Rapid crystallization of poly(l-lactic acid) induced by a nanoscaled zinc citrate complex as nucleating agent

A nanoscaled zinc citrate complex (ZnCC) was synthesized by the reaction of zinc acetate and citric acid using solution method. As a new eco-friendly nucleating agent, ZnCC was introduced into poly(l-lactic acid) (PLLA) via melt blending. The nonisothermal and isothermal crystallization, melting behavior, crystalline morphology and mechanical properties of the PLLA/ZnCC blends were investigated. It is found that ZnCC exhibits much more prominent nucleation activity on the crystallization of PLLA than conventional nucleating agent talc and commercial zinc citrate (ZnCit). By loading 0.05 wt% ZnCC, PLLA can complete crystallization upon cooling at 10 °C/min, and the crystallization peak shifts to a higher temperature with increasing ZnCC content. In the case of isothermal crystallization from the melt, the addition of ZnCC leads to a shorter crystallization time and a faster overall crystallization rate. Besides, the nucleation density of PLLA increases and the spherulite size decreases significantly in the presence of ZnCC. Epitaxy is the possible mechanism to elucidate the nucleation phenomenon of PLLA/ZnCC system. The tensile results show that ZnCC has a plasticization effect on the amorphous PLLA. Through a short-time annealing procedure, the mechanical properties such as tensile modulus and storage modulus of PLLA are improved by the addition of ZnCC.     

Effect of nucleating agents on the crystallization behavior and heat resistance of poly(l‐lactide)

Poly (l ‐lactide) (PLLA) blends with various nucleators were prepared by melt processing. The effect of different nucleators on the crystallization behavior and heat resistance as well as thermomechanical properties of PLLA was studied systematically by differential scanning calorimetry, X‐ray diffraction, heat deflection temperature tester, and dynamic mechanical analysis. It was found that poly(d ‐lactide), talcum powder (Talc), a multiamide compound (TMC‐328, abbreviated as TMC) can significantly improve the crystallization rate and crystallinity of PLLA, thus improving thermal–resistant property. The heat deflection temperature of nucleated PLLA can be as high as 150°C. The storage modulus of nucleated PLLA is higher than that of PLLA at the temperature above T_g of PLLA. Compared with other nucleating agents, TMC was much more efficient at enhancing the crystallization of PLLA and the PLLA containing TMC showed the best heat resistance. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42999.     

Crystallization behavior of biodegradable poly(L‐lactide)/multiwalled carbon nanotubes nanocomposites from the amorphous state

Crystallization behavior of biodegradable poly(L ‐lactide) (PLLA) and its nanocomposites at different carboxyl‐functionalized multiwalled carbon nanotubes (f‐MWNTs) contents from the amorphous state was studied in detail in this work. For the isothermal cold crystallization, the presence of f‐MWNTs enhances the isothermal cold crystallization of PLLA in the nanocomposites compared with that of neat PLLA at the same crystallization temperature; moreover, the overall cold crystallization rate of PLLA increases with increasing the f‐MWNTs content in the PLLA matrix while the crystallization mechanism does not change. For the nonisothermal crystallization, the f‐MWNTs also accelerate the crystallization process of PLLA. In addition, the activation energies of nonisothermal cold crystallization process were calculated using both the Kissinger and Friedman methods. The cold crystallization activation energies of PLLA are higher in the nanocomposites than in neat PLLA, indicating that the addition of f‐MWNTs into the PLLA matrix acts as a physical hindrance to retard crystallization. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Effect of 1,3,5‐trialkyl‐benzenetricarboxylamide on the crystallization of poly(lactic acid)

A series of 1,3,5‐trialkyl‐benzenetricarboxylamides (BTA‐Rs) with different side‐chain lengths of n‐alkyl are synthesized to use as nucleating agents of poly (lactic acid) (PLA). Crystallization rate of PLA is detailed discussed in nonisothermal melt‐crystallization with addition of the synthesized nucleating agents. Among these BTA‐Rs, BTA‐n‐butyl (BTA‐nBu) shows the most excellent nucleation ability for PLA. The influences of BTA‐nBu on the nonisothermal melt‐crystallization and cold‐crystallization from the glassy state, isothermal crystallization, crystalline structure, and spherulite morphology of PLA are investigated. It is found that 0.8 wt % is the optimal weight fraction of BTA‐nBu to improve the crystallization of PLA. In the case of isothermal melt‐crystallization from melt, the addition of BTA‐nBu shortens the crystallization half‐time and speeds up the crystallization rate of PLA with no discernible effect on the crystalline structure. Besides, BTA‐nBu nucleated PLA exhibits smaller spherulites size and larger nucleation density than that of pure PLA. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1328‐1336, 2013     

