Preparation of poly(tert‐butyl acrylate)‐poly(acrylic acid) amphiphilic copolymers via radiation‐induced reversible addition–fragmentation chain transfer mediated polymerization of tert‐butyl acrylate

Poly(tert‐butyl acrylate) (PtBA) is a versatile hydrophobic macromolecule usually preferred in the development of new materials for a host of applications. PtBA homopolymers with well‐defined structure and controlled molecular weight in a wide range were successfully synthesized via radiation‐induced reversible addition–fragmentation chain transfer (RAFT) polymerization in the presence of a trithiocarbonate type RAFT agent. The polymerization of tBA was performed under ⁶⁰Co γ‐irradiation in the presence of 2‐(dodecylthiocarbonothioylthio)‐2‐methylpropionic acid (DDMAT) as the RAFT agent in toluene at room temperature with three [tBA]/[DDMAT] ratios (400, 600 and 1000) and different irradiation times. Radiation‐induced polymerization of tBA displayed controlled free radical polymerization characteristics: a narrow molecular weight distribution (M_w/M_n ~ 1.1), pseudo first order kinetics and controlled molecular weights. The system followed the RAFT polymerization mechanism even at very low amounts of RAFT agent ([tBA]/[DDMAT] = 1000), and molecular weights up to 113 900 with narrow dispersity (Ð =1.06) were obtained. PtBA was further hydrolysed into different amphiphilic PtBA‐co‐poly(acrylic acid) (PAA) copolymers by low (27.5%) and high (77.3%) degrees of hydrolysis. The pH sensitivity of the two copolymers was investigated by dynamic light scattering at pH 2 and pH 9 (above and below the pK_a value of PAA) and their hydrodynamic diameters and zeta potential values were determined. © 2020 Society of Chemical Industry     

Atom transfer radical polymerization grafting of highly functionalized polystyrene and poly(4‐methylstyrene) macroinitiators with tert‐butyl acrylate

Two monodisperse graft copolymers, poly(4‐methylstyrene)‐graft‐poly(tert‐butyl acrylate) [number‐average molecular weight (M_n) = 37,500, weight‐average molecular weight/number‐average molecular weight (M_w/M_n) = 1.12] and polystyrene‐graft‐poly(tert‐butyl acrylate) (M_n = 72,800, M_w/M_n = 1.12), were prepared by the atom transfer radical polymerization of tert‐butyl acrylate catalyzed with Cu(I) halides. As macroinitiators, poly{(4‐methylstyrene)‐co‐[(4‐bromomethyl)styrene]} and poly{styrene‐co‐[4‐(1‐(2‐bromopropionyloxy)ethyl)styrene]}, carrying 40% of the bromoalkyl functionalities along the chain, were used. The dependencies of molecular parameters on monomer conversion fulfilled the criteria for controlled polymerizations. In contrast, the dependencies of monomer conversion versus time were nonideal; possible causes were examined. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2930–2936, 2002     

Rapid ambient temperature atom transfer radical polymerization of tert‐butyl acrylate

BACKGROUND: Atom transfer radical polymerization (ATRP) is considered to be one of the better and easier synthetic tools for the preparation of polymers with controlled molecular weights and polydispersities. Ambient temperature ATRP of tert‐butyl acrylate (tBA) was studied in a detailed manner with ethyl 2‐bromoisobutyrate (EBrB) and tert‐butyl 2‐bromoisobutyrate (tBuBrB) as the initiators for three different degrees of polymerization. RESULTS: Details pertaining to the kinetics of polymerization using different initiators are reported. It is observed that dimethylsulfoxide accelerates the polymerization at room temperature. The use of Cu(II) as the deactivator produces very narrow dispersity polymers. A diblock copolymer, poly(tert‐butyl acrylate)‐block‐poly(methyl methacrylate), was synthesized from the poly(tBA) macroinitiator demonstrating the controlled living nature of the polymerizations. CONCLUSIONS: The rate of polymerization is more rapid with a secondary initiator (ethyl 2‐bromopropionate) compared to the tertiary initiators EBrB and tBuBrB. From the detailed kinetic results it is observed that tris(2‐dimethylaminoethyl)amine was a better ligand compared to tris(2‐aminoethyl)amine in terms of achieving controlled polymerization. Copyright © 2007 Society of Chemical Industry     

