Nonisothermal crystallization kinetics and thermomechanical properties of multiwalled carbon nanotube‐reinforced poly(ε‐caprolactone) composites

BACKGROUND: The technological development of poly(ε‐caprolactone) (PCL) is limited by its short useful lifespan, low modulus and high crystallinity. There are a few papers dealing with the crystallization behavior of carbon nanotube‐reinforced PCL composites. However, little work has been done on the crystallization kinetics of melt‐compounded PCL/multiwalled carbon nanotube (MWNT) nanocomposites. In this study, PCL/MWNT nanocomposites were successfully prepared by a simple melt‐compounding method, and their morphology and mechanical properties as well as their crystallization kinetics were studied. RESULTS: The MWNTs were observed to be homogeneously dispersed throughout the PCL matrix. The incorporation of a very small quantity of MWNTs significantly improved the storage modulus and loss modulus of the PCL/MWNT nanocomposites. The nonisothermal crystallization behavior of the PCL/MWNT nanocomposites exhibits strong dependencies of the degree of crystallinity (X_c), peak crystallization temperature (T_p), half‐time of crystallization (t_1/2) and Avrami exponent (n) on the MWNT content and cooling rate. The MWNTs in the PCL/MWNT nanocomposites exhibit a higher nucleation activity. The crystallization activation energy (E_a) calculated with the Kissinger model is higher when a small amount of MWNTs is added, then gradually decreases; all the E_a values are higher than that of pure PCL. CONCLUSION: This paper reports for the first time the preparation of high‐performance biopolymer PCL/MWNT nanocomposites prepared by a simple melt‐compounding method. The results show that the PCL/MWNT nanocomposites can broaden the applications of PCL. Copyright © 2008 Society of Chemical Industry     

Nanocomposites based on poly(ϵ‐caprolactone) and the montmorillonite treated with dibutylamine‐terminated ϵ‐caprolactone oligomer

Dibutylamine‐terminated ε‐caprolactone oligomers (CLOs: CLOL, CLOM, and CLOH) with number–averaged molecular weight (M_n), 500, 1300, and 2200, respectively, were synthesized by the ring‐opening polymerization of ε‐caprolactone initiated by 2‐(dibutylamino)ethanol in the presence of tin(II) 2‐ethylhexanoate. Nanocomposites based on poly(ε‐caploractone) (PCL) and the caprolactone oligomer‐treated montmorillonites (CLO‐Ms: CLOL‐M, CLOM‐M, and CLOH‐M) were prepared by melt intercalation method. The XRD and TEM analyses of the PCL composites revealed that the extent of exfoliation of the clay platelets increased with increasing molecular weight of the used CLOs. Tensile strength and modulus of the PCL/CLO‐M composites increased with increasing molecular weight of the CLO and increasing inorganic content. The tensile modulus of the PCL/CLOH‐M nanocomposite with inorganic content 5.0 wt % was three times higher than that of control PCL. Among the PCL/CLO‐M composites, the PCL/CLOM‐M composite had the highest crystallization temperature and melting temperature. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Micro structural and non‐isothermal crystallization and degradation kinetics studies on manganese thioglycolate end capped poly(ε‐caprolactone)

The Manganese thioglycolate (Mn‐TG) end capped poly(ε‐caprolactone) (PCL) was prepared by ring opening polymerization at 160°C under inert atmosphere in the presence of Mn‐TG as an initiator and stannous octoate as a catalyst by bulk polymerization technique. The prepared PCL was investigated using various analytical tools to assess its physico‐chemical properties. The chemical structure of PCL was confirmed by Fourier transform infrared and nuclear magnetic resonance spectroscopic techniques. The particle size and morphology of the sample was examined by atomic force microscopy and TEM. The melting and crystallization behavior of PCL was analyzed using differential scanning calorimetry. The thermal property of PCL was assessed with the help of thermogravimetric analysis (TGA). The non‐isothermal crystallization kinetics was carried out to understand the nucleation type and crystal growth for the prepared PCL. The energy of activation (E_a) for crystallization process of PCL was determined. The thermal degradation of PCL and its E_a was determined under non‐isothermal condition using important kinetic models. POLYM. ENG. SCI., 59:633–642, 2019. © 2018 Society of Plastics Engineers     

Isothermal crystallization kinetics of silk fibroin fiber‐reinforced poly(ε‐caprolactone) biocomposites