Enhanced nonisothermal and isothermal cold crystallization kinetics of biodegradable poly(l‐lactide) by trisilanolisobutyl‐polyhedral oligomeric silsesquioxanes in their nanocomposites

In this work, the nonisothermal and isothermal cold crystallization behaviors of poly(l ‐lactide) (PLLA)/trisilanolisobutyl‐polyhedral oligomeric silsesquioxanes (tsib‐POSS) nanocomposites with low tsib‐POSS contents were fully investigated. For all the samples, the variations of heating rate and the tsib‐POSS loading may influence the nonisothermal cold crystallization of PLLA. During the nonisothermal crystallization kinetics study, the Ozawa equation failed to fit the nonisothermal crystallization process of PLLA, while the Tobin equation could fit it well. For the isothermal crystallization kinetics study, the crystallization rates of all the samples increased with increasing crystallization temperature. The cold crystallization activation energy of PLLA was increased with 1 wt % tsib‐POSS. Moreover, the addition of tsib‐POSS and the increment of tsib‐POSS loading could increase the crystallization rate of PLLA, indicating the nucleating agent effect of tsib‐POSS. However, the crystallization mechanism and crystal structure of PLLA remained unchanged in the nanocomposites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43896.     

Crystallization behavior of biodegradable poly(L‐lactic acid) filled with a powerful nucleating agent: N,N′‐bis(benzoyl) suberic acid dihydrazide

N,N′‐Bis(benzoyl) suberic acid dihydrazide (NA) as nucleating agent for poly(L ‐lactic acid) (PLLA) was synthesized from benzoyl hydrazine and suberoyl chloride, which was deprived from suberic acid via acylation. PLLA/NA samples were prepared by melt blending and a hot‐press forming process. The nonisothermal and isothermal crystallization, spherulite morphology, and melting behavior of PLLA/NA with different contents of NA were investigated with differential scanning calorimetry, depolarized‐light intensity measurement, scanning electron microscopy, polarized optical microscopy, and wide‐angle X‐ray diffraction. With the incorporation of NA, the crystallization peak became sharper and shifted to a higher temperature as the degree of supercooling decreased at a cooling rate of 1°C/min from the melt. Nonisothermal crystallization indicated that the presence of NA accelerated the overall PLLA crystallization. In isothermal crystallization from the melt, the presence of NA affected the isothermal crystalline behaviors of PLLA remarkably. The addition of NA led to a shorter crystallization time and a faster overall crystallization rate; this meant that there was a heterogeneous nucleation effect of NA on the crystallization of PLLA. With the addition of 0.8% NA, the crystallization half‐time of PLLA/NA decreased from 26.5 to 1.4 min at 115°C. The Avrami theory was used to describe the kinetics of isothermal crystallization of the PLLA/NA samples. Also, with the presence of NA, the spherulite number of PLLA increased, and the spherulite size decreased significantly. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Crystallization kinetics of poly(L‐lactide)/carbonated hydroxyapatite nanocomposite microspheres

