Effect of monomer composition on properties of copolyimides derived from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride/4,4′‐oxydianiline/1,3‐bis (4‐aminophenoxy)benzene

A series of uncontrolled molecular weight homopolyimides and copolyimides based on 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (s‐BPDA)/4,4′‐oxydianiline (4,4′‐ODA)/1,3‐bis(4‐aminophenoxy)benzene (TPER) were synthesized. All the polyimides displayed excellent thermal stability and mechanical properties, as evidenced by dynamic thermogravimetric analysis and tensile properties testing. A singular glass transition temperature (T_g) was found for each composite from either differential scanning calorimetry (DSC) or dynamic mechanical analysis (DMA), but the values determined from tan δ of DMA were much different from those determined from DSC and storage modulus (E′) of DMA. The Fox equation was used to estimate the random T_g values. Some composites exhibited re‐crystallization after quenching from the melt; upon heating, multi‐melting behavior was observed after isothermal crystallization at different temperatures. The equilibrium melting temperature was estimated using the Hoffman‐Weeks method. Additionally, DMA was conducted to obtain E′ and tan δ. Optical properties were strongly dependent on the monomer composition as evidenced by UV‐visible spectra. X‐ray diffraction was used to interpret the crystal structure. All the results indicated that composites with TPER composition ≥ 70% were dominated by the TPER/s‐BPDA polyimide phase, and ≤40% by the 4,4′‐ODA/s‐BPDA polyimide phase. When the ratio between the two diamines was close to 1:1, the properties of the copolyimides were very irregular, which means a complicated internal structure. Copyright © 2011 Society of Chemical Industry     

Sequence analysis and fiber properties of a blend of poly(ethylene terephthalate) and poly(ethylene terephthalate‐co‐4,4′‐bibenzoate)

Blends of poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate‐co‐4,4′‐ bibenzoate) (PETBB) are prepared by coextrusion. Analysis by ¹³C‐NMR spectroscopy shows that little transesterification occurs during the blending process. Additional heat treatment of the blend leads to more transesterification and a corresponding increase in the degree of randomness, R. Analysis by differential scanning calorimetry shows that the as‐extruded blend is semicrystalline, unlike PETBB15, a random copolymer with the same composition as the non‐ random blend. Additional heat treatment of the blend leads to a decrease in the melting point, T_m, and an increase in glass transition temperature, T_g. The T_m and T_g of the blend reach minimum and maximum values, respectively, after 15 min at 270°C, at which point the blend has not been fully randomized. The blend has a lower crystallization rate than PET and PETBB55 (a copolymer containing 55 mol % bibenzoate). The PET/PETBB55 (70/30 w/w) blend shows a secondary endothermic peak at 15°C above an isothermal crystallization temperature. The secondary peak was confirmed to be the melting of small and/or imperfect crystals resulting from secondary crystallization. The blend exhibits the crystal structure of PET. Tensile properties of the fibers prepared from the blend are comparable to those of PET fiber, whereas PETBB55 fibers display higher performance. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1793–1803, 2004     

Effects of aromatic carboxylic dianhydrides on thermomechanical properties of polybenzoxazine‐dianhydride copolymers

Enhanced thermomechanical properties of bisphenol‐A based polybenzoxazine (PBA‐a) copolymers obtained by reacting bisphenol‐A‐aniline‐type benzoxazine (BA‐a) resin with three different aromatic carboxylic dianhydrides, i.e., pyromellitic dianhydride (PMDA), 3,3′,4,4′ biphenyltetracarboxylic dianhydride (s‐BPDA), or 3,3′,4,4′ benzophenonetetracarboxylic dianhydride (BTDA) were reported. Glass transition temperature (T_g), of the copolymers was found to be in the order of PBA‐a:PMDA>PBA‐a:s‐BPDA>PBA‐a:‐BTDA. The difference in the T_g of the copolymers is related to the rigidity of the dianhydride components. Furthermore, the T_g of PBA‐a:BTDA, PBA‐a:s‐BPDA, and PBA‐a:BTDA films was observed to be significantly higher than that of the neat PBA‐a owing to the enhanced crosslink density by the dianhydride addition. This greater crosslink density results from additional ester linkage formation between the hydroxyl group of PBA‐a and the anhydride group of dianhydrides formed by thermal curing. Moreover, the copolymers exhibit enhanced thermal stability with thermal degradation temperature (T_d) ranging from 410°C to 426°C under nitrogen atmosphere. The char yield at 800°C of the copolymers was found to be remarkably greater than that of the neat PBA‐a with a value up to 60% vs. that of about 38% of the PBA‐a. Toughness of the copolymer films was greatly improved compared to that of the neat PBA‐a. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Preparation and properties of polyimide/silica hybrid composites based on polymer‐modified colloidal silica