BACKGROUND: Poly(ε‐caprolactone) (PCL) has attracted great attention due to its wide applications for pharmaceutical controlled released systems and implanted polymer devices. In this study, silk fibroin fiber (SF) obtained from degumming treatment of silk was used to prepare novel reinforced PCL biocomposites. The isothermal crystallization behavior of these composites was investigated using differential scanning calorimetry measurements. RESULTS: With a decrease of isothermal crystallization temperature (T_c) and an increase of fiber filler, the crystallization time of the SF/PCL composites becomes shorter, the crystallization rate constant (K) increases and the Avrami exponent (n) gradually decreases (being between 1 and 2). The crystallization of PCL and SF/PCL composites occurs in the same regime. With the gradual addition of fiber, lateral surface free energy (σ) is nearly unchanged, but fold surface free energy (σ_e) decreases. CONCLUSION: Heterogeneous nucleation is dominant and different growth morphologies coexist during the isothermal crystallization process of the SF/PCL hybrid systems. Although the introduction of SF obviously increases the overall crystallization rate of PCL, the growth rate constant and nucleation constant of PCL are reduced because of the confinement effect of fiber network structures on the molecular mobility of polymer molecular chains. Copyright © 2009 Society of Chemical Industry     

Poly(ϵ‐caprolactone)‐functionalized carbon nanofibers by surface‐initiated ring‐opening polymerization

Carbon nanofibers (CNFs) were covalently functionalized with biodegradable poly(?‐caprolactone) (PCL) by in situ ring‐opening polymerization (ROP) of ?‐caprolactone in the presence of stannous octoate. Surface oxidation treatment of the pristine CNFs afforded carboxylic CNFs (CNF‐COOH). Reaction of CNF‐COOH with excess thionyl chloride (SOCl₂) and glycol produced hydroxyl‐functionalized CNFs (CNF‐OH). Using CNF‐OH as macroinitiator, PCL was covalently grafted from the surfaces of CNFs by ROP, in either the presence or absence of sacrificial initiator, butanol. The grafted PCL content was achieved as high as 64.2 wt %, and can be controlled to some extent by adjusting the feed ratio of monomer to CNF‐OH. The resulting products were characterized by FTIR, NMR, Raman spectroscopy, TGA, DSC, SEM, TEM, HRTEM, and XRD. Core–shell nanostructures were observed under HRTEM for the PCL‐functionalized CNFs because of the thorough grafting. The PCL‐grafted CNFs showed different melting and crystallization behaviors from the mechanical mixture of PCL and CNF‐OH. This approach to PCL‐functionalized CNFs opens an avenue for the synthesis, modification, and application of CNF‐based nanomaterials and biomaterials. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Isothermal crystallization kinetics of biodegradable poly(lactic acid)/poly(ε‐caprolactone) blends compatibilized with low‐molecular weight block copolymers

The isothermal crystallization kinetics of biodegradable blends made of poly(lactic acid) (PLA) and poly(ε‐caprolactone) (PCL) compatibilized with two different low molecular weight block copolymers, that is, ε‐caprolactone/tetramethylene ether glycol and ε‐caprolactone/aliphatic polycarbonate (CB), was done. Blends were prepared by melt mixing in an extruder, while isothermal crystallization kinetics and morphologies were investigated by thermal (differential scanning calorimetry) and thermo‐optical (quantitative polarized light optical microscopy [qPLOM]) quantitative methods. Data were analyzed using the Avrami equation, revealing 2D and 3D growth and simultaneous heterogeneous nucleation. The presence of low molecular weight compatibilizers, that is, 2,000 g mol^?1, accelerated the PLA crystallization rate by two to threefold when compared with neat PLA, with high degrees of crystallinity (40–43%) as confirmed by PLOM images. The activation energy (E_a) showed that PCL inhibits PLA crystallization; however, the addition of block copolymers used as compatibilizers of the blends reduced E_a values, increasing the chain mobility of PLA and thus increasing the crystallization rate. POLYM. ENG. SCI., 59:E161–E169, 2019. © 2018 Society of Plastics Engineers     

Non‐isothermal crystallization kinetics of poly(ε‐caprolactone) in hydrogen‐bond‐coupled polymeric‐inorganic hybrid materials