Microspheres consisting of carbonated hydroxyapatite (CHAp) nanoparticles and poly(L ‐lactide) (PLLA) have been fabricated for use in the construction of osetoconductive bone tissue engineering scaffolds by selective laser sintering (SLS). In SLS, PLLA polymer melts and crystallizes. It is therefore necessary to study the crystallization kinetics of PLLA/CHAp nanocomposites. The effects of 10 wt% CHAp nanoparticles on the isothermal and nonisothermal crystallization behavior of PLLA matrix were studied, using neat PLLA for comparisons. The Avrami equation was successfully applied for the analysis of isothermal crystallization kinetics. Using the Lauritzen‐Hoffman theory, the transition temperature from crystallization Regime II to Regime III was found to be around 120°C for both neat PLLA and PLLA/CHAp nanocomposite. The combined Avrami‐Ozawa equation was used to analyze the nonisothermal crystallization process, and it was found that the Ozawa exponent was equal to the Avrami exponent for neat PLLA and PLLA/CHAp nanocomposite, respectively. The effective activation energy as a function of the relative crystallinity and temperature for neat PLLA and PLLA/CHAp nanocomposite under the nonisothermal crystallization condition was obtained by using the Friedman differential isoconversion method. The Lauritzen‐Hoffman parameters were also determined from the nonisothermal crystallization data by using the Vyazovkin‐Sbirrazzuoli equation. CHAp nanoparticles in the composite acted as an efficient nucleating agent, enhancing the nucleation rate but at the same time reducing the spherulite growth rate. This investigation has provided significant insights into the crystallization behavior of PLLA/CHAp nanocomposites, and the results obtained are very useful for making good quality PLLA/CHAp scaffolds through SLS. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Poly(l‐lactic acid) with the organic nucleating agent N,N,N′‐tris(1H‐benzotriazole) trimesinic acid acethydrazide: Crystallization and melting behavior

N,N,N′‐Tris(1H‐benzotriazole) trimesinic acid acethydrazide (BD) was synthesized from 1H‐benzotriazole acetohydrazide and trischloride to serve as an organic nucleating agent for the crystallization of poly(l ‐lactic acid) (PLLA). First, the thermogravimetric analysis of BD exhibited a high thermal decomposition temperature; this indicated that BD maybe used as a heterogeneous nucleating agent of PLLA. Then, the effect of BD on the crystallization and melting behavior of PLLA was investigated through differential scanning calorimetry, depolarized light intensity measurements, and wide‐angle X‐ray diffraction. The appearance of a nonisothermal crystallization peak and increases in the glass‐transition temperature and the intensity of the diffraction peak suggested that the presence of BD accelerated the overall PLLA crystallization. Upon cooling at a rate of 1°C/min, the addition of just 0.5 wt % BD to PLLA increased the onset crystallization temperature from 101.4 to 111.3°C, and the nonisothermal crystallization enthalpy increased from 0.1 to 38.6 J/g. The isothermal crystallization behavior showed that the crystallization half‐time of PLLA with 0.5 wt % BD (PLLA/0.5% BD) decreased from 49.9 to 1.1 min at 105°C. However, the equilibrium melting point of PLLA/0.5% BD was lower than that of the pristine PLLA; this resulted from the increasing nucleating density of PLLA. The melting behavior of PLLA/0.5% BD further confirmed that BD improved the crystallization of PLLA, and the double‐melting peaks of PLLA/0.5% BD were assigned to melting–recrystallization. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42402.     

Synergistic effect of poly(ethylene glycol) and graphene oxides on the crystallization behavior of poly(l‐lactide)

In this article, we report the combined effects of poly(ethylene glycol) (PEG) and/or graphene oxides (GOs) on the crystallization behavior of poly(l ‐lactide) (PLLA) under different crystallization conditions, such as nonisothermal crystallization, isothermal crystallization, and annealing‐induced cold crystallization. Differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction, and polarized optical microscopy were used to study the crystallization kinetics and crystallinity to illustrate the effects of PEG and/or GOs on the crystallization behavior of PLLA. The results show that PEG functioned as a plasticizer and improved the chain mobility of /PLLA during crystallization and the GOs acted as efficient nucleation agents and accelerated the crystallization rate. Finally, both PEG and GOs improved the crystallization ability of PLLA. Importantly, the simultaneous addition of PEG and GOs led to a synergistic effect on the crystallization behavior of PLLA under all conditions. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3498–3508, 2013     

Crystallization behavior and mechanical properties of bio‐based green composites based on poly(L‐lactide) and kenaf fiber

