pH‐sensitive swelling and release behaviors of anionic hydrogels for intelligent drug delivery system

The pH‐sensitive swelling and release behaviors of the anionic P(MAA‐co‐EGMA) hydrogels were investigated as a biological on–off switch for the design of an intelligent drug delivery system triggered by external pH changes. There was a drastic change of the equilibrium weight swelling ratio of P(MAA‐co‐EGMA) hydrogels at a pH of around 5, which is the pK_a of poly (methacrylic acid) (PMAA). At a pH below 5, the hydrogels were in a relatively collapsed state but at a pH higher than 5, the hydrogels swelled to a high degree. When the molecular weight of the pendent poly(ethylene glycol) (PEG) of the P(MAA‐co‐EGMA) increased, the swelling ratio decreased at a pH higher than 5. The pK_a values of the P(MAA‐co‐EGMA) hydrogels moved to a higher pH range as the pendent PEG molecular weight increased. When the feed concentration of the crosslinker of the hydrogel increased the swelling ratio of the P(MAA‐co‐EGMA) hydrogels decreased at a pH higher than 5. In release experiments using Rhodamine B (Rh‐B) as a model solute, the P(MAA‐co‐EGMA) hydrogels showed a pH‐sensitive release behavior. At low pH (pH 4.0) a small amount of Rh‐B was released while at high pH (pH 6.0) a relatively large amount of Rh‐B was released from the hydrogels. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Dynamic swelling behavior of pH‐sensitive anionic hydrogels used for protein delivery

There have been many attempts to use anionic hydrogels as oral protein delivery carriers because of their pH‐responsive swelling behavior. The dynamic swelling behavior of poly(methacrylic acid‐co‐methacryloxyethyl glucoside) and poly(methacrylic acid‐g‐ethylene glycol) hydrogels was investigated to determine the mechanism of water transport through these anionic hydrogels. The exponential relation M_t/M_∞ = ktⁿ (where M_t is the mass of water absorbed at time t and M_∞ is the mass of water absorbed at equilibrium) was used to calculate the exponent (n) describing the Fickian or non‐Fickian behavior of swelling polymer networks. The mechanism of water transport through these gels was significantly affected by the pH of the swelling medium. The mechanism of water transport became more relaxation‐controlled in a swelling medium of pH 7.0, which was higher than pK_a of the gels. The experimental results of the time‐dependent swelling behaviors of the gels were analyzed with several mathematical models. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1606–1613, 2003     

Preparation of pH‐sensitive poly(vinyl alcohol‐g‐methacrylic acid) and poly(vinyl alcohol‐g‐acrylic acid) hydrogels by gamma ray irradiation and their insulin release behavior

A series of pH‐responsive hydrogels were studied as potential drug carriers for the protection of insulin from the acidic environment of the stomach before releasing in the small intestine. Hydrogels based on poly(vinyl alcohol) networks grafted with acrylic acid or methacrylic acid were prepared by a two‐step process. Poly(vinyl alcohol) hydrogels were prepared by gamma ray irradiation (50 kGy) and then followed by grafting either acrylic acid or methacrylic acid onto these poly(vinyl alcohol) hydrogels with subsequent irradiation (5–20 kGy). These graft hydrogels showed pH‐sensitive swelling behavior and were used as carriers for the controlled release of insulin. The in vitro release of insulin was observed for the insulin‐loaded hydrogels in a simulated intestinal fluid (pH 6.8) but not in a simulated gastric fluid (pH 1.2). The release behavior of insulin in vivo in a rat model confirmed the effectiveness of the oral delivery of insulin to control the level of glucose. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 636–643, 2004     

Modified carrageenan. 4. Synthesis and swelling behavior of crosslinked κC‐g‐AMPS superabsorbent hydrogel with antisalt and pH‐responsiveness properties