Some hydrogen‐bonding‐interactions‐mediated poly(ε‐caprolactone) (PCL)/silica (SiO₂) polymeric‐inorganic hybrids were prepared by the sol–gel process. The non‐isothermal crystallization kinetics of PCL in the hybrids was investigated by means of differential scanning calorimetry. The results show that the Jeziorny method, together with the combination of the Avrami and Ozawa equations, is applicable to describe the non‐isothermal crystallization kinetics of the PCL in the hybrid system, while the Ozawa theoretical method can be used just for the pure PCL and the 70/30 TEOS/PCL hybrids. Depending on the composition of the PCL/silica, the hybrids displayed microphase separation at various scales, which in turn affect the crystallization behavior and mechanism of PCL in the hybrids. On the one hand, the inorganic component (viz SiO₂) could act as the nucleating agent to facilitate the crystallization of PCL in the hybrids. On the other hand, the SiO₂ networks also confine the crystallization of PCL. Copyright © 2004 Society of Chemical Industry     

Effects of nano‐TiO2 on the properties and structures of starch/poly(ε‐caprolactone) composites

Poor physical properties resulting from low interfacial interactions between hydrophilic biopolymers and hydrophobic thermoplastic matrices have been one of the biggest obstacles in preparing quality biomass materials. This study concentrates on the effects of nano‐TiO₂ on the properties and structure of starch/poly (ε‐caprolactone) (PCL) composites. The molecular and crystal structures of the composites were characterized by using Fourier transform infrared spectroscopy, differential scanning calorimeter (DSC), X‐ray diffraction (XRD), and field emission scanning electron microscope. The results indicated that an interpenetrating network structure formed by adding nano‐TiO₂ into starch/PCL composites. The DSC and XRD analysis indicated that the crystallinity degree and the crystallization rate of the composites reduced, whereas the crystal form and crystal size were unchanged. The results also showed that the mechanical properties and water resistance of the composites were improved significantly with the addition of nano‐TiO₂, whereas their transparency decreased. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4129–4136, 2013     

Synthesis and characterization of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers with dibutylmagnesium as catalyst

Two series of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers were prepared by the ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) and dibutylmagnesium in 1,4‐dioxane solution at 70°C. The triblock structure and molecular weight of the copolymers were analyzed and confirmed by ¹H NMR, ¹³C NMR, FTIR, and gel permeation chromatography. The crystallization and thermal properties of the copolymers were investigated by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). The results illustrated that the crystallization and melting behaviors of the copolymers were depended on the copolymer composition and the relative length of each block in copolymers. Crystallization exothermal peaks (T_c) and melting endothermic peaks (T_m) of PEG block were significantly influenced by the relative length of PCL blocks, due to the hindrance of the lateral PCL blocks. With increasing of the length of PCL blocks, the diffraction and the melting peak of PEG block disappeared gradually in the WAXD patterns and DSC curves, respectively. In contrast, the crystallization of PCL blocks was not suppressed by the middle PEG block. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermal,mechanical, and rheological properties of poly(ε‐caprolactone)/halloysite nanotube nanocomposites

Naturally available halloysite nanotubes (HNTs) with hollow nanotubular structures were used as reinforcement in poly(ε‐caprolactone) (PCL). The PCL/HNT nanocomposites were prepared by melt mixing the polymer with as‐received HNTs up to 10 wt % in an internal batch mixer. Transmission electron microscopy analysis indicated that the HNTs were dispersed uniformly on the nanoscale throughout the PCL matrix. Differential scanning calorimeter studies revealed that the PCL crystallinity was decreased in the nanocomposites, and the HNTs dispersed in the PCL matrix led to an increase in the non‐isothermal crystallization temperature of the PCL. Tensile and dynamic mechanical tests showed great enhancement in strength and stiffness at low HNT content, while still maintaining the ductility of the PCL. The glass transition temperature (T_g) of the pristine PCL was substantially increased with increase in filler loading, which indicates good reinforcing effect imparted by the addition of HNT. Melt rheological studies revealed that the nanocomposites exhibited strong shear thinning behavior, and a percolated network of HNT particles was formed. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Compatibilization and ultraviolet blocking of PLA/PCL blends via interfacial localization of titanium dioxide nanoparticles

