (DDS) as hardener. The effect of Mioxd addition on the cure behavior and thermal properties of the blend resins was studied by DSC, TGA, and dynamic mechanical analysis (DMA). DSC investigations showed that the main exothermic peak temperature (T_p) of the blend systems did not obviously shift with increasing Mioxd content whereas a new shoulder appeared and gradually grew on the high temperature side of the exothermic peak. The results of DMA measurements exhibited the glassy storage modulus (G') and glass transition temperatures (T_g) increased as the Mioxd content was increased, the cured blends investigated were miscible and no phase separation occurred. Further, the thermal decomposition temperature first decreased and then increased, but the char yield at 600°C increased with an increase in Mioxd content. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Evaluation of isomeric composition of resol‐type phenol formaldehyde matrix resins for silica–phenolic composites and its effect on cure characteristics of the resin

The isomeric composition of several samples of resol‐type phenol formaldehyde resins used for silica–phenolic composites was evaluated by ¹H‐ and ¹³C‐NMR spectroscopy and reverse‐phase HPLC techniques. The variations in the isomeric compositions were attributed to inadvertent variations in the process parameters. A mathematical relation was determined for calculation of free phenol from ¹H‐NMR measurements. The samples were cured at 160°C for 8 h in an inert atmosphere of N₂. The extent of cure in the hardened samples was measured by FTIR analysis. The effect of isomeric composition on the extent of cure was studied. Free phenol and p‐hydroxymethyl phenol, exhibiting a linear correlation, were found to have a pronounced effect on the extent of cure. The cure kinetics were derived by dynamic DSC measurements. Activation energy (E) for curing exhibited a near linear correlation independently with free phenol content and the extent of cure. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2517–2524, 2003     

Miscibility and morphological properties of quaternized polysulfone blends with polystyrene and poly(4‐vinylpyridine)

Quaternized polysulfones were synthesized by the quaternization reaction of chloromethylated polysulfone with different tertiary amines −N,N‐dimethylethylamine (DMEA) and N,N‐dimethyloctylamine (DMOA), respectively. New blends from these quaternized polysulfones (PSF‐DMEA or PSF‐DMOA) with polystyrene (PS) or poly(4‐vinylpyridine) (P4VP) were prepared by the solution casting method. Pure quaternized polysulfones, in N,N‐dimethylformamide (DMF)/methanol (MeOH) and DMF/water solvent/nonsolvent mixtures, and their blends with PS and P4VP, as well, were investigated by shear viscometry and viscoelasticity, atomic force microscopy, differential scanning calorimetry, and surface properties. The results obtained revealed that the blends have good miscibility. Surface morphology is characterized by roughness and nodules formations, depending on the alkyl radical lengths, composition of the polymer mixtures, including specific electron‐donor or electron‐acceptor characteristics of polymers. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

CO2‐Switchable Oil/Water Emulsion for Pipeline Transport of Heavy Oil

By mixing an aqueous solution of tertiary amine, N,N‐dimethylethanolamine (DMEA), with naphthenic acid (RCOOH) derived from heavy oil, a CO₂ switchable zwitterionic surfactant (RCOO^?DMEAH⁺) aqueous system was constructed. The CO₂ switchability of this zwitterionic surfactant was confirmed by visual inspection, pH measurements, and conductivity tests, i.e., the RCOO^?DMEAH⁺ decomposed into RCOOH, DMEAH⁺ and HCO₃^? after bubbling CO₂ through but switched back to its original state by subsequent bubbling N₂ through at 80 °C to remove the CO₂. The interfacial tension tests of heavy oil in DMEA aqueous solutions indicated that the solution containing 0.5 wt% of DMEA and 0.2 wt% of NaCl resulted in the lowest interfacial tension. The O/W emulsion formed when aqueous solutions of DMEA were used to emulsify heavy oil exhibited the best performance when the oil/water volume ratio, DMEA concentration, and NaCl concentration were 65:35, 0.5 and 0.2 wt%, respectively. The feasibility of pipeline transport of the O/W heavy oil emulsion was evaluated. The results illustrated that the demulsification of the O/W emulsion after transport could be easily realized by bubbling CO₂ through. Although demulsification efficiency still needs to be improved, the recycling of the aqueous phase after demulsification by removal of CO₂ looks promising.     