To synthesize a novel biopolymer‐based superabsorbent hydrogel, 2‐acrylamido‐2‐methylpropanesulfonic acid (AMPS) was grafted onto kappa‐carrageenan (κC) backbones. The graft copolymerization reaction was carried out in a homogeneous medium and in the presence of ammonium persulfate (APS) as an initiator, N,N,N′,N′‐tetramethyl ethylenediamine (TMEDA) as an accelerator, and N,N′‐methylene bisacrylamide (MBA) as a crosslinker. A proposed mechanism for κC‐g‐AMPS formation was suggested and the hydrogel structure was confirmed using FTIR spectroscopy. The affecting variables on swelling capacity, i.e., the initiator, the crosslinker, and the monomer concentration, as well as reaction temperature, were systematically optimized. The swelling measurements of the hydrogels were conducted in aqueous solutions of LiCl, NaCl, KCl, MgCl₂, CaCl₂, SrCl₂, BaCl₂, and AlCl₃. Due to the high swelling capacity in salt solutions, the hydrogels may be referred to as antisalt superabsorbents. The swelling of superabsorbing hydrogels was measured in solutions with pH ranging 1 to 13. The κC‐g‐AMPS hydrogel exhibited a pH‐responsiveness character so that a swelling–deswelling pulsatile behavior was recorded at pH 2 and 8. The overall activation energy for the graft copolymerization reaction was found to be 14.6 kJ/mol. The swelling kinetics of the hydrogels was preliminarily investigated as well. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 255–263, 2005     

Radiation synthesis of poly(N‐vinylpyrrolidone‐co‐methacrylic acid) hydrogels and their usability in uranyl ion adsorption

In this study, N‐vinylpyrrolidone(VP)/methacrylic acid (MAA) mixtures have been prepared at three different mole percents which the methacrylic acid composition around 5, 10, and 15%. Poly(N‐vinylpyrrolidone‐co‐methacrylicacid) P(VP/MAA) hydrogels irradiated at 3.4 kGy have been used for swelling and diffusion studies in water and uranyl ion solutions. The influence of dose, pH, relative amounts of monomers in MAA/VP monomer mixtures on the swelling properties have been investigated. P(VP/MAA) hydrogels were swollen in distilled water at pH 7.0. P(VP/MAA)1 hydrogel containing 36% (mole percent) methacrylic acid showed the maximum percent swelling in water. Adsorption isotherms were constructed for uranyl ions and P(VP/MAA) hydrogel systems. It has been found that P(VP/MAA) hydrogels have very high uptake of the uranyl ions succesfully in water containing uranyl ions. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Release of vitamin B12 from poly(N‐vinyl‐2‐pyrrolidone)‐crosslinked polyacrylamide hydrogels: A kinetic study

Hydrogels, composed of poly(N‐vinyl‐2‐pyrrolidone) and crosslinked polyacrylamide, were synthesized and the release of vitamin B₁₂ from these hydrogels was studied as a function of the degree of crosslinking and pH of the external swelling media. The three drug‐loaded hydrogel samples synthesized with different crosslinking ratios of 0.3, 0.7, and 1.2 (in mol %) follow different drug‐release mechanisms, that is, chain relaxation with zero‐order, non‐Fickian and Fickian, or diffusion‐controlled mechanisms. To establish a correlation between their swelling behavior and drug‐release mechanism, the former was studied by the weight‐gain method and, at the same time, the concentration of the drug released was studied colorimetrically. Various swelling parameters such as the swelling exponent n, gel‐characteristic constant k, penetration velocity v, and diffusion coefficient D were evaluated to reflect the quantitative aspect of the swelling behavior of these hydrogels. Finally, the drug‐release behavior of the hydrogels was explained by proposing the swelling‐dependent mechanism. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1706–1714, 2000     

Sustained release of potassium diclofenac from a pH‐responsive hydrogel based on gum arabic conjugates into simulated intestinal fluid

This work describes the preparation, the swelling properties and the potassium diclofenac (KDF) release profile of hydrogels of gum arabic (GA), N′,N′‐dimethylacrylamide, and methacrylic acid. In order to convert GA into a hydrogel, the polysaccharide was vinyl‐modified with glycidyl methacrylate. The hydrogels showed pH‐responsive swelling changes, which were more expressive in the basic environment. Release data of KDF were adjusted to a diffusion‐based kinetic model that provides an important insight on affinity of the drug for hydrogel and solvent, which may be the leading parameter for release of guest molecules from polymers. The KDF release from the hydrogels into simulated intestinal fluid decreases when the amount of modified GA increases. This was demonstrated to be due to the higher affinity of KDF for GA‐richer hydrogel, which makes the anti‐inflammatory release less favorable. The analysis of released drug half‐time (t_1/2 = 16.10 and 21.51 h) indicated sustained release characteristics. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43319.     