In this work, the effect of TiO₂ addition over morphological and ultraviolet (UV) blocking properties of poly(lactic acid) (PLA) and poly(?‐caprolactone) (PCL) blends was investigated. The micrographs showed a partially co‐continuous structure in the PLA/PCL blend with 42/58 (wt %/wt %) and the TiO₂ nanoparticles addition leads to a structural phase inversion, i.e., continuous PCL and partially continuous PLA with a dispersed portion. TiO₂ nanoparticles were observed to be preferably localized at the interface of the two phases due to kinetic effects (large difference between the melting temperatures) and nanoparticle geometry (low aspect ratios). An adhesion improvement between the phases and morphological stability were observed with the addition of TiO₂ nanoparticles. This behavior indicates that the nanoparticles can act as compatibilizers due to their localization at the interface between the two phases. The UV light absorption and transmission percolation threshold occurred with 1.5% TiO₂ in the 42PLA/52PCL blend. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45813.     

Influence of semi‐crystalline poly(ε‐caprolactone) and non‐crystalline polylactide blocks on the thermal properties of polydimethylsiloxane‐based block copolymers

Poly(A)‐block‐poly(B), poly(A)‐block‐poly(B)‐block‐poly(A) and B(A)₂ block copolymers were prepared through coordinated anionic ring‐opening polymerization of ε‐caprolactone (CL) and lactic acid (LA) using hydroxy‐terminated polydimethylsiloxane (PDMS) as initiator. A wide range of well‐defined combinations of PDMS‐block‐PCL and PDMS‐block‐PLA diblock copolymers, PCL‐block‐PDMS‐block‐PCL and PLA‐block‐PDMS‐block‐PLA triblock copolymers and star‐PDMS(PCL)₂ copolymers were thus obtained. The number‐average molar masses and the structure of the synthesized block copolymers were identified using various analytical techniques. The thermal properties of these copolymers were established using differential scanning calorimetry. Considering PDMS‐block‐PCL copolymers, the results demonstrate the complex effect of polymer architecture and PCL block length on the ability of the PDMS block to crystallize or not. In the case of diblock copolymers, crystallization of PCL blocks originated from stacking of adjacent chains inducing the extension of the PDMS block that can easily crystallize. In the case of star copolymers, the same tendency as in triblock copolymers is observed, showing a limited crystallization of PDMS when the length of the PCL block increases. In the case of PDMS‐block‐PLA copolymers, melting and crystallization transitions of the PLA block are never observed. Considering the diblock copolymers, PDMS sequences have the ability to crystallize. © 2019 Society of Chemical Industry     

Phosphorylcholine end‐capped poly‐ε‐caprolactone: A novel biodegradable material with improved antiadsorption property

In this study, the synthesis, characterization, and properties of a novel biodegradable polymer with improved hemocompatibility were introduced. It was synthesized by end‐capping poly‐ε‐caprolactone (PCL) with phosphorylcholine (PC) groups. The polyester backbone provided the mechanical stability and biodegradability, while the PC‐end groups improved its hemocompatibility. The obtained polymer was characterized using ¹H NMR, ³¹P NMR, FTIR, and GPC, its crystallization behavior was studied by DSC. Compared with original PCL, the resulting polymer (PC‐PCL) showed a lower crystallization capability and a faster degradation rate in PBS. The degradation rate of the polymer blends of PCL/PC‐PCL increased with increasing PC‐PCL content. The results of water contact angle measurements revealed a more hydrophilic surface property of PC‐PCL than neat PCL. The hemocompatibility of PC‐PCL was estimated using rabbit platelet‐rich plasma, a better resistance to platelet adhesion and activation was observed. During the human blood plasma contacting process, PC‐PCL showed a prolonged activated partial thromboplastin time over neat PCL. Material–cell interaction was evaluated with human umbilical vein endothelial cell, the result indicated that PC‐PCL may to some extent have an antihyperplasia property, compared with neat PCL. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 989–997, 2007     

Effect of electron beam irradiation on the crystallization of silk fibroin fiber‐reinforced poly(ε‐caprolactone) biocomposites