Curing kinetics and thermal property characterization of the bisphenol‐F epoxy resin and phthalic anhydride system

The curing kinetics of bisphenol‐F epoxy resin (BPFER) and curing agent phthalic anhydride, with N,N‐dimethylbenzylamine as an accelerator, were studied by differential scanning calorimetry (DSC). Analysis of DSC data indicated autocatalytic behaviour in the first stages of the cure for the system, and that this, could be well described by the model proposed by Kamal, which includes two rate constants, k₁ and k₂, and two reaction orders, m and n. The curing reaction in the later stages was practically diffusion‐controlled. To consider the diffusion effect more precisely, a diffusion factor, ??(α), was introduced into Kamal's equation. The glass transition temperatures (T_gs) of the BPFER/phthalic anhydride samples were determined by means of torsional braid analysis. The thermal degradation kinetics of cured BPFER were investigated by thermogravimetric analysis. © 2002 Society of Chemical Industry     

ToF‐SIMS investigation of epoxy resin curing reaction at different resin to hardener ratios

Time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) and principal components analysis (PCA) were used to analyze diglycidyl ether of bisphenol A (DGEBA) and diglycidyl ether of bisphenol F (DGEBF) epoxy resin blend cured with isophorone diamine (IPD) hardener at different resin to hardener ratios. The aim was to establish correlations between the hardener concentration and the nature and progress of the crosslinking reaction. Insights into the cured resin structure revealed using ToF‐SIMS are discussed. Three sets of significant secondary ions have been identified by PCA. Secondary ions such as C₁₄H₇O⁺, CHO⁺, CH₃O⁺, and C₂₁H₂₄O₄⁺ showed variance related to the completion of the curing reaction. Relative intensities of C_xH_yN_z⁺ ions in the cured resin samples are indicative of the un‐reacted and partially reacted hardener molecules, and are found to be proportional to the resin to hardener mixing ratio. The relative ion intensities of the aliphatic hydrocarbon ions are shown to relate to the cured resin crosslinking density. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Modified carrageenan. 4. Synthesis and swelling behavior of crosslinked κC‐g‐AMPS superabsorbent hydrogel with antisalt and pH‐responsiveness properties

To synthesize a novel biopolymer‐based superabsorbent hydrogel, 2‐acrylamido‐2‐methylpropanesulfonic acid (AMPS) was grafted onto kappa‐carrageenan (κC) backbones. The graft copolymerization reaction was carried out in a homogeneous medium and in the presence of ammonium persulfate (APS) as an initiator, N,N,N′,N′‐tetramethyl ethylenediamine (TMEDA) as an accelerator, and N,N′‐methylene bisacrylamide (MBA) as a crosslinker. A proposed mechanism for κC‐g‐AMPS formation was suggested and the hydrogel structure was confirmed using FTIR spectroscopy. The affecting variables on swelling capacity, i.e., the initiator, the crosslinker, and the monomer concentration, as well as reaction temperature, were systematically optimized. The swelling measurements of the hydrogels were conducted in aqueous solutions of LiCl, NaCl, KCl, MgCl₂, CaCl₂, SrCl₂, BaCl₂, and AlCl₃. Due to the high swelling capacity in salt solutions, the hydrogels may be referred to as antisalt superabsorbents. The swelling of superabsorbing hydrogels was measured in solutions with pH ranging 1 to 13. The κC‐g‐AMPS hydrogel exhibited a pH‐responsiveness character so that a swelling–deswelling pulsatile behavior was recorded at pH 2 and 8. The overall activation energy for the graft copolymerization reaction was found to be 14.6 kJ/mol. The swelling kinetics of the hydrogels was preliminarily investigated as well. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 255–263, 2005     

Curing behavior of epoxy resin having hydroxymethyl group and different molecular weight distribution

o-Cresol novolac-type epoxy resins having hydroxymethyl group were synthesized. These epoxy resins were cured with a mixture of 4,4′-diaminodiphenylmethane and m-phenylenediamine (molar ratio, 6:4) as a hardener. Effects of molecular weight distribution of epoxy resins on curing behavior were studied. Curing behavior of epoxy resins with hardener were examined by differential scanning calorimetery (DSC), and cure reaction parameters were obtained. Viscoelastic properties of the cured epoxy resins were studied by dynamic mechanical analyzer. It was found that the lower the average molecular weight of the epoxy resin, that is, the higher the concentration of hydroxymethyl group, the shorter the onset time of exothermal reaction, the higher the rate constant (k), and the lower the activation energy (E_a) were. It was also found that glass transition temperature (T_g) of fully cured epoxy resins was higher than those of fully cured general novolac-type epoxy resins.     

