Preparation and characterization of microbial biodegradable poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)/organoclay nanocomposites

Novel biodegradable poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) [P(3HB‐co‐4HB)]/organoclay nanocomposites were prepared via solution casting. Exfoliated nanocomposite structure was confirmed by wide‐angle X‐ray diffraction (WAXD) and transmission electron microscopy (TEM) for the nanocomposites with low organoclay loadings (≤3 wt%), whereas the mixtures of exfoliated and unexfoliated organoclays were appeared in the nanocomposite with an organoclay content of 5 wt%. The organoclay fillers accelerated significantly the cold crystallization process of P(3HB‐co‐4HB) matrix. The thermal stability of the nanocomposites was in general better than that of pristine P(3HB‐co‐4HB). Considerable increase in tensile modulus was observed for the nanocomposites, especially at an organoclay content of 3 wt%. These results demonstrated that the nanocomposites improved the material properties of P(3HB‐co‐4HB). POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Miscibility and crystallization behaviors of poly(3‐hydroxybutyrate‐co‐11%‐4‐hydroxybutyrate)/Poly(3‐hydroxybutyrate‐co‐33%‐4‐hydroxybutyrate) blends

Biopolyesters poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) with an 11 mol % 4HB content [P(3HB‐co‐11%‐4HB)] and a 33 mol % 4HB content [P(3HB‐co‐33%‐4HB)] were blended by a solvent‐casting method. The thermal properties were investigated with differential scanning calorimetry. The single glass‐transition temperature of the blends revealed that the two components were miscible when the content of P(3HB‐co‐33%‐4HB) was less than 30% or more than 70 wt %. The blends, however, were immiscible when the P(3HB‐co‐33%‐4HB) content was between 30 and 70%. The miscibility of the blends was also confirmed by scanning electron microscopy morphology observation. In the crystallite structure study, X‐ray diffraction patterns demonstrated that the crystallites of the blends were mainly from poly(3‐hydroxybutyrate) units. With the addition of P(3HB‐co‐33%‐4HB), larger crystallites with lower crystallization degrees were induced. Isothermal crystallization was used to analyze the melting crystallization kinetics. The Avrami exponent was kept around 2; this indicated that the crystallization mode was not affected by the blending. The equilibrium melting temperature decreased from 144 to 140°C for the 80/20 and 70/30 blends P(3HB‐co‐11%‐4HB)/P(3HB‐co‐33%‐4HB). This hinted that the crystallization tendency decreased with a higher P(3HB‐co‐33%‐4HB) content. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Morphology and properties of biodegradable and biosourced polylactide blends with poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)

Biodegradable polymer blends based on biosourced polymers, namely polylactide (PLA) and poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P(3HB‐co‐4HB)), were prepared by melt compounding. The effects of P(3HB‐co‐4HB) on the miscibility, phase morphology, thermal behavior, mechanical properties, and biodegradability of PLA/P(3HB‐co‐4HB) blends were investigated. The blend was an immiscible system with the P(3HB‐co‐4HB) domains evenly dispersed in the PLA matrix. However, the T_g of P(3HB‐co‐4HB) component in the blends decreased compared with neat P(3HB‐co‐4HB), which might be attributed to that the presence of the phase interface between PLA and P(3HB‐co‐4HB) resulted in enhanced chain mobility near interface. The addition of P(3HB‐co‐4HB) enhanced the cold crystallization of PLA in the blends due to the nucleation enhancement of PLA caused by the enhanced chain mobility near the phase interface between PLA and P(3HB‐co‐4HB) in the immiscible blends. With the increase in P(3HB‐co‐4HB) content, the blends showed decreased tensile strength and modulus; however, the elongation at beak was increased significantly, indicating that the inherent brittlement of PLA was improved by adding P(3HB‐co‐4HB). The interesting aspect was that the biodegradability of PLA is significantly enhanced after blends preparation. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Miscibility,crystallization, and mechanical properties of poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)/ poly(butylene succinate) blends