Bio‐based polymer composite was successfully fabricated from plant‐derived kenaf fiber (KF) and renewable resource‐based biodegradable polyester, poly(L ‐lactide) (PLLA), by melt‐mixing technique. The effect of the KF weight contents (0, 10, 20, and 30 wt %) on crystallization behavior, composite morphology, mechanical, and dynamic mechanical properties of PLLA/KF composites were investigated. It was found that the incorporation of KF significantly improves the crystallization rate and tensile and storage modulus. The crystallization of PLLA can be completed during the cooling process from the melt at 5°C/min with the addition of 10 wt % KF. It was also observed that the nucleation density increases dramatically and the spherulite size drops greatly in the isothermal crystallization with the presence of KF. In addition, with the incorporation of 30 wt % KF, the half times of isothermal crystallization at 120°C and 140°C were reduced to 46.5% and 28.1% of the pure PLLA, respectively. Moreover, the tensile and storage modulus of the composite are improved by 30% and 28%, respectively, by the reinforcement with 30% KF. Scanning electron microscopy observation also showed that the crystallization rate and mechanical properties could be further improved by optimizing the interfacial interaction and compatibility between the KF and PLLA matrix. Overall, it was concluded that the KF could be the potential and promising filler for PLLA to produce biodegradable composite materials, owing to its good ability to improve the mechanical properties as well as to accelerate the crystallization of PLLA. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

聚乳酸/可反应性纳米SiO2复合材料的等温结晶动力学

采用熔融共混法制备了聚乳酸/可反应性纳米二氧化硅(PLLA/RNS)复合材料。利用差示扫描量热仪研究了RNS对PLLA等温结晶行为的影响;用Avrami 方程研究了PLLA及其复合材料的等温结晶动力学。结果表明,加入RNS对PLLA结晶起到了异相成核作用,随着RNS含量的增加,PLLA的结晶速率(K)提高,半结晶时间(t1/2)减小,而Avrami指数(n)变化不大,说明RNS没有改变PLLA结晶的成核机理;利用Arrhenius方程和Lauritzen-Hoffman理论分别对PLLA及其复合材料的结晶活化能(ΔE)、成核参数(Kg)和折叠链端表面自由能(σe)进行计算后发现,复合材料的ΔE比纯聚乳酸的小,Kg 、σe略有增加。这表明加入RNS降低了复合材料的ΔE,从而有效地促进了PLLA基体的结晶。     

A comparative study of polypropylene nucleated by individual and compounding nucleating agents. I. Melting and isothermal crystallization

In this study, melting and isothermal crystallization behaviors of polypropylene (PP) nucleated with different nucleating agents (NAs) have been comparatively studied. α‐phase NA 1,3 : 2,4‐bis (3,4‐dimethylbenzylidene) sorbitol (DMDBS, Millad 3988), β‐phase NA aryl amides compound (TMB‐5), and their compounds were introduced into PP matrix, respectively. The crystallization and melting characteristics as well as the crystallization structures and morphologies of nucleated PP were studied by differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), and polarized light microscopy (PLM). As indicated by previous work that a few amounts of α‐phase NA (DMDBS) or β‐phase NA (TMB‐5) has apparent nucleation effect for PP crystallization. However, the crystallization of PP nucleated with compounding NAs is dependent on the content of each NA. In the sample of PP with 0.1 wt % DMDBS and 0.1 wt % TMB‐5, the nucleation efficiency of TMB‐5 is much higher than that of DMDBS and PP crystallization is mainly nucleated by TMB‐5, and in this condition, β‐phase PP is the main crystallization structure. For the sample of PP with 0.2 wt % DMDBS and 0.2 wt % TMB‐5, 0.2 wt % DMDBS has higher nucleation efficiency than 0.2 wt % TMB5, and α‐phase is the main crystalline structure in this sample. The isothermal crystallization kinetics and crystallization structure have been analyzed in detail in this work. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Crystallization behavior of poly(L‐lactic acid)‐based ecocomposites prepared with kenaf fiber and rice straw

Several composites of poly(L ‐lactic acid) (PLLA) with natural fibers (kenaf and rice straw) and pigments have been prepared and analyzed. The study of the thermal behavior has shown a rather important nucleation ability of these fillers for the crystallization of the PLLA component in the composites. Thus, the cooling from the melt of pure PLLA at 10°C/min leads to an almost completely amorphous sample, while a high crystallinity (around 60%) is exhibited by the sample PLLA and rice straw (PLLA‐RS)‐yellow under those conditions. The analysis of the isothermal crystallization from the melt indicates that a maximum rate of crystallization is obtained for all the samples at around 105°C, although the rate is three times faster for samples PLLA and kenaf fiber (PLLA‐KF), PLLA‐KF‐red, and PLLA‐RS, in comparison with pure PLLA. The rate is increased by another factor of three for sample PLLA‐RS‐yellow. The analysis of the melting temperatures and crystallinities as a function of the crystallization temperature shows that there is a break at around 115°C, which seems to be related to the formation of ordered crystals at higher temperatures and disordered ones at lower temperatures. Besides, the natural fibers are environmentally friendly and nonexpensive materials, and the higher crystallization rates of the composites will result in shorter production cycles of end‐use articles. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Effect of zinc phenylphosphonate on the crystallization behavior of poly(l‐lactide)