Amphiphilic diblock and ABC triblock methacrylate copolymers: synthesis and aqueous solution characterization

Three isomeric, linear, equimolar, amphiphilic ABC triblock copolymers comprising methyl methacrylate (MMA, nonionic hydrophobic), 2-(dimethylamino)ethyl methacrylate, (DMAEMA, ionizable hydrophilic) and hexa(ethylene glycol) methacrylate (HEGMA, nonionic hydrophilic) units (10 units in each block) were synthesized by group transfer polymerization (GTP). These were the three block sequence isomers, ABC, ACB and BAC. The corresponding random terpolymer was also prepared. The molecular weights and compositions of all the polymers were characterized by GPC and ¹H NMR. Measurements of the hydrodynamic diameters and cloud points of the copolymers in aqueous solution suggest that the various distributions of monomer units in the four terpolymers (the three triblocks and the random) result in different supramolecular structures with different colloidal stabilities.     

Low molecular weight block copolymers as plasticizers for polystyrene

Polystyrene‐b‐alkyl, polystyrene‐b‐polybutadiene‐b‐polystyrene, and polystyrene‐b‐poly(propylene glycol)monotridecyl ether were synthesized using macro initiators and atom transfer radical polymerization or by esterifications of homopolymers. The aim was a maximum molecular weight of 4 kg/mol and minimum polystyrene content of 50 w/w %, which by us is predicted as the limits for solubility of polystyrene‐b‐alkyl in polystyrene. DSC showed polystyrene was plasticized, as seen by a reduction in glass transition temperature, by block copolymers consisting of a polystyrene block with molecular weight of approximately 1 kg/mol and an alkyl block with a molecular weight of approximately of 0.3 kg/mol. The efficiency of the block copolymers as plasticizers increases with decreasing molecular weight and polystyrene content. In addition, polystyrene‐b‐alkyl is found to be an efficient plasticizer also for polystyrene‐b‐polyisoprene‐b‐polystyrene (SIS) block copolymers. The end use properties of SIS plasticized with polystyrene‐b‐alkyl, measured as tensile strength, is higher than for SIS plasticized with dioctyl adipate. The polystyrene‐b‐polybutadiene‐b‐polystyrene and polystyrene‐b‐poly(propylene glycol)monotridecyl ether series were only partially soluble in polystyrene and insoluble in the polystyrene phase of SIS. For the lowest molecular weight samples, this leads to measurable plasticization of polystyrene but no plasticization of SIS. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 981–991, 2005     

Novel microporous poly(vinylidene fluoride)‐graft‐poly(tert‐butyl acrylate) electrolytes for secondary lithium batteries

BACKGROUND: Much interest has recently been shown in improving the performance of lithium‐ion polymer batteries with gel polymer electrolytes (GPEs) due to a rapid expansion in industrial demand. Novel GPEs based on poly(vinylidene fluoride)‐graft‐poly(tert‐butyl acrylate) (PVDF‐g‐tBA) microporous mats are suggested in this study. RESULTS: Microfibrous polymer electrolytes were prepared using electrospinning and characterized for extent of grafting, morphology, crystallinity, electrochemical stability, ionic conductivity, interfacial resistance and cell cycleability. The degree of crystallinity was lower for tBA‐grafted PVDF mats than that of neat PVDF. The PVDF‐g‐tBA showed an improvement in the ionic conductivity, electrochemical stability, interfacial resistance and cyclic performance. CONCLUSION: The tBA‐grafted PVDF microporous electrolytes are promising candidates for enhancing the performance of lithium‐ion polymer batteries. Copyright © 2008 Society of Chemical Industry     

Synthesis of diblock and triblock copolymers from butyl acrylate and styrene by reverse iodine transfer polymerization