A new type of polyimide/silica (PI/SiO₂) hybrid composite films was prepared by blending polymer‐modified colloidal silica with the semiflexible polyimide. Polyimide was solution‐imidized at higher temperature than the glass transition temperature (T_g) using 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and 4,4′‐diaminodiphenyl ether (ODA). The morphological observation on the prepared hybrid films by scanning electron microscopy (SEM) pointed to the existence of miscible organic–inorganic phase, which resulted in improved mechanical properties compared with pure PI. The incorporation of the silica structures in the PI matrix also increased both T_g and thermal stability of the resulting films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2053–2061, 2006     

Crystallization of 2‐methyl‐1,3‐propanediol substituted poly(ethylene terephthalate). I. Thermal behavior and isothermal crystallization

Differential scanning calorimetry (DSC) was used to evaluate the thermal behavior and isothermal crystallization kinetics of poly(ethylene terephthalate) (PET) copolymers containing 2‐methyl‐1,3‐propanediol as a comonomer unit. The addition of comonomer reduces the melting temperature and decreases the range between the glass transition and melting point. The rate of crystallization is also decreased with the addition of this comonomer. In this case it appears that the more flexible glycol group does not significantly increase crystallization rates by promoting chain folding during crystallization, as has been suggested for some other glycol‐modified PET copolyesters. The melting behavior following isothermal crystallization was examined using a Hoffman–Weeks approach, showing very good linearity for all copolymers tested, and predicted an equilibrium melting temperature (T_m⁰) of 280.0°C for PET homopolymer, in agreement with literature values. The remaining copolymers showed a marked decrease in T_m⁰ with increasing copolymer composition. The results of this study support the claim that these comonomers are excluded from the polymer crystal during growth. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2592–2603, 2006     

Carbon black‐filled poly(ethylene‐co‐alkyl acrylate) composites: Calorimetric studies

The calorimetric characteristics of carbon black (CB)/poly(ethylene‐co‐alkyl acrylate) composites depend on both the CB and acrylate contents. An increase of the acrylate content in the pure copolymers tends to decrease all the crystalline characteristics: T_c,n, the nonisothermal crystallization temperature; T_m, the melting temperature, and ΔH_m, the melting enthalpy. CB modifies the crystallization kinetics of poly(ethylene‐co‐ethyl acrylate) (EEA) alone and in blends with poly(ethylene‐co‐24% w/w methyl acrylate) (24EMA) and poly(ethylene‐co‐35% w/w methyl acrylate) (35EMA). In the presence of CB, T_c,n, the nonisothermal crystallization temperature of EEA, increases and t_1/2, the half‐crystallization time, decreases for a given isothermal crystallization temperature, T_c,i. The thermograms obtained during the melting of EEA after isothermal crystallization show multiple endotherms, suggesting that crystalline‐phase segregation has occurred. The existence of different crystalline species can be explained by the presence of fractions of different acrylate content in the copolymers as shown by SEC. Therefore, CB does not seem to have much effect on the subsequent melting temperature of EEA, T_m,s. CB also induces a lower melting enthalpy, Δ H_m, in the blends. This decrease of ΔH_m appears to be constant whatever the compound, but when reported to the melting enthalpy of the polymer without CB, δΔH_m/ΔH_m increases with the acrylate content. A slight increase of the amorphous phase stiffness after CB introduction is noticed: The T_g of EEA/24EMA and EEA/35EMA blends increases by several degrees. Therefore, plotting ΔH_m versus ΔC_p shows that for the same ΔH_m the ΔC_p is lower in CB‐filled samples, suggesting there is some kind of rigid amorphous phase not contributing to the glass transition. We propose to explain the CB activity during the crystallization process by the existence of molecular interactions between CB and acrylate groups rather than by a pure nucleating effect. Thus, the increase of T_c,n and the decrease of ΔH_m could be explained by the fact that CB separates acrylate‐rich chains from the crystallization medium, accelerating the crystallization of the acrylate‐poor chains. During such a crystallization process, CB may be preferentially localized in the more polar amorphous phase and scattered between the two crystalline phases of EEA and EXA. These blends of poly(ethylene‐co‐alkyl acrylate) copolymers with CB provide interesting materials with adjustable properties depending on the acrylate and CB contents and on the thermomechanical treatments. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 779–793, 2001     