Curing kinetics and thermal property characterization of o‐CFER/MeTHPA/O‐MMT nanocomposite

The kinetics of the cure reaction for a system of o‐cresol‐formaldehyde epoxy resin (o‐CFER), 3‐methyl‐tetrahydrophthalic anhydride (MeTHPA), N,N‐dimethyl‐benzylamine, and organic montmorillonite(O‐MMT) were investigated by means of X‐ray diffraction (XRD) and differential scanning calorimetry (DSC). The XRD result indicates that an exfoliated nanocomposite was obtained. The analysis of DSC data indicated the behavior was shown in the first stages of the cure for the system, which could be well described by the model proposed by Kamal. In the later stages, the reaction is mainly controlled by diffusion, and diffusion factor, f(α), was introduced into Kamal's equation. In this way, the curing kinetics was predicted well over the entire range of conversion. Molecular mechanism for curing reaction was discussed. The thermal degradation kinetics of the system were investigated by thermogravimetric analysis (TGA), which revealed that with the increase of O‐MMT content, TG curves shift to higher temperature. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3023–3032, 2006     

Platinum(II) as Bifunctional Linker in Antibody–Drug Conjugate Formation: Coupling of a 4‐Nitrobenzo‐2‐oxa‐1,3‐diazole Fluorophore to Trastuzumab as a Model

The potential of platinum(II) as a bifunctional linker in the coordination of small molecules, such as imaging agents or (cytotoxic) drugs, to monoclonal antibodies (mAbs) was investigated with a 4‐nitrobenzo‐2‐oxa‐1,3‐diazole (NBD) fluorophore and trastuzumab (Herceptin?) as a model antibody. The effect of ligand and reaction conditions on conjugation efficiency was explored for [Pt(en)(L‐NBD)Cl](NO₃) (en=ethylenediamine), with L=N‐heteroaromatic, N‐alkyl amine, or thioether. Conjugation proceeded most efficiently at pH 8.0 in the presence of NaClO₄ or Na₂SO₄ in tricine or HEPES buffer. Reaction of N‐coordinated complexes (20 equiv) with trastuzumab at 37 °C for 2 h, followed by removal of weakly bound complexes with excess thiourea, afforded conjugates with an NBD/mAb ratio of 1.5–2.9 that were stable in phosphate‐buffered saline at room temperature for at least 48 h. In contrast, thioether‐coordinated complexes afforded unstable conjugates. Finally, surface plasmon resonance analysis showed no loss in binding affinity of trastuzumab after conjugation.     

Curing kinetics and thermal property characterization of a bisphenol‐S epoxy resin and DDS system

The kinetics of the cure reaction for a system of bisphenol‐S epoxy resin (BPSER), with 4,4′‐diaminodiphenyl sulfone (DDS) as a curing agent was investigated with a differential scanning calorimeter (DSC). Autocatalytic behaviour was observed in the first stages of the cure which can well be described by the model proposed by Kamal, using two rate constants, k₁ and k₂, and two reaction orders, m and n. The overall reaction order, m + n, is in the range 2∼2.5, and the activation energy for k₁ and k₂ was 86.26 and 65.13 kJ mol⁻¹, respectively. In the later stages, a crosslinked network was formed and diffusion control was incorporated to describe the cure. The glass transition temperature (T_g) of the BPSER/DDS samples partially cured isothermally was determined by means of torsional braid analysis (TBA) and the results showed that the reaction rate increased with increasing T_g, in terms of rate constant, but decreased with increasing conversion. It was also found that the  SO₂ group both in the epoxy resin and in the hardener increases the T_g values of the cured materials compared with that of BPAER. The thermal degradation kinetics of this system was investigated by thermogravimetric analysis (TGA). It illustrated that the thermal degradation of BPSER/DDS has nth order reaction kinetics. © 2000 Society of Chemical Industry     

Cure kinetics of a thermosetting liquid dicyanate ester monomer/high-Tg polycyanurate material