Naturally amorphous biopolyester poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P3/4HB) containing 21 mol % of 4HB was blended with semi‐crystal poly(butylene succinate) (PBS) with an aim to improve the properties of aliphatic polyesters. The effect of PBS contents on miscibility, thermal properties, crystallization kinetics, and mechanical property of the blends was evaluated by DSC, TGA, FTIR, wide‐angle X‐ray diffractometer (WAXD), Scanning Electron Microscope (SEM), and universal material testing machine. The thermal stability of P3/4HB was enhanced by blending with PBS. When PBS content is less than 30 wt %, the two polymers show better miscibility and their crystallization trend was enhanced by each other. The optimum mechanical properties were observed at the 5–10 wt % PBS blends. However, when the PBS content is more than 30 wt %, phase inversion happened. And the two polymers give lower miscibility and poor mechanical properties. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Mechanical properties,thermal stability,and crystallization kinetics of poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)/calcium carbonate composites

Bacterial polyester poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P3/4HB) containing 5 mol% 4HB was composited with different calcium carbonate (CaCO₃) fillers. The effect of CaCO₃ contents on thermal properties, mechanical property, and crystallization kinetics was evaluated. The thermal stability of P3/4HB was reduced by mixing with CaCO₃ particles. With increasing CaCO₃ content, the elongation at break, tensile strength, and impact strength decrease; however, elastic modulus increases. When P3/4HB with 20 mol% 4HB was added into the P3/4HB/CaCO₃ composite, the impact strength were enhanced significantly; however, the elongation at break and tensile strength were only slight to moderate improvements. However, when compared with nano‐ and light‐CaCO₃, heavy CaCO₃ had the best mechanical properties. The nonisothermal and isothermal crystallization results demonstrated that the crystallization rate of P3/4HB was reduced and the highest crystallinity was obtained for all kinds of CaCO₃ fillers at 40 phr content. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Rheological,thermal, and mechanical properties of P (3HB‐co‐4HB) and P (3HB‐co‐4HB)/EVA blends

Poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) [P(3HB‐co‐4HB)] fiber and P(3HB‐co‐4HB)/EVA fiber were obtained by single screw extrusion machine. The rheology of P(3HB‐co‐4HB) and P(3HB‐co‐4HB)/EVA blends was characterized by capillary rheometer, and the chemical groups of the blends were characterized with Fourier transform infrared spectroscopy (FT‐IR). The crystallization behavior and thermal, mechanical and elastic properties of the fibers were measured by differential scanning calorimeter (DSC), thermogravimetric analyzer (TGA) and single fiber strength tester, respectively. Besides, the moisture regain and drying shrinkage rates of the fibers were tested. These results showed that P(3HB‐co‐4HB)/EVA blends have better flowability, crystallinity, and thermal stability than P(3HB‐co‐4HB) fiber. The fracture strength of the P(3HB‐co‐4HB)/EVA fiber decreases with increasing the EVA content, but the elongation at break shows the contrary tendency. The rebound resilience ratio of P(3HB‐co‐4HB)/EVA fiber reaches 100%. Both moisture regain and drying shrinkage increase first and then decrease with increasing the EVA content. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41206.     

Thermal stability of poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)/modified montmorillonite bio‐nanocomposites

Poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P34HB)/modified montmorillonite (EMMT) bio‐nanocomposites were prepared via melt intercalation method. The thermal stability of the bio‐nanocomposites was investigated. The results showed that the decomposition temperature (T _5%) of P34HB/EMMT bio‐nanocomposite reached 271.4°C, 39.9°C higher than that of pure P34HB. The remarkable thermal stability enhancement was presumably originated from the uniform dispersion of EMMT in the matrix and intercalated structures of P34HB/EMMT bio‐nanocomposites, which was related to the increased compatibility of EMMT and P34HB caused by the ester group in EMMT. TGA‐FTIR analysis on the thermal degradation procedures of the bio‐nanocomposites manifested that the introduction of EMMT did not alter the degradation mechanism of P34HB. However, the intercalated structures hindered the mobility of P34HB macromolecular and slowed down the decomposing process of P34HB. POLYM. COMPOS., 38:673–681, 2017. © 2015 Society of Plastics Engineers     