Structure and properties of aromatic poly(benzimidazole‐imide) copolymer fibers

A series of co‐polyimide fibers were prepared by thermal imidization of copolyamic acids derived from 3,3′,4,4′‐biphenyltertracarboxylic dianhydride (BPDA) and pyromellitic dianhydride (PMDA) in various molar ratios with 2‐(4‐aminophenyl)?5‐aminobenzimidazole (BIA). The dynamic mechanical behaviors of these polyimide (PI) fibers revealed that the glass transition temperature (T_g) was significantly improved upon increasing PMDA content. Heat‐drawing process led to dramatic change on the glass transition behavior of BPDA/BIA system, but had a small impact on BPDA/PMDA/BIA co‐polyimide fibers. This difference for PI fibers is attributed to the different degree of ordered structure of the fibers affected by heat‐drawing. The incorporation of PMDA obviously improved the dimensional stability against high temperature, due to the restricted movement of polymer chains. In addition, the obtained fibers show excellent mechanical and thermal properties because of the strong hydrogen bonding due to the incorporation of benzimidazole moieties. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41474.     

How the monomer concentration of polymerization influences various properties of polybenzimidazole: A case study with poly(4,4′‐diphenylether‐5,5′‐bibenzimidazole)

In this work, a series of poly(4,4′‐diphenylether‐5,5′‐bibenzimidazole)s (OPBIs) were synthesized from 4,4′‐oxybis(benzoic acid) and 3,3′,4,4′‐tetraaminobiphenyl through the variation of the initial monomer concentration with a solution polycondensation technique in a poly(phosphoric acid) medium. The resulting polymers were characterized by various techniques such as infrared (IR), nuclear magnetic resonance, dynamic mechanical analysis (DMA), and thermogravimetric analysis. The initial monomer concentration in the polymerization mixture played an important role in controlling the molecular weight of the resulting polymers. A temperature‐dependent IR study showed that the free movement of the ? NH group of the imidazole ring was blocked by the absorbed moisture. The DMA study showed that the glass‐transition temperature (T_g) varied with the molecular weight, and the presence of the ether linkage in the OPBI polymer backbone had a significant influence on T_g. A high‐molecular‐weight OPBI polymer tended to form a supramolecular organization, which influenced the thermal characteristic of the polymer. Photophysical studies demonstrated the fluorescent characteristics of the OPBI polymers in both solid and solution states. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparations and properties of a high performance semicrystalline copolyimide and composites reinforced with glass fiber

A semicrystalline copolyimide derived from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (s‐BPDA), 1,3‐bis‐(4‐aminophenoxy)benzene (TPER), and 4,4′‐oxydianiline (4,4′‐ODA), end capped with phthalic anhydride (PA), was synthesized. Glass fiber reinforced composite was also prepared by impregnating powdery glass fiber with poly(amic acid) followed by solution imidization techniques. This copolyimide displayed a glass transition temperature of 202°C and a melting temperature of 373°C by differential scanning colorimeter (DSC). Crystallization and melting behaviors were investigated under nonisothermal and isothermal crystallization conditions. Double exothermic peaks were found by DSC when the copolyimide was cooled from the melt and multiple melting behaviors can be observed after the coployimide had been isothermally crystallized at different temperatures. Mechanical properties were investigated by dynamical mechanical analysis (DMA) and tensile experiments. The samples were cured at different temperatures and then tested at different temperatures. Results indicated that the copolyimide and the composite showed excellent mechanical properties. Additionally, this copolyimide also showed lower melt viscosity by rheological analysis. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40345.     