Well‐defined AB and BA diblock copolymers were obtained by a one‐pot two‐step sequential block copolymerization by reverse iodine transfer polymerization (RITP), A being a poly(styrene) block and B a poly(butyl acrylate) block. High monomer conversions during the formation of the first block avoided the purification steps before growing the second block. In a third sequential step, the diblock copolymers were further extended to synthesize ABA and BAB triblock copolymers. Furthermore, the synthesis of ABA and BAB copolymers in only two steps by RITP was investigated starting with the formation of the central block using 2,5‐di(2‐ethylhexanoylperoxy)‐2,5‐dimethylhexane as a difunctional initiator and then resuming the polymerization to grow the external blocks in a second step. The obtained copolymers were analyzed by size exclusion chromatography, transmission electron microscopy, and differential scanning calorimetry. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Graft copolymerization of methyl acrylate onto silk sericin initiated by tert‐butyl hydroperoxide

A novel redox system, tert‐butyl hydroperoxide (TBHP)–silk sericin (SS), was used to initiate the graft copolymerization of methyl acrylate (MA) onto silk sericin in an aqueous medium. The graft copolymer, consisting of nanoparticles with a fine core–shell structure, was characterized using Fourier transfer infrared spectroscopy. The effects of the concentrations of MA and TBHP, reaction temperature and time on the grafting parameters of the copolymerization were studied in detail. In terms of grafting percentage and grafting efficiency, the optimum reaction conditions were obtained as follows: [MA] = 0.465 mol L^?1, [TBHP] = 3.884 × 10^?4 mol L^?1, T = 80 °C, t = 150 min. Transmission electron microscopy images of the particles showed a core–shell morphology, where poly(methyl acrylate) cores were covered with SS shells. A possible initiation mechanism is proposed. Copyright © 2006 Society of Chemical Industry     

Production,cellular structure and thermal conductivity of microcellular (methyl methacrylate)–(butyl acrylate)–(methyl methacrylate) triblock copolymers

Microcellular foaming of a (methyl methacrylate)–(butyl acrylate)–(methyl methacrylate) triblock copolymer was carried out by means of supercritical CO₂ in a single‐step process. The experiments were performed at 40 °C using a pressure of 300 bar (30 MPa) during 24 h. The depressurization times were modified from 2 to 30 min, leading to cell sizes from 10 to 100 µm, and relative densities from 0.11 to 0.17. It was found that the key parameter to control cell size and density was depressurization time: longer depressurization times generated larger cell sizes and lower densities. The thermal conductivity of these materials was measured using the transient plane source technique, and it was found that this decreased as the density was reduced. Various models for the prediction of thermal conductivity by conduction were tested. It was found that all the models underestimated the experimental results due to a significant contribution of radiation heat flow for these materials. Copyright © 2010 Society of Chemical Industry     

New chemoenzymatic‐facilitated synthesis of diblock copolymers and biomedically appropriate vesicles

BACKGROUND: Biocatalytic approaches in polymer science are expected to further increase the diversity of polymeric materials. And the full exploitation of biocatalysis in polymer science will require the development of compatible chemoenzyme‐catalyzed methods. RESULTS: The well‐defined diblock copolymer poly(2,2,2‐trichloroethanol 10‐hydroxydecanate)‐block‐poly(glycidyl methacrylate) (P(TCE‐10‐HD)‐b‐PGMA) was obtained by combining enzymatic condensation polymerization and atom transfer radical polymerization (ATRP). P(TCE‐10‐HD) was prepared by enzymatic condensation polymerization of 10‐hydroxydecanoic acid and 2,2,2‐trichloroethanol. This ? CCl₃‐terminated polyester permitted subsequent ATRP of glycidyl methacrylate. Kinetic studies indicated a ‘living’ controlled radical polymerization. The self‐assembly behavior of the amphiphilic diblock copolymer, in tetrahydrofuran/water, gave rise to aggregates with diameters ranging from 160 to 240 nm. The morphology of the assembly particles was studied using atomic force microscopy, transmission electron microscopy and scanning electron microscopy. CONCLUSION: To obtain the ATRP macromolecular initiator, this one‐step method is more convenient than other two‐step methods. The results of NMR, Fourier transform infrared and gel permeation chromatography analyses testified that this method is feasible. The formulated vesicles have great potential as biomedical materials. Copyright © 2008 Society of Chemical Industry     

Controlled one-pot synthesis of pH-sensitive self-assembled diblock copolymers and their aggregation behavior