Photopolymerized pH‐sensitive semi‐IPN: Synthesis,water uptake analysis,and preliminary drug release study

A series of pH‐sensitive semi‐IPN hydrogels, composed of varying amounts of monomer acrylic acid(AAc), crosslinker N,N′ methylene bisacrylamide, polymer cellulose acetate (CA) were synthesized via photoinitiated polymerization in dimethyl formamide (DMF) medium. The CA/P (AAc) hydrogels were characterized by FTIR, and TG analysis. The equilibrium water uptake data was used to determine various network parameters. For all the samples synthesized, the swelling exponent “n,” initial diffusion coefficient D and average diffusion coefficient D_ave were found to be in the range of 0.51–0.72, 3.16 to 7.14 × 10^?6 cm² min^?1 and 94.16–120.56 cm² min^?1, respectively. The hydrogel demonstrated fair pH‐dependent swelling behavior, with nearly 20% swelling in the medium of pH 1.0 and 615% in the medium of pH 7.4 at 37°C, respectively. The gel showed excellent swelling–deswelling cycles which were interpreted quantitatively by first order kinetic swelling and deswelling models. Finally, the preliminary insulin release study, carried out in the media of varying pH, observed almost 16% release of entrapped drug in the simulating gastric fluid (SGF) of pH 1.0 in first 2 h and nearly 51% in next 6 h in simulating intestinal fluid(SIF) of pH 7.4 at 37°C. POLYM. ENG. SCI., 53:2129–2140, 2013. © 2013 Society of Plastics Engineers     

Swelling behavior of semi‐interpenetrating polymer network hydrogels composed of poly(vinyl alcohol) and poly(acrylamide‐co‐sodium methacrylate)

Interpenetrating polymer network (IPN) hydrogels based on poly(vinyl alcohol) (PVA) and poly(acrylamide‐co‐sodium methacrylate) poly(AAm‐co‐SMA) were prepared by the semi IPN method. These IPN hydrogels were prepared by polymerizing aqueous solution of acrylamide and sodium methacrylate, using ammonium persulphate/N,N,N¹,N¹‐tetramethylethylenediamine (APS/TMEDA) initiating system and N,N¹‐methylene‐bisacrylamide (MBA) as a crosslinker in the presence of a host polymer, poly(vinyl alcohol). The influence of reaction conditions, such as the concentration of PVA, sodium methacrylate, crosslinker, initiator, and reaction temperature, on the swelling behavior of these IPNs was investigated in detail. The results showed that the IPN hydrogels exhibited different swelling behavior as the reaction conditions varied. To verify the structural difference in the IPN hydrogels, scanning electron microscopy (SEM) was used to identify the morphological changes in the IPN as the concentration of crosslinker varied. In addition to MBA, two other crosslinkers were also employed in the preparation of IPNs to illustrate the difference in their swelling phenomena. The swelling kinetics, equilibrium water content, and water transport mechanism of all the IPN hydrogels were investigated. IPN hydrogels being ionic in nature, the swelling behavior was significantly affected by environmental conditions, such as temperature, ionic strength, and pH of the swelling medium. Further, their swelling behavior was also examined in different physiological bio‐fluids. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 302–314, 2005     

Kinetic degradation and controlled drug delivery system studies for sensitive hydrogels prepared by gamma irradiation

Ternary mixtures of N‐vinyl‐2‐pyrrolidone/itaconic acid and gelatin were irradiated by gamma rays at 30 kGy/s and at ambient temperature to prepared poly (NVP/IA and G) hydrogels. Poly (NVP/IA) hydrogels were prepared in different compositions (NVP/IA) mole ratio, (100/0), (98/1.5), (96.5/3.5), and (93/7.0) at 30 kGy. Then adding gelatin at different content (5, 10, 15, 20) mg to the best composition (NVP/IA/H₂O) (93/7)% for the characterization of network structure of these hydrogels, kinetic swelling drug release behavior and Scan Electron Microscope was studied. The equilibrium degree of swelling for P(NVP/IA) and P(NVP/IA/G) copolymer and the swelling‐degradation kinetics were also studies. According to dynamic swelling studies, both the diffusion exponent and the diffusion coefficient increase with increasing content of (IA), whereas, the addition of gelatin to (NVP/IA) composition by different content did not lead to any significant change in swelling percent. Also, the swelling behavior of copolymer hydrogels in response to pH value of the external media was studied, it is noted that the highest swelling values were at pH 4. The in vitro drug release behavior of these hydrogels was examined by quantification analysis with a UV/VIS spectrophotometers. Chlorpromazine hydrochloride was loaded into dried hydrogels to investigate the stimuli‐sensitive property at the specific pH and the drug release profile of these pH‐sensitive hydrogels in vitro. The release studies show that the highest value of release was at pH 4 which can be used for drug delivery system. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Release of fluorescent markers from phase‐separated gelatin‐maltodextrin hydrogels