Synthesis and characterization of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers with dibutylmagnesium as catalyst

Two series of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers were prepared by the ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) and dibutylmagnesium in 1,4‐dioxane solution at 70°C. The triblock structure and molecular weight of the copolymers were analyzed and confirmed by ¹H NMR, ¹³C NMR, FTIR, and gel permeation chromatography. The crystallization and thermal properties of the copolymers were investigated by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). The results illustrated that the crystallization and melting behaviors of the copolymers were depended on the copolymer composition and the relative length of each block in copolymers. Crystallization exothermal peaks (T_c) and melting endothermic peaks (T_m) of PEG block were significantly influenced by the relative length of PCL blocks, due to the hindrance of the lateral PCL blocks. With increasing of the length of PCL blocks, the diffraction and the melting peak of PEG block disappeared gradually in the WAXD patterns and DSC curves, respectively. In contrast, the crystallization of PCL blocks was not suppressed by the middle PEG block. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Copolycondensation of IPA/TPA,BPA, and 4,4′‐dihydroxydipehnylsulfone and 4,4′‐dicarboxydiphenylsulfone

Copolycondensations of IPA, TPA, bisphenol A (BPA), and several cimonomers were carried out to improve thermal properties, such as, the glass transition temperature (T_g) of the IPA/TPA (50/50)–BPA polyester. Among the comonomers examined, 4,4′‐Dihydroxydiphenylsulfone (BPS) and 4,4′‐Dicarboxydiphenylsulfone (DCDPS) having a strongly dipolar sulfonyl group in the chain were significantly effective. The favorable effect upon the T_gs was studied by varying the amounts of BPS and DCDPS incorporated into the copolymers. In the copolycondensation with BPS, two‐stage copolycondensation of BPA first and then BPS, the reverse order of reaction, and their spontaneous addition were examined to investigate the effect of distribution of the BPS unit segments in the copolymer upon the T_gs of the resulted copolymers. The distribution was briefly studied from distribution of the IPA/TPA‐BPA oligomers in the initial reaction using GPC. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 875–879, 2000     

Synthesis and properties of novel alicyclic‐functionalized polyimides prepared from natural—(D)‐camphor

In this article, a new alicyclic‐functionalized diamine, 1,3‐bis(4‐aminophenoxymethylene)‐1,2,2‐trimethylclopentane (BAMT) was successfully synthesized starting from natural —(D)‐camphor through four reaction steps of oxidation to offer a dicaboxylic acid, reduction to offer a diol, nucleophilic substitution to give a dinitro compound and then reduction to give the final diamine. Two alicyclic‐containing polyimides were prepared by polycondensing BAMT with 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and 4,4′‐oxydiphthalicanhydride (ODPA), respectively. For the studies of the structure–property relationships of the polyimides, one aromatic polyimide of 4, 4′‐oxydianiline (ODA) polycondensed with ODPA was prepared in comparison. The alicyclic‐containinig polyimides PI (BPDA‐BAMT) and PI (ODPA‐BAMT) maintain good thermal properties with glass transition temperatures (T_g) of 257°C and 240°C, and temperatures at 5% weight loss (T₅) of 443°C and 436°C in nitrogen, respectively. The alicyclic polyimides exhibit tensile strengths of 91.9–133 MPa, Young's moduli of 2.75—3.24 GPa, and elongations at break of 5.6–18%. Compared with the aromatic polyimide PI (ODPA‐ODA), PI (ODPA‐BAMT) shows improved transparency with the UV‐Vis transmittance at 500 nm over 80%. In addition, PI (ODPA‐BAMT) displays better solubility than PI (ODPA‐ODA), which has been confirmed by the bigger d‐spacing value of PI (ODPA‐BAMT) than that of PI (ODPA‐ODA) calculated from the Wide‐angle X‐ray Diffraction spectra. This study indicates that the renewable forestry compound, such as natural —(D)‐camphor, could be a good origin for the structural designing and preparation of alicyclic‐containing polyimides with outstanding combined features suitable for advanced microelectronic and optoelectronic applications. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Crystallization kinetics of poly(1,4‐butylene‐co‐ethylene terephthalate)