Diblock copolymers of t-butyl methacrylate (tBMA) and 2-(diethylamino)ethyl methacrylate (DEAEMA) were successfully synthesized by one-pot strategy via the atom transfer radical polymerization (ATRP). Kinetic results clearly demonstrated the controlled/‘living’ character of the polymerization. The zwitterionic block copolymers of poly(methacrylic acid-b-DEAEMA), obtained by hydrolysis of poly(tBMA-b-DEAEMA), showed pH-dependent reverse micellization behavior. Micellar aggregates formed from poly(MAA₃₀-b-DEAEMA₇₁), poly(MAA₆₈-b-DEAEMA₅₅) and poly(MAA₆₄-b-DEAEMA₄₄) had fairly low polydispersity index at both solutions of low pH of 2 and high pH of 12. Micelles formed at pH 2 were larger (R_h∼40-61 nm) with looser core due to hydration of the MAA. In the presence of simple electrolyte (0.3 mol dm⁻³ NaCl solution), the size of the micelles reduced by almost half while the aggregation number was little changed. This is attributed to the draining of the hydrated micellar core due to osmotic pressure. On the other hand, DEAEMA-core micelles formed at pH 12 were compact and much smaller (R_h∼14-22 nm). Addition of NaCl had only a small effect. The micellar size reduced only slightly due to the electrostatic screening effect and the aggregation number was almost unchanged.     

Amphiphilic diblock copolymers containing poly(N‐hexylisocyanate): Monolayer behavior at the air–water interface

The behavior of amphiphilic diblock copolymers containing 80–89% of poly(N‐hexylisocyanate) (PHIC) with different hydrophobic segments spread at the air–water interface has been studied. Surface pressure‐area isotherms (π‐A) at the air–water interface were determined. It was found that these diblock copolymers form stable monolayers and the isotherms present a pseudoplateau region at low surface pressure, irrespective of the nature of the partner block: poly(styrene) (PS) or poly(isoprene). Surface pressure variation at the semidilute region of the monolayer was expressed in terms of the scaling laws as power function of the surface concentration. The critical exponents of the excluded volume ν obtained for copolymers with PHIC and PS blocks are 0.58 for the copolymer with 85% of PHIC and 15% of PS, and 0.63 for the copolymer with 89% of PHIC and 11% of PS. The hydrophobicity degree of the diblock copolymers was estimated from the determination of the surface energy values by wettability measurements. The morphology of the monolayers was determined by means of Brewster angle microscopy. Molecular dynamic simulation was performed to explain the experimental behavior of diblock copolymers at the air–water interface. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Study of novel biodegradable thermo‐sensitive hydrogels of methoxy‐poly(ethylene glycol)‐block‐polyester diblock copolymers

A series of biodegradable thermo‐sensitive hydrogels were synthesized by ring‐opening polymerization of methoxy‐poly(ethylene glycol) (mPEG) and various ester monomers, i.e. D ,L ‐lactide, glycolide, β‐propiolactone, δ‐valerolactone and ε‐caprolactone. The copolymers were characterized using ¹H NMR spectroscopy and gel permeation chromatography. The micelle properties were also measured. The results indicated that the diblock copolymers formed nano‐micelles at low concentrations in aqueous phase. The lower critical solution temperatures of the diblock copolymers were above 35 °C at 1 wt%. As the temperature increased above room temperature, the diblock copolymer solutions underwent a sol‐to‐gel phase transition, which was manifested in viscosity increases, indicative of the formation of a gel. The mPEG–polyester diblock copolymer solutions exhibited sol‐gel transition behavior as a function of temperature and polymer concentration. Copyright © 2010 Society of Chemical Industry     

Micellization of pH‐sensitive poly(butadiene)‐block‐poly(2 vinylpyridine)‐block‐poly(ethylene oxide) triblock copolymers: Complex formation with anionic surfactants