Genipin‐crosslinked gelatin‐maltodextrin phase‐separated hydrogels consisting of gelatin‐continuous or bicontinuous microstructures were developed to regulate swelling and release behavior of four fluorescent markers of varying molecular weights [(fluorescein (332 Da) and FITC‐dextrans (FD) (4000–250,000 Da)]. Bicontinuous hydrogels showed significantly greater swelling than gelatin‐continuous hydrogels under all conditions (at pH 1.5 and 7.4 and three genipin/gelatin crosslinking ratios) (P < 0.05). With both microstructures, fluorescein showed the largest release rate and total release followed by FD 4000 Da, FD 40,000 Da, and FD 250,000 Da (P < 0.05). Marker molecular weight, pH, and crosslink ratio all affected the rate and amount of release. The mode of transport for the solvent and all markers was Fickian or slightly anomalous, with diffusional exponent (n) values ranging from 0.35 to 0.64. These results demonstrated that with the proper combination of crosslink density, solvent pH, and microstructure, hydrogels with a specified swelling behavior may be developed. This, coupled with a marker of appropriate size, can lead to controllable levels and rates of release. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Delivery of bupivacaine included in poly(acrylamide‐co‐monomethyl itaconate) hydrogels as a function of the pH swelling medium

Copolymeric hydrogels of poly(acrylamide‐co‐monomethyl itaconate) (A/MMI) crosslinked with N,N′‐methylenbisacrylamide (NBA) were synthesized as devices for the controlled release of bupivacaine (Bp). Two compositions of the copolymer, 60A/40MMI and 75A/25MMI, were studied. A local anesthetic was included in the feed mixture of polymerization (2–8 mg Bp/tablet) and by immersion of the copolymeric tablets in an aqueous solution of the drug. A very large amount of Bp (36–38 mg Bp/tablet) was included in the gels by sorption due to interactions between the drug and the side groups of the hydrogels. Swelling and drug release were in accordance with the second Fick's law at the first stages of the processes. The swelling behavior of these copolymers depended on the pH of the medium. The equilibrium swelling degree (W_∞) was larger at pH 7.5 (W_∞ ≈ 90 wt %) than at pH 1.5 (W_∞ ≈ 52–64 wt %) due to the ionization of the side groups of the copolymer. Release of the drug also depended on the pH of the swelling medium; at pH 7.5, about 60% of the included drug was released, and at pH 1.5, about 80% was released. Bp release was controlled by the comonomer composition of the gels, their drug‐load, and the pH of the swelling medium. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 327–334, 2002     

Interpenetrating polymeric network hydrogels for potential gastrointestinal drug release

New interpenetrating polymeric network (IPN) hydrogels based on chitosan (C), poly(N‐vinyl pyrrolidone) (PVP) and poly(acrylic acid) (PAAc), crosslinked with glutaraldehyde (G) and N,N‘‐methylenebisacrylamide (MBA), were prepared and investigated for potential gastrointestinal drug delivery vehicles utilizing a model drug, amoxicillin. IPN hydrogels were synthesized by simultaneous polymerization/crosslinking of acrylic acid monomer in the presence of another polymer (C) and crosslinker (G, MBA). Three different concentrations of glutaraldehyde were used (0.5, 1.0 and 2.0 w/w) to control the overall porosity of the hydrogels, named C‐P‐AAc/0.5, C‐P‐AAc/1.0 and C‐P‐AAc/2.0, respectively. Spectroscopic and thermal analyses such as Fourier transform infrared spectroscopy, thermogravimetric analysis and thermomechanical analysis were performed for IPN characterization. Equilibrium swelling studies were conducted for pH and temperature response behavior. Swelling studies were also carried out in simulated gastric fluid of pH = 1.1 and simulated intestinal fluid of pH = 7.4 to investigate possible site‐specific drug delivery. It was found that the release behavior of the drug from these IPN hydrogels was dependent on the pH of the medium and the proportion of crosslinker in the IPN. It was observed that amoxicillin release at pH = 7.4 was higher than at pH = 1.1. The analysis of the drug release showed that amoxicillin was released from these hydrogels through a non‐Fickian diffusion mechanism. Copyright © 2007 Society of Chemical Industry     