The crystallization kinetics of poly(butylene terephthalate) (PBT), poly(ethylene terephthalate) (PET), and their copolymers poly(1,4‐butylene‐co‐ethylene terephthalate) (PBET) containing 70/30, 65/35 and 60/40 molar ratios of 1,4‐butanediol/ethylene glycol were investigated using differential scanning calorimetry (DSC) at crystallization temperatures (T_c) which were 35–90 °C below equilibrium melting temperature . Although these copolymers contain both monomers in high proportion, DSC data revealed for copolymer crystallization behaviour. The reason for such copolymers being able to crystallize could be due to the similar chemical structures of 1,4‐butanediol and ethylene glycol. DSC results for isothermal crystallization revealed that random copolymers had a lower degree of crystallinity and lower crystallite growth rate than those of homopolymers. DSC heating scans, after completion of isothermal crystallization, showed triple melting endotherms for all these polyesters, similar to those of other polymers as reported in the literature. The crystallization isotherms followed the Avrami equation with an exponent n of 2–2.5 for PET and 2.5–3.0 for PBT and PBETs. Analyses of the Lauritzen–Hoffman equation for DSC isothermal crystallization data revealed that PBT and PET had higher growth rate constant G_o, and nucleation constant K_g than those of PBET copolymers. © 2001 Society of Chemical Industry     

Crystallization kinetics and melting behavior of poly[(trimethylene terephthalate)‐co‐(29 mol % ethylene terephthalate)] copolyester

The copolyester was characterized as having 71 mol % trimethylene terephthalate units and 29 mol % ethylene terephthalate units in a random sequence according to the NMR spectra. Differential scanning calorimeter (DSC) was used to investigate the isothermal crystallization kinetics in the temperature range (T_c) from 130 to 170°C. The melting behavior after isothermal crystallization was studied using DSC and temperature‐modulated DSC by varying the T_c, the crystallization time, and the heating rate. The DSC thermograms and wide‐angle X‐ray diffraction patterns reveal that the complex melting behavior involves melting‐recrystallization‐remelting and different lamellar crystals. As the T_c increases, the contribution of recrystallization gradually falls and finally disappears. A Hoffman‐Weeks linear plot yields an equilibrium melting temperature of 198.7°C. The kinetic analysis of the growth rates of spherulites and the change in the morphology from regular to banded spherulites indicate that a regime II→III transition occurs at 148°C. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Modification of bismaleimide resin by poly(ethylene phthalate‐co‐ethylene terephthalate), poly(ethylene phthalate‐co‐ethylene 4,4′‐biphenyl dicarboxylate), and poly(ethylene phthalate‐co‐ethylene 2,6‐naphthalene dicarboxylate)

Aromatic polyesters were prepared and used to improve the brittleness of bismaleimide resin, composed of 4,4′‐bismaleimidodiphenyl methane and o,o′‐diallyl bisphenol A (Matrimid 5292 A/B resin). The aromatic polyesters included PEPT [poly(ethylene phthalate‐co‐ethylene terephthalate)], with 50 mol % of terephthalate, PEPB [poly(ethylene phthalate‐co‐ethylene 4,4′‐biphenyl dicarboxylate)], with 50 mol % of 4,4′‐biphenyl dicarboxylate, and PEPN [poly(ethylene phthalate‐co‐ethylene 2,6‐naphthalene dicarboxylate)], with 50 mol % 2,6‐naphthalene dicarboxylate unit. The polyesters were effective modifiers for improving the brittleness of the bismaleimide resin. For example, inclusion of 15 wt % PEPT (MW = 9300) led to a 75% increase in fracture toughness, with retention in flexural properties and a slight loss of the glass‐transition temperature, compared with the mechanical and thermal properties of the unmodified cured bismaleimide resin. Microstructures of the modified resins were examined by scanning electron microscopy and dynamic viscoelastic analysis. The toughening mechanism was assessed as it related to the morphological and dynamic viscoelastic behaviors of the modified bismaleimide resin system. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2352–2367, 2001     