The micellization of three tailor‐made triblock copolymers, such as PB₁₀₀–P2VP₁₀₀–PEO₁₀₄, PB₁₈₅–P2VP₁₀₈–PEO₁₅₄, and PB₃₇–P2VP₁₁₅–PEO₂₄₁, having similar total molecular weights and constant poly(2‐vinylpyridine) (P2VP) sequence lengths, was investigated as a function of pH and sodium dodecyl sulfate (SDS) concentration. At pH 7 the formation of intermicellar aggregates was observed, especially for copolymers of low poly(ethylene oxide) (PEO) content. A pH decrease from 7 to 3 leads to a particle size increase due to the electrostatic repulsion of the protonated P2VP chains. The influence of the PEO sequence length was also observed for zeta potential values. At pH 3, in the absence of SDS, core–shell–corona micelles are formed whereas in the presence of small amount of SDS (degree of neutralization DN = 0%–50%), a complex is formed between SDS and the protonated P2VP which leads to the shrinkage of the shell and thus to a decrease of the micellar sizes. For higher DN values, the micellar sizes increase due to the formation of large agglomerates and a transition occurs from a monomodal to a bimodal size distribution. Furthermore, it turned out that secondary aggregation, such as intermicellar aggregation, can completely be avoided if the degree of polymerization (DPn) of the water‐soluble block is significantly higher than the DPn of the water‐insoluble sequence. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45313.     

Atomic force microscopy study of self‐assembly behaviors of hydrophobic poly(n‐butyl methacrylate)‐block‐polydimethylsiloxane‐block‐poly(n‐butyl methacrylate) ABA triblock copolymers

Poly(n‐butyl methacrylate)‐block‐polydimethylsiloxane‐block‐poly(n‐butyl methacrylate) (PBMA‐block‐PDMS‐block‐PBMA) ABA triblock copolymers were synthesized successfully via atom‐transfer radical polymerization using PDMS as macroinitiator. The effects of PDMS content and substrate nature on self‐assembly behaviors of PBMA‐block‐PDMS‐block‐PBMAs were systematically studied using atomic force microscopy. Two series of triblock copolymers with different molecular weights and compositions, i.e. PBMA‐block‐PDMSA12‐block‐PBMAs and PBMA‐block‐PDMSA21‐block‐PBMAs, were used, where the latter were of a higher PDMS content than the former. On silicon wafer, it was found that only spherical structures formed after annealing films spin‐coated from chloroform solutions of PBMA‐block‐PDMSA12‐block‐PBMAs. In contrast, films of PBMA‐block‐PDMSA21‐block‐PBMAs formed semi‐continuous structures. On mica wafer, it was found that ordered cylindrical pores formed after annealing films spin‐coated from chloroform solutions of PBMA‐block‐PDMSA12‐block‐PBMAs. In contrast, films of PBMA‐block‐PDMSA21‐block‐PBMAs formed isolated cylinders or worm‐like morphologies. Copyright © 2011 Society of Chemical Industry     

Synthesis and characterization of poly(n‐butyl methacrylate)‐b‐polystyrene diblock copolymers by atom transfer radical emulsion polymerization

Poly(n‐butyl methacrylate) (PBMA)‐b‐polystyrene (PSt) diblock copolymers were synthesized by emulsion atom transfer radical polymerization (ATRP). PBMA macroinitiators that contained alkyl bromide end groups were obtained by the emulsion ATRP of n‐butyl methacrylate with BrCH₃CHCOOC₂H₅ as the initiator; these were used to initiate the ATRP of styrene (St). The latter procedure was carried out at 85°C with CuCl/4,4′‐di(5‐nonyl)‐2,2′‐bipyridine as the catalyst and polyoxyethylene(23) lauryl ether as the surfactant. With this technique, PBMA‐b‐PSt diblock copolymers were synthesized. The polymerization was nearly controlled; the ATRP of St from the macroinitiators showed linear increases in number‐average molecular weight with conversion. The block copolymers were characterized with IR spectroscopy, ¹H‐NMR, and differential scanning calorimetry. The effects of the molecular weight of the macroinitiators, macroinitiator concentration, catalyst concentration, surfactant concentration, and temperature on the polymerization were also investigated. Thermodynamic data and activation parameters for the ATRP are also reported. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2123–2129, 2005     

Versatile synthesis of self‐assembling ABA triblock copolymers with polymethyloxazoline A‐blocks and a polysiloxane B‐block decorated with supramolecular receptors