Fast responsive poly(acrylic acid‐co‐N‐isopropyl acrylamide) hydrogels based on new crosslinker

Novel dual temperature‐ and pH‐sensitive poly(acrylic acid‐co‐N‐isopropylacrylamide), AA/NIPAAm, hydrogels were successfully prepared by chemical crosslinking with crosslinkers. Copolymers of AA/NIPAAm were crosslinked in the presence of different mol % of N,N‐methylene bisacrylamide (MBA) and melamine triacrylamide (MAAm) as crosslinkers by bulk radical polymerization. The resultant xerogels were characterized by extracting the soluble fractions and measuring the equilibrium water content. Lower critical solution transition temperatures (LCST) were measured by DSC. The properties of crosslinked AA/NIPAAm series are evaluated in terms of compositional drift of polymerization, heterogeneous crosslinking, and chemical structure of the relevant components. Soluble fractions of the crosslinked networks were reduced by varying the MAAm and MBA concentrations. The influence of environmental conditions such as temperature and pH on the swelling behavior of these polymeric gels was investigated. The swelling behaviors of the resulting gels show pH sensitivity. The prepared MAAm type AA/NIPAAm hydrogels exhibited a more rapid deswelling rate than MBA type AA/NIPAAm hydrogels in ultra pure water in response to abrupt changes from 20°C to 50°C. The results of this study provide valuable information regarding the development of dual stimuli‐sensitive hydrogels with fast responsiveness. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and characterization of pH responsive poly(methacrylic acid‐acrylamide‐N‐hydroxyethyl acrylamide) hydrogels for drug delivery systems

In this study, pH responsive polymers composed of methacrylic acid, acrylamide, and N‐hydroxyethyl acrylamide were synthesized by free radical polymerization technique. The characterization was done with Fourier transform infrared spectroscopy and scanning electron microscopy. The swelling and drug release behavior of the hydrogels was determined as a function of time at 37°C in pH 2.1 and 7.4. The swelling and drug release studies showed that increased methacrylic acid amount caused a higher increase in swelling and drug release values at pH 7.4 than those at pH 2.1. In addition, the drug release data were applied to kinetic models such as zero order, first order, and Higuchi equations, and it fit well in the Higuchi model of the hydrogel. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43226.     

Preparation and characterization of novel cationic copolymer hydrogels with pH sensitivity and thermosensitivity

Cationic hydrogels were synthesized through the copolymerization of N‐isopropylacrylamide and dimethylaminoethylmethacrylate. N,N′‐Methylenebisacrylamide was used as a crosslinking agent, and sodium bisulfite/ammonium persulfate was used as an initiator. The equilibrium and dynamic swelling properties were investigated to reveal the pH sensitivity and thermosensitivity of the hydrogels. The conclusion was drawn that the prepared cationic hydrogels demonstrated critical sensitivity at 37°C and pH 7.0–8.0 and that the stronger the acidity was of the buffered solution, the shorter the equilibrium swelling time was of the hydrogels. Drug‐release experiments in vitro were carried out at 37°C (close to body temperature), at pH 1.4 (close to the pH of the stomach), and at pH 7.4 (close to the pH of the intestine). The release results indicated that the drug (chloramphenicol) was released more rapidly from the prepared hydrogel in a pH 1.4 buffered solution than in a pH 7.4 one, and this was consistent with the results predicted from the experiments of the swelling kinetics. Moreover, the drug‐release process was confirmed by scanning electron micrographs of the hydrogels embedded with chloramphenicol. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3602–3608, 2006     

Swelling characteristics and in vitro drug release study with pH‐ and thermally sensitive hydrogels based on modified chitosan

The grafting of a poly(ethylene glycol) diacrylate macromer onto a chitosan backbone was carried out with different macromer concentrations. The grafting was achieved by (NH₄)₂Ce(NO₃)₆‐induced free‐radical poly merization. Biodegradable, pH‐ and thermally responsive hydrogels of poly(ethylene glycol)‐g‐chitosan crosslinked with a lower amount of glutaraldehyde were prepared for controlled drug release studies. Both the graft copolymers and the hydrogels were characterized with Fourier transform infrared, elemental analysis, and scanning electron microscopy. The obtained hydrogels were subjected to equilibrium swelling studies at different temperatures (25, 37, and 45°C) in buffer solutions of pHs 2.1 and 7.4 (similar to those of gastric and intestinal fluids, respectively). 5‐Fluorouracil was entrapped in these hydrogels, and equilibrium swelling studies were carried out for the drug‐entrapped gels at pHs 2.1 and 7.4 and 37°C. The in vitro release profile of the drug was established at 37°C and pHs 2.1 and 7.4. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 977–985, 2006     