Molecular simulation of the glass transition and proton conductivity of 2,2′‐benzidinedisulfonic acid and 4,4′‐diaminodiphenylether‐2,2′‐disulfonic acid‐based copolyimides as polyelectrolytes for fuel cell applications

The glass transition temperatures (T_gs) and proton conductivities of polyimides synthesized from naphthalene‐1,4,5,8‐tetracarboxylic dianhydride (NTDA), 2,2′‐benzidinedisulfonic acid (BDSA), 4,4′‐diaminodiphenylether‐2,2′‐disulfonic acid (ODADS), and non‐sulfonated diamine monomers have been predicted using molecular dynamics simulations. The specific volumes for two dry and four hydrated NTDA‐based polyimides were plotted versus temperatures above and below T_gs to obtain the glass transition temperatures. The simulation results suggest that the ODADS‐based polyimide membranes exhibit lower T_gs and thus better mechanical properties than the BDSA‐based polyimides, which may be attributed to the high mobility of backbones of ODADS as supported by the vectorial autocorrelation function (VACF) results of this study. In addition, comparison of the simulated T_gs for the dry and hydrated ODADS‐based polyimides has shown that water content in polyimides can affect their T_gs. The proton conductivities of a representative polyimide in both dry and hydrated conditions have been obtained from molecular dynamics simulations of the proton and hydronium ion diffusion. The simulated conductivity for the hydrated NTDA‐ODADS/BAPB cell is in reasonable agreement with the experimental value obtained from the AC impedance method. The relationship between the chemical composition, chain flexibility, and the glass transition and proton conduction of these NTDA‐based polyimides was explored on the basis of VACF and pair correlation function analysis. Copyright © 2006 Society of Chemical Industry     

Syntheses and properties of polyimides derived from diamines containing 2,5‐disubstituted pyridine group

A series of novel homo‐ and copolyimides containing pyridine units were prepared from the heteroaromatic diamines, 2,5‐bis (4‐aminophenyl) pyridine and 2‐(4‐aminophenyl)‐5‐aminopyridine, with pyromelltic dianhydride (PMDA), and 3,3′, 4,4′‐biphenyl tertracarboxylic dianhydride (BPDA) via a conventional two‐step thermal imidizaton method. The poly(amic acid) precursors have inherent viscosities of 1.60–9.64 dL/g (c = 0.5 g/dL in DMAC, 30°C) and all of them can be cast and thermally converted into flexible and tough polyimide films. All of the polyimides show excellent thermal stability and mechanical properties. The polyimides have 10% weight loss temperature in the range of 548–598°C in air. The glass transition temperatures of the PMDA‐based samples are in the range of 395–438°C, while the BPDA‐based polyimides show two glass transition temperatures (T_g1 and T_g2), ranging from 268 to 353°C and from 395 to 418°C, respectively. The flexible films possess tensile modulus in the range of 3.42–6.39 GPa, strength in the range of 112–363 MPa and an elongation at break in the range of 1.2–69%. The strong reflection peaks in the wide‐angle X‐ray diffraction patterns indicate that the polyimides have a high packing density and crystallinity. The polymer films are insoluble in common organic solvents exhibiting high chemical resistance. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1844–1851, 2006     

Synthesis and characterization of organosoluble and transparent polyimides derived from trans‐1,2‐bis(3,4‐dicarboxyphenoxy)cyclohexane dianhydride