In the medical industry, ionizing radiation has attracted increasing interest in recent years for the sterilization of biomedical materials due to its high effectiveness at relatively low cost and simple operation. In the study reported here, silk fibroin (SF) fiber was used to prepare novel reinforced poly(ε‐caprolactone) (PCL) biocomposites, and the effect of electron beam irradiation on both non‐isothermal and isothermal crystallization kinetics of the SF/PCL biocomposites was investigated. The models of Ozawa treatment, Avrami analysis and regime theory of crystal growth are applicable for describing the non‐isothermal and isothermal crystallization kinetics of the irradiated PCL and SF/PCL composites. Compared with non‐irradiated PCL and SF/PCL composites, the irradiated specimens exhibit the same crystallization regime (regime II) and similar lateral surface free energy (σ), except for smaller fold surface free energy (σ_e) and work of chain folding (q). The crosslinked PCL network formed in the irradiation process can act as a nucleation agent and accelerate the primary crystallization of PCL. However, the restriction effect of the crosslinked PCL network on the molecular chain mobility will reduce the overall crystallization rate of PCL, and this restriction effect appears stronger in the non‐isothermal crystallization process than in the isothermal crystallization process. Copyright © 2009 Society of Chemical Industry     

Enhanced crystallization rate and mechanical properties of poly(l‐lactic acid) by stereocomplexation with four‐armed poly(ϵ‐caprolactone)‐block‐poly(d‐lactic acid) diblock copolymer

Poly(l ‐lactic acid) (PLLA) was blended with a series of four‐armed poly(? ‐caprolactone)‐block ‐poly(d ‐lactic acid) (4a‐PCL‐b ‐PDLA) copolymers in order to improve its crystallization rate and mechanical properties. It is found that a higher content of 4a‐PCL‐b ‐PDLA copolymer or longer PDLA block in the copolymer lead to faster crystallization of the blend, which is attributed to the formation of stereocomplex crystallites between PLLA matrix and PDLA blocks of the 4a‐PCL‐b ‐PDLA copolymers. Meanwhile, the PDLA block can improve the miscibility between flexible PCL phase and PLLA phase, which is beneficial for improving mechanical properties. The tensile results indicate that the 10% 4a‐PCL_5k‐b ‐PDLA_5k/PLLA blend has the largest elongation at break of about 72% because of the synergistic effects of stereocomplexation between enantiomeric PLAs, multi‐arm structure and plasticization of PCL blocks. It is concluded that well‐controlled composition and content of 4a‐PCL‐b ‐PDLA copolymer in PLLA blends can significantly improve the crystallization rate and mechanical properties of the PLLA matrix. © 2017 Society of Chemical Industry     

Thermal and mechanical properties of semi‐interpenetrating polymer networks composed of diisocyanate‐bridged,four‐armed,star‐shaped ε‐caprolactone oligomers and poly(ε‐caprolactone)

Semi‐interpenetrating polymer networks (S‐IPNs) were prepared by the reactions of hydroxyl‐terminated four‐armed, star‐shaped ε‐caprolactone oligomers with degrees of polymerization per one oligocaprolactone chain (ns) of 3, 5, and 10 and 2,4‐tolylene diisocyanate (TDI) in the presence of poly(ε‐caprolactone) (PCL). In the dynamic mechanical analysis of the S‐IPN [2,4‐tolylene diisocyanate bridged hydroxyl‐terminated four‐armed, star‐shaped ε‐caprolactone oligomer (TH4CLO)/PCL], only one tan δ peak was observed; its temperature increased with increasing TH4CLO content and with decreasing n value. Differential scanning calorimetric analyses of the TH4CLOs and TH4CLO/PCLs revealed that the TH4CLOs with ns of 3 and 5 were amorphous, whereas TH4CLO with an n of 10 was semicrystalline and that the crystallization of the PCL chain for TH4CLO/PCLs was more strongly disturbed with increasing TH4CLO content and decreasing n value. Although the tensile strength, modulus, and elongation at break of TH4CLO were much lower than those of PCL, those values increased with the n value. Although the tensile strength and modulus of the TH4CLO/PCLs decreased with increasing TH4CLO content, TH4CLO (n = 3)/PCL 50/50 showed the highest elongation at break (314%) among the S‐IPNs because of the suppression of crystallization of the polycaprolactone chain. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4229–4236, 2013     

Polymorphism and crystallization in poly(vinylidene fluoride)/ poly(ϵ‐caprolactone)–block–poly(dimethylsiloxane)–block–poly(ϵ‐caprolactone) blends