BACKGROUND: Self‐assembling amphiphilic block copolymers with incorporated, biologically relevant functionalities have received limited attention, partly due to the fact that biomolecules are not robust enough to synthetic manipulation, do not lend themselves readily to systematic studies due to their complexity and leach rather quickly from a vesicle or membrane when physically incorporated. Synthetic supramolecules are used as biomolecule mimics in functional membranes. RESULTS: Reaction conditions were established for the synthesis of a tosyl‐terminated siloxane end‐blocker, which serves as molecular weight control in the synthesis of polydimethylsiloxane (PDMS) and poly(dimethylsiloxane‐co‐methylhydrosiloxane) [P(DMS‐co‐MHS)] copolymers. Hydrosilylation reactions were investigated for the covalent coupling of synthetic supramolecules (18‐crown‐6 ether, hydroxybenzoate) to the polymer backbone using the methylhydrosiloxane repeat units as the anchor moiety. Using P(DMS‐co‐MHS) or derivatized P(DMS‐co‐MHS) copolymers as macroinitiator for the ring‐opening polymerization of 2‐methyl‐4‐hydroxy‐oxazoline led to the formation of poly[(dimethylsiloxane‐co‐methylhydrosiloxane)‐block‐oxazoline] [P(DMS‐co‐MHS‐b‐Ox)] ABA triblock copolymers with defined PDMS to PMHS ratios and controlled molecular weights. CONCLUSION: Derivatized P(DMS‐co‐MHS‐b‐Ox) ABA triblock copolymers synthesized using a novel versatile procedure undergo vesicle formation upon electroformation with vesicle diameters ranging from 2 to 10 µm. The size of the vesicle depends on the overall polarity of the macromolecule. Copyright © 2008 Society of Chemical Industry     

ABA triblock copolymers from poly(p‐dioxanone) and poly(ethylene glycol)

Poly(p‐dioxanone)–poly(ethylene glycol)–poly(p‐dioxanone) ABA triblock copolymers (PEDO) were synthesized by ring‐opening polymerization from p‐dioxanone using poly(ethylene glycol) (PEG) with different molecular weights as macroinitiators in N₂ atmosphere. The copolymer was characterized by ¹H NMR spectroscope. The thermal behavior, crystallization, and thermal stability of these copolymers were investigated by differential scanning calorimetry and thermogravimetric measurements. The water absorption of these copolymers was also measured. The results indicated that the content and length of PEG chain have a greater effect on the properties of copolymers. This kind of biodegradable copolymer will find a potential application in biomedical materials. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:1092–1097, 2006     

Thermoreversible gelation of mixed triblock and diblock copolymers in n-octane

The thermoreversible gelation of blends of polystyrene-block-poly(ethylene/butylene)-block-polystyrene (SEBS) and polystyrene-block-poly(ethylene/propylene) (SEP) copolymers in n-octane was studied. The solvent is selective for the polyolefine blocks of the copolymers. The influence of the composition of the hybrid gels on the sol-gel transition and on the mechanical properties of the gels was analyzed. The sol-gel transition temperature increased with the concentration of both type of copolymers and did not depend on the hybrid gel composition for SEBS2 proportions higher than 50% at a total copolymer concentration higher than 6 wt%. The mechanical properties of the different gels were examined through oscillatory shear and compressive stress relaxation measurements. The elastic storage modulus increased with the triblock copolymer concentration but kept almost constant with the diblock copolymer concentration for SEBS concentrations higher than 5.0%. The stress relaxation rate was not dependent on the concentration of triblock and diblock copolymers, but the hybrid gels show lower stress relaxation rates than the pure SEBS2 gels. In the hybrid SEBS/SEP gels the SEP chains impart stability to the micelles or nodes of the network whereas the SEBS chains are responsible for the bridges that keep the gel as one-phase system.     

Swelling behavior of gelatin‐g‐poly(butyl acrylate) copolymers

Gelatin‐g‐poly (butyl acrylate) copolymers were prepared with gelatin and butyl acrylate. The effects of various reaction parameters, including the concentration of the monomer, the concentration of the initiator, the concentration of gelatin, the reaction time, and the temperature, on the swelling behavior were studied systematically. In addition, the effect of the intercalation of graft copolymers with montmorillonite on the swelling behavior was investigated. The results indicated that the graft copolymerization and intercalation with montmorillonite could greatly reduce the swelling degree of gelatin. The swelling process of the copolymers followed second‐order kinetics identical to those of the original gelatin. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1033–1037, 2005