The effect of zinc phenylphosphonate (PPZn) on the crystallization behavior of poly(l ‐lactide) (PLLA) was investigated using differential scanning calorimetry (DSC) and Polarized Optical Microscopy (POM) measurements. The non‐isothermal cold crystallization results showed that the addition of PPZn obviously decreased the cold crystallization temperature of PLLA and increased the degree of crystallinity of PLLA. The isothermal crystallization kinetics results showed that the crystallization rate of PLLA with small amount of PPZn was much higher than that of neat PLLA, and the half‐time (t_1/2) of PLLA/PPZn sample is far less than that of neat PLLA. As an effective nucleating agent, PPZn particles had also some influence on nucleation mechanism and crystal growth of PLLA. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2744–2752, 2013     

The effect of poly(ethylene glycol) mixed with poly(l‐lactic acid) on the crystallization characteristics and properties of their blends

The non‐isothermal and isothermal crystallizations of extruded poly(l ‐lactic acid) (PLLA) blends with 10, 20 and 30 wt% poly(ethylene glycol) (PEG) were investigated with differential scanning calorimetry. The formation of α‐form crystals in the blend films was verified using X‐ray diffraction and an increase in crystallinity indexes using Fourier transformation infrared spectroscopy. Crystallization and melting temperatures and crystallinity of PLLA increased with decreasing cooling rate (CR) and showed higher values for the blends. Although PLLA crystallized during both cooling and heating, after incorporation of PEG and with CR = 2 °C min^?1 its crystallization was completed during cooling. Increasingly distinct with CR, a small peak appeared on the lower temperature flank of the PLLA melting curve in the blends. A three‐dimensional nucleation process with increasing contribution from nuclei growth at higher CR was verified from Avrami analysis, whereas Kissinger's method showed that the diluent effect of 10 and 20 wt% PEG in PLLA decreased the effective energy barrier. During isothermal crystallization, crystallization half‐time increased with temperature (T_ic) for the blends, decreased with PEG content and was lower than that of pure PLLA. In addition, the Avrami rate constants were significantly higher than those of pure PLLA, at the lower T_ic. Different crystal morphologies in the PLLA phase were formed, melting in a broader and slightly higher T_m range than pure PLLA. The crystallization activation energy of PLLA decreased by 56% after the addition of 10 wt% PEG, increasing though with PEG content. Finally, PEG/PLLA blends presented improved flexibility and hydrophilicity. © 2019 Society of Chemical Industry     

Cold‐crystallization behavior of poly(L‐lactide)/ACR blend films investigated by in situ FTIR spectroscopy

The cold crystallization behavior of poly (L ‐lactide) (PLLA) blend films modified by small amount of acrylic rubber particles (ACR) have been investigated by in situ Fourier‐transform infrared (FTIR) spectroscopy. During the isothermal cold crystallization, the crystallization rate of PLLA is greatly improved with addition of only 1 wt % ACR. However, for PLLA with 8 wt % ACR, the crystallization rate is slower than that of neat PLLA. The relative crystallinity of PLLA with the addition of 1–5 wt % ACR is obviously higher than that of the neat PLLA. For the PLLA blend film with 3 % ACR, the relative crystallinity reaches a maximum. It was found that the addition of ACR particles below 5% accelerated the cold crystallization nucleation process and made the cold‐crystallization rate of PLLA/ACR be quicker than that of neat PLLA. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Isothermal and nonisothermal crystallization kinetics of poly(ε‐caprolactone)/multi‐walled carbon nanotube composites