The miscibility, crystallization kinetics and crystalline morphology of a new system of poly(vinylidene fluoride)/poly(?‐caprolactone)‐block‐poly(dimethylsiloxane)‐block‐poly(?‐caprolactone) (PVDF/PCL‐b‐PDMS‐b‐PCL) triblock copolymer were investigated by a variety of techniques. The miscibility and phase behaviour of PVDF/PCL‐b‐PDMS‐b‐PCL were studied by determination of the melting point temperature, crystallization kinetics and Fourier transform infrared (FTIR) mapping. Chemical imaging was used as a new technique to characterize the interaction of polymer blends in crystalline morphology. The results demonstrate the existence of characteristic peaks of both PVDF and PCL in the chosen crystalline area. The crystalline structures of PVDF were affected by the PCL‐b‐PDMS‐b‐PCL triblock copolymer and facilitate the formation of the β polymorph which was illustrated by FTIR analysis. The β crystal phase fraction increases significantly on increasing the composition of the PCL‐b‐PDMS‐b‐PCL triblock copolymer. In addition, confined crystallization of PCL within PVDF inter‐lamellar and/or inter‐fibrillar regions was confirmed through polarizing optical microscopy, wide‐angle X‐ray diffraction and small‐angle X‐ray scattering analysis. © 2019 Society of Chemical Industry     

Nonisothermal crystallization behaviors of silk‐fibroin‐fiber‐reinforced poly(ϵ‐caprolactone) biocomposites

With differential scanning calorimetry measurements, the nonisothermal crystallization of biocomposites of poly(?‐caprolactone) (PCL) reinforced with silk fibroin fiber (SF) was investigated. With the gradual addition of SF, the strengthening of the heterogeneous nucleation reagent effect of SF led to the acceleration of PCL crystallization, and secondary crystallization occurred and became more remarkable with increases in the cooling rate and SF content. Moreover, with the introduction of SF and an increase in the cooling rate, the nucleation and growth mode of the PCL crystalline phase was slightly changed. Because of the confinement of the fiber network structure, the crystallite size of PCL was reduced, the crystallization exothermicity of PCL decreased, and the crystallization activation energy of PCL increased. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Rheological investigation of polyamide 6 TiO2‐ and BaSO4‐nanocomposites

Commercially available TiO₂ and BaSO₄ nanoparticles were incorporated in polyamide 6 (PA 6) via twin screw extrusion. The primary particle size of nanoparticles was 15 nm and 20 nm. The compounds were manufactured via multiple extrusion and dilution processing steps. The dispersion of the nanoparticles in the matrix was investigated by scanning electron microscopy and image analysis, micro‐tomography, and transmission electron microscopy. The rheological properties were determined via plate–plate‐rheometer. It was found that for TiO₂ fillers a threefold extrusion process is sufficient to realize a dispersion index of 94.4%. BaSO₄ fillers were hardly dispersible, ending up with a maximum dispersion index of 71%. Deagglomeration does not lead to a change in rheological properties but the number of extrusion steps decreases the rheological properties. A good particle‐matrix interaction leads to higher moduli and viscosity. The remaining agglomerates seem to act as defects decreasing the energy absorption of the respective compounds. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Chemical immobilization of retinoic acid within poly(ε‐caprolactone) nanoparticles based on drug–polymer bioconjugates

All‐trans‐retinoic acid (RA) was chemically conjugated to biodegradable poly(ε‐caprolactone) (PCL₁₀; number‐average M_w ≈ 1250) via an ester linkage. The conjugation was carried out using N,N‐dicyclohexylcarbodiimide and 4‐dimethyl aminopyridine as a coupling agent. The molar ratio of the drug to the polymer was 1.11 as determined by ¹H‐NMR analysis. DSC and WAXD results showed that the formation of crystalline structures of RA was effectively suppressed by conjugation with PCL. The RA–PCL conjugates were formulated into nanoparticles by a spontaneous phase‐inversion technique. Morphological characteristics of the resultant nanoparticles and drug‐loading efficiencies were compared with those of free RA‐loaded nanoparticles. The drug‐loading efficiency of RA–PCL conjugates was almost 100%, while that of free RA was only ～12%. The majority of unconjugated RA was found to form undesirable free‐drug crystals out of nanoparticles, as observed by TEM analysis. This study demonstrates that the conjugation approach of RA to PCL can be an effective means to immobilize and encapsulate RA within nanoparticles for pharmaceutical applications. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1631–1637, 2003