A novel dianhydride, trans‐1,2‐bis(3,4‐dicarboxyphenoxy)cyclohexane dianhydride (1,2‐CHDPA), was prepared through aromatic nucleophilic substitution reaction of 4‐nitrophthalonitrile with trans‐cyclohexane‐1,2‐diol followed by hydrolysis and dehydration. A series of polyimides (PIs) were synthesized from one‐step polycondensation of 1,2‐CHDPA with several aromatic diamines, such as 2,2′‐bis(trifluoromethyl)biphenyl‐4,4′‐diamine (TFDB), bis(4‐amino‐2‐trifluoromethylphenyl)ether (TFODA), 4,4′‐diaminodiphenyl ether (ODA), 1,4‐bis(4‐aminophenoxy)benzene (TPEQ), 4,4′‐(1,3‐phenylenedioxy)dianiline (TPER), 2,2′‐bis[4‐(3‐aminodiphenoxy)phenyl]sulfone (m‐BAPS), and 2,2′‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]sulfone (6F‐BAPS). The glass transition temperatures (T_gs) of the polymers were higher than 198°C, and the 5% weight loss temperatures (T_d5%s) were in the range of 424–445°C in nitrogen and 415–430°C in air, respectively. All the PIs were endowed with high solubility in common organic solvents and could be cast into tough and flexible films, which exhibited good mechanical properties with tensile strengths of 76–105 MPa, elongations at break of 4.7–7.6%, and tensile moduli of 1.9–2.6 GPa. In particular, the PI films showed excellent optical transparency in the visible region with the cut‐off wavelengths of 369–375 nm owing to the introduction of trans‐1,2‐cyclohexane moiety into the main chain. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42317.     

Blends of bacterial poly[(R)‐3‐hydroxybutyrate] with oligo[(R,S)‐3‐hydroxybutyrate]‐diol

The miscibility, melting and crystallization behaviour of poly[(R)‐3‐hydroxybutyrate], PHB, and oligo[(R,S)‐3‐hydroxybutyrate]‐diol, oligo‐HB, blends have been investigated by differential scanning calorimetry: thermograms of blends containing up to 60 wt% oligo‐HB showed behaviour characteristic of single‐phase amorphous glasses with a composition dependent glass transition, T_g, and a depression in the equilibrium melting temperature of PHB. The negative value of the interaction parameter, determined from the equilibrium melting depression, confirms miscibility between blend components. In parallel studies, glass transition relaxations of different melt‐crystallized polymer blends containing 0–20 wt% oligo‐HB were dielectrically investigated between ?70 °C and 120 °C in the 100 Hz to 50 kHz range. The results revealed the existence of a single α‐relaxation process for blends, indicating the miscibility between amorphous fractions of PHB and oligo‐HB. © 2002 Society of Chemical Industry     

Synthesis and characterization of homo‐ and copolymers of 3‐(2‐cyano ethoxy)methyl‐ and 3‐[methoxy(triethylenoxy)]methyl‐3′‐methyl‐oxetane

Two oxetane‐derived monomers 3‐(2‐cyanoethoxy)methyl‐ and 3‐(methoxy(triethylenoxy)) methyl‐3′‐methyloxetane were prepared from the reaction of 3‐methyl‐3′‐hydroxymethyloxetane with acrylonitrile and triethylene glycol monomethyl ether, respectively. Their homo‐ and copolyethers were synthesized with BF₃· Et₂O/1,4‐butanediol and trifluoromethane sulfonic acid as initiator through cationic ring‐opening polymerization. The structure of the polymers was characterized by FTIR and¹H NMR. The ratio of two repeating units incorporated into the copolymers is well consistent with the feed ratio. Regarding glass transition temperature (T_g), the DSC data imply that the resulting copolymers have a lower T_g than pure poly(ethylene oxide). Moreover, the TGA measurements reveal that they possess in general a high heat decomposition temperature. The ion conductivity of a sample (P‐AN 20) is 1.07 × 10^?5 S cm^?1 at room temperature and 2.79 × 10^?4 S cm^?1 at 80 °C, thus presenting the potential to meet the practical requirement of lithium ion batteries for polymer electrolytes. Copyright © 2005 Society of Chemical Industry