The influence of 4HB content on the properties of poly(3‐hydroxylbutyrate‐co‐4‐hydroxylbutyrate) based on melt molded sheets

A series of poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)s[P(3HB‐co‐4HB)s] sheets with the 4HB contents from about 9 to 34 mol % were prepared via melt molding. Their crystallinity, crystalline structures, thermal and mechanical properties were characterized by differential scanning calorimetry, X‐ray diffraction, thermogravimetric analysis, dynamic mechanical analysis, and tensile test. It was found that the melt temperatures (T_m), glass transition temperatures (T_g), and storage modulus (E′) of all the [P(3HB‐co‐4HB)s] copolymers investigated decreased continuously with increasing the amount of the 4HB; the yield stress and breaking stress nearly decreased with the increase of the 4HB contents while the elongation at the yield and break points increased; and the thermal stability of the P(3HB‐co‐4HB)s improved with increasing 4HB contents. The results suggest that the mechanical properties and crystal lattice parameters of the melt molded sheets are somewhat different from those of the solution cast films. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Miscibility,crystallization kinetics,and mechanical properties of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)(PHBV)/poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)(P3/4HB) blends

Poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)(PHBV)/poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P3/4HB) blend films were prepared by solvent‐cast method. The nonisothermal crystallization results showed that PHBV and P3/4HB are miscible due to a single glass transition temperature (T_g), which is dependent on blend composition. The isothermal crystallization results demonstrate that the crystallization rate of PHBV becomes slower after adding amorphous P3/4HB with 19.2 mol% 4HB, which could be proved through depression of equilibrium melt point ($T_m^o$ ) from 183.7°C to 177.6°C. For pure PHBV and PHBV/P3/4HB (80/20) blend, the maximum crystallization rate appeared at 88°C and 84°C, respectively. FTIR analysis showed that PHBV/P3/4HB blend films would maintain the helical structure, similar to pure PHBV. Meanwhile, with increasing P3/4HB content, the inter‐ and intra‐interactions of PHBV and P3/4HB decrease gradually. Besides, a lower elastic modulus and a higher elongation at break were obtained, which show that the addition of P3/4HB would make the brittle PHBV to ductile materials. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Processability modifications of poly(3‐hydroxybutyrate) by plasticizing,blending, and stabilizing

Poly(3‐hydroxybutyrate) (PHB) was plasticized with dioctyl (o‐)phthalate, dioctyl sebacate, and acetyl tributyl citrate (ATBC). The thermal properties, mechanical properties, and melt flow ability were studied with differential scanning calorimetry, thermogravimetric analysis, a universal material testing machine, and a melt flow indexer. ATBC was revealed to be an efficient plasticizer, reducing the glass‐transition temperature and increasing the thermoplasticization ability of PHB. We also blended poly(3‐hydroxybutyrate‐co‐hydroxyhexanoate) (PHBHHx) and poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) [P(3/4HB)] with PHB, ATBC, and antioxidant 1010 to overcome the brittleness of PHB and improve the melt flow stability of the materials. PHBHHx did little to improve the thermal processing but increased the fluidity of PHB, and P(3/4HB) toned the toughness of PHB. The addition of antioxidant 1010 enhanced the thermal stabilization of PHB. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Study on short glass fiber‐reinforced poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) composites

Biobased non‐fossil polyester poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P3/4HB) containing 4.0 mol % 4‐hydroxybutyrate (4HB) was melt‐mixed with short glass fibers (SGF) via a co‐rotating twin‐screw extruder. The compositing conditions, average glass fiber length and distribution, thermal, crystallization, and mechanical properties of the P3/4HB/SGF composites were investigated. Calcium stearate, two kinds of paraffin wax and modified ethylene bis‐stearamide (TAF) were investigated as lubricants for the P3/4HB/SGF composites. It revealed that TAF is the most efficient lubricant of the P3/4HB/SGF composites. Coupling agents 2,2′‐(1,3‐phenylene)bis‐2‐oxazoline (1,3‐PBO) and pyromellitic dianhydride (PMDA) were used as end‐group crosslinkers to reduce the degradation of P3/4HB and increase the mechanical properties of the P3/4HB/SGF composites. It showed that 1,3‐PBO is the efficient coupling agent. The optimum condition of the P3/4HB/SGF composites is 1.5 phr TAF, 1.0 phr 1,3‐PBO, and 30 wt % glass fiber content. And the maximum of tensile strength, tensile modulus, and impact strength of the composites is 3.7, 6.6, 1.8 times of the neat P3/4HB polymer, respectively. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of nucleation agents on the crystallization of poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P3/4HB)