The cure of a liquid dicyanate ester monomer, which reacts to form a high-T_g (≈200°C) polycyanurate network, has been investigated using differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), and a dynamic mechanical technique, torsional braid analysis (TBA). The monomer is cured with and without catalyst. The same one-to-one relationship between fractional conversion and the dimensionless glass transition temperature is found from DSC data for both the uncatalyzed and catalyzed systems, independent of cure temperature, signifying that the same polymeric structure is produced. T_g is the parameter used to monitor the curing reactions since it is uniquely related to conversion, is sensitive, is accurately determined, and is also directly related to the solidification process. The rate of uncatalyzed reaction is found to be much slower than that of the catalyzed reaction. The apparent overall activation energy for the uncatalyzed reaction is found to be greater than that of the catalyzed reaction (22 and 13 kcal/mol, respectively) from time–temperature superposition of experimental isothermal T_g vs. In time data to form kinetically-controlled master curves for the two systems. Although the time–temperature superposition analysis does not necessitate knowledge of the rate expression, it has limitations, because if the curing process consists of parallel reactions with different activation energies, as is considered to be the case from analysis of the FTIR data, there should not be a kinetically-controlled master curve. Consequently, a kinetic model, which can be satisfactorily extrapolated, is developed from FTIR isothermal cure studies of the uncatalyzed reaction. The FTIR data for the uncatalyzed system at high cure temperatures, where the material is in the liquid or rubbery states throughout cure, 190 to 220°C, are fitted by a model of two parallel reactions, which are second-order and second-order autocatalytic (with activation energies of 11 and 29 kcal/mol), respectively. Using the model parameters determined from the FTIR studies and the relationship between T_g and conversion from DSC studies, T_g, vs. time curves are calculated for the uncatalyzed system and found to agree with DSC experimental results for isothermal cure temperatures from 120 to 200°C to even beyond vitrification. The DSC data for the catalyzed system are also described by the same kinetic model after incorporating changes in the pre-exponential frequency factors (due to the higher concentration of catalyst) and after incorporating diffusion-control, which occurs prior to vitrification in the catalyzed system (but well after vitrification in the uncatalyzed system). Time–temperature-transformation (TTT) isothermal cure diagrams for both systems are calculated from the kinetic model and compared to experimental TBA data. Experimental gelation is found to occur at a conversion of approximately 64% in the catalyzed system by comparison of experimental macroscopic gelation at the various curing temperatures and iso-T_g (iso-conversion) curves calculated from the kinetic model. © 1993 John Wiley & Sons, Inc.     

Synthesis and characterization of novel heat resistance poly(amide‐imide)s from N,N′‐[2,5‐bis(4‐aminobenzylidene) cyclopentanone] bistrimellitimide acid and various aromatic diamines

A new‐type of dicarboxylic acid was synthesized from the reaction of 2,5‐bis(4‐aminobenzylidene)cyclopentanone with trimellitic anhydride in a solution of glacial acetic acid/pyridine (Py) at refluxing temperature. Six novel heat resistance poly(amide‐imide)s (PAIs) with good inherent viscosities were synthesized, from the direct polycondensation reaction of N,N′‐[2,5‐bis(4‐aminobenzylidene)cyclopentanone]bistrimellitimide acid with several aromatic diamines, by two different methods such as direct polycondensation in a medium consisting of N‐methyl‐2‐pyrrolidone (NMP)/triphenyl phosphite (TPP)/calcium chloride (CaCl₂)/pyridine (Py) and direct polycondensation in a p‐toluene sulfonyl chloride (tosyl chloride, TsCl)/pyridine (Py)/N,N‐dimethylformamide (DMF) system. All of the above polymers were fully characterized by ¹H NMR, FTIR, elemental analysis, inherent viscosity, solubility tests, UV‐vis spectroscopy, differential scanning calorimeter (DSC), thermogravimetric analysis (TGA), and derivative of thermaogravimetric (DTG). The resulted poly(amide‐imide)s (PAIs) have showed admirable good inherent viscosities, thermal stability, and solubility. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermal cure of phenylethynyl‐terminated AFR‐PEPA‐4 imide oligomer and a model compound