Differential scanning calorimeter (DSC) and polarized optical microscopy (POM) have been used to investigate the isothermal and nonisothermal crystallization behavior of poly(ε‐caprolactone) (PCL)/multi‐walled carbon nanotube (MWNT) composites. PCL/MWNT composites have been prepared by mixing the PCL polymer with carboxylic groups containing multi‐walled carbon nanotubes (c‐MWNTs) in tetrahydrofuran solution. Raman spectrum of c‐MWNT indicated the possible presence of carboxylic acid groups at both ends and on the sidewalls of the MWNTs. The TEM micrograph showed that the c‐MWNT is well separated and uniformly dispersed in the PCL matrix. DSC isothermal results showed that the introduction of c‐MWNT into the PCL initiates strongly heterogeneous nucleation, which induced a change of the crystal growth process. The activation energy of PCL significantly decreases by adding 0.25 wt% c‐MWNT into PCL/c‐MWNT composites and then increases as c‐MWNT content increases. The result demonstrates that the addition of c‐MWNT into PCL induces the heterogeneous nucleation at lower c‐MWNT content and then inhibits the polymer chain transportation ability during crystallization at higher c‐MWNT content. In this study, we have also studied the nonisothermal crystallization kinetics and melting behavior of PCL/c‐MWNT composites at various cooling rates. The correlation among isothermal and nonisothermal crystallization kinetics and melting behavior of PCL/c‐MWNT composites can be also discussed. POLYM. ENG. SCI., 46:1309–1317, 2006. © 2006 Society of Plastics Engineers     

Crystallization of poly(3‐hydroxybutyrate) with stereocomplexed polylactide as biodegradable nucleation agent

Crystallization kinetics behavior and morphology of poly(3‐hydroxybutyrate) (PHB) blended with of 2–10 wt% loadings of poly(L ‐ and D ‐lactic acid) (PLLA and PDLA) stereocomplex crystallites, as biodegradable nucleating agents, were studied using differential scanning calorimetry, polarizing‐light optical microscopy (POM), and wide‐angle X‐ray diffraction (WAXD). Blending PLLA with PDLA at 1:1 weight ratio led to formation of stereocomplexed PLA (sc‐PLA), which was incorporated as small crystalline nuclei into PHB for investigating melt‐crystallization kinetics. The Avrami equation was used to analyze the isothermal crystallization of PHB. The stereocomplexed crystallites acted as nucleation sites in blends and accelerated the crystallization rates of PHB by increasing the crystallization rate constant k and decreasing the half‐time (t_1/2). The PHB crystallization was nucleated most effectively with 10 wt% stereocomplexed crystallites, as evidenced byPOM results. The sc‐PLA complexes (nucleated PHB crystals) exhibit much small spherulite sizes but possess the same crystal cell morphology as that of neat PHB based on the WAXD result. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Effects of fumed silica on the crystallization behavior and thermal properties of poly(hydroxybutyrate‐co‐hydroxyvalerate)

The effects of fumed silica on the crystallization behavior and thermal properties of poly(hydroxybutyrate‐co‐hydroxyvalerate) (PHBV) were investigated. The PHBV/silica composites were prepared by a melt‐blending method. The nonisothermal crystallization, melting process, and isothermal crystallization kinetics of PHBV and PHBV/silica composites were characterized with differential scanning calorimetry. The spherulite development and morphology were observed by polarized optical microscopy. In addition, the thermal degradation properties were determined via thermogravimetric analysis. The results indicated that the melting and crystallization kinetics of PHBV were greatly affected by fumed silica, and this was due to the effective nucleation function of silica, which enhanced the crystallization process. The thermal onset degradation temperature of PHBV increased with the addition of fumed silica. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of nucleating agent addition on crystallization of isotactic polypropylene

The isothermal and nonisothermal crystallization kinetics of nonnucleated and nucleated isotactic polypropylene (iPP) were investigated by DSC and a polarized light microscope with a hot stage. Dibenzylidene sorbitol (DBS) was used as a nucleating agent. It was found that the crystallization rate increased with the addition of DBS. The influence of DBS on fold surface energy, σ_e, was examined by the Hoffman and Lauritzen nucleation theory. It showed that σ_e decreased with the addition of DBS, suggesting that DBS is an effective nucleating agent for iPP. Ozawa's theory was used to study the nonisothermal crystallization. It was found that the crystallization temperature for the nucleated iPP was higher than that for nonnucleated iPP. The addition of DBS reduced the Ozawa exponent, suggesting a change in spherulite morphology. The cooling crystallization function has a negative exponent on the crystallization temperature. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2089–2095, 1998