Boron nitride (BN), talc, hydroxyapatite (HA), and zinc stearate (ZnSt) were investigated as nucleation agents (NA) for nonfossil‐based poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P3/4HB) plastics. Nonisothermal crystallization behaviors of the P3/4HB/NA blends were examined by DSC. It revealed that BN is the most efficient nucleation agent to promote the crystallization rate, however, but not the crystallization degree. The lasting crystallization of P3/4HB was also removed. The nucleation effect was strengthened with increase of BN content up to 1% and then slackened deeply when further BN was added. Isothermal crystallization analysis revealed that the addition of nucleation agent BN does not alter the crystal growth mode of P3/4HB, with maintaining the Avrami parameter n value around 2.40. Talc did enhance the crystallization of P3/4HB with however milder crystal growth rate. HA and ZnSt did not promote, but depressed the crystallization of P3/4HB plastics. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Improvement of the production of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate‐co‐4‐hydroxybutyrate) terpolyester by manipulating the culture condition

BACKGROUND: The aim of this work is to enhance the production of terpolyester poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate‐co‐4‐hydroxybutyrate) (P(3HB‐co‐3HV‐co‐4HB)) produced by a locally isolated bacterium, Cupriavidus sp. USMAA2‐4. The monomer composition was varied by supplementing different carbon precursors and by manipulating the culture condition through one‐stage cultivation. The effect of C/N ratio and different concentrations of carbon source and precursors were investigated in order to produce higher content of this terpolyester. Although research on this biodegradable polyester is abundant, studies on terpolyester P(3HB‐co‐3HV‐co‐4HB) are still limited. RESULTS: Supplementation of oleic acid in accumulation medium increased the bacterial growth and polyhydroxyalkanoate (PHA) accumulation. It was also shown that medium consisting of assorted carbon precursors at C/N 20 gave relatively high dry cell weight and P(3HB‐co‐3HV‐co‐4HB) content. Various compositions of terpolyester were obtained when the concentration of oleic acid and 4HB precursors were manipulated. The combination of oleic acid with γ‐butyrolactone and 1‐pentanol was found to be the best combination to produce high PHA content (81 wt%). The composition of monomer in P(3HB‐co‐3HV‐co‐4HB) was produced in the range 8–13 mol% for 3HV and 9–24 mol% for 4HB, respectively. CONCLUSIONS: The production of P(3HB‐co‐3HV‐co‐4HB) in shake‐flasks successfully produced 81 wt% of PHA content. This manipulated culture condition can be used at larger scale to provide modeling for the production of terpolyester in a bioreactor. Copyright © 2012 Society of Chemical Industry     

Miscibility and crystallization kinetics of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/ poly(methyl methacrylate) blends

The miscibility and crystallization kinetics of the blends of random poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [P(HB‐co‐HV)] copolymer and poly(methyl methacrylate) (PMMA) were investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that P(HB‐co‐HV)/PMMA blends were miscible in the melt. Thus the single glass‐transition temperature (T_g) of the blends within the whole composition range suggests that P(HB‐co‐HV) and PMMA were totally miscible for the miscible blends. The equilibrium melting point (T°_m) of P(HB‐co‐HV) in the P(HB‐co‐HV)/PMMA blends decreased with increasing PMMA. The T°_m depression supports the miscibility of the blends. With respect to the results of crystallization kinetics, it was found that both the spherulitic growth rate and the overall crystallization rate decreased with the addition of PMMA. The kinetics retardation was attributed to the decrease in P(HB‐co‐HV) molecular mobility and dilution of P(HB‐co‐HV) concentration resulting from the addition of PMMA, which has a higher T_g. According to secondary nucleation theory, the kinetics of spherulitic crystallization of P(HB‐co‐HV) in the blends was analyzed in the studied temperature range. The crystallizations of P(HB‐co‐HV) in P(HB‐co‐HV)/PMMA blends were assigned to n = 4, regime III growth process. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3595–3603, 2004     

Miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/poly(vinyl acetate) blends

The miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (P(HB‐co‐HV))/poly(vinyl acetate) (PVAc) blends have been investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that P(HB‐co‐HV)/PVAc blends were miscible in the melt over the whole compositions. Thus the blend exhibited a single glass transition temperature (T_g), which increased with increasing PVAc composition. The spherulitic morphologies of P(HB‐co‐HV)/PVAc blends indicated that the PVAc was predominantly segregated into P(HB‐co‐HV) interlamellar or interfibrillar regions during P(HB‐co‐HV) crystallization because of the volume‐filled spherulites. As to the crystallization kinetics study, it was found that the overall crystallization and crystal growth rates decreased with the addition of PVAc. The kinetics retardation was primarily attributed to the reduction of chain mobility and dilution of P(HB‐co‐HV) upon mixing with higher T_g PVAc. The overall crystallization rate was predominantly governed by the spherulitic growth rate and promoted by the samples treated with the quenched state because of the higher nucleation density. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 980–988, 2006     

Study of miscibility,crystallization, mechanical properties,and thermal stability of blends of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)

Natural amorphous polymer poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P3HB4HB) containing 41 mol % of 4HB was blended with poly(3‐hydroxybutyrate) (PHB) with an aim to improve the properties of PHB. The influence of P3HB4HB contents on thermal and mechanical properties of the blends was evaluated with differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy, stress–strain measurement and thermo gravimetric analyzer. Miscibility of PHB/P3HB4HB blends was mainly decided by the contents of P3HB4HB. When P3HB4HB exceeded 50 wt %, the two polymer phases separated and showed immiscibility. The addition of P3HB4HB did not alter the crystallinity of PHB, yet it diluted the PHB crystalline phase as revealed by DSC studies. DSC and FTIR results showed that the overall crystallinity of the blends decreased remarkably with increasing of P3HB4HB contents. Decreased glass transition temperature and crystallinity imparted desired flexibility for the blends. The ductility of the blends increased progressively with increasing of P3HB4HB content. Thus, the PHB mechanical properties can be modulated by changing the blend composition. P3HB4HB did not significantly improve the thermal stability of PHB, yet it is possible to melt process PHB without much molecular weights loss via blending it with suitable amounts of P3HB4HB. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Tailoring the surface architecture of poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) scaffolds

This study was designed to determine whether the surface modifications of the various poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) [P(3HB‐co‐4HB)] copolymer scaffolds fabricated would enhance mouse fibroblast cells (L929) attachment and proliferation. The P(3HB‐co‐4HB) copolymer with a wide range of 4HB monomer composition (16–91 mol %) was synthesized by a local isolate Cupriavidus sp. USMAA1020 by employing the modified two‐stage cultivation and by varying the concentrations of 4HB precursors, namely γ‐butyrolactone and 1,4‐butanediol. Five different processing techniques were used in fabricating the P(3HB‐co‐4HB) copolymer scaffolds such as solvent casting, salt‐leaching, enzyme degradation, combining salt‐leaching with enzyme degradation, and electrospinning. The increase in 4HB composition lowered melting temperatures (T_m) but increased elongation to break. P(3HB‐co‐91 mol % 4HB) exhibited a melting point of 46°C and elongation to break of 380%. The atomic force analysis showed an increase in the average surface roughness as the 4HB monomer composition increased. The mouse fibroblasts (L929) cell attachment was found to increase with high 4HB monomer composition in copolymer scaffolds. These results illustrate the importance of a detailed characterization of surface architecture of scaffolds to provoke specific cellular responses. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Hydrogen bonding,miscibility, crystallization,and thermal stability in blends of biodegradable polyhydroxyalkanoates and polar small molecules of 4‐tert‐butylphenol