Oxaliplatin‐loaded crosslinked polymeric network of chondroitin sulfate‐co‐poly(methacrylic acid) for colorectal cancer: Its toxicological evaluation

The purpose of this study was to develop and characterize chemically crosslinked chondroitin sulfate‐co‐poly(methacrylic acid) (CSMA) hydrogels for colon targeting of oxaliplatin (OXP) to treat colorectal cancer. CSMA hydrogels were synthesized by free‐radical polymerization. Chondroitin sulfate was chemically crosslinked with methacrylic acid in an aqueous medium. Ammonium peroxodisulfate and N,N‐methylene bisacrylamide were used as the initiator and crosslinker, respectively. Fourier transform infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, X‐ray diffraction, and scanning electron microscopy studies were performed to characterize the fabricated polymeric system. The pH‐sensitive characteristics of the hydrogels were evaluated by swelling dynamics and equilibrium swelling ratio measurements at pH 1.2 and 7.4. A toxicity study of the developed formulations was also conducted on rabbits to determine the toxicity of the drug‐carrier system to the biological system. The characterization studies confirmed the formation of a new polymeric network. A high OXP loading and higher drug release was observed at pH 7.4. The toxicity study confirmed that the developed formulations were nontoxic to the biological system. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45312.     

Thermo‐ and pH‐sensitive hydrogels based on 2‐(2‐methoxyethoxy)ethyl methacrylate and methacrylic acid

Hydrogels based on commercially available 2‐(2‐methoxyethoxy)ethyl methacrylate (MEO₂MA), with methacrylic acid (MAA) as comonomer, are studied. The incorporation of an ionizable monomer, such as MAA, in a thermosensitive system leads to the formation of hydrogels able to respond to pH and temperature according to their monomeric composition. Thus, at low pH, the acid groups of MAA are protonated, and they do not contribute to increase the hydrophilic balance, and collapse of the hydrogels occurs around room temperature. For temperatures below that of collapse, the degree of swelling increases with increasing MEO₂MA content. In contrast, at neutral or basic pH, the ionization of the acid groups contributes to increase the hydrophilicity and the osmotic pressure, leading to polyelectrolyte behaviour. In this regime, the swelling capacity increases and the thermosensitivity decreases with increasing MAA content in the hydrogels. These properties make poly(MEO₂MA‐co‐MAA) hydrogels suitable candidates for use in oral controlled delivery of hydrophobic drugs. This possibility is explored using ibuprofen as a model drug, after a complete study of the swelling kinetics. Copyright © 2010 Society of Chemical Industry     

Swelling and hydrolytic degradation behaviour of pH‐responsive hydrogels of poly[(N‐isopropylacrylamide)‐co‐(methacrylic acid)] crosslinked by biodegradable polycaprolactone chains

BACKGROUND: Stimuli‐responsive hydrogels are typically obtained from non‐biodegradable monomers. The use of biodegradable crosslinkers can overcome this limitation. In this context, the main aim of this work was to use modified polycaprolactone as a crosslinker in the preparation of pH‐responsive hydrogels based on N‐isopropylacrylamide and methacrylic acid to give poly[(N‐isopropylacrylamide)‐co‐(methacrylic acid)] (P(N‐iPAAm‐co‐MAA)). RESULTS: Poly(caprolactone) dimethacrylate macromonomer was synthesized and successfully employed as crosslinker with various ratios in the synthesis of well‐known pH‐responsive hydrogels of P(N‐iPAAm‐co‐MAA). The swelling properties of these degradable hydrogels were investigated. They practically do not swell at pH = 2, but exhibit a very high swelling capacity in distilled water and in solutions of pH = 7. In addition, degradation studies at pH = 12 showed that the hydrolysis of the ester groups in the polycaprolactone chains produces, after a relatively short time, the total solubilization of the polymer chains. CONCLUSION: The hydrogels under study have certain characteristics that could make them good candidates for use as matrices in controlled drug delivery. On the one hand, they do not swell in acid pH solution (stomach conditions) but they swell extensively at neutral pH. On the other hand, they became rapidly water soluble following degradation. Copyright © 2009 Society of Chemical Industry