The thermal cure reactions of phenylethynyl terminated AFR‐PEPA‐4 oligomer and a model compound N‐phenyl‐[4‐(phenylethynyl) phthalimide] were investigated. The kinetics analysis of the thermal cure of AFR‐PEPA‐4 was determined using DSC, with modified DiBenedetto equation. The activation energy of thermal cure reaction of AFR‐PEPA‐4 oligomer is 34.1 kcal/mol with the kinetic order of one, when the reaction conversion is less than 80%. The activation energy of thermal reaction of N‐phenyl‐[4‐(phenylethynyl) phthalimide] is 41.5 kcal/mol with the kinetic order of 0.95. The cure reaction of AFR‐PEPA‐4 imide oligomer can be described as a fast first‐order reaction stage for the formation of polyenes followed by a slow diffusion‐controlled crosslinking reaction stage. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4446–4453, 2006     

Synthesis and properties of copolymer epoxy resins prepared from copolymerization of bisphenol A,epichlorohydrin, and liquefied Dendrocalamus latiflorus

Dendrocalamus latiflorus Munro (ma bamboo) was liquefied in phenol and polyhydric alcohol (polyethylene glycol/glycerol cosolvent) with H₂SO₄ as catalyst. Liquefied bamboos reacted with bisphenol A and epichlorohydrin were then employed to prepare copolymer epoxy resins. The curing property and thermal property of copolymer epoxy resins were investigated. The results showed that copolymer epoxy resins could cure at room temperature after the hardener was added, and its curing process was an exothermic reaction. Comparison showed that copolymer epoxy resins prepared with phenol‐liquefied bamboo as raw material had higher heat released than those prepared with polyhydric alcohol‐liquefied bamboo during curing. The DSC analysis showed that heat treatment could enhance the crosslinking of copolymer epoxy resins cured at room temperature. However, resins prepared with polyhydric alcohol‐liquefied bamboo had a lower glass transition temperature. The TGA analysis showed that resins prepared with phenol‐liquefied bamboo had better thermal stability. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis of poly[(2‐oxo‐1,3‐dioxolan‐4‐yl)methyl vinyl ether‐co‐N‐phenylmaleimide] and its miscibility in blends with styrene‐acrylonitrile or poly(vinyl chloride)

The aim of the study was to investigate the synthesis of a copolymer bearing cyclic carbonate and its miscibility with styrene/acrylonitrile copolymer (SAN) or poly(vinyl chloride) (PVC). (2‐Oxo‐1,3‐dioxolan‐4‐yl)methyl vinyl ether (OVE) as a monomer was synthesized from glycidyl vinyl ether and CO₂ using quaternary ammonium chloride salts as catalysts. The highest reaction rate was observed when tetraoctylammonium chloride (TOAC) was used as a catalyst. Even at the atmospheric pressure of CO₂, the yield of OVE using TOAC was above 80% after 6 h of reaction at 80°C. The copolymer of OVE and N‐phenylmaleimide (NPM) was prepared by radical copolymerization and was characterized by FTIR and ¹H‐NMR spectroscopies and differential scanning calorimetry (DSC). The monomer reactivity ratios were given as r₁ (OVE) = 0.53–0.57 and r₂ (NPM) = 2.23–2.24 in the copolymerization of OVE and NPM. The films of poly(OVE‐co‐NPM)/SAN and poly(OVE‐co‐NPM)/PVC blends were cast from N‐dimethylformamide. An optical clarity test and DSC analysis showed that poly(OVE‐co‐NPM)/SAN and poly(OVE‐co‐NPM)/PVC blends were both miscible over the whole composition range. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1809–1815, 2000     

Thermal decomposition of poly(glycidyl azide) as studied by high-temperature FTIR and thermogravimetry

Thermal decomposition of poly(glycidyl azide) (PGA) has been studied by using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and high-temperature FTIR spectrometry. By using DSC and TGA techniques, the first stage weight loss of PGA due to exothermic decomposition of pendant azide ( N₃) groups was explained in terms of the energy released at every stage of decomposition. From the glass transition temperature (T_g) measurements, it was observed that T_g values of PGA increased with increasing quantity of decomposed  N₃ groups. The course of the decomposition reaction was also studied by taking successive FTIR spectra. It was observed that during the first stage weight loss process of PGA, the main chain was not decomposed thermally; inter- and intramolecular linking reactions accompanied the side chain decompositions. © 1996 John Wiley & Sons, Inc.