The hydrogen bonding, miscibility, crystallization, and thermal stability of poly(3‐hydroxybutyrate) (PHB)/4‐tert‐butylphenol (BOH) blends and poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) [P(3HB‐3HHx)]/BOH blends were investigated by Fourier transform infrared (FTIR) spectroscopy, solid‐state¹³C‐NMR, differential scanning calorimetry, wide‐angle X‐ray diffraction (WAXD), and thermogravimetric analysis. The results of FTIR spectroscopy and solid‐state¹³C‐NMR show that intermolecular hydrogen bonds existed between the two components in the blends and that the interaction was caused by the carbonyl groups in the amorphous phase of both polyesters and the hydroxyl groups of BOH. With increasing BOH content, the chain mobility of both the PHB and P(3HB‐3HHx) components was improved. After the samples were quenched, the detected single glass‐transition temperatures decreased with composition, indicating that both PHB/BOH and P(3HB‐3HHx)/BOH were miscible blends in the melt. Moreover, as BOH content increased, the melting temperatures of PHB and P(3HB‐3HHx) clearly decreased, which implied that their crystallization was suppressed by the addition of BOH. Although the crystallinity of PHB and P(3HB‐3HHx) components decreased with increasing BOH content in the blends, their crystal structures were hardly affected after they were blended with BOH, which was further proven by WAXD results. In addition, the thermal stability of PHB was improved by a smaller amount of BOH.     

Study on the poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)‐based nanocomposites reinforced by surface modified nanocrystalline cellulose

As a kind of reinforcing agent, the application of nanocrystalline cellulose (NCC) is widely limited in hydrophobic polymers owing to its rich hydroxyl surface. In this study, NCC was modified with lauric acid/p‐toluensulfonyl chloride mixture, then the modified nanocrystalline cellulose (mNCC) was incorporated into biopolyester poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P(3,4)HB) by solution casting to prepare P(3,4)HB/mNCC nanocomposites. The prepared mNCC and P(3,4)HB/mNCC nanocomposites were characterized by Fourier transform‐infrared, X‐ray diffraction, contact angle test, transmission electron microscopy, scanning electron microscopy, differential scanning calorimetric, polarized optical microscope, dynamic mechanical analysis, and thermogravimetric analysis. The results show that the crystallinity and mechanical properties of P(3,4)HB are greatly improved due to the fact that NCC can be modified successfully and the mNCC can distribute uniformly in nanoscale in the matrix with good compatibility along the interface. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2015–2022, 2013     

Biodegradation of poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) by a novel P3/4HB depolymerase purified from Agrobacterium sp. DSGZ

A poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P3/4HB)‐degrading strain, Agrobacterium sp. DSGZ, was isolated from sewage by poly(3‐hydroxybutyrate) (PHB) mineral agar plates. A novel P3/4HB depolymerase with a molecular weight of 34 kDa was purified through a novel single‐step affinity chromatography method from the culture supernatant of the strain by using P3/4HB powder as a substrate. The purified depolymerase showed optimum activity at pH 7.0 and 50°C, and was stable at the pH range of 6.0 to 9.0 and temperature below 50°C. Enzyme activity was strongly inhibited by phenylmethylsulfonyl fluoride (PMSF), ethylenediaminetetraacetic acid (EDTA), hydrophobic reagents, and some metal ions. The depolymerase degraded poly(3‐hydroxybutyrate) (PHB), poly(hydroxybutyrate‐co‐hydroxyvalerate) (PHBV), P3/4HB, and polycaprolactone (PCL), instead of polylactic acid (PLA) or poly(butylene succinate) (PBS). Meanwhile, the depolymerase showed high hydrolytic activity against short‐chain length esters, such as butyrate acid ester and caprylic acid ester. The main degradation products of the depolymerase were identified as hydroxybutyrate monomers and dimers, and the monomers were identified as 3‐hydroxybutyrate (3HB) monomers and 4‐hydroxybutyrate (4HB) monomers. The preparation procedure, crystallinity, and 4HB composition of the P3/4HB copolymer showed evident effect on degradation behavior, and change in crystallinity was the main factor affecting degradation. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42805.